Document the R8A7795-specific DT bindings and support them in the
driver. The HDMI and LVDS outputs are currently not supported.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The ODDF signal, output by default on the ODDF pin, isn't used on any
board supported in the kernel. As the Gen3 Salvator-X board uses the
ODDF pin as a DISP signal, hardcode that configuration in the driver.
Use of the ODDF signal will be implemented later through proper DT-based
configuration of the DU pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Plane sources are configured by the VSPS bit in the PnDDCR4 register.
Although the datasheet states that the bit is updated during vertical
blanking, it seems that updates only occur when the DU group is held in
reset through the DSYSR.DRES bit. Restart the group if the source
changes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Configure the plane source at plane setup time to source frames from
memory or from the VSP1.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7794 DU has a fixed output routing configuration with one RGB
output per CRTC and thus lacks the RGB output routing register field.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Changing the plane to CRTC associations requires restarting the CRTC
group, creating visible flicker. Mitigate the issue by changing plane
association only when a plane becomes enabled, not when it get disabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The DU uses the module functional clock as the default pixel clock, but
supports using an externally supplied pixel clock instead. Support this
by adding the external pixel clock to the DT bindings, and selecting the
clock automatically at runtime based on the requested mode pixel
frequency.
The input clock pins to DU channels routing is configurable, but
currently hardcoded to connect input clock i to channel i.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Rename the feature from RCAR_DU_FEATURE_DEFR8 to
RCAR_DU_FEATURE_EXT_CTRL_REGS to cover all extended control registers in
addition to the DEFR8 register.
Usage of the feature is refactored to optimize runtime operation and
prepare for external clock support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The "Renesas Corporation" listed in the copyright notice doesn't exist.
Replace it with "Renesas Electronics Corporation" and update the
copyright years.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7790 DU variant has a single RGB output called DPAD0 that can be
fed with the output of DU0, DU1 or DU2. Making the routing configurable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Split the output routing specification between SoC-internal data,
specified in the rcar_du_device_info structure, and board data, passed
through platform data.
The DU has 5 possible outputs (DPAD0/1, LVDS0/1, TCON). SoC-internal
output routing data specify which output are valid, which CRTCs can be
connected to the valid outputs, and the type of in-SoC encoder for the
output.
Platform data then specifies external encoders and the output they are
connected to.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Output routing is configured in group registers, move the corresponding
code from rcar_du_crtc.c to rcar_du_group.c.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7779 DU is split in per-CRTC resources (scan-out engine, blending
unit, timings generator, ...) and device-global resources (start/stop
control, planes, ...) shared between the two CRTCs.
The R8A7790 introduced a third CRTC with its own set of global resources
This would be modeled as two separate DU device instances if it wasn't
for a handful or resources that are shared between the three CRTCs
(mostly related to input and output routing). For this reason the
R8A7790 DU must be modeled as a single device with three CRTCs, two sets
of "semi-global" resources, and a few device-global resources.
Introduce a new rcar_du_group driver-specific object, without any real
counterpart in the DU documentation, that models those semi-global
resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
