- Add support for host software queue for (e)MMC/SD
- Throttle polling rate for CMD6
- Update CMD13 busy condition check for CMD6 commands
- Improve busy detect polling for erase/trim/discard/HPI
- Fixup support for HW busy detection for HPI commands
- Re-work and improve support for eMMC sanitize commands
MMC host:
- mmci: Add support for sdmmc variant revision 2.0
- mmci_sdmmc: Improve support for busyend detection
- mmci_sdmmc: Fixup support for signal voltage switch
- mmci_sdmmc: Add support for tuning with delay block
- mtk-sd: Fix another SDIO irq issue
- sdhci: Disable native card detect when GPIO based type exist
- sdhci: Add option to defer request completion
- sdhci_am654: Add support to set a tap value per speed mode
- sdhci-esdhc-imx: Add support for i.MX8MM based variant
- sdhci-esdhc-imx: Fixup support for standard tuning on i.MX8 usdhc
- sdhci-esdhc-imx: Optimize for strobe/clock dll settings
- sdhci-esdhc-imx: Fixup support for system and runtime suspend/resume
- sdhci-iproc: Update regulator/bus-voltage management for bcm2711
- sdhci-msm: Prevent clock gating with PWRSAVE_DLL on broken variants
- sdhci-msm: Fix management of CQE during SDHCI reset
- sdhci-of-arasan: Add support for auto tuning on ZynqMP based platforms
- sdhci-omap: Add support for system suspend/resume
- sdhci-sprd: Add support for HW busy detection
- sdhci-sprd: Enable support host software queue
- sdhci-tegra: Add support for HW busy detection
- tmio/renesas_sdhi: Enforce retune after runtime suspend
- renesas_sdhi: Use manual tap correction for HS400 on some variants
- renesas_sdhi: Add support for manual correction of tap values for tunings
-----BEGIN PGP SIGNATURE-----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=gILc
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for host software queue for (e)MMC/SD
- Throttle polling rate for CMD6
- Update CMD13 busy condition check for CMD6 commands
- Improve busy detect polling for erase/trim/discard/HPI
- Fixup support for HW busy detection for HPI commands
- Re-work and improve support for eMMC sanitize commands
MMC host:
- mmci:
* Add support for sdmmc variant revision 2.0
- mmci_sdmmc:
* Improve support for busyend detection
* Fixup support for signal voltage switch
* Add support for tuning with delay block
- mtk-sd:
* Fix another SDIO irq issue
- sdhci:
* Disable native card detect when GPIO based type exist
- sdhci:
* Add option to defer request completion
- sdhci_am654:
* Add support to set a tap value per speed mode
- sdhci-esdhc-imx:
* Add support for i.MX8MM based variant
* Fixup support for standard tuning on i.MX8 usdhc
* Optimize for strobe/clock dll settings
* Fixup support for system and runtime suspend/resume
- sdhci-iproc:
* Update regulator/bus-voltage management for bcm2711
- sdhci-msm:
* Prevent clock gating with PWRSAVE_DLL on broken variants
* Fix management of CQE during SDHCI reset
- sdhci-of-arasan:
* Add support for auto tuning on ZynqMP based platforms
- sdhci-omap:
* Add support for system suspend/resume
- sdhci-sprd:
* Add support for HW busy detection
* Enable support host software queue
- sdhci-tegra:
* Add support for HW busy detection
- tmio/renesas_sdhi:
* Enforce retune after runtime suspend
- renesas_sdhi:
* Use manual tap correction for HS400 on some variants
* Add support for manual correction of tap values for tunings"
* tag 'mmc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: cavium-octeon: remove nonsense variable coercion
mmc: mediatek: fix SDIO irq issue
mmc: mmci_sdmmc: Fix clear busyd0end irq flag
dt-bindings: mmc: Fix node name in an example
mmc: core: Re-work the code for eMMC sanitize
mmc: sdhci: use FIELD_GET for preset value bit masks
mmc: sdhci-of-at91: Display clock changes for debug purpose only
mmc: sdhci: iproc: Add custom set_power() callback for bcm2711
mmc: sdhci: am654: Use sdhci_set_power_and_voltage()
mmc: sdhci: at91: Use sdhci_set_power_and_voltage()
mmc: sdhci: milbeaut: Use sdhci_set_power_and_voltage()
mmc: sdhci: arasan: Use sdhci_set_power_and_voltage()
mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()
mmc: vub300: Use scnprintf() for avoiding potential buffer overflow
dt-bindings: mmc: synopsys-dw-mshc: fix clock-freq-min-max in example
sdhci: tegra: Enable MMC_CAP_WAIT_WHILE_BUSY host capability
sdhci: tegra: Implement Tegra specific set_timeout callback
mmc: sdhci-omap: Add Support for Suspend/Resume
mmc: renesas_sdhi: simplify execute_tuning
mmc: renesas_sdhi: Use BITS_PER_LONG helper
...
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- A couple of x86/cpu cleanups and changes were grandfathered in due
to patch dependencies. These clean up the set of CPU model/family
matching macros with a consistent namespace and C99 initializer
style.
- A bunch of updates to various low level PMU drivers:
* AMD Family 19h L3 uncore PMU
* Intel Tiger Lake uncore support
* misc fixes to LBR TOS sampling
- optprobe fixes
- perf/cgroup: optimize cgroup event sched-in processing
- misc cleanups and fixes
Tooling side changes are to:
- perf {annotate,expr,record,report,stat,test}
- perl scripting
- libapi, libperf and libtraceevent
- vendor events on Intel and S390, ARM cs-etm
- Intel PT updates
- Documentation changes and updates to core facilities
- misc cleanups, fixes and other enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
cpufreq/intel_pstate: Fix wrong macro conversion
x86/cpu: Cleanup the now unused CPU match macros
hwrng: via_rng: Convert to new X86 CPU match macros
crypto: Convert to new CPU match macros
ASoC: Intel: Convert to new X86 CPU match macros
powercap/intel_rapl: Convert to new X86 CPU match macros
PCI: intel-mid: Convert to new X86 CPU match macros
mmc: sdhci-acpi: Convert to new X86 CPU match macros
intel_idle: Convert to new X86 CPU match macros
extcon: axp288: Convert to new X86 CPU match macros
thermal: Convert to new X86 CPU match macros
hwmon: Convert to new X86 CPU match macros
platform/x86: Convert to new CPU match macros
EDAC: Convert to new X86 CPU match macros
cpufreq: Convert to new X86 CPU match macros
ACPI: Convert to new X86 CPU match macros
x86/platform: Convert to new CPU match macros
x86/kernel: Convert to new CPU match macros
x86/kvm: Convert to new CPU match macros
x86/perf/events: Convert to new CPU match macros
...
In this function, the variable 'base' is already 'void __iomem *base',
and the return function 'devm_platform_ioremap_resource()' also returns
this type, so the mandatory definition here is redundant.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20200327043639.6564-1-tangbin@cmss.chinamobile.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO irq is not triggered by low level, but by falling edge in our
previous IC. This mechanism only have one chance to catch the SDIO irq
if a SDIO irq comes within the multiple block transmission. This SDIO
irq may be easily lost, because falling edge appears only once within 2
clock after data transmission is completed.
SDIO irq recheck mechanism will make sure all irqs can be
processed correctly.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/1585299097-6897-2-git-send-email-yong.mao@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The busyd0 line transition can be very fast. The busy request may be
completed by busy_d0end, without waiting for the busy_d0 steps. Therefore,
clear the busyd0end irq flag, even if no busy_status.
Fixes: 0e68de6aa7 ("mmc: mmci: sdmmc: add busy_complete callback")
Cc: stable@vger.kernel.org
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200325143409.13005-2-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The error path for sanitize operations that completes with -ETIMEDOUT, is
tightly coupled with the internal request handling code of the core. More
precisely, mmc_wait_for_req_done() checks for specific sanitize errors.
This is not only inefficient as it affects all types of requests, but also
hackish.
Therefore, let's improve the behaviour by moving the error path out of the
mmc core. To do that, retuning needs to be held while running the sanitize
operation.
Moreover, to avoid exporting unnecessary symbols to the mmc block module,
let's move the code into the mmc_ops.c file. While updating the actual
code, let's also take the opportunity to clean up some of the mess around
it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200316152152.15122-1-ulf.hansson@linaro.org
The new macro set has a consistent namespace and uses C99 initializers
instead of the grufty C89 ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lkml.kernel.org/r/20200320131510.285691129@linutronix.de
The sdhci_at91_set_clks_presets() function is called multiple times at
runtime and the messages are shown on the console. Display clk mul, gck
rate and clk base for debug purpose only.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200312142904.232822-1-tudor.ambarus@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The controller needs a valid bus voltage in its power register
regardless of whether an external regulator is taking care of the power
supply.
The sdhci core already provides a helper function for this,
sdhci_set_power_and_bus_voltage(), so create a bcm2711 specific 'struct
sdhci_ops' which makes use of it.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200306174413.20634-10-nsaenzjulienne@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci core provides a helper function with the same functionality as
this controller's set_power() callback. Use it instead.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200306174413.20634-8-nsaenzjulienne@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci core provides a helper function with the same functionality as
this controller's set_power() callback. Use it instead.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200306174413.20634-5-nsaenzjulienne@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci core provides a helper function with the same functionality as
this controller's set_power() callback. Use it instead.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200306174413.20634-4-nsaenzjulienne@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci core provides a helper function with the same functionality as
this controller's set_power() callback. Use it instead.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200306174413.20634-3-nsaenzjulienne@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers diverge from the standard way of setting power and need
their bus voltage register to be configured regardless of the whether
they use regulators. As this is a common pattern across sdhci hosts,
create a helper function.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200306174413.20634-2-nsaenzjulienne@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311080439.13928-1-tiwai@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tegra host supports HW busy detection and timeouts based on the
count programmed in SDHCI_TIMEOUT_CONTROL register and max busy
timeout it supports is 11s in finite busy wait mode.
Some operations like SLEEP_AWAKE, ERASE and flush cache through
SWITCH commands take longer than 11s and Tegra host supports
infinite HW busy wait mode where HW waits forever till the card
is busy without HW timeout.
This patch implements Tegra specific set_timeout sdhci_ops to allow
switching between finite and infinite HW busy detection wait modes
based on the device command expected operation time.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1583941675-9884-1-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add power management ops which save and restore the driver context and
facilitate a system suspend and resume.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200305151228.24692-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update cqhci memory ioresource name from cqhci_mem to cqhci since
suffix _mem is redundant.
Only sdhci-msm driver is making use of this resource as of now.
No other vendor's driver is using it. So this update shouldn't affect
any other vendor's cqhci functionality.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1583328320-9981-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When SDHC gets reset (E.g. in runtime suspend path), CQE also gets
reset and goes to disable state. But s/w state still points it as CQE
is in enabled state. Since s/w and h/w states goes out of sync,
it results in s/w request timeout for subsequent CQE requests.
To synchronize CQE s/w and h/w state during SDHC reset,
explicitly deactivate CQE just before SDHC reset.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1583503724-13943-3-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host controllers can reset CQHCI either directly or as a consequence of
host controller reset. Add cqhci_deactivate() which puts the CQHCI
driver into a state that is consistent with that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1583503724-13943-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200226223125.GA20630@embeddedor
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Supply a separate sg list for each of the request in non-blocking
IO test cases where two requests will be issued at same time.
Otherwise, sg memory may get unmapped when a request is done while
same memory is being accessed by controller from the other request,
and it leads to iommu errors with below call stack:
__arm_lpae_unmap+0x2e0/0x478
arm_lpae_unmap+0x54/0x70
arm_smmu_unmap+0x64/0xa4
__iommu_unmap+0xb8/0x1f0
iommu_unmap_fast+0x38/0x48
__iommu_dma_unmap+0x88/0x108
iommu_dma_unmap_sg+0x90/0xa4
sdhci_post_req+0x5c/0x78
mmc_test_start_areq+0x10c/0x120 [mmc_test]
mmc_test_area_io_seq+0x150/0x264 [mmc_test]
mmc_test_rw_multiple+0x174/0x1c0 [mmc_test]
mmc_test_rw_multiple_sg_len+0x44/0x6c [mmc_test]
mmc_test_profile_sglen_wr_nonblock_perf+0x6c/0x94 [mmc_test]
mtf_test_write+0x238/0x3cc [mmc_test]
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582714668-17247-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Spreadtrum host controller supports HW busy detection for commands with
R1B responses, but also for I/O operations. This means when the host gets a
transfer complete event, that always indicates the busy signal is released.
Let's inform the mmc core about this, via setting the corresponding
MMC_CAP_WAIT_WHILE_BUSY flag, as to remove some redundant software busy
polling.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/96f16647f6a6e8cb058c44e46c61b122df027059.1582535202.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, when use standard tuning, driver default disable DMA just before
send tuning command. But on i.MX8 usdhc, this is not enough. Need also clear
DMA_SEL. If not, once the DMA_SEL select AMDA2 before, even dma already disabled,
when send tuning command, usdhc will still prefetch the ADMA script from wrong
DMA address, then we will see IOMMU report some error which show lack of TLB
mapping.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-7-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since L4.15, community involve the commit 105819c8a545 ("mmc: core: use mrq->sbc
when sending CMD23 for RPMB"), let the usdhc to decide whether to use ACMD23 for
RPMB. This CMD23 for RPMB need to set the bit 31 to its argument, if not, the
RPMB write operation will return general fail.
According to the sdhci logic, SDMA mode will disable the ACMD23, and only in
ADMA mode, it will chose to use ACMD23 if the host support. But according to
debug, and confirm with IC, the imx6qpdl/imx6sx/imx6sl/imx7d do not support
the ACMD23 feature completely. These SoCs only use the 16 bit block count of
the register 0x4 (BLOCK_ATT) as the CMD23's argument in ACMD23 mode, which
means it will ignore the upper 16 bit of the CMD23's argument. This will block
the reliable write operation in RPMB, because RPMB reliable write need to set
the bit31 of the CMD23's argument. This is the hardware limitation. So for
imx6qpdl/imx6sx/imx6sl/imx7d, it need to broke the ACMD23 for eMMC, SD card do
not has this limitation, because SD card do not support reliable write.
For imx6ul/imx6ull/imx6sll/imx7ulp/imx8, it support the ACMD23 completely, it
change to use the 0x0 register (DS_ADDR) to put the CMD23's argument in ADMA mode.
This patch add a new flag ESDHC_FLAG_BROKEN_AUTO_CMD23, and add this flag to
imx6q/imx6sx/imx6sl/imx7d, and due to the imx6sll share the same compatible string
with imx6sx before, and imx6sll do not has this limitation, so add a new compatible
string for imx6sll.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-4-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After set the STROBE SLV delay target value, it need to wait some
time to let the usdhc lock the REF and SLV clock. In normal case,
1~2us is enough for imx8/imx6 and imx7d, and 4~5us is enough for
imx7ulp, but when do reboot stress test or do the bind/unbind stress
test, sometimes need to wait about 10us to get the status lock.
This patch optimize delay handle method, only print the warning
message if the status is still not lock after 1ms delay.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-3-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When force clock off, check the SDOFF of register PRSSTAT to make sure
the clock is gate off. Before force clock on, check the SDSTB of register
PRSSTAT to make sure the clock is stable, this will eliminate the clock
glitch.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-2-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
strobe-dll-delay-target is the delay cell add on the strobe line.
Strobe line the the uSDHC loopback read clock which is use in HS400
mode. Different strobe-dll-delay-target may need to set for different
board/SoC. If this delay cell is not set to an appropriate value,
we may see some read operation meet CRC error after HS400 mode select
which already pass the tuning.
This patch add the strobe-dll-delay-target setting in driver, so that
user can easily config this delay cell in dts file.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When pm_runtime_suspend is run, a call to SCFW power off the SS (SS is a
power domain, usdhc belong to this SS power domain) in which the resource
resides is made. The SCFW can power off the SS if no other resource in
active in that SS. If so, all state associated with all the resources within
the SS that is powered off is lost, this includes the clock rates, clock state
etc. When pm_runtime_resume is called, the SS associated with that resource
is powered up. But the clocks are left in the default state.
This patch restore clock rate in pm_runtime_resume, make sure the
clock is right rather than depending on the default state setting
by SCFW.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100563-20555-5-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For Mega/Mix enabled SoCs like MX7D and MX6SX, uSDHC will lost power in
LP mode no matter whether the MMC_KEEP_POWER flag is set or not.
This may cause state misalign between kernel and HW, especially for
SDIO3.0 WiFi cards.
e.g. SDIO WiFi driver usually will keep power during system suspend.
And after resume, no card re-enumeration called.
But the tuning state is lost due to Mega/Mix.
Then CRC error may happen during next data transfer.
So we should always fire a mmc_retune_needed() for such type SoC
to tell MMC core retuning is needed for next data transfer.
mmc: sdhci-esdhci-imx: retune needed for Mega/Mix enabled SoCs
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100563-20555-4-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using jailhouse to support two Linux on i.MX8MQ EVK, we use the
1st Linux to configure pinctrl for the 2nd Linux. Then the 2nd Linux
could use the mmc without pinctrl driver.
So give a warning message when no pinctrl available, but no fail probe.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1582100563-20555-3-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Except SDHCI_QUIRK_BROKEN_CARD_DETECTION and MMC_CAP_NONREMOVABLE,
we also do not need to handle controller native card detect interrupt
for gpio cd type.
If we wrong enabled the card detect interrupt for gpio case, it will
cause a lot of unexpected card detect interrupts during data transfer
which should not happen.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1582100563-20555-2-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Its recommended that DLL must only be enabled for SDR50, DDR50, DDR52,
SDR104, HS200 and HS400 speed modes. Move DLL configuration to its own
function and call it only in the above speed modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108150920.14547-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the latest AM65x Data Manual[1], a different output tap
delay value is optimum for a given speed mode. Therefore, deprecate the
ti,otap-del-sel binding and introduce a new binding for each of the
possible MMC/SD speed modes. If the legacy mode is not found, fall back
to old binding to maintain dts compatibility.
[1] http://www.ti.com/lit/gpn/am6526
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108150920.14547-3-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add missing MODULE_LICENSE() and MODULE_DESCRIPTION() in hsq driver to
fix below warning when compiling the hsq as a module.
"WARNING: modpost: missing MODULE_LICENSE() in drivers/mmc/host/mmc_hsq.o".
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/98ce471185f037fce57520763621590588766381.1582161803.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a sdmmc variant revision 2.0. This revision is backward
compatible with 1.1, but adds DMA linked list support.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-10-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prepare the voltage switch procedure, the VSWITCHEN bit must be set
before sending the CMD11. To confirm completion of voltage switch, the
VSWEND flag must be checked.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-9-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A variant may need to define some actions before and after a voltage
switch.
This patch adds 2 callbacks to manage signal voltage switch in the struct
mmci_host_ops. ->pre_sig_volt_switch() allows to prepare a signal voltage
switch before sending the SD_SWITCH_VOLTAGE command (CMD11).
->post_sig_volt_switch callback allows specific actions to be executed,
after the I/O signal voltage level has been changed.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-8-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware delay block is used to align the sampling clock on the data
received by SDMMC. It is mandatory for SDMMC to support the SDR104 mode.
The delay block is used to generate an output clock which is dephased from
the input clock. The phase of the output clock must be programmed by the
execute tuning interface.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-7-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In variant init function, some references may be allocated for variant
specific usage. Add a private void* to mmci_host struct allows at variant
functions to access on this references by mmci_host structure.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-5-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
