Commit 09124e19 ("RDMA/nes: Add support for KR device id 0x0110") took
out too much code and broke CX4 link detection in back-to-back
configuration. Put back the code that does the link check.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clear the stall bit to drop any incoming packets while destroying NIC
QP. This will prevent a chip resource leak.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set assume_aligned_header bit in QP context as requested by hardware group.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a hot-plug LLD removal event or an EEH error event, iw_cxgb3
must ensure that any/all threads that might be in a cxgb3 exported
function must return from the function before iw_cxgb3 returns from
its event processing. Do this by calling synchronize_net().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When an iWARP device is unloaded, the ib_mad module logs errors. It
should be ignoring iWARP devices on device removal just like it does
on device add.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Print the return code of ib_post_send() if it fails to make these
debugging messages more useful.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPoIB UD QP reports send completions to priv->send_cq, which is
usually left unarmed; it only gets armed when the number of
outstanding send requests reaches the size of the TX queue. This
arming is done only in the send path for the UD QP. However, when
sending CM packets, the net queue may be stopped for the same reasons
but no measures are taken to recover the UD path from a lockup.
Consider this scenario: a host sends high rate of both CM and UD
packets, with a TX queue length of N. If at some time the number of
outstanding UD packets is more than N/2 and the overall outstanding
packets is N-1, and CM sends a packet (making the number of
outstanding sends equal N), the TX queue will be stopped. When all
the CM packets complete, the number of outstanding packets will still
be higher than N/2 so the TX queue will not be restarted.
Fix this by calling ib_req_notify_cq() when the queue is stopped in
the CM path.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert some drivers who export a single string as class attribute
to the new class_attr_string functions. This removes redundant
code all over.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.
Also drivers can extend the attributes with own data fields
and use that in the low level function.
This makes the class attributes the same as sysdev_class attributes
and plain attributes.
This will allow further cleanups in drivers.
Full tree sweep converting all users.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
init: Open /dev/console from rootfs
mqueue: fix typo "failues" -> "failures"
mqueue: only set error codes if they are really necessary
mqueue: simplify do_open() error handling
mqueue: apply mathematics distributivity on mq_bytes calculation
mqueue: remove unneeded info->messages initialization
mqueue: fix mq_open() file descriptor leak on user-space processes
fix race in d_splice_alias()
set S_DEAD on unlink() and non-directory rename() victims
vfs: add NOFOLLOW flag to umount(2)
get rid of ->mnt_parent in tomoyo/realpath
hppfs can use existing proc_mnt, no need for do_kern_mount() in there
Mirror MS_KERNMOUNT in ->mnt_flags
get rid of useless vfsmount_lock use in put_mnt_ns()
Take vfsmount_lock to fs/internal.h
get rid of insanity with namespace roots in tomoyo
take check for new events in namespace (guts of mounts_poll()) to namespace.c
Don't mess with generic_permission() under ->d_lock in hpfs
sanitize const/signedness for udf
nilfs: sanitize const/signedness in dealing with ->d_name.name
...
Fix up fairly trivial (famous last words...) conflicts in
drivers/infiniband/core/uverbs_main.c and security/tomoyo/realpath.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (48 commits)
IB/srp: Clean up error path in srp_create_target_ib()
IB/srp: Split send and recieve CQs to reduce number of interrupts
RDMA/nes: Add support for KR device id 0x0110
IB/uverbs: Use anon_inodes instead of private infinibandeventfs
IB/core: Fix and clean up ib_ud_header_init()
RDMA/cxgb3: Mark RDMA device with CXIO_ERROR_FATAL when removing
RDMA/cxgb3: Don't allocate the SW queue for user mode CQs
RDMA/cxgb3: Increase the max CQ depth
RDMA/cxgb3: Doorbell overflow avoidance and recovery
IB/core: Pack struct ib_device a little tighter
IB/ucm: Clean whitespace errors
IB/ucm: Increase maximum devices supported
IB/ucm: Use stack variable 'base' in ib_ucm_add_one
IB/ucm: Use stack variable 'devnum' in ib_ucm_add_one
IB/umad: Clean whitespace
IB/umad: Increase maximum devices supported
IB/umad: Use stack variable 'base' in ib_umad_init_port
IB/umad: Use stack variable 'devnum' in ib_umad_init_port
IB/umad: Remove port_table[]
IB/umad: Convert *cdev to cdev in struct ib_umad_port
...
The iscsi_eh_target_reset has been modified to attempt
target reset only. If it fails, then iscsi_eh_session_reset
will be called.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Instead of repeating the error unwinding steps in each place an error
can be detected, use the common idiom of gotos into an error flow.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We can reduce the number of IB interrupts from two interrupts per
srp_queuecommand() call to one by using separate CQs for send and
receive completions and processing send completions by polling every
time a TX IU is allocated.
Receive completion events still trigger an interrupt.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Apparently bogus mc address can break IPOIB multicast processing. Therefore
returning the check for addrlen back until this is resolved in bonding (I don't
see any other point from where mc address with non-dev->addr_len length can came
from).
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the loop complexicity in nes_nic.c, I'm using char* to copy mc addresses
to it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for KR device id 0x0110. While at it, cleanup
nes_init_phy() by splitting it into nes_init_1g_phy() and
nes_init_2025_phy().
Remove support for NES_PHY_TYPE_IRIS, which was used on an XFP board
that was only manufactured in small quantities and given out for evals
in even smaller quantities.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The anon_inodes interface has been split to allow creating a bare
(non-installed) file pointer and also extended to allow specifying
O_RDONLY in the flags. This makes it a suitable replacement for the
private "infinibandeventfs" pseudo-filesystem used by uverbs, and this
replacement saves a small chunk of boilerplate code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_ud_header_init() first clears header and then fills up the various
fields. Later on, it tests header->immediate_present, which it has
already cleared, so the condition is always false. Fix this by adding
an immediate_present parameter and setting header->immediate_present
as is done with grh_present. Also remove unused calculation of
header_len.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If cxgb3 calls the iw_cxgb3 t3cclient remove function due to a device
removal event, then the iwch device must be marked with CXIO_ERROR_FATAL
since the device below us is going away. Otherwise, we can get stuck in
a deadlock as RDMA ULPs try and deallocate objects (like MRs, QPs, etc).
So always mark the device with CXIO_ERROR_FATAL when removing.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only kernel mode CQs need the SW queue memory allocated. The SW queue
for user mode CQs is allocated in userspace by libcxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
T3 hardware doorbell FIFO overflows can cause application stalls due
to lost doorbell ring events. This has been seen when running large
NP IMB alltoall MPI jobs. The T3 hardware supports an xon/xoff-type
flow control mechanism to help avoid overflowing the HW doorbell FIFO.
This patch uses these interrupts to disable RDMA QP doorbell rings
when we near an overflow condition, and then turn them back on (and
ring all the active QP doorbells) when when the doorbell FIFO empties
out. In addition if an doorbell ring is dropped by the hardware, the
code will now recover.
Design:
cxgb3:
- enable these DB interrupts
- in the interrupt handler, schedule work tasks to call the ULPs event
handlers with the new events.
- ring all the qset txqs when an overflow is detected.
iw_cxgb3:
- disable db ringing on all active qps when we get the DB_FULL event
- enable db ringing on all active qps and ring all active dbs when we get
the DB_EMPTY event
- On DB_DROP event:
- disable db rings in the event handler
- delay-schedule a work task which rings and enables the dbs on
all active qps.
- in post_send and post_recv logic, don't ring the db if it's disabled.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some large systems may support more than IB_UCM_MAX_DEVICES
(currently 32).
This change allows us to support more devices in a backwards-compatible
manner. the first IB_UCM_MAX_DEVICES keep the same major/minor device
numbers they've always had.
If there are more than IB_UCM_MAX_DEVICES, then we dynamically request
a new major device number (new minors start at 0).
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but sets us up for a future
change that allows us to support more than IB_UCM_MAX_DEVICES.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but sets us up for a future
change that allows us to dynamically allocate device numbers in case
we have more than IB_UCM_MAX_DEVICES in the system.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean errors as shown when 'let c_space_errors=1' is set in vim.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some large systems may support more than IB_UMAD_MAX_PORTS
(currently 64).
This change allows us to support more ports in a backwards-compatible
manner. The first IB_UMAD_MAX_PORTS keep the same major/minor device
numbers they've always had.
If there are more than IB_UMAD_MAX_PORTS, we then dynamically request
a new major device number (new minors start at 0).
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but sets us up for a future change
that allows us to support more than IB_UMAD_MAX_PORTS in a system.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but sets us up for a future
change that allows us to dynamically allocate device numbers in case
we have more than IB_UMAD_MAX_PORTS in the system.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We no longer need this data structure, as it was used to associate an
inode back to a struct ib_umad_port during ->open(). But now that
we're embedding a struct cdev in struct ib_umad_port, we can use the
container_of() macro to go from the inode back to the device instead.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Instead of storing pointers to cdev and sm_cdev, embed the full
structures instead.
This change allows us to use the container_of() macro in ib_umad_open()
and ib_umad_sm_open() in a future patch.
This change increases the size of struct ib_umad_port to 320 bytes
from 128.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up the errors as shown when 'let c_space_errors=1' is set in vim.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eliminate some padding in the structure by rearranging the members.
sizeof(struct ib_uverbs_event_file) is now 72 bytes (from 80) and
more members now fit in the first cacheline.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some large systems may support more than IB_UVERBS_MAX_DEVICES
(currently 32).
This change allows us to support more devices in a backwards-compatible
manner. The first IB_UVERBS_MAX_DEVICES keep the same major/minor
device numbers that they've always had.
If there are more than IB_UVERBS_MAX_DEVICES, we then dynamically
request a new major device number (new minors start at 0).
This change increases the maximum number of HCAs to 64 (from 32).
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but sets us up for a future change
that allows us to support more than IB_UVERBS_MAX_DEVICES in a system.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but it sets us up for a future
change that allows us to dynamically allocate device numbers in case
we have more than IB_UVERBS_MAX_DEVICES in the system.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dev_table's raison d'etre was to associate an inode back to a struct
ib_uverbs_device.
However, now that we've converted ib_uverbs_device to contain an
embedded cdev (instead of a *cdev), we can use the container_of()
macro and cast back to the containing device.
There's no longer any need for dev_table, so get rid of it.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Instead of storing a pointer to a cdev, embed the entire struct cdev.
This change allows us to use the container_of() macro in
ib_uverbs_open() in a future patch.
This change increases the size of struct ib_uverbs_device to 168 bytes
across 3 cachelines from 80 bytes in 2 cachelines. However, we
rearrange the members so that everything fits into the first cacheline
except for the struct cdev. Finally, we don't touch the cdev in any
fastpaths, so this change shouldn't negatively affect performance.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently the iSER receive completion flow takes the session lock
twice. Optimize it to avoid the first one by letting
iser_task_rdma_finalize() be called only from the cleanup_task
callback invoked by iscsi_free_task, thus reducing the contention on
the session lock between the scsi command submission to the scsi
command completion flows.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
libiscsi passthrough mode invokes the transport xmit calls directly
without first going through an internal queue, unlike the other mode,
which uses a queue and a xmitworker thread. Now that the "cant_sleep"
prerequisite of iscsi_host_alloc is met, move to use it. Handling
xmit errors is now done by the passthrough flow of libiscsi. Since
the queue/worker aren't used in this mode, the code that schedules the
xmitworker is removed.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove unnecessary checks for the IB connection state and for QP
overflow, as conn state changes are reported by iSER to libiscsi and
handled there. QP overflow is theoretically possible only when
unsolicited data-outs are used; anyway it's being checked and handled
by HW drivers.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Two minor flows in iSER's data path still use allocations; move them
to be atomic as a preperation step towards moving to use libiscsi
passthrough mode.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Simplify and shrink the logic/code used for the send descriptors.
Changes include removing struct iser_dto (an unnecessary abstraction),
using struct iser_regd_buf only for handling SCSI commands, using
dma_sync instead of dma_map/unmap, etc.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use a different CQ for send completions, where send completions are
polled by the interrupt-driven receive completion handler. Therefore,
interrupts aren't used for the send CQ.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that both the posting and reaping of receive buffers is done in
the completion path, the counter of outstanding buffers not be atomic.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently, the recv buffer posting logic is based on the transactional
nature of iSER which allows for posting a buffer before sending a PDU.
Change this to post only when the number of outstanding recv buffers
is below a water mark and in a batched manner, thus simplifying and
optimizing the data path. Use a pre-allocated ring of recv buffers
instead of allocating from kmem cache. A special treatment is given
to the login response buffer whose size must be 8K unlike the size of
buffers used for any other purpose which is 128 bytes.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We will make a major change in the recv buffer posting logic, after
which the problem commit bba7ebb "avoid recv buffer exhaustion caused
by unexpected PDUs" comes to solve doesn't exist any more, so revert it.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the nes driver to return -ENOMEM on SQ/RQ overflow to match the
return code of other RDMA HW drivers (e.g cxgb3, ehca, mlx4, mthca).
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Acked-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a double disconnect during AE processing, causing crashes.
While fixing the crash, also simplify the AE handling code.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a listener is destroyed and there is an MPA response pending for
loopback connection, the active side cm_node gets destroyed twice:
once in cm_event_connect_error() and again in nes_accept()/nes_reject().
Increment the cm_node's refcount so it's not destroyed by
cm_event_connect_error().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After running long iterative MPI tests, sometimes ethtool reports a
"CM Destroy Listener" count more than the "CM Create Listener" count.
This inconsistency is fixed by making counter variables atomic.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the caller does not pass a valid in_wc to process_mad(), return MAD
failure status, as it is not possible to generate a valid MAD redirect
response (and redirects are the only MAD responses ehca generates).
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Dunno, what was the idea, it wasn't used for a long time.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max_dest_rd_atomic and max_qp_rd_atomic values are properly
returned by query_qp(), so there should not be an error returned when
they are queried.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The irq_spinlock is only taken in tasklet context, so it is safe not to
disable hardware interrupts.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct ib_qp already holds a pointer to the ib device. No need to dive to the
hw device object to retrieve it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure compiler won't do weird things with limits by using the
rlimit helpers added in 3e10e716 ("resource: add helpers for fetching
rlimits"). E.g. fetching them twice may return 2 different values
after writable limits are implemented.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As of commit f56bcd8 ("IPoIB: Use separate CQ for UD send
completions"), there are no TX interrupts. Change the ethtool code
not to report TX moderation settings, so users will not be misled to
think they can control TX interrupt moderation. Pointed out by Alex
Vainman <alexv@voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Failure to rearm a CQ means the cxgb3 device is wedged, but we shouldn't
kill the whole system with a BUG_ON() if this happens.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cm: Revert association of an RDMA device when binding to loopback
Revert the following change from commit 6f8372b6 ("RDMA/cm: fix
loopback address support")
The defined behavior of rdma_bind_addr is to associate an RDMA
device with an rdma_cm_id, as long as the user specified a non-
zero address. (ie they weren't just trying to reserve a port)
Currently, if the loopback address is passed to rdma_bind_addr,
no device is associated with the rdma_cm_id. Fix this.
It turns out that important apps such as Open MPI depend on
rdma_bind_addr() NOT associating any RDMA device when binding to a
loopback address. Open MPI is being updated to deal with this, but at
least until a new Open MPI release is available, maintain the previous
behavior: allow rdma_bind_addr() to succeed, but do not bind to a
device.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct misspelled "CONFIG_IPv6" that was introduced in commit
d14714df ("IB/addr: Fix IPv6 routing lookup"). The config variable
should be all uppercase.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[ This was my fault when I munged the original patch. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mlx4_ib_post_recv(), we should check the queue for overflow using
recv_cq instead of send_cq (current code looks like a copy-and-paste
mistake).
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As for memfree mthca hardware, ConnectX also requires SRQ WQE scatter
entries to be initialized with the invalid L_Key at SRQ creation time.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the "ignoring return value of '...', declared with attribute
warn_unused_result" compiler warning in several users of the new kfifo
API.
It removes the __must_check attribute from kfifo_in() and
kfifo_in_locked() which must not necessary performed.
Fix the allocation bug in the nozomi driver file, by moving out the
kfifo_alloc from the interrupt handler into the probe function.
Fix the kfifo_out() and kfifo_out_locked() users to handle a unexpected
end of fifo.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rename kfifo_put... into kfifo_in... to prevent miss use of old non in
kernel-tree drivers
ditto for kfifo_get... -> kfifo_out...
Improve the prototypes of kfifo_in and kfifo_out to make the kerneldoc
annotations more readable.
Add mini "howto porting to the new API" in kfifo.h
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the pointer to the spinlock out of struct kfifo. Most users in
tree do not actually use a spinlock, so the few exceptions now have to
call kfifo_{get,put}_locked, which takes an extra argument to a
spinlock.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new generic kernel FIFO implementation.
The current kernel fifo API is not very widely used, because it has to
many constrains. Only 17 files in the current 2.6.31-rc5 used it.
FIFO's are like list's a very basic thing and a kfifo API which handles
the most use case would save a lot of development time and memory
resources.
I think this are the reasons why kfifo is not in use:
- The API is to simple, important functions are missing
- A fifo can be only allocated dynamically
- There is a requirement of a spinlock whether you need it or not
- There is no support for data records inside a fifo
So I decided to extend the kfifo in a more generic way without blowing up
the API to much. The new API has the following benefits:
- Generic usage: For kernel internal use and/or device driver.
- Provide an API for the most use case.
- Slim API: The whole API provides 25 functions.
- Linux style habit.
- DECLARE_KFIFO, DEFINE_KFIFO and INIT_KFIFO Macros
- Direct copy_to_user from the fifo and copy_from_user into the fifo.
- The kfifo itself is an in place member of the using data structure, this save an
indirection access and does not waste the kernel allocator.
- Lockless access: if only one reader and one writer is active on the fifo,
which is the common use case, no additional locking is necessary.
- Remove spinlock - give the user the freedom of choice what kind of locking to use if
one is required.
- Ability to handle records. Three type of records are supported:
- Variable length records between 0-255 bytes, with a record size
field of 1 bytes.
- Variable length records between 0-65535 bytes, with a record size
field of 2 bytes.
- Fixed size records, which no record size field.
- Preserve memory resource.
- Performance!
- Easy to use!
This patch:
Since most users want to have the kfifo as part of another object,
reorganize the code to allow including struct kfifo in another data
structure. This requires changing the kfifo_alloc and kfifo_init
prototypes so that we pass an existing kfifo pointer into them. This
patch changes the implementation and all existing users.
[akpm@linux-foundation.org: fix warning]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (38 commits)
direct I/O fallback sync simplification
ocfs: stop using do_sync_mapping_range
cleanup blockdev_direct_IO locking
make generic_acl slightly more generic
sanitize xattr handler prototypes
libfs: move EXPORT_SYMBOL for d_alloc_name
vfs: force reval of target when following LAST_BIND symlinks (try #7)
ima: limit imbalance msg
Untangling ima mess, part 3: kill dead code in ima
Untangling ima mess, part 2: deal with counters
Untangling ima mess, part 1: alloc_file()
O_TRUNC open shouldn't fail after file truncation
ima: call ima_inode_free ima_inode_free
IMA: clean up the IMA counts updating code
ima: only insert at inode creation time
ima: valid return code from ima_inode_alloc
fs: move get_empty_filp() deffinition to internal.h
Sanitize exec_permission_lite()
Kill cached_lookup() and real_lookup()
Kill path_lookup_open()
...
Trivial conflicts in fs/direct-io.c
Always set bad_wr when an immediate error is detected. Return ENOMEM
for queue full instead of EINVAL to match other drivers.
Signed-off-by: Frank Zago <fzago@systemfabricworks.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
When the remote node's ethernet address changes, the connection keeps
trying to connect using the old address. The connection wil continue
failing until the driver is unloaded and loaded again (eiter reboot or
rmmod). Fix this by checking that the NIC has the correct address
before starting a connection.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A FIN that is received during an MPA start up sequence causes a
timeout in iwcm.c. The connection has not been completely closed so
the iwcm code is waiting for resources to be cleaned up. This closes
the connection so everything cleans up correctly.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We fail when creating many qps as kmap() fails for sq_vbase.
Fix this by doing kunmap() as soon as we are done with sq_vbase.
We do kunmap() in one of the locations below:
(1) nes_destroy_qp()
(2) nes_accept()
(3) nes_connect_event
We keep a flag to avoid multiple calls to kunmap().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
STags are generated randomly but the driver does not correctly prevent
a zero STag. Using STag zero is privileged and causes a user space
application to fail. This change prevents the driver from trying to
allocate a zero STag.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
While running a Xansation test, an active side node crashed. The
problem started on the passive side, which generated an STtag that was
0. The passive side sent a TERMINATE instead of an MPA REJECT msg.
The active side, receives TERMINATE and sends connect_err() and set
the cm_node state to CLOSED. The passive side sends FIN + ACK after
TERMINATE. Active side ends up in handle_ack_pkt() and send_reset().
send_reset() consumes 1 cm_node's ref_count. Because the cm_node is
in CLOSED state, which means that cm_node will be destroyed after
completion of the connect_err() indication, CM will crash after
send_reset().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the listener is destroyed for a loopback connection, the listener
node gets a reset event. This causes a crash as the listener is not
expecting a reset event. Code review of cm_event_reset() during
debugging showed the cm_id ref count is incremented after calling its
event handler and not before.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
While running IMP_EXT's window test, we saw a crash in nes_accept().
Here is the sequence of what happened:
(1) In MVAPICH2, connect request is received for port #0.
FIX: Add a nes_connect() check to make sure local or remote tcp port
is not 0.
(2) Remote node's (passive) TCP stack sends a reset when it gets a
connect request because of port = 0. Active side set the connect
error to IW_CM_EVENT_STATUS_REJECTED when it received the RST from
remote node.
FIX: The corect error code is -ECONNRESET.
(3) Wrong error code of IW_CM_EVENT_STATUS_REJECTED causes the core to
destroy its listener ports. Here there are connections that may
have sent an MPA request up and waiting for accept or reject. But
the listener and its cm_nodes have been freed already causing the
crash noticed.
FIX: The cm_node is freed only if its state is not
NES_CM_STATE_MPAREQ_RCVD. If cm_node's state is
NES_CM_STATE_MPAREQ_RCVD then its new state is set to
NES_CM_STATE_LISTENER_DESTROYED and it is not freed. When
nes_accept() or nes_reject() is received, its state is checked
for NES_CM_STATE_LISTENER_DESTROYED and in this case the cm_node
is freed and error is returned.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During testing of REJECT connection error handling, we saw that the
cm_id resources are not released. When the retransmit timer expires,
we need to send a reset message to remote node before issuing the
ABORTED event.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During Xansation testing, we saw that error handling of MPA frame
msg/response is not handled properly.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ORD size needs updating as we are supporting more inbound READ
resources per connection.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change MAX_CM_BUFFER for MPA frames to be conformant to RFC 5044:
we need 512 + 20 instead of 512.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The size argument to ioremap_nocache should be the size of desired
information, not the pointer to it.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@expression@
expression *x;
@@
x =
<+...
*sizeof(x)
...+>// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update copyright from Intel-NE, Inc. to Intel Corporation. Use proper
branding string in Kconfig and simplify description.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a check to nes_create_cq() to return -EINVAL if creating a CQ with
depth > max_cqe (32766).
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add IB_SINGAL_ALL_WR support as an iWARP extension. If set, make sure
all WR for the QP are signalled. Consolidate flags used in nesqp
structure.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add additional PHY uC status check in case PHY firmware is not running
properly with heartbeat. Add a hard PHY reset if uC status is 0x0
after initial reset.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Always set bad_wr when an immediate error is detected. Do not report
success if an error occurred.
Signed-off-by: Frank Zago <fzago@systemfabricworks.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Always set bad_wr when an immediate error is detected.
Signed-off-by: Frank Zago <fzago@systemfabricworks.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IB_WR_SEND_WITH_INV, IB_WR_RDMA_READ_WITH_INV
and IB_WR_LOCAL_INV.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On error, set bad_wr in nes_post_recv(). Stop processing ib_wr queue
when an error is detected.
Signed-off-by: Frank Zago <fzago@systemfabricworks.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On error, set bad_wr in nes_post_send(). Stop processing ib_wr queue
when an error is detected.
Signed-off-by: Frank Zago <fzago@systemfabricworks.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ibmebus_free_irq() function, which might sleep, was called with
interrupts disabled. To fix this, make sure that no interrupts are
running by killing the interrupt tasklet. Also lock the
shca_list_lock to protect against the poll_eqs_timer running
concurrently.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use bitmap_weight() instead of finding all set bits in bitmap by hand.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Ralph Campbell <infinipath@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB can miss a change in destination GID under some conditions. The
problem is caused when ipoib_neigh->dgid contains a stale address.
The fix is to set ipoib_neigh->dgid to zero in ipoib_neigh_alloc().
This can happen when a system using bonding on its IPoIB interfaces
has switched its active interface from interface A to B and back to A.
The system that fails over will not correctly processes the 2nd
address change, as described below.
When an address has changed neighbor->ha is updated with the new
address. Each neighbor has an associated ipoib_neigh.
ipoib_neigh->dgid also holds a copy of the remote node's hardware
address. When an address changes neighbor->ha is updated by the
network layer (arp code) with the new address. IPoIB detects this
change in ipoib_start_xmit() by comparing neighbor->ha with
ipoib_neigh->dgid. The bug is that ipoib_neigh->dgid may already
contain the new address (A) thus the change from B to A is missed by
ipoib. Here is the sequence of events:
ipoib_neigh->dgid = A and neighbor->ha = A
The address is switched to B (the first switch)
neighbor->ha = B
The change is seen in ipoib_start_xmit() -- neighbor->ha !=
ipoib_neigh->dgid so ipoib_neigh is released, and a new one is
allocated.
The allocator may return the same chunk of memory that was just
released, therefore ipoib_neigh->dgid still contains A at this point.
ipoib_neigh->dgid should be updated in neigh_add_path(), but if the
following conditions are true dgid is not updated:
1) __path_find() returns a path
2) path->ah is NULL
The remote system now switches from address B to A, neighbor->ha is
updated to A.
Now we have again : ipoib_neigh->dgid = A and neighbor->ha = A
Since the addresses are the same ipoib won't process the change in
address. Fix this by zeroing out the dgid field when allocating a new
struct ipoib_neigh.
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'bkl-drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
agp: Remove the BKL from agp_open
inifiband: Remove BKL from ipath_open()
mips: Remove BKL from tb0219
drivers: Remove BKL from scx200_gpio
drivers: Remove BKL from pc8736x_gpio
parisc: Remove BKL from eisa_eeprom
rtc: Remove BKL from efirtc
input: Remove BKL from hp_sdc_rtc
hw_random: Remove BKL from core
macintosh: Remove BKL from ans-lcd
nvram: Drop the bkl from non-generic nvram_llseek()
nvram: Drop the bkl from nvram_llseek()
mem_class: Drop the bkl from memory_open()
spi: Remove BKL from spidev_open
drivers: Remove BKL from cs5535_gpio
drivers: Remove BKL from misc_open
When iser enabled lu reset support it did not set the
bit to allow userspace to get/set the timeout. This
sets the tgt and lu reset timeout bits.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fix some typos and punctuation in comments
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Include link scope as part of address resolution. Combine local
and remote address resolution into a single, simpler code path.
Fix error checking in the IPv6 routing lookups.
Based on work from:
David Wilder <dwilder@us.ibm.com>
Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
[ Fix up cma_check_linklocal() for !IPV6 case. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Merge resolve local/remote address resolution into a single
data flow to ensure consistent access and use of the local routing
tables.
Based on work from:
David Wilder <dwilder@us.ibm.com>
Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The RDMA CM is intended to support the use of a loopback address
when establishing a connection; however, the behavior of the CM
when loopback addresses are used is confusing and does not always
work, depending on whether loopback was specified by the server,
the client, or both.
The defined behavior of rdma_bind_addr is to associate an RDMA
device with an rdma_cm_id, as long as the user specified a non-
zero address. (ie they weren't just trying to reserve a port)
Currently, if the loopback address is passed to rdam_bind_addr,
no device is associated with the rdma_cm_id. Fix this.
If a loopback address is specified by the client as the destination
address for a connection, it will fail to establish a connection.
This is true even if the server is listing across all addresses or
on the loopback address itself. The issue is that the server tries
to translate the IP address carried in the REQ message to a local
net_device address, which fails. The translation is not needed in
this case, since the REQ carries the actual HW address that should
be used.
Finally, cleanup loopback support to be more transport neutral.
Replace separate calls to get/set the sgid and dgid from the
device address to a single call that behaves correctly depending
on the format of the device address. And support both IPv4 and
IPv6 address formats.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
[ Fixed RDS build by s/ib_addr_get/rdma_addr_get/ - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct rdma_dev_addr stores net_device address information:
the source device address, destination hardware address, and
broadcast address. For consistency, store the net_device type
rather than converting it to the rdma_node_type.
The type indicates the format of the various hardware addresses,
which is what we're concerned with, and not the RDMA node type
that the address may map to.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a source address is provided, verify that the address family matches
that of the destination address. If the source is not specified, use the
same address family as the destination.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Provide the device interface when resolving route information to
ensure that the correct outbound device is used. This will also
simplify processing of sin6_scope_id for IPv6 support.
Based on work from:
David Wilder <dwilder@us.ibm.com>
Jason Gunthorpe <jgunthrope@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If joining to an AF_INET6 address, we need to map the address to a MGID
in the same way as the IP stack. The old code would just fall through to
the IPv4 case and generate garbage.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
RDMA CM treats AF_INET6 addresses that are either 0 or prefixed with
FF1x:A01B::/32 as MGIDs, but the detection for the prefix was buggy;
fix it up.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
for_each_netdev() should be used with RTNL or dev_base_lock held,
or else we risk a crash.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export rdma_set_ib_paths to user space to allow applications to
manually set the IB path used for connections. This allows
alternative ways for a user space application or library to obtain
path record information, including retrieving path information
from cached data, avoiding direct interaction with the IB SA.
The IB SA is a single, centralized entity that can limit scaling
on large clusters running MPI applications.
Future changes to the rdma cm can expand on this framework to
support the full range of features allowed by the IB CM, such as
separate forward and reverse paths and APM.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After dma-mapping an SG list provided by the SCSI midlayer, iser has
to make sure the mapped SG is "aligned for RDMA" in the sense that its
possible to produce one mapping in the HCA IOMMU which represents the
whole SG. Next, the mapped SG is formatted for registration with the HCA.
This patch re-writes the logic that does the above, to make it clearer
and simpler. It also fixes a bug in the being aligned for RDMA checks,
where a "start" check wasn't done but rather only "end" check.
Signed-off-by: Alexander Nezhinsky <alexandern@voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current code has a limitation: an LSO header is not allowed to cross a
64 byte boundary. This patch removes this limitation by setting the
WQE RR for large headers thus allowing LSO headers of any size. The
extra buffer reserved for MLX4_IB_QP_LSO QPs has been doubled, from 64
to 128 bytes, assuming this is reasonable upper limit for header
length. Also, this patch will cause IB_DEVICE_UD_TSO to be set only
for HCA FW versions that set MLX4_DEV_CAP_FLAG_BLH; e.g. FW version
2.6.000 and higher.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is no such flag DE - the field is reserved and should be zero.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch was generated by
git grep -E -i -l '[Aa]quire' | xargs -r perl -p -i -e 's/([Aa])quire/$1cquire/'
and the cumsumed was found by checking the diff for aquire.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
cycle_kernel_lock() got pushed down to ipath_open(). I tried hard to
understand what it might protect, but finally gave up.
Roland noted that qlogic seems to have abandoned the ipath driver and
came to the following wise conclusion: "So I guess if the BKL stuff is
blocking you in any way, we can just drop it from ipath and leave it
as yet another race condition in a rotting old driver."
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <adad44tj090.fsf@cisco.com>
Cc: Roland Dreier <rdreier@cisco.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (34 commits)
[SCSI] qla2xxx: Fix NULL ptr deref bug in fail path during queue create
[SCSI] st: fix possible memory use after free after MTSETBLK ioctl
[SCSI] be2iscsi: Moving to pci_pools v3
[SCSI] libiscsi: iscsi_session_setup to allow for private space
[SCSI] be2iscsi: add 10Gbps iSCSI - BladeEngine 2 driver
[SCSI] zfcp: Fix hang when offlining device with offline chpid
[SCSI] zfcp: Fix lockdep warning when offlining device with offline chpid
[SCSI] zfcp: Fix oops during shutdown of offline device
[SCSI] zfcp: Fix initial device and cfdc for delayed adapter allocation
[SCSI] zfcp: correctly initialize unchained requests
[SCSI] mpt2sas: Bump version 02.100.03.00
[SCSI] mpt2sas: Support dev remove when phy status is MPI2_EVENT_SAS_TOPO_PHYSTATUS_VACANT
[SCSI] mpt2sas: Timeout occurred within the HANDSHAKE logic while waiting on firmware to ACK.
[SCSI] mpt2sas: Call init_completion on a per request basis.
[SCSI] mpt2sas: Target Reset will be issued from Interrupt context.
[SCSI] mpt2sas: Added SCSIIO, Internal and high priority memory pools to support multiple TM
[SCSI] mpt2sas: Copyright change to 2009.
[SCSI] mpt2sas: Added mpi2_history.txt for MPI2 headers.
[SCSI] mpt2sas: Update driver to MPI2 REV K headers.
[SCSI] bfa: Brocade BFA FC SCSI driver
...
This patch allows a local IPv6 address to be resolved by rdma_cm.
To reproduce the problem:
$ rping -s -v -a ::0 &
$ rping -c -v -a <IPv6 address local to this system>
rdma_resolve_addr error -1
Local IPv6 address was obtained with "ip addr show ib0"
Addresses: https://bugs.openfabrics.org/show_bug.cgi?id=1759
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
in_dev_get() can return NULL. If it does, iwch_query_port() will crash.
Handle the NULL case by mapping it to port state INIT.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In commit cb58160e ("RDMA/iwcm: Reject the connection when the cm_id
is destroyed") a call to the provider's reject handler was added to
destroy_cm_id() to fix a provider endpoint leak. This call needs to
be done with interrupts enabled. So unlock and relock around this
call. This is safe because:
1) the provider will do nothing with this endpoint until the iwcm either
accepts or rejects.
2) the lock is only released after the iwcm state is changed, so an
errant iwcm app that is destroying -and- rejecting the connection
concurrently will get a failure on one of the calls.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
These string query operations were supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert the remaining
implementations.
Also remove calls to these operations to initialise drvinfo->n_stats.
The ethtool core code already does that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use this_cpu_ptr and __this_cpu_ptr in locations where straight
transformations are possible because per_cpu_ptr is used with
either smp_processor_id() or raw_smp_processor_id().
cc: David Howells <dhowells@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
cc: Ingo Molnar <mingo@elte.hu>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch contains changes that allow iscsi_session_setup
to allocate private space for LLD's
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Don't turn on carrier for a non-active port
IB/mthca: Fix access to freed memory in catastrophic event handling
mlx4_core: Pass cache line size to device FW
RDMA/nes: Remove duplicate .ndo_set_mac_address field initialization
IB/mad: Fix lock-lock-timer deadlock in RMPP code
Multicast joins can succeed even if the IB port is down. This happens
when the SM runs on the same port with the requesting port. However,
IPoIB calls netif_carrier_on() when the join of the broadcast group
succeeds, without caring about the state of the IB port. The result
is an IPoIB interface in RUNNING state but without an active IB port
to support it.
If a bonding interface uses this IPoIB interface as a slave it might
not detect that this slave is almost useless and failover
functionality will be damaged. The fix checks the state of the IB
port in the carrier_task before calling netif_carrier_on().
Adresses: https://bugs.openfabrics.org/show_bug.cgi?id=1726
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
catas_reset() uses a pointer to mthca_dev, but mthca_dev is not valid
after the call to __mthca_restart_one().
Based on a similar patch for mlx4 (634354d7, "mlx4: Fix access to
freed memory") by Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The definition of nes_netdev_ops has initializations of a local function
and eth_mac_addr for its ndo_set_mac_address field. This change uses only
the local function.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@
if int(ps[0].line)!=int(pr[0].line) or int(ps[0].column)!=int(pr[0].column):
cocci.print_main(fld,p0)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Holding agent->lock across cancel_delayed_work() (which does
del_timer_sync()) in ib_cancel_rmpp_recvs() leads to lockdep reports of
possible lock-timer deadlocks if a consumer ever does something that
connects agent->lock to a lock taken in IRQ context (cf
http://marc.info/?l=linux-rdma&m=125243699026045).
Fix this by changing the list items to a new state "CANCELING" while
holding the lock, and then canceling the delayed work without holding
the lock. If the delayed work runs after the lock is dropped, it will
see the state is CANCELING and return immediately, so the list will
stay stable while we traverse it with the lock not held.
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
If the cm_id of a connect request is destroyed prior to the ULP
accepting or rejecting the connection, then the provider never cleans
up the connection. The iwcm should explicitly reject these
connections if the cm_id is destroyed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
FW mismatches can cause a crash in the iw_cxgb3 event handler.
- NULL the t3cdev->ulp pointer on failures in cxio_rdev_open()
- Silently ignore events when the ulp ptr is NULL in iwch_err_handler()
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
MADs are UD and can be dropped if there are no receives posted, so
allow receive queue size to be set with a module parameter in case the
queue needs to be lengthened. Send side tuning is done for symmetry
with receive.
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Lockdep reported a possible deadlock with cm_id_priv->lock,
mad_agent_priv->lock and mad_agent_priv->timed_work.timer; this
happens because the mad module does
cancel_delayed_work(&mad_agent_priv->timed_work);
while holding mad_agent_priv->lock. cancel_delayed_work() internally
does del_timer_sync(&mad_agent_priv->timed_work.timer).
This can turn into a deadlock because mad_agent_priv->lock is taken
inside cm_id_priv->lock, so we can get the following set of contexts
that deadlock each other:
A: holding cm_id_priv->lock, waiting for mad_agent_priv->lock
B: holding mad_agent_priv->lock, waiting for del_timer_sync()
C: interrupt during mad_agent_priv->timed_work.timer that takes
cm_id_priv->lock
Fix this by using the new __cancel_delayed_work() interface (which
internally does del_timer() instead of del_timer_sync()) in all the
places where we are holding a lock.
Addresses: http://bugzilla.kernel.org/show_bug.cgi?id=13757
Reported-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Old query_port code reports static MTU and link state values.
Instead, map actual MTU to next largest IB_MTU_* constant and
correctly report link state.
Cc: Steve Wise <swise@opengridcomputing.com>
Reported-by: Jeff Squyres <jsquyres@cisco.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The disconn routine has been reworked to acoomodate the terminate and
flushing changes. The routine has been reorganized to make all the
decisions at the start then it performs all the required operations.
This simplified the lock handling and is easier to follow.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the flush status to fill in cqe status when a specific error has
been identified. Subsequent flushed completions still use the flushed
value.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a flush request is given to the hw, it will place one cqe marked
as flushed (unless there is nothing to flush). An application that is
waiting for all wqe's to complete will be left hanging. This modifies
poll_cq to return the correct number of flushes for the pending
elements on the wq.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When an asynchronous event occurs that requires a terminate, it is
sometimes possible to identify the wqe in error. This change uses
flush to get this information to the poll routine. The flush
operation puts the status into the cqe. If this information is not
available, it continues to use the more generic flush code as before.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement the sending and receiving of Terminate packets.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
CQ errors are not being handled correctly. Put in the the upcall for
CQ errors.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a QP is destroyed, unprocessed CQ entries could still reference
the QP. This change zeroes the context value at QP destroy time. By
skipping over cqe's with a zero context, poll_cq no longer processes a
cqe for a destroyed QP.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The routine to allocate a cqp request is not called from process
context code. Since it is not OK to sleep, it needs to use GFP_ATOMIC
not GFP_KERNEL.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code currently has a work structure in the QP. This requires a
lock and a pending flag to ensure there is never more than one request
active. When two events happen quickly (such as FIN and LLP CLOSE),
it causes unnecessary timeouts since the second one is dropped.
This fix allocates memory for the work request so the second one can
be queued. A lock is removed since it is no longer needed.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During termination, it is possible for the refcnt to go to zero while
the worker thread is posting events upward. This fix increments the
refcnt before the request is passed to the worker thread. The thread
decrements the refcnt when the request is completed.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace apps are supposed to release all ib device resources if they
receive a fatal async event (IBV_EVENT_DEVICE_FATAL). However, the
app has no way of knowing when the device has come back up, except to
repeatedly attempt ibv_open_device() until it succeeds.
However, currently there is no protection against the open succeeding
while the device is in being removed following the fatal event. In
this case, the open will succeed, but as a result the device waits in
the middle of its removal until the new app releases its resources --
and the new app will not do so, since the open succeeded at a point
following the fatal event generation.
This patch adds an "active" flag to the device. The active flag is set
to false (in the fatal event flow) before the "fatal" event is
generated, so any subsequent ibv_dev_open() call to the device will
fail until the device comes back up, thus preventing the above
deadlock.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the mthca driver uses the same name for interrupts for every
device in the system. This can make it very confusing trying to work
out exactly which device MSI-X interrupts are for. Change the driver
to add the PCI name of the device to the interrupt name.
Signed-off-by: Arputham Benjamin <abenjamin@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_ib_lock_cqs()/mthca_ib_unlock_cqs() are helper functions that
lock/unlock both CQs attached to a QP in the proper order to avoid
AB-BA deadlocks. Annotate this so sparse can understand what's going
on (and warn us if we misuse these functions).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_config_reg.h was including <asm/page.h> for no reason -- the whole
file is just defines of constants, so it's entirely self-contained.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace apps are supposed to release all ib device resources if they
receive a fatal async event (IBV_EVENT_DEVICE_FATAL). However, the
app has no way of knowing when the device has come back up, except to
repeatedly attempt ibv_open_device() until it succeeds.
However, currently there is no protection against the open succeeding
while the device is in being removed following the fatal event. In
this case, the open will succeed, but as a result the device waits in
the middle of its removal until the new app releases its resources --
and the new app will not do so, since the open succeeded at a point
following the fatal event generation.
This patch adds an "active" flag to the device. The active flag is set
to false (in the fatal event flow) before the "fatal" event is
generated, so any subsequent ibv_dev_open() call to the device will
fail until the device comes back up, thus preventing the above
deadlock.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_ib_lock_cqs()/mlx4_ib_unlock_cqs() are helper functions that
lock/unlock both CQs attached to a QP in the proper order to avoid
AB-BA deadlocks. Annotate this so sparse can understand what's going
on (and warn us if we misuse these functions).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dev->ibdev.iwcm allocation may fail, prevent a dereference.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since the original commit 883a99c7 ("[IB] uverbs: Add a mask of device
methods allowed for userspace"), the uverbs core returns EINVAL for
commands not implemented by a specific low-level driver.
This creates a problem that there is no way to tell the difference
between an unimplemented command and an implemented one which is
incorrectly invoked (which also returns EINVAL).
The fix is to have unimplemented commands return ENOSYS.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Until now, retries were only sent when joining a multicast group. This
patch will adds retries when leaving a multicast group as well.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace open-coded reimplementations with printk_once().
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the %pM conversion specifier to print a MAC address.
Signed-off-by: Tobias Klauser <klto@zhaw.ch>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than just defining static spinlock_t variables and then
initializing them later in init functions, simply define them with
DEFINE_SPINLOCK() and remove the calls to spin_lock_init(). This cleans
up the source a tad and also shrinks the compiled code; eg on x86-64:
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-40 (-40)
function old new delta
ib_uverbs_init 336 326 -10
ib_mad_init_module 147 137 -10
ib_sa_init 123 103 -20
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hop count field in a directed route MAD is only allowed to be in the
range 0 to 63 (by spec). Check that this really is the case to avoid
accessing outside the bounds of the hop array.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check that the format of multicast link addresses is correct before
taking them from dev->mc_list to priv->multicast_list. This way we
never try to send a bogus address to the SA, which prevents badness
from erronous 'ip maddr addr add', broken bonding drivers, etc.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB currently must use irqsave locking for priv->lock, since it is
taken from interrupt context in one path. However, ipoib_send() does
skb_orphan(), and the network stack locking is not IRQ-safe.
Therefore we need to make sure we don't hold priv->lock when calling
ipoib_send() to avoid lockdep warnings (the code was almost certainly
safe in practice, since the only code path that takes priv->lock from
interrupt context would never call into the network stack).
Addresses: http://bugzilla.kernel.org/show_bug.cgi?id=13757
Reported-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>