Function netif_schedule_queue() has a hardcoded comparison between queue
state and any xoff flag. This comparison does the same thing as method
netif_xmit_stopped(). In terms of code clarity, it is better. See other
methods like: generic_xdp_tx() and dev_direct_xmit().
Signed-off-by: Julio Faracco <jcfaracco@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a 3rd extension, add a new helper that drops the
extension space and use it when we need to scrub an sk_buff.
At this time, scrubbing clears secpath and bridge netfilter data, but
retains the tc skb extension, after this patch all three get cleared.
NAPI reuse/free assumes we can only have a secpath attached to skb, but
it seems better to clear all extensions there as well.
v2: add unlikely hint (Eric Dumazet)
Fixes: 95a7233c45 ("net: openvswitch: Set OvS recirc_id from tc chain index")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test implemented by some_qdisc_is_busy() is somewhat loosy for
NOLOCK qdisc, as we may hit the following scenario:
CPU1 CPU2
// in net_tx_action()
clear_bit(__QDISC_STATE_SCHED...);
// in some_qdisc_is_busy()
val = (qdisc_is_running(q) ||
test_bit(__QDISC_STATE_SCHED,
&q->state));
// here val is 0 but...
qdisc_run(q)
// ... CPU1 is going to run the qdisc next
As a conseguence qdisc_run() in net_tx_action() can race with qdisc_reset()
in dev_qdisc_reset(). Such race is not possible for !NOLOCK qdisc as
both the above bit operations are under the root qdisc lock().
After commit 021a17ed79 ("pfifo_fast: drop unneeded additional lock on dequeue")
the race can cause use after free and/or null ptr dereference, but the root
cause is likely older.
This patch addresses the issue explicitly checking for deactivation under
the seqlock for NOLOCK qdisc, so that the qdisc_run() in the critical
scenario becomes a no-op.
Note that the enqueue() op can still execute concurrently with dev_qdisc_reset(),
but that is safe due to the skb_array() locking, and we can't avoid that
for NOLOCK qdiscs.
Fixes: 021a17ed79 ("pfifo_fast: drop unneeded additional lock on dequeue")
Reported-by: Li Shuang <shuali@redhat.com>
Reported-and-tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In event of failure during register_netdevice, free_netdev is
invoked immediately. free_netdev assumes that all the netdevice
refcounts have been dropped prior to it being called and as a
result frees and clears out the refcount pointer.
However, this is not necessarily true as some of the operations
in the NETDEV_UNREGISTER notifier handlers queue RCU callbacks for
invocation after a grace period. The IPv4 callback in_dev_rcu_put
tries to access the refcount after free_netdev is called which
leads to a null de-reference-
44837.761523: <6> Unable to handle kernel paging request at
virtual address 0000004a88287000
44837.761651: <2> pc : in_dev_finish_destroy+0x4c/0xc8
44837.761654: <2> lr : in_dev_finish_destroy+0x2c/0xc8
44837.762393: <2> Call trace:
44837.762398: <2> in_dev_finish_destroy+0x4c/0xc8
44837.762404: <2> in_dev_rcu_put+0x24/0x30
44837.762412: <2> rcu_nocb_kthread+0x43c/0x468
44837.762418: <2> kthread+0x118/0x128
44837.762424: <2> ret_from_fork+0x10/0x1c
Fix this by waiting for the completion of the call_rcu() in
case of register_netdevice errors.
Fixes: 93ee31f14f ("[NET]: Fix free_netdev on register_netdev failure.")
Cc: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't uninstall an XDP program when none is installed, and don't install
an XDP program that has the same ID as the one already installed.
dev_change_xdp_fd doesn't perform any checks in case it uninstalls an
XDP program. It means that the driver's ndo_bpf can be called with
XDP_SETUP_PROG asking to set it to NULL even if it's already NULL. This
case happens if the user runs `ip link set eth0 xdp off` when there is
no XDP program attached.
The symmetrical case is possible when the user tries to set the program
that is already set.
The drivers typically perform some heavy operations on XDP_SETUP_PROG,
so they all have to handle these cases internally to return early if
they happen. This patch puts this check into the kernel code, so that
all drivers will benefit from it.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When GRO decides not to coalesce a packet, in napi_frags_finish(), instead
of passing it to the stack immediately, place it on a list in the napi
struct. Then, at flush time (napi_complete_done(), napi_poll(), or
napi_busy_loop()), call netif_receive_skb_list_internal() on the list.
We'd like to do that in napi_gro_flush(), but it's not called if
!napi->gro_bitmask, so we have to do it in the callers instead. (There are
a handful of drivers that call napi_gro_flush() themselves, but it's not
clear why, or whether this will affect them.)
Because a full 64 packets is an inefficiently large batch, also consume the
list whenever it exceeds gro_normal_batch, a new net/core sysctl that
defaults to 8.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When generic-XDP was moved to a later processing step by commit
458bf2f224 ("net: core: support XDP generic on stacked devices.")
a regression was introduced when using bpf_xdp_adjust_head.
The issue is that after this commit the skb->network_header is now
changed prior to calling generic XDP and not after. Thus, if the header
is changed by XDP (via bpf_xdp_adjust_head), then skb->network_header
also need to be updated again. Fix by calling skb_reset_network_header().
Fixes: 458bf2f224 ("net: core: support XDP generic on stacked devices.")
Reported-by: Brandon Cazander <brandon.cazander@multapplied.net>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_warn_bad_offload and netdev_rx_csum_fault trigger on hard to debug
issues. Dump more state and the header.
Optionally dump the entire packet and linear segment. This is required
to debug checksum bugs that may include bytes past skb_tail_pointer().
Both call sites call this function inside a net_ratelimit() block.
Limit full packet log further to a hard limit of can_dump_full (5).
Based on an earlier patch by Cong Wang, see link below.
Changes v1 -> v2
- dump frag_list only on full_pkt
Link: https://patchwork.ozlabs.org/patch/1000841/
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TC_ACT_REINSERT return type was added as an in-kernel only option to
allow a packet ingress or egress redirect. This is used to avoid
unnecessary skb clones in situations where they are not required. If a TC
hook returns this code then the packet is 'reinserted' and no skb consume
is carried out as no clone took place.
This return type is only used in act_mirred. Rather than have the reinsert
called from the main datapath, call it directly in act_mirred. Instead of
returning TC_ACT_REINSERT, change the type to the new TC_ACT_CONSUMED
which tells the caller that the packet has been stolen by another process
and that no consume call is required.
Moving all redirect calls to the act_mirred code is in preparation for
tracking recursion created by act_mirred.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stack receives pkt: [802.1P vlan 0][802.1AD vlan 100][IPv4],
vlan_do_receive() returns false if it does not find vlan_dev. Later
__netif_receive_skb_core() fails to find packet type handler for
skb->protocol 801.1AD and drops the packet.
801.1P header with vlan id 0 should be handled as untagged packets.
This patch fixes it by checking if vlan_id is 0 and processes next vlan
header.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.
2) Read SFP eeprom in max 16 byte increments to avoid problems with
some SFP modules, from Russell King.
3) Fix UDP socket lookup wrt. VRF, from Tim Beale.
4) Handle route invalidation properly in s390 qeth driver, from Julian
Wiedmann.
5) Memory leak on unload in RDS, from Zhu Yanjun.
6) sctp_process_init leak, from Neil HOrman.
7) Fix fib_rules rule insertion semantic change that broke Android,
from Hangbin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
net: aquantia: fix wol configuration not applied sometimes
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
net: rds: fix memory leak when unload rds_rdma
ipv6: fix the check before getting the cookie in rt6_get_cookie
ipv4: not do cache for local delivery if bc_forwarding is enabled
s390/qeth: handle error when updating TX queue count
s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
s390/qeth: check dst entry before use
s390/qeth: handle limited IPv4 broadcast in L3 TX path
net: fix indirect calls helpers for ptype list hooks.
net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
udp: only choose unbound UDP socket for multicast when not in a VRF
net/tls: replace the sleeping lock around RX resync with a bit lock
...
As Eric noted, the current wrapper for ptype func hook inside
__netif_receive_skb_list_ptype() has no chance of avoiding the indirect
call: we enter such code path only for protocols other than ipv4 and
ipv6.
Instead we can wrap the list_func invocation.
v1 -> v2:
- use the correct fix tag
Fixes: f5737cbadb ("net: use indirect calls helpers for ptype hook")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
If a network driver provides to napi_gro_frags() an
skb with a page fragment of exactly 14 bytes, the call
to gro_pull_from_frag0() will 'consume' the fragment
by calling skb_frag_unref(skb, 0), and the page might
be freed and reused.
Reading eth->h_proto at the end of napi_frags_skb() might
read mangled data, or crash under specific debugging features.
BUG: KASAN: use-after-free in napi_frags_skb net/core/dev.c:5833 [inline]
BUG: KASAN: use-after-free in napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841
Read of size 2 at addr ffff88809366840c by task syz-executor599/8957
CPU: 1 PID: 8957 Comm: syz-executor599 Not tainted 5.2.0-rc1+ #32
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188
__kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
kasan_report+0x12/0x20 mm/kasan/common.c:614
__asan_report_load_n_noabort+0xf/0x20 mm/kasan/generic_report.c:142
napi_frags_skb net/core/dev.c:5833 [inline]
napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841
tun_get_user+0x2f3c/0x3ff0 drivers/net/tun.c:1991
tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2037
call_write_iter include/linux/fs.h:1872 [inline]
do_iter_readv_writev+0x5f8/0x8f0 fs/read_write.c:693
do_iter_write fs/read_write.c:970 [inline]
do_iter_write+0x184/0x610 fs/read_write.c:951
vfs_writev+0x1b3/0x2f0 fs/read_write.c:1015
do_writev+0x15b/0x330 fs/read_write.c:1058
Fixes: a50e233c50 ("net-gro: restore frag0 optimization")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device is stacked like (team, bonding, failsafe or netvsc) the
XDP generic program for the parent device was not called.
Move the call to XDP generic inside __netif_receive_skb_core where
it can be done multiple times for stacked case.
Fixes: d445516966 ("net: xdp: support xdp generic on virtual devices")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When host is under high stress, it is very possible thread
running netdev_wait_allrefs() returns from msleep(250)
10 seconds late.
This leads to these messages in the syslog :
[...] unregister_netdevice: waiting for syz_tun to become free. Usage count = 0
If the device refcount is zero, the wait is over.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids an indirect call per RX IPv6/IPv4 packet.
Note that we don't want to use the indirect calls helper for taps.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev appears through hot plug then gets enslaved by a failover
master that is already up and running, the slave will be opened
right away after getting enslaved. Today there's a race that userspace
(udev) may fail to rename the slave if the kernel (net_failover)
opens the slave earlier than when the userspace rename happens.
Unlike bond or team, the primary slave of failover can't be renamed by
userspace ahead of time, since the kernel initiated auto-enslavement is
unable to, or rather, is never meant to be synchronized with the rename
request from userspace.
As the failover slave interfaces are not designed to be operated
directly by userspace apps: IP configuration, filter rules with
regard to network traffic passing and etc., should all be done on master
interface. In general, userspace apps only care about the
name of master interface, while slave names are less important as long
as admin users can see reliable names that may carry
other information describing the netdev. For e.g., they can infer that
"ens3nsby" is a standby slave of "ens3", while for a
name like "eth0" they can't tell which master it belongs to.
Historically the name of IFF_UP interface can't be changed because
there might be admin script or management software that is already
relying on such behavior and assumes that the slave name can't be
changed once UP. But failover is special: with the in-kernel
auto-enslavement mechanism, the userspace expectation for device
enumeration and bring-up order is already broken. Previously initramfs
and various userspace config tools were modified to bypass failover
slaves because of auto-enslavement and duplicate MAC address. Similarly,
in case that users care about seeing reliable slave name, the new type
of failover slaves needs to be taken care of specifically in userspace
anyway.
It's less risky to lift up the rename restriction on failover slave
which is already UP. Although it's possible this change may potentially
break userspace component (most likely configuration scripts or
management software) that assumes slave name can't be changed while
UP, it's relatively a limited and controllable set among all userspace
components, which can be fixed specifically to listen for the rename
events on failover slaves. Userspace component interacting with slaves
is expected to be changed to operate on failover master interface
instead, as the failover slave is dynamic in nature which may come and
go at any point. The goal is to make the role of failover slaves less
relevant, and userspace components should only deal with failover master
in the long run.
Fixes: 30c8bd5aa8 ("net: Introduce generic failover module")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce devlink_compat_switch_id_get() helper which fills up switch_id
according to passed netdev pointer. Call it directly from
dev_get_port_parent_id() as a fallback when ndo_get_port_parent_id
is not defined for given netdev.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fills a hole in softnet data, so no change in structure size.
Also prepares for xmit_more placement in the same spot;
skb->xmit_more will be removed in followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce devlink_compat_phys_port_name_get() helper that
gets the physical port name for specified netdevice
according to devlink port attributes.
Call this helper from dev_get_phys_port_name()
in case ndo_get_phys_port_name is not defined.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We prefer static_branch_unlikely() over static_key_false() these days.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit c5ad119fb6 ("net: sched: pfifo_fast use skb_array")
pfifo_fast no longer benefit from the TCQ_F_CAN_BYPASS optimization.
Due to retpolines the cost of the enqueue()/dequeue() pair has become
relevant and we observe measurable regression for the uncontended
scenario when the packet-rate is below line rate.
After commit 46b1c18f9d ("net: sched: put back q.qlen into a
single location") we can check for empty qdisc with a reasonably
fast operation even for nolock qdiscs.
This change extends TCQ_F_CAN_BYPASS support to nolock qdisc.
The new chunk of code mirrors closely the existing one for traditional
qdisc, leveraging a newly introduced helper to read atomically the
qdisc length.
Tested with pktgen in queue xmit mode, with pfifo_fast, a MQ
device, and MQ root qdisc:
threads vanilla patched
kpps kpps
1 2465 2889
2 4304 5188
4 7898 9589
Same as above, but with a single queue device:
threads vanilla patched
kpps kpps
1 2556 2827
2 2900 2900
4 5000 5000
8 4700 4700
No mesaurable changes in the contended scenarios, and more 10%
improvement in the uncontended ones.
v1 -> v2:
- rebased after flag name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.
We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.
Tested with ixgbe and CONFIG_FCOE=m
With pktgen using queue xmit:
threads vanilla patched
(kpps) (kpps)
1 2334 2428
2 4166 4278
4 7895 8100
v1 -> v2:
- rebased after helper's name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently packet_pick_tx_queue() is the only caller of
ndo_select_queue() using a fallback argument other than
netdev_pick_tx.
Leveraging rx queue, we can obtain a similar queue selection
behavior using core helpers. After this change, ndo_select_queue()
is always invoked with netdev_pick_tx() as fallback.
We can change ndo_select_queue() signature in a followup patch,
dropping an indirect call per transmitted packet in some scenarios
(e.g. TCP syn and XDP generic xmit)
This changes slightly how af packet queue selection happens when
PACKET_QDISC_BYPASS is set. It's now more similar to plan dev_queue_xmit()
tacking in account both XPS and TC mapping.
v1 -> v2:
- rebased after helper name change
RFC -> v1:
- initialize sender_cpu to the expected value
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the following patches, we are going to use __netdev_pick_tx() in
many modules. Rename it to netdev_pick_tx(), to make it clear is
a public API.
Also rename the existing netdev_pick_tx() to netdev_core_pick_tx(),
to avoid name clashes.
Suggested-by: Eric Dumazet <edumazet@google.com>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce dev_change_proto_down_generic, a generic ndo_change_proto_down
implementation, which sets the netdev carrier state according to proto_down.
This adds the ability to set protodown on vxlan and macvlan devices in a
generic way for use by control protocols like VRRPD.
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_pkt_len_init expects transport_header to be set for GSO packets.
Patch [1] skips transport_header validation for GSO packets that don't
have network_header set at the moment of calling virtio_net_hdr_to_skb,
and allows them to pass into the stack. After patch [2] no placeholder
value is assigned to transport_header if dissection fails, so this patch
adds a check to the place where the value of transport_header is used.
[1] https://patchwork.ozlabs.org/patch/1044429/
[2] https://patchwork.ozlabs.org/patch/1046122/
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The features attribute is of type u64 and stored in the native endianes on
the system. The for_each_set_bit() macro takes a pointer to a 32 bit array
and goes over the bits in this area. On little Endian systems this also
works with an u64 as the most significant bit is on the highest address,
but on big endian the words are swapped. When we expect bit 15 here we get
bit 47 (15 + 32).
This patch converts it more or less to its own for_each_set_bit()
implementation which works on 64 bit integers directly. This is then
completely in host endianness and should work like expected.
Fixes: fd867d51f ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-02-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a riscv64 JIT for BPF, from Björn.
2) Implement BTF deduplication algorithm for libbpf which takes BTF type
information containing duplicate per-compilation unit information and
reduces it to an equivalent set of BTF types with no duplication and
without loss of information, from Andrii.
3) Offloaded and native BPF XDP programs can coexist today, enable also
offloaded and generic ones as well, from Jakub.
4) Expose various BTF related helper functions in libbpf as API which
are in particular helpful for JITed programs, from Yonghong.
5) Fix the recently added JMP32 code emission in s390x JIT, from Heiko.
6) Fix BPF kselftests' tcp_{server,client}.py to be able to run inside
a network namespace, also add a fix for libbpf to get libbpf_print()
working, from Stanislav.
7) Fixes for bpftool documentation, from Prashant.
8) Type cleanup in BPF kselftests' test_maps.c to silence a gcc8 warning,
from Breno.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for getting rid of switchdev_ops, create a dedicated NDO
operation for getting the port's parent identifier. There are
essentially two classes of drivers that need to implement getting the
port's parent ID which are VF/PF drivers with a built-in switch, and
pure switchdev drivers such as mlxsw, ocelot, dsa etc.
We introduce a helper function: dev_get_port_parent_id() which supports
recursion into the lower devices to obtain the first port's parent ID.
Convert the bridge, core and ipv4 multicast routing code to check for
such ndo_get_port_parent_id() and call the helper function when valid
before falling back to switchdev_port_attr_get(). This will allow us to
convert all relevant drivers in one go instead of having to implement
both switchdev_port_attr_get() and ndo_get_port_parent_id() operations,
then get rid of switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a25717d2b6 ("xdp: support simultaneous driver and
hw XDP attachment") users can load an XDP program for offload and
in native driver mode simultaneously. Allow a similar mix of
offload and SKB mode/generic XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In order to provide more meaningful messages to user when the process of
loading xdp program onto network interface failed, let's add extack
messages within dev_change_xdp_fd.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Assign a default net namespace to netdevs created by init_dummy_netdev().
Fixes a NULL pointer dereference caused by busy-polling a socket bound to
an iwlwifi wireless device, which bumps the per-net BUSYPOLLRXPACKETS stat
if napi_poll() received packets:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000190
IP: napi_busy_loop+0xd6/0x200
Call Trace:
sock_poll+0x5e/0x80
do_sys_poll+0x324/0x5a0
SyS_poll+0x6c/0xf0
do_syscall_64+0x6b/0x1f0
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
Fixes: 7db6b048da ("net: Commonize busy polling code to focus on napi_id instead of socket")
Signed-off-by: Josh Elsasser <jelsasser@appneta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".
The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:
#if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
# define HAVE_JUMP_LABEL
#endif
We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.
Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
This avoids an indirect calls for L3 GRO receive path, both
for ipv4 and ipv6, if the latter is not compiled as a module.
Note that when IPv6 is compiled as builtin, it will be checked first,
so we have a single additional compare for the more common path.
v1 -> v2:
- adapted to INDIRECT_CALL_ changes
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device address is about to be changed, or an address added to the
list of device HW addresses, it is necessary to ensure that all
interested parties can support the address. Therefore, send the
NETDEV_PRE_CHANGEADDR notification, and if anyone bails on it, do not
change the address.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETDEV_CHANGEADDR notification is emitted after a device address
changes. Extending this message to allow vetoing is certainly possible,
but several other notification types have instead adopted a simple
two-stage approach: first a "pre" notification is sent to make sure all
interested parties are OK with a change that's about to be done. Then
the change is done, and afterwards a "post" notification is sent.
This dual approach is easier to use: when the change is vetoed, nothing
has changed yet, and it's therefore unnecessary to roll anything back.
Therefore adopt it for NETDEV_CHANGEADDR as well.
To that end, add NETDEV_PRE_CHANGEADDR and an info structure to go along
with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will add a notifier type NETDEV_PRE_CHANGEADDR, which
allows vetoing of MAC address changes. One prominent path to that
notification is through dev_set_mac_address(). Therefore give this
function an extack argument, so that it can be packed together with the
notification. Thus a textual reason for rejection (or a warning) can be
communicated back to the user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julio Faracco