Many PCI host controller drivers aren't prepared to have their devices
unbound from them forcefully (e.g., through /sys/.../<driver>/unbind), as
they don't provide any driver .remove callback, where they'd detach the
root bus, release resources, etc. Keeping the driver built in (i.e., not a
loadable module) is not enough; and providing no .remove callback just
means we don't do any teardown.
To rule out the possibility of unbinding a device via sysfs, we need to set
the ".suppress_bind_attrs" field.
I found the suspect drivers via the following search:
git grep -l platform_driver $(git grep -L -e '\.remove' -e suppress_bind_attrs drivers/pci/)
Then I inspected them to ensure that
(a) they set up a PCI bus in their probe() and
(b) they don't have a remove() callback for undoing the setup
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
SZ_16M PEM resource size includes PEM-specific register and its children
resources. Reservation of the whole SZ_16M range leads to child device
driver failure when pcieport driver is requesting resources:
pcieport 0004:1f:00.0: can't enable device: BAR 0 [mem 0x87e0c0f00000-0x87e0c0ffffff 64bit] not claimed
So we cannot reserve full 16M here and instead we want to reserve
PEM-specific register only which is SZ_64K.
At the end increase PEM resource to SZ_16M since this is what
thunder_pem_init() call expects for proper initialization.
Fixes: 9abb27c759 ("PCI: thunder-pem: Add legacy firmware support for Cavium ThunderX host controller")
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.10+
During early days of PCI quirks support, ThunderX firmware did not provide
PNP0c02 node with PCI configuration space and PEM-specific register ranges.
This means that for legacy FW we are not reserving these resources and
cannot gather PEM-specific resources for further PEM initialization.
To support already deployed legacy FW, calculate PEM-specific ranges and
provide resources reservation as fallback scenario into PEM driver when we
could not gather PEM reg base from ACPI tables.
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
"CAV" is the only PNP/ACPI hardware ID vendor prefix assigned to Cavium so
fix this as it should be from day one.
Fixes: 44f22bd91e ("PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller")
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
The pci-thunder-pem driver was initially developed for cn88xx SoCs. The
cn81xx and cn83xx members of the same family of SoCs have a slightly
different configuration of interrupt resources in the PEM hardware, which
prevents the INTA legacy interrupt source from functioning with the current
driver.
There are two fixes required:
1) Don't fixup the PME interrupt on the newer SoCs as it already has the
proper value.
2) Report MSI-X Capability Table Size of 2 for the newer SoCs, so the core
MSI-X code doesn't inadvertently clobber the INTA machinery that happens to
reside immediately following the table.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX PCIe controller to off-chip devices (so-called PEM) is not fully
compliant with ECAM standard. It uses non-standard configuration space
accessors (see thunder_pem_ecam_ops) and custom configuration space
granulation (see bus_shift = 24). In order to access configuration space
and probe PEM as ACPI-based PCI host controller we need to add MCFG quirk
infrastructure. This involves:
1. A new thunder_pem_acpi_init() init function to locate PEM-specific
register ranges using ACPI.
2. Export PEM thunder_pem_ecam_ops structure so it is visible to MCFG quirk
code.
3. New quirk entries for each PEM segment. Each contains platform IDs,
mentioned thunder_pem_ecam_ops and CFG resources.
Quirk is considered for ThunderX silicon pass2.x only which is identified
via MCFG revision 1.
ThunderX pass 2.x requires the following accessors:
NUMA Node 0 PCI segments 0- 3: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA Node 1 PCI segments 10-13: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: adapt to use acpi_get_rc_resources(), update Makefile/ifdefs so
quirk doesn't depend on CONFIG_PCI_HOST_THUNDER_PEM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull the register resource lookup out of thunder_pem_init() so we can
easily add a corresponding lookup using ACPI. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_HOST_THUNDER_PEM
drivers/pci/host/Kconfig: bool "Cavium Thunder PCIe controller to off-chip devices"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: David Daney <david.daney@cavium.com>
Add a parent device field to struct pci_config_window. The parent is not
saved now, but will be useful to save it in some cases. For ACPI on ARM64,
it can be used to setup ACPI companion and domain.
Since the parent dev is in struct pci_config_window now, we need not pass
it to the init function as a separate argument.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This header will be used from arch/arm64 for ACPI PCI implementation so it
needs to be moved out of drivers/pci.
Update users of the header file to use the new name. No functional
changes.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
* pci/arm64:
PCI, of: Move PCI I/O space management to PCI core code
PCI: generic, thunder: Use generic ECAM API
PCI: Provide common functions for ECAM mapping
* pci/host-hv:
PCI: hv: Add explicit barriers to config space access
Use functions provided by drivers/pci/ecam.h for mapping the config space
in drivers/pci/host/pci-host-common.c, and update its users to use 'struct
pci_config_window' and 'struct pci_ecam_ops'.
The changes are mostly to use 'struct pci_config_window' in place of
'struct gen_pci'. Some of the fields of gen_pci were only used temporarily
and can be eliminated by using local variables or function arguments, these
are not carried over to struct pci_config_window.
pci-thunder-ecam.c and pci-thunder-pem.c are the only users of the
pci_host_common_probe function and the gen_pci structure; these have been
updated to use the new API as well.
The patch does not introduce any functional changes other than a very minor
one: with the new code, on 64-bit platforms, we do just a single ioremap
for the whole config space.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The 32-bit addressing modes in the I/O and Prefetchable Memory registers
are required to be read-only. Since the underlying access method allows
them to be set, emulate their read-only nature and always set them.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The root complexes used to access off-chip PCIe devices (called PEM units
in the hardware manuals) on some Cavium ThunderX processors require quirky
access methods for the config space of the PCIe bridge.
Add a driver to provide these config space accessor functions. Use the
pci-host-common code to configure the PCI machinery.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
