The layering interfaces are used to implement the Infiniband protocols
and the ethernet emulation driver.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
These files introduce a char device that userspace apps use to gain
direct memory-mapped access to the InfiniPath hardware, and routines for
pinning and unpinning user memory in cases where the hardware needs to
DMA into the user address space.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipathfs filesystem contains files that are not appropriate for
sysfs, because they contain binary data. The hierarchy is simple; the
top-level directory contains driver-wide attribute files, while numbered
subdirectories contain per-device attribute files.
Our userspace code currently expects this filesystem to be mounted on
/ipathfs, but a final location has not yet been chosen.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
EEPROM support, interrupt handling, statistics gathering, and write
combining management for x86_64.
A note regarding i2c: The Atmel EEPROM hardware we use looks like an
i2c device electrically, but is not i2c compliant at all from a
functional perspective. We tried using the kernel's i2c support to
talk to it, but failed.
Normal i2c devices have a single 7-bit or 10-bit i2c address that they
respond to. Valid 7-bit addresses range from 0x03 to 0x77. Addresses
0x00 to 0x02 and 0x78 to 0x7F are special reserved addresses
(e.g. 0x00 is the "general call" address.) The Atmel device, on the
other hand, responds to ALL addresses. It's designed to be the only
device on a given i2c bus. A given i2c device address corresponds to
the memory address within the i2c device itself.
At least one reason why the linux core i2c stuff won't work for this
is that it prohibits access to reserved addresses like 0x00, which are
really valid addresses on the Atmel devices.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_init_chip.c sets up an InfiniPath device for use.
ipath_diag.c permits userspace diagnostic tools to read and write a
chip's registers. It is different in purpose from the mmap interfaces
to the /sys/bus/pci resource files.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This file contains routines and definitions specific to InfiniPath
devices that have PCI Express interfaces.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipath_ht400.c file contains routines and definitions specific to
HyperTransport-based InfiniPath devices.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_common.h and ips_common.h contain definitions shared between
userspace and the kernel.
ipath_kernel.h is the core driver header file.
ipath_debug.h contains mask values used for controlling driver debugging.
ipath_registers.h contains bitmask definitions used in chip registers.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipath driver is a low-level driver for PathScale InfiniPath host
channel adapters (HCAs) based on the HT-400 and PE-800 chips, including
the InfiniPath HT-460, the small form factor InfiniPath HT-460, the
InfiniPath HT-470 and the Linux Networx LS/X.
The ipath_driver.c file contains much of the low-level device handling
code.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Decrease the number of pointer derefs in drivers/serial/jsm/jsm_tty.c
Benefits of the patch:
- Fewer pointer dereferences should make the code slightly faster.
- Size of generated code is smaller
- Improved readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "V. ANANDA KRISHNAN" <mansarov@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
And remove the comments that were put in inplace of a fix too....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently a device failure during recovery leaves bits set in the bitmap.
This normally isn't a problem as the offending device will be rejected because
of errors. However if device re-adding is being used with non-persistent
bitmaps, this can be a problem.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the old radeon driver which has been replaced by a
newer one.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The monochrome->color expansion routine that handles bitmaps which have
(widths % 8) != 0 (slow_imageblit) produces corrupt characters in big-endian.
This is caused by a bogus bit test in slow_imageblit().
Fix.
This patch may deserve to go to the stable tree. The code has already been
well tested in little-endian machines. It's only in big-endian where there is
uncertainty and Herbert confirmed that this is the correct way to go.
It should not introduce regressions.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes for the pxafb driver:
* Return -EINVAL for resolutions that are too large as per framebuffer
driver policy.
* Increase the error timeout for disabling the LCD controller. The current
timeout is sometimes too short on the Sharp Zaurus Cxx00 hardware and an
extra delay in an error path shouldn't pose any problems.
* Fix a dev reference which causes a compile error when DEBUG is defined.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Generalise the Corgi backlight driver by moving the default intensity and
limit mask settings into the platform specific data structure. This enables
the driver to support other Zaurus hardware, specifically the SL-6000x (Tosa)
model.
Also change the spinlock to a mutex (the spinlock is overkill).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updates to the HP Jornada 680 Backlight driver:
- Correct the suspend/resume functions so the driver compiles
(SUSPEND_POWER_DOWN/RESUME_POWER_ON no longer exist).
- Convert the driver to match the recent platform device changes.
- Replace the unsafe static struct platform_device with dynamic allocation.
- Convert the driver to the new backlight code.
This has not been tested on a device due to lack of hardware but wouldn't
compile beforehand.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Backlight class attributes are currently easy to implement incorrectly.
Moving certain handling into the backlight core prevents this whilst at the
same time makes the drivers simpler and consistent. The following changes are
included:
The brightness attribute only sets and reads the brightness variable in the
backlight_properties structure.
The power attribute only sets and reads the power variable in the
backlight_properties structure.
Any framebuffer blanking events change a variable fb_blank in the
backlight_properties structure.
The backlight driver has only two functions to implement. One function is
called when any of the above properties change (to update the backlight
brightness), the second is called to return the current backlight brightness
value. A new attribute "actual_brightness" is added to return this brightness
as determined by the driver having combined all the above factors (and any
driver/device specific factors).
Additionally, the backlight core takes care of checking the maximum brightness
is not exceeded and of turning off the backlight before device removal.
The corgi backlight driver is updated to reflect these changes.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add acceleration support in w100fb.c (i.e. ATI Imageons) for the copyarea and
fillrect operations.
Signed-off-by: Alberto Mardegan <mardy@users.sourceforge.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current display was not saved during initialization. This leads to hard
to track console corruption, such as a misplaced cursor, which is correctible
by switching consoles. Fix this minor bug.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an LED trigger for IDE disk activity to the ide-disk driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ensure ide-taskfile.c calls any driver specific end_request function if
present.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds LED drivers for LEDs found on the Sharp Zaurus c6000 model (tosa).
Signed-off-by: Dirk Opfer <dirk@opfer-online.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NEW_LEDS support for ixp4xx boards where LEDs are connected to the GPIO lines.
This includes a new generic ixp4xx driver (leds-ixp4xx-gpio.c name
"IXP4XX-GPIO-LED")
Signed-off-by: John Bowler <jbowler@acm.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds an LED driver for LEDs exported by the Sharp LOCOMO chip as found on some
models of Sharp Zaurus.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds LED drivers for LEDs found on the Sharp Zaurus c7x0 (corgi, shepherd,
husky) and cxx00 (akita, spitz, borzoi) models.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an example of a complex LED trigger in the form of a generic timer which
triggers the LED its attached to at a user specified frequency and duty cycle.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for LED triggers to the LED subsystem. "Triggers" are events
which change the state of an LED. Two kinds of trigger are available, simple
ones which can be added to exising code with minimum disruption and complex
ones for implementing new or more complex functionality.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the foundations of a new LEDs subsystem. This patch adds a class which
presents LED devices within sysfs and allows their brightness to be
controlled.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add TIOCL_GETKMSGREDIRECT needed by the userland suspend tool to get the
current value of kmsg_redirect from the kernel so that it can save it and
restore it after resume.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete two useless kmalloc wrappers and use kmalloc/kzalloc. Some weird
NULL checks are also simplified.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The "3c59x: use mii_check_media" patch introduced a netif_carrier_off in
vortex_up. 10base2 stoped working because of this. This is removed.
Tx/Rx reset is back in vortex_up because the 3c900B-Combo stops working after
changing from half duplex to full duplex when Tx/Rx reset is done with
vortex_timer.
Also brought back some mii stuff to be sure that it does not break something
else.
Thanks to Pete Clements <clem@clem.clem-digital.net> for reporting and testing.
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pre-2.6.16 patch "3c59x collision statistics fix" accidentally caused
vortex_error() to not run iowrite16(TxEnable, ioaddr + EL3_CMD) if we got a
maxCollisions interrupt but MAX_COLLISION_RESET is not set.
Thanks to Pete Clements <clem@clem.clem-digital.net> for reporting and testing.
Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert the remaining semaphores to mutexes in the IPMI driver. The
watchdog was using a semaphore as a real semaphore (for IPC), so the
conversion there required adding a completion.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tidy up various coding standard things, mostly removing the space after !,
but also break some long lines and fix a few other spacing inconsistencies.
Also fixes some bad error reporting when deleting an IPMI user.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Matt Domsch noticed a startup race with the IPMI kernel thread, it was
possible (though extraordinarly unlikely) that a message could come in
before the upper layer was ready to handle it. This patch splits the
startup processing of an IPMI interface into two parts, one to get ready
and one to actually start the processes to receive messages from the
interface.
[akpm@osdl.org: cleanups]
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alan sayeth "Based on Linus original comments about _GPL we should export
tty_insert_flip_char as EXPORT_SYMBOL because it used to be EXPORT_SYMBOL
equivalent (trivial inline). The other features are new extensions are were
not available to drivers before so need not be provided except as _GPL
functionality as far as I can see."
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=6294
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Philippe Vouters <Philippe.Vouters@laposte.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EDAC_752X uses pci_scan_single_device(), which is only available if
CONFIG_HOTPLUG is enabled, so limit this driver with HOTPLUG.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dave Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kconfig sanitized around drivers/net
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an obvious off-by-one error (vmax_mtd[] contains two elements).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/mtd/devices/blkmtd.c uses a local declaration of name_to_dev_t()
which is inconsistant with the real one. the following patch fixes this by
removing the local declaration and including mount.h instead
this patch was originally done by Micah Anderson.
Signed-off-by: Herbert Poetzl <herbert@13thfloor.at>
Acked-by: Micah Anderson <micah@riseup.net>
Acked-by: Daniel Hokka Zakrisson <daniel@hozac.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Redboot simply sets the first character of a fis entry to 0xff on "fis
delete". The kernel redboot parser stops parsing on such an entry, and
without this patch any entries after a deleted image would not be detected.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds flash chip used in Sharp Zaurus sl5500 (collie) to jedec_probe.
Values work for read-only access, but I have not figured out how to do
read-write.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes coverity bug #12. The first two gotos in the function still
have the initial value for mtd set. And the third goto just triggers for
!mtd
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kill unneccessary ifdefs in mtdcore.c.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a copy/paste bug found by cpminer inside the inftlcore.c file
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current cmdlinepart.c uses offset value 0 to specify a continuous
partition. This prevents creating a second partition starting at 0.
For example, I can split 4MB device using "mtdparts=id:2M,2M", but I can
not do "mtdparts=id:2M@2M,2M@0" to swap mtd0 and mtd1.
This patch introduces special OFFSET_CONTINUOUS value for a continuous
partition and allows 0 for offset value.
Also this patch replaces 0xffffffff with UINT_MAX for SIZE_REMAINING.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MTD_NAND=m and MTD_NAND_SHARPSL=y or MTD_NAND_NANDSIM=y are illegal
combinations that mustn't be allowed.
This patch fixes this bug by making MTD_NAND_SHARPSL and MTD_NAND_NANDSIM
tristate's.
Additionally, it fixes some whitespace damage at these options.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: "Artem B. Bityutskiy" <dedekind@yandex.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- chips/sharp.c: make two needlessly global functions static
- move some declarations to a header file where they belong to
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/mtd/devices/m25p80.c: In function `m25p80_erase':
drivers/mtd/devices/m25p80.c:189: warning: signed size_t format, different type arg (arg 6)
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This ugly hack add support for Siemens MC45 PCMCIA GPRS card (which is
identical to Possio GCC, and which is offered by one of our local GPRS
providers). Card has unfortunate feature that after poweron oxcf950 chip
is fully powered and works, but attached MC45 modem is powered down :-(
There is a special sequence (which takes 1 sec :-( ) to poweron MC45 (and
after MC45 powers on, it takes more than 2 secs until firmware fully
boots...) which needs to be executed after all powerons.
I'm really not familiar with PCMCIA subsystem, so I have no idea whether I
should issue request_region() on rest of oxcf950 address range (0-7 is
UART, 8-F are special configuration registers), or how this should be
better integrated with PM system and so on - I just put it in same place
where another hack already lived...
Card uses 18.432MHz XTAL, so to get it to work you must add lines below to
the /etc/pcmcia/serial.opts.
case "$MANFID-$FUNCID-$PRODID_1-$PRODID_2-$PRODID_3-$PRODID_4" in
'030c,0003-2-GPRS-CARD--')
SERIAL_OPTS="baud_base 1152000"
;;
esac
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If the driver for the primary pseudo device is removed from the device,
the secondary driver must be removed as well -- it cannot exist on its own.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of the two status values struct pcmcia_device->p_state and state,
use descriptive bitfields. Most value-checking in drivers was invalid, as
the core now only calls the ->remove() (a.k.a. detach) function in case the
attachement _and_ configuration was successful.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove the unused DEV_RELEASE_PENDING flag, and move the DEV_SUSPEND flag
into the p_dev structure, and make use of it at the core level.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
We can now make pcmcia_release_{io,irq} static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Most of the driver initialization isn't done in the .probe function, but in
the internal _config() functions. Make them return a value, so that .probe
can properly report whether the probing of the device succeeded or not.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
dev_link_t * and client_handle_t both mean struct pcmcai_device * by now.
Therefore, remove all such indirections.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Embed dev_link_t into struct pcmcia_device(), as they basically address the
same entity. The actual contents of dev_link_t will be cleaned up step by step.
This patch includes a bugfix from and signed-off-by Andrew Morton.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Rename pcmcia_device.state (which is used in very few places) to p_state
in order to avoid a namespace collision when moving the deprecated
dev_link_t into struct pcmcia_device
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we do not allow setting Vcc in the pcmcia core, and Vpp1 and
Vpp2 can only be set to the same value, a lot of code can be
streamlined.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Handle the _modifying_ operation sm91c92_cs requires in
pcmcia_modify_configuration, so that the only remaining users
of pcmcia_release_configuration() are within the pcmcia core
module.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In all but one case, the suspend and resume functions of PCMCIA drivers
contain mostly of calls to pcmcia_release_configuration() and
pcmcia_request_configuration(). Therefore, move this code out of the
drivers and into the core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Convert the remaining drivers which use pcmcia_release_io or
pcmcia_release_irq, and remove the EXPORT of these symbols.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_disable_device(struct pcmcia_device *p_dev) performs the necessary
cleanups upon device or driver removal: it calls the appropriate
pcmcia_release_* functions, and can replace (most) of the current drivers'
_release() functions.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
ata_xfer_tbl is terminated by entry with -1 as ->shift. However,
->shift was unsigned int making the termination condition bogus. This
patch converts ->shift and ->bits to int.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is no reason for the issuer to diddle with a failed qc as the
issuer has complete control over when a qc gets freed (usually in
->complete_fn). Make ata_qc_issue() responsible for completing qcs
which failed to issue.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On sg_err failure path, ata_qc_issue() doesn't mark the qc active
before returning. This triggers WARN_ON() in __ata_qc_complete() when
the qc gets completed. This patch moves ap->active_tag and
QCFLAG_ACTIVE setting to the top of the function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
MAP tables of ich6 and ich6m are wrong. Depending on port usage,
ata_piix may fail to initialize attached devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the Compact Flash controller integrated in
the Atmel AT91RM9200 processor.
Signed-off-by: Andrew Victor <andrew@sanpeople.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
socket.functions is the number of functions, and so must be one larger
than the maximum function number.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_request_io() doesn't mark the resource as busy in 2.6., therefore
there's no need to work around the registration of the resources into the
resource tree.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
BasePort, NumPorts and Attributes are or can be embedded in
struct resource, so remove them.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If the kernel is configured to not include the deprecated PCMCIA ioctl,
some code doesn't need to be built.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove the compatibility wrappers, as they can (now) also be implemented
using macros. Please continue using these wrappers instead of new functions
until a new API has stabilized.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use mutexes in the PCMICA core, as they suffice for what needs to be done.
Includes a bugfix from and Signed-off-by Andrew Morton.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Update the remaining users using the static lookup table of the PCMCIA
function configuration to use the struct pcmcia_device-contained pointer.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Access the PCMCIA config_t struct (one per device function) using
a pointer in struct pcmcia_device, instead of looking them up in
an array.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
config_t.Present is set to the same value as CardValues, which isn't modified
anywhere. Therefore, we can use only one of these two objects.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
For some time, the core pcmcia drivers seem not to think single
character prod_ids are valid, thus preventing the "cleverly" named
"D" "Link DWL-650 11Mbps WLAN Card"
Before (as in 2.6.16):
PRODID_1=""
PRODID_2="Link DWL-650 11Mbps WLAN Card"
PRODID_3="Version 01.02"
PRODID_4=""
MANFID=0156,0002
FUNCID=6
After (with the patch)
PRODID_1="D"
PRODID_2="Link DWL-650 11Mbps WLAN Card"
PRODID_3="Version 01.02"
PRODID_4=""
MANFID=0156,0002
FUNCID=6
Signed-off-by: Janos Farkas <chexum@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6: (24 commits)
[PARISC] Fix double free when removing HIL drivers
[PARISC] Add atomic_sub_and_test
[PARISC] Enabled some NLS modules in a500, b180 and c3000 defconfigs
[PARISC] Kill duplicated EXPORT_SYMBOL warnings
[PARISC] Move ioremap EXPORT_SYMBOL from parisc_ksyms.c
[PARISC] Make local_t use atomic_long_t
[PARISC] Update defconfigs
[PARISC] Add PREEMPT support
[PARISC] More useful readwrite lock helpers
[PARISC] Convert HIL drivers to use input_allocate_device
[PARISC] Fixup CONFIG_EISA a bit
[PARISC] getsockopt should be ENTRY_COMP
[PARISC] Remove obsolete CONFIG_DEBUG_IOREMAP
[PARISC] Temporary FIXME for ioremapping EISA regions
[PARISC] Enable ioremap functionality unconditionally
[PARISC] Fix stifb with IOREMAP and a 64-bit kernel
[PARISC] Add CONFIG_HPPA_IOREMAP to conditionally enable ioremap
[PARISC] Add STRICT_MM_TYPECHECKS
[PARISC] Fix IOREMAP with a 64-bit kernel
[PARISC] Add parisc implementation of flush_kernel_dcache_page()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mad: RMPP support for additional classes
IB/mad: include GID/class when matching receives
IB/mthca: Fix section mismatch problems
IPoIB: Fix oops with raw sockets
IB/mthca: Fix check of size in SRQ creation
IB/srp: Fix unmapping of fake scatterlist
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] sata_mv: three bug fixes
[PATCH] libata: ata_dev_init_params() fixes
[PATCH] libata: Fix interesting use of "extern" and also some bracketing
[PATCH] libata: Simplex and other mode filtering logic
[PATCH] libata - ATA is both ATA and CFA
[PATCH] libata: Add ->set_mode hook for odd drivers
[PATCH] libata: BMDMA handling updates
[PATCH] libata: kill trailing whitespace
[PATCH] libata: add FIXME above ata_dev_xfermask()
[PATCH] libata: cosmetic changes in ata_bus_softreset()
[PATCH] libata: kill E.D.D.
On Thu, Mar 30, 2006 at 08:31:02AM -0500, Dmitry Torokhov wrote:
> Don't do that, its double free. input_unregister_device() normally
> causes release() to be called and free the device. input_free_device
> is only to be called when input_register_device has not been called or
> failed.
>
> Plus you might want to unregister device after closing serio port,
> otherwise your interrupt routine might be referencing already freed
> memory.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Kill various warnings when built using ioremap.
Remove stifb_{read,write} functions, which are now obsolete (and stack abusers!)
Disable stifb mmap() functionality on a 64-bit kernel, it will crash the
machine.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Addresses in F-space must be accessed uncached on most parisc machines.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Add RMPP support for additional management classes that support it.
Also, validate RMPP is consistent with management class specified.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Received responses are currently matched against sent requests based
on TID only. According to the spec, responses should match based on
the combination of TID, management class, and requester LID/GID.
Without the additional qualification, an agent that is responding to
two requests, both of which have the same TID, can match RMPP ACKs
with the incorrect transaction. This problem can occur on the SM node
when responding to SA queries.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
(1) A DMA transfer size of 0x10000 was not being written
as 0x0000 in the PRDs. Fixed.
(1) The DEV_IRQ interrupt cause bit happens spuriously
during EDMA operation, and was not being ignored by the driver.
This led to various "drive busy" errors being reported,
with associated unpredictable behaviour. Fixed.
(2) If a SATA or PCI interrupt was received with no outstanding
command, the interrupt handler still attempted to invoke
ata_qc_complete(), triggering assert()/BUG_ON() behaviour
elsewhere in libata. Fixed.
The driver still has issues with confusion after error-recovery,
but should now be reliable in the absence of drive errors.
I will be looking more into the error-handling bugs next.
Signed-Off-By: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_init_params() fixes:
- Get the "heads" and "sectors" parameters from caller instead of implicitly from dev->id[].
- Return AC_ERR_INVALID instead of 0 if an invalid parameter is found
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Last of the set, just clean up some oddments. Assuming the whole set is
now ok then the remaining differences are the setup of PIO_0 at reset
and the ->data_xfer method.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a field to the host_set called 'flags' (was host_set_flags changed
to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel
Add a ->mode_filter() hook to allow drivers to filter modes
Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core
This provides the needed framework to support all the mode rules found
in the PATA world. The simplex filter deals with 'to spec' simplex DMA
systems found in older chips. The cable filter avoids duplicating the
same rules in each chip driver with PATA. Finally the mode filter is
neccessary because drive/chip combinations have errata that forbid
certain modes with some drives or types of ATA object.
Drive speed setup remains per channel for now and the filters now use
the framework Tejun put into place which cleans them up a lot from the
older libata-pata patches.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I think this is still needed with the new probe code (which btw seems to
be missing docs in upstream ?).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some hardware doesn't want the usual mode setup logic running. This
allows the hardware driver to replace it for special cases in the least
invasive way possible.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is the minimal patch set to enable the current code to be used with
a controller following SFF (ie any PATA and early SATA controllers)
safely without crashes if there is no BMDMA area or if BMDMA is not
assigned by the BIOS for some reason.
Simplex status is recorded but not acted upon in this change, this isn't
a problem with the current drivers as none of them are for simplex
hardware. A following diff will deal with that.
The flags in the probe structure remain ->host_set_flags although Jeff
asked me to rename them, simply because the rename would break the usual
Linux rules that old code should break when there are changes. not
compile and run and then blow up/eat your computer/etc. Renaming this
later is a trivial exercise once a better name is chosen.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
gcc4 doesn't like us declaring a static function inside another
function. We can do away with this construct altogether and use
BUILD_BUG_ON() instead (idea from Andi Kleen.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Added code to check for invalid MAC address from eeprom or user input.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The comments concerning how the pcnet32 ethernet device driver selects
the MAC addr to use are incorrect. A recent patch (in the last 3 months)
changed how the code worked, but did not change the comments.
Side comment: the new behaviour is good; I've got a pcnet32 card which
powers up with garbage in the CSR's, and a good MAC addr in the PROM.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't bother testing for CONFIG_NET_CBUS ("NEC PC-9800 C-bus cards"); it went
out with the rest of PC98 subarch.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The natsemi chip can have a larger EEPROM attached than it itself uses for
configuration. This patch adds support for user space access to such an
EEPROM.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Cc: Tim Hockin <thockin@hockin.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This enables TX checksum offloading for the spidernet driver by default.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the bonding master to specify its carrier state
based upon the state of the slaves. For 802.3ad, the bond is up if
there is an active, parterned aggregator. For other modes, the bond is
up if any slaves are up. Updates driver version to 3.0.3.
Based on a patch by jamal <hadi@cyberus.ca>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix section mismatches in acenic driver:
WARNING: drivers/net/acenic.o - Section mismatch: reference to .init.data:tigon2FwText from .text between 'acenic_probe_one' (at offset 0x2409) and 'ace_interrupt'
WARNING: drivers/net/acenic.o - Section mismatch: reference to .init.data:tigon2FwRodata from .text between 'acenic_probe_one' (at offset 0x2422) and 'ace_interrupt'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch reduces the message level of the RX ram full messages
from err to debug to prevent spamming the console leaving it in the
logfiles though.
From: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Problems with link state detection have been reported several times in the
past months.
Denis Vlasenko did all the work tracking it down. Jeff Garzik suggested the
proper place for the fix.
When using the mii library, the driver needs to check mii->force_media
and set dev->state accordingly.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Initializing the b44 MAC & PCI functional blocks in the controller must
occur inside init_one(). This will allow access to the MAC registers.
The controller was being powered up in b44_open() which would not allow
access to the registers before ifconfig was up.
Philip Kohlbecher found this bug.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Allow the 8250 probe modules to be disabled if we're building for
with EMBEDDED enabled. This reduces the kernel size by not including
unnecessary probe module support.
Original idea from Matt Mackall for PCI only, expanded to others by
rmk.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (67 commits)
[PATCH] powerpc: Remove oprofile spinlock backtrace code
[PATCH] powerpc: Add oprofile calltrace support to all powerpc cpus
[PATCH] powerpc: Add oprofile calltrace support
[PATCH] for_each_possible_cpu: ppc
[PATCH] for_each_possible_cpu: powerpc
[PATCH] lock PTE before updating it in 440/BookE page fault handler
[PATCH] powerpc: Kill _machine and hard-coded platform numbers
ppc: Fix compile error in arch/ppc/lib/strcase.c
[PATCH] git-powerpc: WARN was a dumb idea
[PATCH] powerpc: a couple of trivial compile warning fixes
powerpc: remove OCP references
powerpc: Make uImage default build output for MPC8540 ADS
powerpc: move math-emu over to arch/powerpc
powerpc: use memparse() for mem= command line parsing
ppc: fix strncasecmp prototype
[PATCH] powerpc: make ISA floppies work again
[PATCH] powerpc: Fix some initcall return values
[PATCH] powerpc: Workaround for pSeries RTAS bug
[PATCH] spufs: fix __init/__exit annotations
[PATCH] powerpc: add hvc backend for rtas
...
Quite a few cleanup functions in mthca were marked as __devexit.
However, they could also be called from error paths during
initialization, so they cannot be marked that way. Just delete all of
the incorrect annotations.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_hard_header() needs to handle the case that daddr is NULL. This
can happen when packets are injected via a raw socket, and IPoIB
shouldn't oops in this case.
Reported by Anton Blanchard <anton@samba.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The previous patch for Tavor broke MemFree logic.
The driver should perform limit check only for Tavor. For MemFree,
the check is incorrect, since ds (WQE stride) is always a power-of-2
(although the max_desc_size may not be).
In Tavor, however, WQE stride and desc_size are the same, and are not
necessarily power-of-2. The check was really for the WQE stride (and
it Tavor, we use max_desc_size for the stride).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The recently merged patch to create a fake scatterlist for non-SG SCSI
commands had a bug: the driver ended up doing dma_unmap_sg() on a
scatterlist scmnd->request_buffer rather than the fake scatter list it
created. Fix this so that the driver unmaps the same thing it maps.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than each driver test MMC_DEBUG itself, and define DEBUG,
pass it in via the makefile instead.
Fix drivers to use pr_debug() where appropriate, and avoid defining
a DEBUG() macro.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds OMAP MMC driver.
Signed-off-by: Juha Yrjölä <juha.yrjola@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I'm not really certain what the thinking was but the code obviously wanted to
walk processes other than just those in it's session, for purposes of do_SAK.
Just walking those tasks that don't have a session assigned sounds at the very
least incomplete.
So modify the code to kill everything in the session and anything else that
might have the tty open. Hopefully this helps if the do_SAK functionality is
ever finished.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We already have the tasklist_lock so there is no need for us to reacquire it
with send_group_sig_info. reader/writer locks allow multiple readers and thus
recursion so the old code was ok just wastful.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This warning happens in practice because the resource length reported by
the chipset is too large. This is not actually a problem, so don't warn
about it. If it happens to be too small, warn about that, but with
a different message so people who are used to ignoring the old message
don't.
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
- move call of scsi_print_command from sbp2_send_command to the beginning of
sbp2_queue_command to show also commands which are not sent
- put sbp2's name into scsi_print_sense
- use __FUNCTION__ in log messages
- remove a few less useful log messages and comments
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
Sbp2 relied on DID_OK to be defined as 0. Always shift DID_OK into the right
position anyway, and explicitly return DID_OK together with CHECK_CONDITION.
Also comment on some #if 0 code. The patch does not change current behaviour.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
No need to hide it from /sys/module/ieee1394/parameters/.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
Skip the main timer code if interrupts are disabled in the full lock
state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.
IBM reported a problem on powerpc blades during ethtool self test
that was caused by the memory test taking excessively long. Config.
cycles are very slow on powerpc and the memory test can take more
than 10 seconds to complete using config. cycles. As a result, NETDEV
WATCHDOG can be triggered during self test and the chip can end up in
a funny state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bryan O'Sullivan