The driver call nand_scan_ident in 8 bit mode, then
readid or onfi detection are done (and detect bus width).
The driver should update its bus width before calling nand_scan_tail.
This work because readid and onfi are read work 8 byte mode.
Note that nand_scan_ident send command (NAND_CMD_RESET, NAND_CMD_READID, NAND_CMD_PARAM), address and read data
The ONFI specificication is not very clear for x16 device if high byte of address should be driven to 0,
but according to [1] it should be ok to not drive it during autodetection.
[1]
3.3.2. Target Initialization
[...]
The Read ID and Read Parameter Page commands only use the lower 8-bits of the data bus.
The host shall not issue commands that use a word data width on x16 devices until the host
determines the device supports a 16-bit data bus width in the parameter page.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This is required by NAND flash driver for initializing wait counters.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
By replacing a kthread with a workqueue, the code is now a bit clearer.
There's also a slight reduction of code size (numbers apply for x86):
Before:
text data bss dec hex filename
3248 36 0 3284 cd4 drivers/mtd/mtd_blkdevs.o
After:
text data bss dec hex filename
3150 36 0 3186 c72 drivers/mtd/mtd_blkdevs.o
Due to lack of real hardware, tests have been performed on an emulated
environment with mtdswap and mtdblock over nandsim devices.
Some real testing should be done, before merging this patch.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The map_word_load() function initializes exactly
as many words in the buffer as required, but gcc
cannot figure this out and gives a misleading
warning. Marking the local variable as
uninitialized_var shuts up that warning.
Without this patch, building acs5k_defconfig results in:
drivers/mtd/chips/cfi_cmdset_0002.c: In function 'cfi_amdstd_panic_write':
include/linux/mtd/map.h:331:11: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
drivers/mtd/chips/cfi_cmdset_0002.c: In function 'cfi_amdstd_write_words':
include/linux/mtd/map.h:331:11: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
drivers/mtd/chips/cfi_cmdset_0001.c: In function 'cfi_intelext_write_words':
include/linux/mtd/map.h:331:11: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The diskonchip drivers traditionally use home-grown macros for
doing MMIO accesses, which cause a lot of warnings, at least
on ARM machines:
drivers/mtd/devices/doc2000.c: In function 'doc_write':
drivers/mtd/devices/doc2000.c:854:5: warning: value computed is not used [-Wunused-value]
drivers/mtd/devices/doc2000.c: In function 'doc_erase':
drivers/mtd/devices/doc2000.c:1123:5: warning: value computed is not used [-Wunused-value
drivers/mtd/nand/diskonchip.c: In function 'doc2000_read_byte':
drivers/mtd/nand/diskonchip.c:318:3: warning: value computed is not used [-Wunused-value]
A nicer solution is to use the architecture-defined I/O accessors.
Here, we use the __raw_readl/__raw_writel style, instead of the
proper readl/writel ones, in order to preserve the odd semantics
of the existing macros that have their own barrier implementation
and no byte swap. It would be nice to fix this properly and use
the correct accessors as well as make the word size independent
from the architecture, but I guess the hardware is obsolete
enough that we should better not mess the driver an more than
necessary.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch is an attempt to fix following compilation warning.
In file included from drivers/mtd/chips/cfi_cmdset_0001.c:35:0:
drivers/mtd/chips/cfi_cmdset_0001.c: In function 'cfi_intelext_write_words':
include/linux/mtd/map.h:331:11: warning: 'r.x[0]' may be used uninitialized in this function [-Wmaybe-uninitialized]
I could have used uninitialized_var() too, but didn't used it as the final else
part of map_word_load() is missing. So there is a chance that it might be passed
uninitialized. Better initialize to zero.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add missing colons to fix kernel-doc generation warnings.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The code probes if DMA channels can get allocated and tears them down at
removal/failure if needed.
If available it uses them to transfer the data part (not ECC). On
failure we fall back to PIO mode.
Based on Guennadi Liakhovetski's code from the sh_mmcif driver.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Some small fixes to avoid sparse and smatch complain. Other cosmetic fixes
as well.
- Change of the type of the member index in struct sh_flctl from signed
to unsigned. We use index by addressing array members, so unsigned is more
concise here. Adapt functions relying on sh_flctl::index.
- Remove a blurring cast in write_fiforeg().
- Apply consistent naming scheme when refering to the data buffer.
- Shorten some unnecessarily verbose functions.
- Remove spaces at start of lines.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The whole gpmi-nand driver has turned to pure devicetree supported.
So the linux/mtd/gpmi-nand.h is not neccessary now. Just remove it,
and move some macros to the gpmi-nand driver itself.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Few devices like H27UBG8T2CTR have a writesize/oobsize of 8KB/640B.
This means that the maximum oobsize has gone up to 640 bytes and consequently
the maximum ecc placement locations have also gone up to 640.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource
Switch to devm_request_and_ioremap at the sametime
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The nomadik_nand driver is really just a subset of the FSMC
NAND driver, and there are no users anymore so let's delete
it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Pull networking fixes from David Miller:
"First post-Sandy pull request"
1) Fix antenna gain handling and initialization of chan->max_reg_power
in wireless, from Felix Fietkau.
2) Fix nexthop handling in H.232 conntrack helper, from Julian
Anastasov.
3) Only process 80211 mesh config header in certain kinds of frames,
from Javier Cardona.
4) 80211 management frame header length needs to be validated, from
Johannes Berg.
5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay.
6) Test for permanent state correctly in VXLAN driver, from Stephen
Hemminger.
7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov.
8) Fix off by one errors in bonding, from Nikolay ALeksandrov.
9) Fix divide by zero in TCP-Illinois congestion control. From Jesper
Dangaard Brouer.
10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a
sizeof of a sizeof, so you can size your size" Fix from Julian
Anastasov.
11) Several drivers do mdiobus_free without first doing an
mdiobus_unregister leading to stray pointer references. Fix from
Peter Senna Tschudin.
12) Fix OOPS in l2tp_eth_create() error path, it's another danling
pointer kinda situation. Fix from Tom Parkin.
13) Hardware driven by the vmxnet driver can't handle larger than 16K
fragments, so split them up when necessary. From Eric Dumazet.
14) Handle zero length data length in tcp_send_rcvq() properly. Fix
from Pavel Emelyanov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tcp-repair: Handle zero-length data put in rcv queue
vmxnet3: must split too big fragments
l2tp: fix oops in l2tp_eth_create() error path
cxgb4: Fix unable to get UP event from the LLD
drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
bnx2x: fix HW initialization using fw 7.8.x
tcp: Fix double sizeof in new tcp_metrics code
net: fix divide by zero in tcp algorithm illinois
net: sctp: Fix typo in net/sctp
bonding: fix second off-by-one error
bonding: fix off-by-one error
bnx2x: Disable FCoE for 57840 since not yet supported by FW
bnx2x: Fix no link on 577xx 10G-baseT
bnx2x: Fix unrecognized SFP+ module after driver is loaded
bnx2x: Fix potential incorrect link speed provision
bnx2x: Restore global registers back to default.
bnx2x: Fix link down in 57712 following LFA
bnx2x: Fix 57810 1G-KR link against certain switches.
ixgbe: PTP get_ts_info missing software support
...
This hashtable implementation is using hlist buckets to provide a simple
hashtable to prevent it from getting reimplemented all over the kernel.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
[ Merging this now, so that subsystems can start applying Sasha's
patches that use this - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This contains unexpectedly many changes in a wide range due to the
fixes for races at disconnection of USB audio devices. In the end,
we end up covering fairly core parts of sound subsystem.
Other than that, just a few usual small fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=bxYB
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains unexpectedly many changes in a wide range due to the
fixes for races at disconnection of USB audio devices. In the end, we
end up covering fairly core parts of sound subsystem.
Other than that, just a few usual small fixes."
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: ice1724: Fix rate setup after resume
ALSA: Avoid endless sleep after disconnect
ALSA: Add a reference counter to card instance
ALSA: usb-audio: Fix races at disconnection in mixer_quirks.c
ALSA: usb-audio: Use rwsem for disconnect protection
ALSA: usb-audio: Fix races at disconnection
ALSA: PCM: Fix some races at disconnection
ASoC: omap-dmic: Correct functional clock name
ASoC: zoom2: Fix compile error by including correct header files
ALSA: hda - Fix mute-LED setup for HP dv5 laptop
After commit b3356bf0db (KVM: emulator: optimize "rep ins" handling),
the pieces of io data can be collected and write them to the guest memory
or MMIO together
Unfortunately, kvm splits the mmio access into 8 bytes and store them to
vcpu->mmio_fragments. If the guest uses "rep ins" to move large data, it
will cause vcpu->mmio_fragments overflow
The bug can be exposed by isapc (-M isapc):
[23154.818733] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
[ ......]
[23154.858083] Call Trace:
[23154.859874] [<ffffffffa04f0e17>] kvm_get_cr8+0x1d/0x28 [kvm]
[23154.861677] [<ffffffffa04fa6d4>] kvm_arch_vcpu_ioctl_run+0xcda/0xe45 [kvm]
[23154.863604] [<ffffffffa04f5a1a>] ? kvm_arch_vcpu_load+0x17b/0x180 [kvm]
Actually, we can use one mmio_fragment to store a large mmio access then
split it when we pass the mmio-exit-info to userspace. After that, we only
need two entries to store mmio info for the cross-mmio pages access
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
As Mukesh explained it, the MMUEXT_TLB_FLUSH_ALL allows the
hypervisor to do a TLB flush on all active vCPUs. If instead
we were using the generic one (which ends up being xen_flush_tlb)
we end up making the MMUEXT_TLB_FLUSH_LOCAL hypercall. But
before we make that hypercall the kernel will IPI all of the
vCPUs (even those that were asleep from the hypervisor
perspective). The end result is that we needlessly wake them
up and do a TLB flush when we can just let the hypervisor
do it correctly.
This patch gives around 50% speed improvement when migrating
idle guest's from one host to another.
Oracle-bug: 14630170
CC: stable@vger.kernel.org
Tested-by: Jingjie Jiang <jingjie.jiang@oracle.com>
Suggested-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
- one recently introduced crash for dm-raid10 with discard
- one bug in new functionality that has been around for a few releases.
- minor bug in md's 'faulty' personality
and UAPI disintegration for md.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=plEs
-----END PGP SIGNATURE-----
Merge tag 'md-3.7-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"Some fixes for md in 3.7
- one recently introduced crash for dm-raid10 with discard
- one bug in new functionality that has been around for a few
releases.
- minor bug in md's 'faulty' personality
and UAPI disintegration for md."
* tag 'md-3.7-fixes' of git://neil.brown.name/md:
MD RAID10: Fix oops when creating RAID10 arrays via dm-raid.c
md/raid1: Fix assembling of arrays containing Replacements.
md faulty: use disk_stack_limits()
UAPI: (Scripted) Disintegrate include/linux/raid
For more strict protection for wild disconnections, a refcount is
introduced to the card instance, and let it up/down when an object is
referred via snd_lookup_*() in the open ops.
The free-after-last-close check is also changed to check this refcount
instead of the empty list, too.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use rcu_read_lock_sched / rcu_read_unlock_sched / synchronize_sched
instead of rcu_read_lock / rcu_read_unlock / synchronize_rcu.
This is an optimization. The RCU-protected region is very small, so
there will be no latency problems if we disable preempt in this region.
So we use rcu_read_lock_sched / rcu_read_unlock_sched that translates
to preempt_disable / preempt_disable. It is smaller (and supposedly
faster) than preemptible rcu_read_lock / rcu_read_unlock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces new barrier pair light_mb() and heavy_mb() for
percpu rw semaphores.
This patch fixes a bug in percpu-rw-semaphores where a barrier was
missing in percpu_up_write.
This patch improves performance on the read path of
percpu-rw-semaphores: on non-x86 cpus, there was a smp_mb() in
percpu_up_read. This patch changes it to a compiler barrier and removes
the "#if defined(X86) ..." condition.
From: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
A number of places in the mesh code don't check that
the frame data is present and in the skb header when
trying to access. Add those checks and the necessary
pskb_may_pull() calls. This prevents accessing data
that doesn't actually exist.
To do this, export ieee80211_get_mesh_hdrlen() to be
able to use it in mac80211.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here are some staging driver fixes for your 3.7-rc tree.
Nothing major here, a number of iio driver fixups that were causing problems,
some comedi driver bugfixes, and a bunch of tidspbridge warning squashing and
other regressions fixed from the 3.6 release.
All have been in the linux-next releases for a bit.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCKvy4ACgkQMUfUDdst+yniwwCeLlAdaExLLMLzLEYncTnQeR7c
TYkAmwbUClssHQ+CjDny4LqvJ8h8z2Et
=1wfZ
-----END PGP SIGNATURE-----
Merge tag 'staging-3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg Kroah-Hartman:
"Here are some staging driver fixes for your 3.7-rc tree.
Nothing major here, a number of iio driver fixups that were causing
problems, some comedi driver bugfixes, and a bunch of tidspbridge
warning squashing and other regressions fixed from the 3.6 release.
All have been in the linux-next releases for a bit.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (32 commits)
staging: tidspbridge: delete unused mmu functions
staging: tidspbridge: ioremap physical address of the stack segment in shm
staging: tidspbridge: ioremap dsp sync addr
staging: tidspbridge: change type to __iomem for per and core addresses
staging: tidspbridge: drop const from custom mmu implementation
staging: tidspbridge: request the right irq for mmu
staging: ipack: add missing include (implicit declaration of function 'kfree')
staging: ramster: depends on NET
staging: omapdrm: fix allocation size for page addresses array
staging: zram: Fix handling of incompressible pages
Staging: android: binder: Allow using highmem for binder buffers
Staging: android: binder: Fix memory leak on thread/process exit
staging: comedi: ni_labpc: fix possible NULL deref during detach
staging: comedi: das08: fix possible NULL deref during detach
staging: comedi: amplc_pc263: fix possible NULL deref during detach
staging: comedi: amplc_pc236: fix possible NULL deref during detach
staging: comedi: amplc_pc236: fix invalid register access during detach
staging: comedi: amplc_dio200: fix possible NULL deref during detach
staging: comedi: 8255_pci: fix possible NULL deref during detach
staging: comedi: ni_daq_700: fix dio subdevice regression
...
Here are a number of firmware core fixes for 3.7, and some other minor fixes.
And some documentation updates thrown in for good measure.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCKwkIACgkQMUfUDdst+ynzUgCfQDwxUw1PVqQyWy7SakpsjFJJ
8kwAoITyjppn39v1WuZbg0+FZ6JpocyY
=2mDG
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are a number of firmware core fixes for 3.7, and some other minor
fixes. And some documentation updates thrown in for good measure.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation:Chinese translation of Documentation/arm64/memory.txt
Documentation:Chinese translation of Documentation/arm64/booting.txt
Documentation:Chinese translation of Documentation/IRQ.txt
firmware loader: document kernel direct loading
sysfs: sysfs_pathname/sysfs_add_one: Use strlcat() instead of strcat()
dynamic_debug: Remove unnecessary __used
firmware loader: sync firmware cache by async_synchronize_full_domain
firmware loader: let direct loading back on 'firmware_buf'
firmware loader: fix one reqeust_firmware race
firmware loader: cancel uncache work before caching firmware
Here are some driver fixes for 3.7. They include extcon driver fixes, a
hyper-v bugfix, and two other minor driver fixes.
All of these have been in the linux-next releases for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCKwS8ACgkQMUfUDdst+ylZPACgyfOBcNVdzCkoUGrFjfUbpmxx
iNoAn1Oc3CAFrYzly1lNSNA/G9qXTXsg
=3+hj
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are some driver fixes for 3.7. They include extcon driver fixes,
a hyper-v bugfix, and two other minor driver fixes.
All of these have been in the linux-next releases for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
sonypi: suspend/resume callbacks should be conditionally compiled on CONFIG_PM_SLEEP
Drivers: hv: Cleanup error handling in vmbus_open()
extcon : register for cable interest by cable name
extcon: trivial: kfree missed from remove path
extcon: driver model release call not needed
extcon: MAX77693: Add platform data for MUIC device to initialize registers
extcon: max77693: Use max77693_update_reg for rmw operations
extcon: Fix kerneldoc for extcon_set_cable_state and extcon_set_cable_state_
extcon: adc-jack: Add missing MODULE_LICENSE
extcon: adc-jack: Fix checking return value of request_any_context_irq
extcon: Fix return value in extcon_register_interest()
extcon: unregister compat link on cleanup
extcon: Unregister compat class at module unload to fix oops
extcon: optimising the check_mutually_exclusive function
extcon: standard cable names definition and declaration changed
extcon-max8997: remove usage of ret in max8997_muic_handle_charger_type_detach
extcon: Remove duplicate inclusion of extcon.h header file
Pull x86 fixes from Ingo Molnar:
"This fixes a couple of nasty page table initialization bugs which were
causing kdump regressions. A clean rearchitecturing of the code is in
the works - meanwhile these are reverts that restore the
best-known-working state of the kernel.
There's also EFI fixes and other small fixes."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mm: Undo incorrect revert in arch/x86/mm/init.c
x86: efi: Turn off efi_enabled after setup on mixed fw/kernel
x86, mm: Find_early_table_space based on ranges that are actually being mapped
x86, mm: Use memblock memory loop instead of e820_RAM
x86, mm: Trim memory in memblock to be page aligned
x86/irq/ioapic: Check for valid irq_cfg pointer in smp_irq_move_cleanup_interrupt
x86/efi: Fix oops caused by incorrect set_memory_uc() usage
x86-64: Fix page table accounting
Revert "x86/mm: Fix the size calculation of mapping tables"
MAINTAINERS: Add EFI git repository location
Pull perf fixes from Ingo Molnar:
"Most of the kernel diffstat relates to a group of Intel P6 and KNC
(Xeon-Phi Knights Corner) PMU driver fixes, neither of which is in
heavy use, so we took the fixes.
The rest is diverse smallish fixes to the tooling and kernel side."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Remove unused variable in nhmex_rbox_alter_er()
perf/x86: Enable overflow on Intel KNC with a custom knc_pmu_handle_irq()
perf/x86: Remove cpuc->enable check on Intl KNC event enable/disable
perf/x86: Make Intel KNC use full 40-bit width of counters
perf/x86/uncore: Handle pci_read_config_dword() errors
perf/x86: Remove P6 cpuc->enabled check
perf/x86: Update/fix generic events on P6 PMU
perf/x86: Fix P6 FP_ASSIST event constraint
perf, cpu hotplug: Use cached value of smp_processor_id()
perf, cpu hotplug: Run CPU_STARTING notifiers with irqs disabled
x86/perf: Fix virtualization sanity check
perf test: Fix exclude_guest parse events tests
perf tools: do not flush maps on COMM for perf report
perf help: Fix --help for builtins
perf trace: Check if sample raw_data field is set
perf trace: Validate syscall id before growing syscall table
Pull drm radeon fixes from Dave Airlie:
"Just radeon fixes in this one:
- some new PCI IDs
- ATPX regression fix
- async VM regression fixes
- some module options fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix ATPX regression in acpi rework
drm/radeon: fix ATPX function documentation
drm/radeon: move the retry to gem_object_create
drm/radeon: move size limits to gem_object_create.
drm/radeon: use vzalloc for gart pages
drm/radeon: fix and simplify pot argument checks v3
drm/radeon: fix header size estimation in VM code
drm/radeon: remove set_page check from VM code
drm/radeon: fix si_set_page v2
drm/radeon: fix cayman_vm_set_page v2
drm/radeon: fix PFP sync in vm_flush
drm/radeon: add error output if VM CS fails on cayman
drm/radeon: give each backlight a unique id
drm/radeon: fix sparse warning
drm/radeon: add some new SI PCI ids
rb_erase_augmented() is a static function annotated with
__always_inline. This causes a compile failure when attempting to use
the rbtree implementation as a library (e.g. kvm tool):
rbtree_augmented.h:125:24: error: expected `=', `,', `;', `asm' or `__attribute__' before `void'
Include linux/compiler.h in rbtree_augmented.h so that the __always_inline
macro is resolved correctly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A bunch of fixes here, mostly minor except for the pl022 which has just
been a bit of a shambles all round, the recent runtime PM changes have
as far as I can tell never worked so they're just getting thrown out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=9XvI
-----END PGP SIGNATURE-----
Merge tag 'spi-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi fixes from Mark Brown:
"A bunch of fixes here, mostly minor except for the pl022 which has
just been a bit of a shambles all round, the recent runtime PM changes
have as far as I can tell never worked so they're just getting thrown
out."
* tag 'spi-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/pl022: Revert recent runtime PM changes
spi: tsc2005: delete soon-obsolete e-mail address
spi: spi-rspi: fix build error for the latest shdma driver
We will not map partial pages, so need to make sure memblock
allocation will not allocate those bytes out.
Also we will use for_each_mem_pfn_range() to loop to map memory
range to keep them consistent.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQVZirvaBMFYRfXMmWEcHbKSicQEHz4VAwUv0xFCk51ZNw@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
* Fix mysterious SIGSEGV or SIGKILL in applications due to corrupting
of the %eip when returning from a signal handler.
* Fix various ARM compile issues after the merge fallout.
* Continue on making more of the Xen generic code usable by ARM platform.
* Fix SR-IOV passthrough to mirror multifunction PCI devices.
* Fix various compile warnings.
* Remove hypercalls that don't exist anymore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQhsIHAAoJEFjIrFwIi8fJ9LsH+gLGiF7dvFIUw1IA/Ev+tZ9Y
YFFMJwmP71ZoqrJnEH+0vXlDU7YQAF/qQysVfACfHU5en2OEO24IuINddrm3wcYU
2YAwEiLQstWhK1bhYqRqWeczjR3BV0NWtUoHpQar/5h4Ykppl5OxmXdBEfv+ThzA
ju2d9fvQoJR7flW/CsWqoNcyPubzzXWYRCBWLdChw3NXVQTr/5ZDwvkIwgk6Gv5g
vR0Qlirjdf2IyyE77zYhZw61H82IXoVCKnmif3HC1lYnSvVdVxamI0UhtXIjPJQU
KB2e9Qkfix8weXDtpNBqa/VUIW7R83qCTZszs4mD/ktPAhgvxzCF3h/XLLXuwS4=
=FR/L
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen bug-fixes from Konrad Rzeszutek Wilk:
- Fix mysterious SIGSEGV or SIGKILL in applications due to corrupting
of the %eip when returning from a signal handler.
- Fix various ARM compile issues after the merge fallout.
- Continue on making more of the Xen generic code usable by ARM
platform.
- Fix SR-IOV passthrough to mirror multifunction PCI devices.
- Fix various compile warnings.
- Remove hypercalls that don't exist anymore.
* tag 'stable/for-linus-3.7-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: dbgp: Fix warning when CONFIG_PCI is not enabled.
xen: arm: comment on why 64-bit xen_pfn_t is safe even on 32 bit
xen: balloon: use correct type for frame_list
xen/x86: don't corrupt %eip when returning from a signal handler
xen: arm: make p2m operations NOPs
xen: balloon: don't include e820.h
xen: grant: use xen_pfn_t type for frame_list.
xen: events: pirq_check_eoi_map is X86 specific
xen: XENMEM_translate_gpfn_list was remove ages ago and is unused.
xen: sysfs: fix build warning.
xen: sysfs: include err.h for PTR_ERR etc
xen: xenbus: quirk uses x86 specific cpuid
xen PV passthru: assign SR-IOV virtual functions to separate virtual slots
xen/xenbus: Fix compile warning.
xen/x86: remove duplicated include from enlighten.c
This patch add platform data for MUIC device to initialize register
on probe() call because it should unmask interrupt mask register
and initialize some register related to MUIC device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Add a bit TCPI_OPT_SYN_DATA (32) to the socket option TCP_INFO:tcpi_options.
It's set if the data in SYN (sent or received) is acked by SYN-ACK. Server or
client application can use this information to check Fast Open success rate.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this change now individual drivers can use standard cable
names as below:
static const char *arizona_cable[] = {
extcon_cable_name[EXTCON_USB],
extcon_cable_name[EXTCON_USB_HOST],
"CUSTOM_CABLE"
NULL,
}
Signed-off-by: anish kumar <anish198519851985@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Merge misc fixes from Andrew Morton:
"Seven fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (7 patches)
lib/dma-debug.c: fix __hash_bucket_find()
mm: compaction: correct the nr_strict va isolated check for CMA
firmware/memmap: avoid type conflicts with the generic memmap_init()
pidns: remove recursion from free_pid_ns()
drivers/video/backlight/lm3639_bl.c: return proper error in lm3639_bled_mode_store() error paths
kernel/sys.c: fix stack memory content leak via UNAME26
linux/coredump.h needs asm/siginfo.h
free_pid_ns() operates in a recursive fashion:
free_pid_ns(parent)
put_pid_ns(parent)
kref_put(&ns->kref, free_pid_ns);
free_pid_ns
thus if there was a huge nesting of namespaces the userspace may trigger
avalanche calling of free_pid_ns leading to kernel stack exhausting and a
panic eventually.
This patch turns the recursion into an iterative loop.
Based on a patch by Andrew Vagin.
[akpm@linux-foundation.org: export put_pid_ns() to modules]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5ab1c309b3 ("coredump: pass siginfo_t* to do_coredump() and
below, not merely signr") added siginfo_t to linux/coredump.h but forgot
to include asm/siginfo.h. This breaks the build for UML/i386. (And any
other arch where asm/siginfo.h is not magically preincluded...)
In file included from arch/x86/um/elfcore.c:2:0: include/linux/coredump.h:15:25: error: unknown type name 'siginfo_t'
make[1]: *** [arch/x86/um/elfcore.o] Error 1
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: "Jonathan M. Foote" <jmfoote@cert.org>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* commit 'v3.7-rc1': (10892 commits)
Linux 3.7-rc1
x86, boot: Explicitly include autoconf.h for hostprogs
perf: Fix UAPI fallout
ARM: config: make sure that platforms are ordered by option string
ARM: config: sort select statements alphanumerically
UAPI: (Scripted) Disintegrate include/linux/byteorder
UAPI: (Scripted) Disintegrate include/linux
UAPI: Unexport linux/blk_types.h
UAPI: Unexport part of linux/ppp-comp.h
perf: Handle new rbtree implementation
procfs: don't need a PATH_MAX allocation to hold a string representation of an int
vfs: embed struct filename inside of names_cache allocation if possible
audit: make audit_inode take struct filename
vfs: make path_openat take a struct filename pointer
vfs: turn do_path_lookup into wrapper around struct filename variant
audit: allow audit code to satisfy getname requests from its names_list
vfs: define struct filename and have getname() return it
btrfs: Fix compilation with user namespace support enabled
userns: Fix posix_acl_file_xattr_userns gid conversion
userns: Properly print bluetooth socket uids
...