The IRQ_EXIT_OFFSET trick was used to make sure the irq
doesn't get preempted after we substract the HARDIRQ_OFFSET
until we are entirely done with any code in irq_exit().
This workaround was necessary because some archs may call
irq_exit() with irqs enabled and there is still some code
in the end of this function that is not covered by the
HARDIRQ_OFFSET but want to stay non-preemptible.
Now that irq are always disabled in irq_exit(), the whole code
is guaranteed not to be preempted. We can thus remove this hack.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
With the irq protection in irq_exit, we can remove the #ifdeffery and
the bh_disable/enable dance in invoke_softirq()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1302202155320.22263@ionos
We had already a few problems with code called from irq_exit() when
interrupted from a nesting interrupt. This can happen on architectures
which do not define __ARCH_IRQ_EXIT_IRQS_DISABLED.
__ARCH_IRQ_EXIT_IRQS_DISABLED should go away and we want to make it
mandatory to call irq_exit() with interrupts disabled.
As a temporary protection disable interrupts for those architectures
which do not define __ARCH_IRQ_EXIT_IRQS_DISABLED and add a WARN_ONCE
when an architecture which defines __ARCH_IRQ_EXIT_IRQS_DISABLED calls
irq_exit() with interrupts enabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1302202155320.22263@ionos
Pull networking update from David Miller:
1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
timestamp offset. From Andrey Vagin.
2) VMWARE VM VSOCK layer, from Andy King.
3) Much improved support for virtual functions and SR-IOV in bnx2x,
from Ariel ELior.
4) All protocols on ipv4 and ipv6 are now network namespace aware, and
all the compatability checks for initial-namespace-only protocols is
removed. Thanks to Tom Parkin for helping deal with the last major
holdout, L2TP.
5) IPV6 support in netpoll and network namespace support in pktgen,
from Cong Wang.
6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
Protocol (MVRP) support, from David Ward.
7) Compute packet lengths more accurately in the packet scheduler, from
Eric Dumazet.
8) Use per-task page fragment allocator in skb_append_datato_frags(),
also from Eric Dumazet.
9) Add support for connection tracking labels in netfilter, from
Florian Westphal.
10) Fix default multicast group joining on ipv6, and add anti-spoofing
checks to 6to4 and 6rd. From Hannes Frederic Sowa.
11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
times, rearrange inet frag datastructures for better cacheline
locality, and move more operations outside of locking. From Jesper
Dangaard Brouer.
12) Instead of strict master <--> slave relationships, allow arbitrary
scenerios with "upper device lists". From Jiri Pirko.
13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
Pirko.
14) Add a BPF filter netfilter match target, from Willem de Bruijn.
15) Orphan and delete a bunch of pre-historic networking drivers from
Paul Gortmaker.
16) Add TSO support for GRE tunnels, from Pravin B SHelar. Although
this still needs some minor bug fixing before it's %100 correct in
all cases.
17) Handle unresolved IPSEC states like ARP, with a resolution packet
queue. From Steffen Klassert.
18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
Hemminger. This was long overdue.
19) Support SO_REUSEPORT, from Tom Herbert.
20) Allow locking a socket BPF filter, so that it cannot change after a
process drops capabilities.
21) Add VLAN filtering to bridge, from Vlad Yasevich.
22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
the ipv6 routes, from YOSHIFUJI Hideaki.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
ipv6: fix race condition regarding dst->expires and dst->from.
net: fix a wrong assignment in skb_split()
ip_gre: remove an extra dst_release()
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
atl1c: restore buffer state
net: fix a build failure when !CONFIG_PROC_FS
net: ipv4: fix waring -Wunused-variable
net: proc: fix build failed when procfs is not configured
Revert "xen: netback: remove redundant xenvif_put"
net: move procfs code to net/core/net-procfs.c
qmi_wwan, cdc-ether: add ADU960S
bonding: set sysfs device_type to 'bond'
bonding: fix bond_release_all inconsistencies
b44: use netdev_alloc_skb_ip_align()
xen: netback: remove redundant xenvif_put
net: fec: Do a sanity check on the gpio number
ip_gre: propogate target device GSO capability to the tunnel device
ip_gre: allow CSUM capable devices to handle packets
bonding: Fix initialize after use for 3ad machine state spinlock
bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
...
While remotely reading the cputime of a task running in a
full dynticks CPU, the values stored in utime/stime fields
of struct task_struct may be stale. Its values may be those
of the last kernel <-> user transition time snapshot and
we need to add the tickless time spent since this snapshot.
To fix this, flush the cputime of the dynticks CPUs on
kernel <-> user transition and record the time / context
where we did this. Then on top of this snapshot and the current
time, perform the fixup on the reader side from task_times()
accessors.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
[fixed kvm module related build errors]
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
In various network workloads, __do_softirq() latencies can be up
to 20 ms if HZ=1000, and 200 ms if HZ=100.
This is because we iterate 10 times in the softirq dispatcher,
and some actions can consume a lot of cycles.
This patch changes the fallback to ksoftirqd condition to :
- A time limit of 2 ms.
- need_resched() being set on current task
When one of this condition is met, we wakeup ksoftirqd for further
softirq processing if we still have pending softirqs.
Using need_resched() as the only condition can trigger RCU stalls,
as we can keep BH disabled for too long.
I ran several benchmarks and got no significant difference in
throughput, but a very significant reduction of latencies (one order
of magnitude) :
In following bench, 200 antagonist "netperf -t TCP_RR" are started in
background, using all available cpus.
Then we start one "netperf -t TCP_RR", bound to the cpu handling the NIC
IRQ (hard+soft)
Before patch :
# netperf -H 7.7.7.84 -t TCP_RR -T2,2 -- -k
RT_LATENCY,MIN_LATENCY,MAX_LATENCY,P50_LATENCY,P90_LATENCY,P99_LATENCY,MEAN_LATENCY,STDDEV_LATENCY
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET
to 7.7.7.84 () port 0 AF_INET : first burst 0 : cpu bind
RT_LATENCY=550110.424
MIN_LATENCY=146858
MAX_LATENCY=997109
P50_LATENCY=305000
P90_LATENCY=550000
P99_LATENCY=710000
MEAN_LATENCY=376989.12
STDDEV_LATENCY=184046.92
After patch :
# netperf -H 7.7.7.84 -t TCP_RR -T2,2 -- -k
RT_LATENCY,MIN_LATENCY,MAX_LATENCY,P50_LATENCY,P90_LATENCY,P99_LATENCY,MEAN_LATENCY,STDDEV_LATENCY
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET
to 7.7.7.84 () port 0 AF_INET : first burst 0 : cpu bind
RT_LATENCY=40545.492
MIN_LATENCY=9834
MAX_LATENCY=78366
P50_LATENCY=33583
P90_LATENCY=59000
P99_LATENCY=69000
MEAN_LATENCY=38364.67
STDDEV_LATENCY=12865.26
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Miller <davem@davemloft.net>
Cc: Tom Herbert <therbert@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_VIRT_CPU_ACCOUNTING, when vtime_account()
is called in irq entry/exit, we perform a check on the
context: if we are interrupting the idle task we
account the pending cputime to idle, otherwise account
to system time or its sub-areas: tsk->stime, hardirq time,
softirq time, ...
However this check for idle only concerns the hardirq entry
and softirq entry:
* Hardirq may directly interrupt the idle task, in which case
we need to flush the pending CPU time to idle.
* The idle task may be directly interrupted by a softirq if
it calls local_bh_enable(). There is probably no such call
in any idle task but we need to cover every case. Ksoftirqd
is not concerned because the idle time is flushed on context
switch and softirq in the end of hardirq have the idle time
already flushed from the hardirq entry.
In the other cases we always account to system/irq time:
* On hardirq exit we account the time to hardirq time.
* On softirq exit we account the time to softirq time.
To optimize this and avoid the indirect call to vtime_account()
and the checks it performs, specialize the vtime irq APIs and
only perform the check on irq entry. Irq exit can directly call
vtime_account_system().
CONFIG_IRQ_TIME_ACCOUNTING behaviour doesn't change and directly
maps to its own vtime_account() implementation. One may want
to take benefits from the new APIs to optimize irq time accounting
as well in the future.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull scheduler changes from Ingo Molnar:
"Continued quest to clean up and enhance the cputime code by Frederic
Weisbecker, in preparation for future tickless kernel features.
Other than that, smallish changes."
Fix up trivial conflicts due to additions next to each other in arch/{x86/}Kconfig
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
cputime: Make finegrained irqtime accounting generally available
cputime: Gather time/stats accounting config options into a single menu
ia64: Reuse system and user vtime accounting functions on task switch
ia64: Consolidate user vtime accounting
vtime: Consolidate system/idle context detection
cputime: Use a proper subsystem naming for vtime related APIs
sched: cpu_power: enable ARCH_POWER
sched/nohz: Clean up select_nohz_load_balancer()
sched: Fix load avg vs. cpu-hotplug
sched: Remove __ARCH_WANT_INTERRUPTS_ON_CTXSW
sched: Fix nohz_idle_balance()
sched: Remove useless code in yield_to()
sched: Add time unit suffix to sched sysctl knobs
sched/debug: Limit sd->*_idx range on sysctl
sched: Remove AFFINE_WAKEUPS feature flag
s390: Remove leftover account_tick_vtime() header
cputime: Consolidate vtime handling on context switch
sched: Move cputime code to its own file
cputime: Generalize CONFIG_VIRT_CPU_ACCOUNTING
tile: Remove SD_PREFER_LOCAL leftover
...
Use a naming based on vtime as a prefix for virtual based
cputime accounting APIs:
- account_system_vtime() -> vtime_account()
- account_switch_vtime() -> vtime_task_switch()
It makes it easier to allow for further declension such
as vtime_account_system(), vtime_account_idle(), ... if we
want to find out the context we account to from generic code.
This also make it better to know on which subsystem these APIs
refer to.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
[ paulmck: Call rcu_note_context_switch() with interrupts enabled. ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/20120716103948.456416747@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is needed to allow network softirq packet processing to make use of
PF_MEMALLOC.
Currently softirq context cannot use PF_MEMALLOC due to it not being
associated with a task, and therefore not having task flags to fiddle with
- thus the gfp to alloc flag mapping ignores the task flags when in
interrupts (hard or soft) context.
Allowing softirqs to make use of PF_MEMALLOC therefore requires some
trickery. This patch borrows the task flags from whatever process happens
to be preempted by the softirq. It then modifies the gfp to alloc flags
mapping to not exclude task flags in softirq context, and modify the
softirq code to save, clear and restore the PF_MEMALLOC flag.
The save and clear, ensures the preempted task's PF_MEMALLOC flag doesn't
leak into the softirq. The restore ensures a softirq's PF_MEMALLOC flag
cannot leak back into the preempted process. This should be safe due to
the following reasons
Softirqs can run on multiple CPUs sure but the same task should not be
executing the same softirq code. Neither should the softirq
handler be preempted by any other softirq handler so the flags
should not leak to an unrelated softirq.
Softirqs re-enable hardware interrupts in __do_softirq() so can be
preempted by hardware interrupts so PF_MEMALLOC is inherited
by the hard IRQ. However, this is similar to a process in
reclaim being preempted by a hardirq. While PF_MEMALLOC is
set, gfp_to_alloc_flags() distinguishes between hard and
soft irqs and avoids giving a hardirq the ALLOC_NO_WATERMARKS
flag.
If the softirq is deferred to ksoftirq then its flags may be used
instead of a normal tasks but as the softirq cannot be preempted,
the PF_MEMALLOC flag does not leak to other code by accident.
[davem@davemloft.net: Document why PF_MEMALLOC is safe]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: David Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer changes for v3.4 from Ingo Molnar
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
ntp: Fix integer overflow when setting time
math: Introduce div64_long
cs5535-clockevt: Allow the MFGPT IRQ to be shared
cs5535-clockevt: Don't ignore MFGPT on SMP-capable kernels
x86/time: Eliminate unused irq0_irqs counter
clocksource: scx200_hrt: Fix the build
x86/tsc: Reduce the TSC sync check time for core-siblings
timer: Fix bad idle check on irq entry
nohz: Remove ts->Einidle checks before restarting the tick
nohz: Remove update_ts_time_stat from tick_nohz_start_idle
clockevents: Leave the broadcast device in shutdown mode when not needed
clocksource: Load the ACPI PM clocksource asynchronously
clocksource: scx200_hrt: Convert scx200 to use clocksource_register_hz
clocksource: Get rid of clocksource_calc_mult_shift()
clocksource: dbx500: convert to clocksource_register_hz()
clocksource: scx200_hrt: use pr_<level> instead of printk
time: Move common updates to a function
time: Reorder so the hot data is together
time: Remove most of xtime_lock usage in timekeeping.c
ntp: Add ntp_lock to replace xtime_locking
...
Pull scheduler changes for v3.4 from Ingo Molnar
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
printk: Make it compile with !CONFIG_PRINTK
sched/x86: Fix overflow in cyc2ns_offset
sched: Fix nohz load accounting -- again!
sched: Update yield() docs
printk/sched: Introduce special printk_sched() for those awkward moments
sched/nohz: Correctly initialize 'next_balance' in 'nohz' idle balancer
sched: Cleanup cpu_active madness
sched: Fix load-balance wreckage
sched: Clean up parameter passing of proc_sched_autogroup_set_nice()
sched: Ditch per cgroup task lists for load-balancing
sched: Rename load-balancing fields
sched: Move load-balancing arguments into helper struct
sched/rt: Do not submit new work when PI-blocked
sched/rt: Prevent idle task boosting
sched/wait: Add __wake_up_all_locked() API
sched/rt: Document scheduler related skip-resched-check sites
sched/rt: Use schedule_preempt_disabled()
sched/rt: Add schedule_preempt_disabled()
sched/rt: Do not throttle when PI boosting
sched/rt: Keep period timer ticking when rt throttling is active
...
Pull perf events changes for v3.4 from Ingo Molnar:
- New "hardware based branch profiling" feature both on the kernel and
the tooling side, on CPUs that support it. (modern x86 Intel CPUs
with the 'LBR' hardware feature currently.)
This new feature is basically a sophisticated 'magnifying glass' for
branch execution - something that is pretty difficult to extract from
regular, function histogram centric profiles.
The simplest mode is activated via 'perf record -b', and the result
looks like this in perf report:
$ perf record -b any_call,u -e cycles:u branchy
$ perf report -b --sort=symbol
52.34% [.] main [.] f1
24.04% [.] f1 [.] f3
23.60% [.] f1 [.] f2
0.01% [k] _IO_new_file_xsputn [k] _IO_file_overflow
0.01% [k] _IO_vfprintf_internal [k] _IO_new_file_xsputn
0.01% [k] _IO_vfprintf_internal [k] strchrnul
0.01% [k] __printf [k] _IO_vfprintf_internal
0.01% [k] main [k] __printf
This output shows from/to branch columns and shows the highest
percentage (from,to) jump combinations - i.e. the most likely taken
branches in the system. "branches" can also include function calls
and any other synchronous and asynchronous transitions of the
instruction pointer that are not 'next instruction' - such as system
calls, traps, interrupts, etc.
This feature comes with (hopefully intuitive) flat ascii and TUI
support in perf report.
- Various 'perf annotate' visual improvements for us assembly junkies.
It will now recognize function calls in the TUI and by hitting enter
you can follow the call (recursively) and back, amongst other
improvements.
- Multiple threads/processes recording support in perf record, perf
stat, perf top - which is activated via a comma-list of PIDs:
perf top -p 21483,21485
perf stat -p 21483,21485 -ddd
perf record -p 21483,21485
- Support for per UID views, via the --uid paramter to perf top, perf
report, etc. For example 'perf top --uid mingo' will only show the
tasks that I am running, excluding other users, root, etc.
- Jump label restructurings and improvements - this includes the
factoring out of the (hopefully much clearer) include/linux/static_key.h
generic facility:
struct static_key key = STATIC_KEY_INIT_FALSE;
...
if (static_key_false(&key))
do unlikely code
else
do likely code
...
static_key_slow_inc();
...
static_key_slow_inc();
...
The static_key_false() branch will be generated into the code with as
little impact to the likely code path as possible. the
static_key_slow_*() APIs flip the branch via live kernel code patching.
This facility can now be used more widely within the kernel to
micro-optimize hot branches whose likelihood matches the static-key
usage and fast/slow cost patterns.
- SW function tracer improvements: perf support and filtering support.
- Various hardenings of the perf.data ABI, to make older perf.data's
smoother on newer tool versions, to make new features integrate more
smoothly, to support cross-endian recording/analyzing workflows
better, etc.
- Restructuring of the kprobes code, the splitting out of 'optprobes',
and a corner case bugfix.
- Allow the tracing of kernel console output (printk).
- Improvements/fixes to user-space RDPMC support, allowing user-space
self-profiling code to extract PMU counts without performing any
system calls, while playing nice with the kernel side.
- 'perf bench' improvements
- ... and lots of internal restructurings, cleanups and fixes that made
these features possible. And, as usual this list is incomplete as
there were also lots of other improvements
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (120 commits)
perf report: Fix annotate double quit issue in branch view mode
perf report: Remove duplicate annotate choice in branch view mode
perf/x86: Prettify pmu config literals
perf report: Enable TUI in branch view mode
perf report: Auto-detect branch stack sampling mode
perf record: Add HEADER_BRANCH_STACK tag
perf record: Provide default branch stack sampling mode option
perf tools: Make perf able to read files from older ABIs
perf tools: Fix ABI compatibility bug in print_event_desc()
perf tools: Enable reading of perf.data files from different ABI rev
perf: Add ABI reference sizes
perf report: Add support for taken branch sampling
perf record: Add support for sampling taken branch
perf tools: Add code to support PERF_SAMPLE_BRANCH_STACK
x86/kprobes: Split out optprobe related code to kprobes-opt.c
x86/kprobes: Fix a bug which can modify kernel code permanently
x86/kprobes: Fix instruction recovery on optimized path
perf: Add callback to flush branch_stack on context switch
perf: Disable PERF_SAMPLE_BRANCH_* when not supported
perf/x86: Add LBR software filter support for Intel CPUs
...
The two invoke_softirq() variants are identical except for a single
line. So move the #ifdef __ARCH_IRQ_EXIT_IRQS_DISABLED inside one of
the functions and get rid of the other one.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Create a distinction between scheduler related preempt_enable_no_resched()
calls and the nearly one hundred other places in the kernel that do not
want to reschedule, for one reason or another.
This distinction matters for -rt, where the scheduler and the non-scheduler
preempt models (and checks) are different. For upstream it's purely
documentational.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/n/tip-gs88fvx2mdv5psnzxnv575ke@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
idle_cpu() is called on irq entry to guess if we need to call
tick_check_idle(). This way we can catch up with jiffies if the tick
was stopped, stop accounting idle time during the interrupt and
maintain the sched clock if it is unstable.
But if we are going to exit the idle loop to schedule a new task (ie:
if we have a task in the runqueue or a remotely enqueued ttwu to
perform), the idle_cpu() check will return 0 such that we miss the
call to tick_check_idle() for all interrupts happening before we
schedule the new task.
As a result these interrupts and the softirqs coming along may deal
with stale jiffies values, bad sched clock values, and won't substract
their time from the idle time accounting.
Fix this with using is_idle_task() instead that strictly checks that
we are running the idle task, without caring about the fact we are
going to schedule a task soon.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Link: http://lkml.kernel.org/r/1327427984-23282-3-git-send-email-fweisbec@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The __raise_softirq_irqoff() contains a tracepoint. As tracepoints in headers
can cause issues, and not to mention, bloats the kernel when they are
in a static inline, it is best to move the function that contains the
tracepoint out of the header and into softirq.c.
Link: http://lkml.kernel.org/r/20120118120711.GB14863@elte.hu
Suggested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:
- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.
There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.
Split this function into:
- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.
- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).
To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().
This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The changed files were only including linux/module.h for the
EXPORT_SYMBOL infrastructure, and nothing else. Revector them
onto the isolated export header for faster compile times.
Nothing to see here but a whole lot of instances of:
-#include <linux/module.h>
+#include <linux/export.h>
This commit is only changing the kernel dir; next targets
will probably be mm, fs, the arch dirs, etc.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The rcu_read_unlock_special() function relies on in_irq() to exclude
scheduler activity from interrupt level. This fails because exit_irq()
can invoke the scheduler after clearing the preempt_count() bits that
in_irq() uses to determine that it is at interrupt level. This situation
can result in failures as follows:
$task IRQ SoftIRQ
rcu_read_lock()
/* do stuff */
<preempt> |= UNLOCK_BLOCKED
rcu_read_unlock()
--t->rcu_read_lock_nesting
irq_enter();
/* do stuff, don't use RCU */
irq_exit();
sub_preempt_count(IRQ_EXIT_OFFSET);
invoke_softirq()
ttwu();
spin_lock_irq(&pi->lock)
rcu_read_lock();
/* do stuff */
rcu_read_unlock();
rcu_read_unlock_special()
rcu_report_exp_rnp()
ttwu()
spin_lock_irq(&pi->lock) /* deadlock */
rcu_read_unlock_special(t);
Ed can simply trigger this 'easy' because invoke_softirq() immediately
does a ttwu() of ksoftirqd/# instead of doing the in-place softirq stuff
first, but even without that the above happens.
Cure this by also excluding softirqs from the
rcu_read_unlock_special() handler and ensuring the force_irqthreads
ksoftirqd/# wakeup is done from full softirq context.
[ Alternatively, delaying the ->rcu_read_lock_nesting decrement
until after the special handling would make the thing more robust
in the face of interrupts as well. And there is a separate patch
for that. ]
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-and-tested-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Commit a26ac2455ffcf3(rcu: move TREE_RCU from softirq to kthread)
introduced performance regression. In an AIM7 test, this commit degraded
performance by about 40%.
The commit runs rcu callbacks in a kthread instead of softirq. We observed
high rate of context switch which is caused by this. Out test system has
64 CPUs and HZ is 1000, so we saw more than 64k context switch per second
which is caused by RCU's per-CPU kthread. A trace showed that most of
the time the RCU per-CPU kthread doesn't actually handle any callbacks,
but instead just does a very small amount of work handling grace periods.
This means that RCU's per-CPU kthreads are making the scheduler do quite
a bit of work in order to allow a very small amount of RCU-related
processing to be done.
Alex Shi's analysis determined that this slowdown is due to lock
contention within the scheduler. Unfortunately, as Peter Zijlstra points
out, the scheduler's real-time semantics require global action, which
means that this contention is inherent in real-time scheduling. (Yes,
perhaps someone will come up with a workaround -- otherwise, -rt is not
going to do well on large SMP systems -- but this patch will work around
this issue in the meantime. And "the meantime" might well be forever.)
This patch therefore re-introduces softirq processing to RCU, but only
for core RCU work. RCU callbacks are still executed in kthread context,
so that only a small amount of RCU work runs in softirq context in the
common case. This should minimize ksoftirqd execution, allowing us to
skip boosting of ksoftirqd for CONFIG_RCU_BOOST=y kernels.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: "Alex,Shi" <alex.shi@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
If RCU priority boosting is to be meaningful, callback invocation must
be boosted in addition to preempted RCU readers. Otherwise, in presence
of CPU real-time threads, the grace period ends, but the callbacks don't
get invoked. If the callbacks don't get invoked, the associated memory
doesn't get freed, so the system is still subject to OOM.
But it is not reasonable to priority-boost RCU_SOFTIRQ, so this commit
moves the callback invocations to a kthread, which can be boosted easily.
Also add comments and properly synchronized all accesses to
rcu_cpu_kthread_task, as suggested by Lai Jiangshan.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
ksoftirqd, kworker, migration, and pktgend kthreads can be created with
kthread_create_on_node(), to get proper NUMA affinities for their stack and
task_struct.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (116 commits)
x86: Enable forced interrupt threading support
x86: Mark low level interrupts IRQF_NO_THREAD
x86: Use generic show_interrupts
x86: ioapic: Avoid redundant lookup of irq_cfg
x86: ioapic: Use new move_irq functions
x86: Use the proper accessors in fixup_irqs()
x86: ioapic: Use irq_data->state
x86: ioapic: Simplify irq chip and handler setup
x86: Cleanup the genirq name space
genirq: Add chip flag to force mask on suspend
genirq: Add desc->irq_data accessor
genirq: Add comments to Kconfig switches
genirq: Fixup fasteoi handler for oneshot mode
genirq: Provide forced interrupt threading
sched: Switch wait_task_inactive to schedule_hrtimeout()
genirq: Add IRQF_NO_THREAD
genirq: Allow shared oneshot interrupts
genirq: Prepare the handling of shared oneshot interrupts
genirq: Make warning in handle_percpu_event useful
x86: ioapic: Move trigger defines to io_apic.h
...
Fix up trivial(?) conflicts in arch/x86/pci/xen.c due to genirq name
space changes clashing with the Xen cleanups. The set_irq_msi() had
moved to xen_bind_pirq_msi_to_irq().
Add a commandline parameter "threadirqs" which forces all interrupts except
those marked IRQF_NO_THREAD to run threaded. That's mostly a debug option to
allow retrieving better debug data from crashing interrupt handlers. If
"threadirqs" is not enabled on the kernel command line, then there is no
impact in the interrupt hotpath.
Architecture code needs to select CONFIG_IRQ_FORCED_THREADING after
marking the interrupts which cant be threaded IRQF_NO_THREAD. All
interrupts which have IRQF_TIMER set are implict marked
IRQF_NO_THREAD. Also all PER_CPU interrupts are excluded.
Forced threading hard interrupts also forces all soft interrupt
handling into thread context.
When enabled it might slow down things a bit, but for debugging problems in
interrupt code it's a reasonable penalty as it does not immediately
crash and burn the machine when an interrupt handler is buggy.
Some test results on a Core2Duo machine:
Cache cold run of:
# time git grep irq_desc
non-threaded threaded
real 1m18.741s 1m19.061s
user 0m1.874s 0m1.757s
sys 0m5.843s 0m5.427s
# iperf -c server
non-threaded
[ 3] 0.0-10.0 sec 1.09 GBytes 933 Mbits/sec
[ 3] 0.0-10.0 sec 1.09 GBytes 934 Mbits/sec
[ 3] 0.0-10.0 sec 1.09 GBytes 933 Mbits/sec
threaded
[ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec
[ 3] 0.0-10.0 sec 1.09 GBytes 934 Mbits/sec
[ 3] 0.0-10.0 sec 1.09 GBytes 937 Mbits/sec
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20110223234956.772668648@linutronix.de>
ksoftirqd() calls do_softirq() which switches stacks on several
architectures. That makes no sense at all. ksoftirqd's stack is
sufficient.
Call __do_softirq() directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: David Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
LKML-Reference: <alpine.LFD.2.00.1102021704530.31804@localhost6.localdomain6>
Cleanup patch, freeing up PF_KSOFTIRQD and use per_cpu ksoftirqd pointer
instead, as suggested by Eric Dumazet.
Tested-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1292980144-28796-2-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For arch which needs USE_GENERIC_SMP_HELPERS, it has to select
USE_GENERIC_SMP_HELPERS, rather than leaving a choice to user, since they
don't provide their own implementions.
Also, move on_each_cpu() to kernel/smp.c, it is strange to put it in
kernel/softirq.c.
For arch which doesn't use USE_GENERIC_SMP_HELPERS, e.g. blackfin, only
on_each_cpu() is compiled.
Signed-off-by: Amerigo Wang <amwang@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (30 commits)
gameport: use this_cpu_read instead of lookup
x86: udelay: Use this_cpu_read to avoid address calculation
x86: Use this_cpu_inc_return for nmi counter
x86: Replace uses of current_cpu_data with this_cpu ops
x86: Use this_cpu_ops to optimize code
vmstat: User per cpu atomics to avoid interrupt disable / enable
irq_work: Use per cpu atomics instead of regular atomics
cpuops: Use cmpxchg for xchg to avoid lock semantics
x86: this_cpu_cmpxchg and this_cpu_xchg operations
percpu: Generic this_cpu_cmpxchg() and this_cpu_xchg support
percpu,x86: relocate this_cpu_add_return() and friends
connector: Use this_cpu operations
xen: Use this_cpu_inc_return
taskstats: Use this_cpu_ops
random: Use this_cpu_inc_return
fs: Use this_cpu_inc_return in buffer.c
highmem: Use this_cpu_xx_return() operations
vmstat: Use this_cpu_inc_return for vm statistics
x86: Support for this_cpu_add, sub, dec, inc_return
percpu: Generic support for this_cpu_add, sub, dec, inc_return
...
Fixed up conflicts: in arch/x86/kernel/{apic/nmi.c, apic/x2apic_uv_x.c, process.c}
as per Tejun.
Function-scope statics are discouraged because they are
easily overlooked and can cause subtle bugs/races due to
their global (non-SMP safe) nature.
Linus noticed that we did this for sched_param - at minimum
make the const.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: Message-ID: <AANLkTinotRxScOHEb0HgFgSpGPkq_6jKTv5CfvnQM=ee@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
__get_cpu_var() can be replaced with this_cpu_read and will then use a
single read instruction with implied address calculation to access the
correct per cpu instance.
However, the address of a per cpu variable passed to __this_cpu_read()
cannot be determined (since it's an implied address conversion through
segment prefixes). Therefore apply this only to uses of __get_cpu_var
where the address of the variable is not used.
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Hugh Dickins <hughd@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Andrew Morton pointed out almost all sched_setscheduler() callers are
using fixed parameters and can be converted to static. It reduces runtime
memory use a little.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: James Morris <jmorris@namei.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'softirq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softirqs: Make wakeup_softirqd static
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, asm: Restore parentheses around one pushl_cfi argument
x86, asm: Fix ancient-GAS workaround
x86, asm: Fix CFI macro invocations to deal with shortcomings in gas
* 'x86-numa-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, numa: Assign CPUs to nodes in round-robin manner on fake NUMA
* 'x86-quirks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: HPET force enable for CX700 / VIA Epia LT
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: Use string copy operation to optimze copy in kernel compression
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Use allocated buffer in tlb_uv.c:tunables_read()
* 'x86-vm86-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vm86: Fix preemption bug for int1 debug and int3 breakpoint handlers.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (96 commits)
apic, x86: Use BIOS settings for IBS and MCE threshold interrupt LVT offsets
apic, x86: Check if EILVT APIC registers are available (AMD only)
x86: ioapic: Call free_irte only if interrupt remapping enabled
arm: Use ARCH_IRQ_INIT_FLAGS
genirq, ARM: Fix boot on ARM platforms
genirq: Fix CONFIG_GENIRQ_NO_DEPRECATED=y build
x86: Switch sparse_irq allocations to GFP_KERNEL
genirq: Switch sparse_irq allocator to GFP_KERNEL
genirq: Make sparse_lock a mutex
x86: lguest: Use new irq allocator
genirq: Remove the now unused sparse irq leftovers
genirq: Sanitize dynamic irq handling
genirq: Remove arch_init_chip_data()
x86: xen: Sanitise sparse_irq handling
x86: Use sane enumeration
x86: uv: Clean up the direct access to irq_desc
x86: Make io_apic.c local functions static
genirq: Remove irq_2_iommu
x86: Speed up the irq_remapped check in hot pathes
intr_remap: Simplify the code further
...
Fix up trivial conflicts in arch/x86/Kconfig
With the addition of trace_softirq_raise() the softirq tracepoint got
even more convoluted. Why the tracepoints take two pointers to assign
an integer is beyond my comprehension.
But adding an extra case which treats the first pointer as an unsigned
long when the second pointer is NULL including the back and forth
type casting is just horrible.
Convert the softirq tracepoints to take a single unsigned int argument
for the softirq vector number and fix the call sites.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1010191428560.6815@localhost6.localdomain6>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: mathieu.desnoyers@efficios.com
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
When CPU is idle and on first interrupt, irq_enter calls tick_check_idle()
to notify interruption from idle. But, there is a problem if this call
is done after __irq_enter, as all routines in __irq_enter may find
stale time due to yet to be done tick_check_idle.
Specifically, trace calls in __irq_enter when they use global clock and also
account_system_vtime change in this patch as it wants to use sched_clock_cpu()
to do proper irq timing.
But, tick_check_idle was moved after __irq_enter intentionally to
prevent problem of unneeded ksoftirqd wakeups by the commit ee5f80a:
irq: call __irq_enter() before calling the tick_idle_check
Impact: avoid spurious ksoftirqd wakeups
Moving tick_check_idle() before __irq_enter and wrapping it with
local_bh_enable/disable would solve both the problems.
Fixed-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1286237003-12406-9-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To account softirq time cleanly in scheduler, we need to identify whether
softirq is invoked in ksoftirqd context or softirq at hardirq tail context.
Add PF_KSOFTIRQD for that purpose.
As all PF flag bits are currently taken, create space by moving one of the
infrequently used bits (PF_THREAD_BOUND) down in task_struct to be along
with some other state fields.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1286237003-12406-4-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra found a bug in the way softirq time is accounted in
VIRT_CPU_ACCOUNTING on this thread:
http://lkml.indiana.edu/hypermail//linux/kernel/1009.2/01366.html
The problem is, softirq processing uses local_bh_disable internally. There
is no way, later in the flow, to differentiate between whether softirq is
being processed or is it just that bh has been disabled. So, a hardirq when bh
is disabled results in time being wrongly accounted as softirq.
Looking at the code a bit more, the problem exists in !VIRT_CPU_ACCOUNTING
as well. As account_system_time() in normal tick based accouting also uses
softirq_count, which will be set even when not in softirq with bh disabled.
Peter also suggested solution of using 2*SOFTIRQ_OFFSET as irq count
for local_bh_{disable,enable} and using just SOFTIRQ_OFFSET while softirq
processing. The patch below does that and adds API in_serving_softirq() which
returns whether we are currently processing softirq or not.
Also changes one of the usages of softirq_count in net/sched/cls_cgroup.c
to in_serving_softirq.
Looks like many usages of in_softirq really want in_serving_softirq. Those
changes can be made individually on a case by case basis.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1286237003-12406-2-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This function should have not been there in the first place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
sparse irq sets up NR_IRQS_LEGACY irq descriptors and archs then go
ahead and allocate more.
Use the unused return value of arch_probe_nr_irqs() to let the
architecture return the number of early allocations. Fix up all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
The commit 80b5184cc5 ("kernel/: convert cpu
notifier to return encapsulate errno value") changed the return value of
cpu notifier callbacks.
Those callbacks don't return NOTIFY_BAD on failures anymore. But there
are a few callbacks which are called directly at init time and checking
the return value.
I forgot to change BUG_ON checking by the direct callers in the commit.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By the previous modification, the cpu notifier can return encapsulate
errno value. This converts the cpu notifiers for kernel/*.c
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The addition of preemptible RCU to treercu resulted in a bit of
confusion and inefficiency surrounding the handling of context switches
for RCU-sched and for RCU-preempt. For RCU-sched, a context switch
is a quiescent state, pure and simple, just like it always has been.
For RCU-preempt, a context switch is in no way a quiescent state, but
special handling is required when a task blocks in an RCU read-side
critical section.
However, the callout from the scheduler and the outer loop in ksoftirqd
still calls something named rcu_sched_qs(), whose name is no longer
accurate. Furthermore, when rcu_check_callbacks() notes an RCU-sched
quiescent state, it ends up unnecessarily (though harmlessly, aside
from the performance hit) enqueuing the current task if it happens to
be running in an RCU-preempt read-side critical section. This not only
increases the maximum latency of scheduler_tick(), it also needlessly
increases the overhead of the next outermost rcu_read_unlock() invocation.
This patch addresses this situation by separating the notion of RCU's
context-switch handling from that of RCU-sched's quiescent states.
The context-switch handling is covered by rcu_note_context_switch() in
general and by rcu_preempt_note_context_switch() for preemptible RCU.
This permits rcu_sched_qs() to handle quiescent states and only quiescent
states. It also reduces the maximum latency of scheduler_tick(), though
probably by much less than a microsecond. Finally, it means that tasks
within preemptible-RCU read-side critical sections avoid incurring the
overhead of queuing unless there really is a context switch.
Suggested-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
hrtimers callbacks are always done from hardirq context, either the
jiffy tick interrupt or the hrtimer device interrupt.
[ there is currently one exception that can still call a hrtimer
callback from softirq, but even in that case this will still
work correctly. ]
Reported-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Yury Polyanskiy <ypolyans@princeton.edu>
Tested-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
LKML-Reference: <1265120401.24455.306.camel@laptop>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
Currently, rcu_irq_exit() is invoked only for CONFIG_NO_HZ,
while rcu_irq_enter() is invoked unconditionally. This patch
moves rcu_irq_exit() out from under CONFIG_NO_HZ so that the
calls are balanced.
This patch has no effect on the behavior of the kernel because
both rcu_irq_enter() and rcu_irq_exit() are empty for
!CONFIG_NO_HZ, but the code is easier to understand if the calls
are obviously balanced in all cases.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: dipankar@in.ibm.com
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <12567428891605-git-send-email->
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch updates percpu related symbols under kernel/ and mm/ such
that percpu symbols are unique and don't clash with local symbols.
This serves two purposes of decreasing the possibility of global
percpu symbol collision and allowing dropping per_cpu__ prefix from
percpu symbols.
* kernel/lockdep.c: s/lock_stats/cpu_lock_stats/
* kernel/sched.c: s/init_rq_rt/init_rt_rq_var/ (any better idea?)
s/sched_group_cpus/sched_groups/
* kernel/softirq.c: s/ksoftirqd/run_ksoftirqd/a
* kernel/softlockup.c: s/(*)_timestamp/softlockup_\1_ts/
s/watchdog_task/softlockup_watchdog/
s/timestamp/ts/ for local variables
* kernel/time/timer_stats: s/lookup_lock/tstats_lookup_lock/
* mm/slab.c: s/reap_work/slab_reap_work/
s/reap_node/slab_reap_node/
* mm/vmstat.c: local variable changed to avoid collision with vmstat_work
Partly based on Rusty Russell's "alloc_percpu: rename percpu vars
which cause name clashes" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: (slab/vmstat) Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
With BLOCK_IOPOLL_SOFTIRQ added, softirq_to_name[] and
show_softirq_name() needs to be updated.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4AB20398.8070209@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
commit ca109491f (hrtimer: removing all ur callback modes) moved all
hrtimer callbacks into hard interrupt context when high resolution
timers are active. That breaks code which relied on the assumption
that the callback happens in softirq context.
Provide a generic infrastructure which combines tasklets and hrtimers
together to provide an in-softirq hrtimer experience.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: torvalds@linux-foundation.org
Cc: kaber@trash.net
Cc: David Miller <davem@davemloft.net>
LKML-Reference: <1248265724.27058.1366.camel@twins>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Statistics for softirq doesn't exist.
It will be helpful like statistics for interrupts.
This patch introduces counting the number of softirq,
which will be exported in /proc/softirqs.
When softirq handler consumes much CPU time,
/proc/stat is like the following.
$ while :; do cat /proc/stat | head -n1 ; sleep 10 ; done
cpu 88 0 408 739665 583 28 2 0 0
cpu 450 0 1090 740970 594 28 1294 0 0
^^^^
softirq
In such a situation,
/proc/softirqs shows us which softirq handler is invoked.
We can see the increase rate of softirqs.
<before>
$ cat /proc/softirqs
CPU0 CPU1 CPU2 CPU3
HI 0 0 0 0
TIMER 462850 462805 462782 462718
NET_TX 0 0 0 365
NET_RX 2472 2 2 40
BLOCK 0 0 381 1164
TASKLET 0 0 0 224
SCHED 462654 462689 462698 462427
RCU 3046 2423 3367 3173
<after>
$ cat /proc/softirqs
CPU0 CPU1 CPU2 CPU3
HI 0 0 0 0
TIMER 463361 465077 465056 464991
NET_TX 53 0 1 365
NET_RX 3757 2 2 40
BLOCK 0 0 398 1170
TASKLET 0 0 0 224
SCHED 463074 464318 464612 463330
RCU 3505 2948 3947 3673
When CPU TIME of softirq is high,
the rates of increase is the following.
TIMER : 220/sec : CPU1-3
NET_TX : 5/sec : CPU0
NET_RX : 120/sec : CPU0
SCHED : 40-200/sec : all CPU
RCU : 45-58/sec : all CPU
The rates of increase in an idle mode is the following.
TIMER : 250/sec
SCHED : 250/sec
RCU : 2/sec
It seems many softirqs for receiving packets and rcu are invoked. This
gives us help for checking system.
Signed-off-by: Keika Kobayashi <kobayashi.kk@ncos.nec.co.jp>
Reviewed-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rationale: kmemcheck needs to be able to schedule a tasklet without
touching any dynamically allocated memory _at_ _all_ (since that would
lead to a recursive page fault). This tasklet is used for writing the
error reports to the kernel log.
The new scheduling function avoids touching any other tasklets by
inserting the new tasklist as the head of the "tasklet_hi" list instead
of on the tail.
Also don't wake up the softirq thread lest the scheduler access some
tracked memory and we go down with a recursive page fault.
In this case, we'd better just wait for the maximum time of 1/HZ for the
message to appear.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
Merge reason: tracing/core was on a .30-rc1 base and was missing out on
on a handful of tracing fixes present in .30-rc5-almost.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"tracing: create automated trace defines" causes this compile error on s390,
as reported by Sachin Sant against linux-next:
kernel/built-in.o: In function `__do_softirq':
(.text+0x1c680): undefined reference to `__tracepoint_softirq_entry'
This happens because the definitions of the softirq tracepoints were moved
from kernel/softirq.c to kernel/irq/handle.c. Since s390 doesn't support
generic hardirqs handle.c doesn't get compiled and the definitions are
missing.
So move the tracepoints to softirq.c again.
[ Impact: fix build failure on s390 ]
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: fweisbec@gmail.com
LKML-Reference: <20090429135139.5fac79b8@osiris.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This simplifies the node awareness of the code. All our allocators
only deal with a NUMA node ID locality not with CPU ids anyway - so
there's no need to maintain (and transform) a CPU id all across the
IRq layer.
v2: keep move_irq_desc related
[ Impact: cleanup, prepare IRQ code to be NUMA-aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
LKML-Reference: <49F65536.2020300@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix sparse warning in kernel/softirq.c.
warning: do-while statement is not a compound statement
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
LKML-Reference: <BD79186B4FD85F4B8E60E381CAEE1909015F9033@mi8nycmail19.Mi8.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clean up
Create a sub directory in include/trace called events to keep the
trace point headers in their own separate directory. Only headers that
declare trace points should be defined in this directory.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch lowers the number of places a developer must modify to add
new tracepoints. The current method to add a new tracepoint
into an existing system is to write the trace point macro in the
trace header with one of the macros TRACE_EVENT, TRACE_FORMAT or
DECLARE_TRACE, then they must add the same named item into the C file
with the macro DEFINE_TRACE(name) and then add the trace point.
This change cuts out the needing to add the DEFINE_TRACE(name).
Every file that uses the tracepoint must still include the trace/<type>.h
file, but the one C file must also add a define before the including
of that file.
#define CREATE_TRACE_POINTS
#include <trace/mytrace.h>
This will cause the trace/mytrace.h file to also produce the C code
necessary to implement the trace point.
Note, if more than one trace/<type>.h is used to create the C code
it is best to list them all together.
#define CREATE_TRACE_POINTS
#include <trace/foo.h>
#include <trace/bar.h>
#include <trace/fido.h>
Thanks to Mathieu Desnoyers and Christoph Hellwig for coming up with
the cleaner solution of the define above the includes over my first
design to have the C code include a "special" header.
This patch converts sched, irq and lockdep and skb to use this new
method.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* 'ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
s390: remove arch specific smp_send_stop()
panic: clean up kernel/panic.c
panic, smp: provide smp_send_stop() wrapper on UP too
panic: decrease oops_in_progress only after having done the panic
generic-ipi: eliminate WARN_ON()s during oops/panic
generic-ipi: cleanups
generic-ipi: remove CSD_FLAG_WAIT
generic-ipi: remove kmalloc()
generic IPI: simplify barriers and locking
It appears I inadvertly introduced rq->lock recursion to the
hrtimer_start() path when I delegated running already expired
timers to softirq context.
This patch fixes it by introducing a __hrtimer_start_range_ns()
method that will not use raise_softirq_irqoff() but
__raise_softirq_irqoff() which avoids the wakeup.
It then also changes schedule() to check for pending softirqs and
do the wakeup then, I'm not quite sure I like this last bit, nor
am I convinced its really needed.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus@samba.org
LKML-Reference: <20090313112301.096138802@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clean up
It is redundant to have 'SOFTIRQ' in the softirq names.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Introduce softirq entry/exit tracepoints. These are useful for
augmenting existing tracers, and to figure out softirq frequencies and
timings.
[
s/irq_softirq_/softirq_/ for trace point names and
Fixed printf format in TRACE_FORMAT macro
- Steven Rostedt
]
LKML-Reference: <20090312183603.GC3352@redhat.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Create a 'softirq_to_name' array, which is indexed by softirq #, so
that we can easily convert between the softirq index # and its name, in
order to get more meaningful output messages.
LKML-Reference: <20090312183336.GB3352@redhat.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Impact: cleanup
The naming clashes with upcoming softirq tracepoints, so rename the
APIs to lockdep_*().
Requested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If a machine is flooded by network frames, a cpu can loop
100% of its time inside ksoftirqd() without calling schedule().
This can delay RCU grace period to insane values.
Adding rcu_qsctr_inc() call in ksoftirqd() solves this problem.
Paul: "This regression was a result of the recent change from
"schedule()" to "cond_resched()", which got rid of that quiescent
state in the common case where a reschedule is not needed".
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Oleg noticed that we don't strictly need CSD_FLAG_WAIT, rework
the code so that we can use CSD_FLAG_LOCK for both purposes.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix to preempt trace triggering lockdep check_flag failure
In local_bh_disable, the use of add_preempt_count causes the
preempt tracer to start recording the time preemption is off.
But because it already modified the preempt_count to show
softirqs disabled, and before it called the lockdep code to
handle this, it causes a state that lockdep can not handle.
The preempt tracer will reset the ring buffer on start of a trace,
and the ring buffer reset code does a spin_lock_irqsave. This
calls into lockdep and lockdep will fail when it detects the
invalid state of having softirqs disabled but the internal
current->softirqs_enabled is still set.
The fix is to manually add the SOFTIRQ_OFFSET to preempt count
and call the preempt tracer code outside the lockdep critical
area.
Thanks to Peter Zijlstra for suggesting this solution.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
Impact: Remove obsolete API usage
any_online_cpu() is a good name, but it takes a cpumask_t, not a
pointer.
There are several places where any_online_cpu() doesn't really want a
mask arg at all. Replace all callers with cpumask_any() and
cpumask_any_and().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
* 'irq-fixes-for-linus-4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sparseirq: move __weak symbols into separate compilation unit
sparseirq: work around __weak alias bug
sparseirq: fix hang with !SPARSE_IRQ
sparseirq: set lock_class for legacy irq when sparse_irq is selected
sparseirq: work around compiler optimizing away __weak functions
sparseirq: fix desc->lock init
sparseirq: do not printk when migrating IRQ descriptors
sparseirq: remove duplicated arch_early_irq_init()
irq: simplify for_each_irq_desc() usage
proc: remove ifdef CONFIG_SPARSE_IRQ from stat.c
irq: for_each_irq_desc() move to irqnr.h
hrtimer: remove #include <linux/irq.h>
GCC has a bug with __weak alias functions: if the functions are in
the same compilation unit as their call site, GCC can decide to
inline them - and thus rob the linker of the opportunity to override
the weak alias with the real thing.
So move all the IRQ handling related __weak symbols to kernel/irq/chip.c.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes a long-standing performance bug in classic RCU that
results in massive internal-to-RCU lock contention on systems with
more than a few hundred CPUs. Although this patch creates a separate
flavor of RCU for ease of review and patch maintenance, it is intended
to replace classic RCU.
This patch still handles stress better than does mainline, so I am still
calling it ready for inclusion. This patch is against the -tip tree.
Nevertheless, experience on an actual 1000+ CPU machine would still be
most welcome.
Most of the changes noted below were found while creating an rcutiny
(which should permit ejecting the current rcuclassic) and while doing
detailed line-by-line documentation.
Updates from v9 (http://lkml.org/lkml/2008/12/2/334):
o Fixes from remainder of line-by-line code walkthrough,
including comment spelling, initialization, undesirable
narrowing due to type conversion, removing redundant memory
barriers, removing redundant local-variable initialization,
and removing redundant local variables.
I do not believe that any of these fixes address the CPU-hotplug
issues that Andi Kleen was seeing, but please do give it a whirl
in case the machine is smarter than I am.
A writeup from the walkthrough may be found at the following
URL, in case you are suffering from terminal insomnia or
masochism:
http://www.kernel.org/pub/linux/kernel/people/paulmck/tmp/rcutree-walkthrough.2008.12.16a.pdf
o Made rcutree tracing use seq_file, as suggested some time
ago by Lai Jiangshan.
o Added a .csv variant of the rcudata debugfs trace file, to allow
people having thousands of CPUs to drop the data into
a spreadsheet. Tested with oocalc and gnumeric. Updated
documentation to suit.
Updates from v8 (http://lkml.org/lkml/2008/11/15/139):
o Fix a theoretical race between grace-period initialization and
force_quiescent_state() that could occur if more than three
jiffies were required to carry out the grace-period
initialization. Which it might, if you had enough CPUs.
o Apply Ingo's printk-standardization patch.
o Substitute local variables for repeated accesses to global
variables.
o Fix comment misspellings and redundant (but harmless) increments
of ->n_rcu_pending (this latter after having explicitly added it).
o Apply checkpatch fixes.
Updates from v7 (http://lkml.org/lkml/2008/10/10/291):
o Fixed a number of problems noted by Gautham Shenoy, including
the cpu-stall-detection bug that he was having difficulty
convincing me was real. ;-)
o Changed cpu-stall detection to wait for ten seconds rather than
three in order to reduce false positive, as suggested by Ingo
Molnar.
o Produced a design document (http://lwn.net/Articles/305782/).
The act of writing this document uncovered a number of both
theoretical and "here and now" bugs as noted below.
o Fix dynticks_nesting accounting confusion, simplify WARN_ON()
condition, fix kerneldoc comments, and add memory barriers
in dynticks interface functions.
o Add more data to tracing.
o Remove unused "rcu_barrier" field from rcu_data structure.
o Count calls to rcu_pending() from scheduling-clock interrupt
to use as a surrogate timebase should jiffies stop counting.
o Fix a theoretical race between force_quiescent_state() and
grace-period initialization. Yes, initialization does have to
go on for some jiffies for this race to occur, but given enough
CPUs...
Updates from v6 (http://lkml.org/lkml/2008/9/23/448):
o Fix a number of checkpatch.pl complaints.
o Apply review comments from Ingo Molnar and Lai Jiangshan
on the stall-detection code.
o Fix several bugs in !CONFIG_SMP builds.
o Fix a misspelled config-parameter name so that RCU now announces
at boot time if stall detection is configured.
o Run tests on numerous combinations of configurations parameters,
which after the fixes above, now build and run correctly.
Updates from v5 (http://lkml.org/lkml/2008/9/15/92, bad subject line):
o Fix a compiler error in the !CONFIG_FANOUT_EXACT case (blew a
changeset some time ago, and finally got around to retesting
this option).
o Fix some tracing bugs in rcupreempt that caused incorrect
totals to be printed.
o I now test with a more brutal random-selection online/offline
script (attached). Probably more brutal than it needs to be
on the people reading it as well, but so it goes.
o A number of optimizations and usability improvements:
o Make rcu_pending() ignore the grace-period timeout when
there is no grace period in progress.
o Make force_quiescent_state() avoid going for a global
lock in the case where there is no grace period in
progress.
o Rearrange struct fields to improve struct layout.
o Make call_rcu() initiate a grace period if RCU was
idle, rather than waiting for the next scheduling
clock interrupt.
o Invoke rcu_irq_enter() and rcu_irq_exit() only when
idle, as suggested by Andi Kleen. I still don't
completely trust this change, and might back it out.
o Make CONFIG_RCU_TRACE be the single config variable
manipulated for all forms of RCU, instead of the prior
confusion.
o Document tracing files and formats for both rcupreempt
and rcutree.
Updates from v4 for those missing v5 given its bad subject line:
o Separated dynticks interface so that NMIs and irqs call separate
functions, greatly simplifying it. In particular, this code
no longer requires a proof of correctness. ;-)
o Separated dynticks state out into its own per-CPU structure,
avoiding the duplicated accounting.
o The case where a dynticks-idle CPU runs an irq handler that
invokes call_rcu() is now correctly handled, forcing that CPU
out of dynticks-idle mode.
o Review comments have been applied (thank you all!!!).
For but one example, fixed the dynticks-ordering issue that
Manfred pointed out, saving me much debugging. ;-)
o Adjusted rcuclassic and rcupreempt to handle dynticks changes.
Attached is an updated patch to Classic RCU that applies a hierarchy,
greatly reducing the contention on the top-level lock for large machines.
This passes 10-hour concurrent rcutorture and online-offline testing on
128-CPU ppc64 without dynticks enabled, and exposes some timekeeping
bugs in presence of dynticks (exciting working on a system where
"sleep 1" hangs until interrupted...), which were fixed in the
2.6.27 kernel. It is getting more reliable than mainline by some
measures, so the next version will be against -tip for inclusion.
See also Manfred Spraul's recent patches (or his earlier work from
2004 at http://marc.info/?l=linux-kernel&m=108546384711797&w=2).
We will converge onto a common patch in the fullness of time, but are
currently exploring different regions of the design space. That said,
I have already gratefully stolen quite a few of Manfred's ideas.
This patch provides CONFIG_RCU_FANOUT, which controls the bushiness
of the RCU hierarchy. Defaults to 32 on 32-bit machines and 64 on
64-bit machines. If CONFIG_NR_CPUS is less than CONFIG_RCU_FANOUT,
there is no hierarchy. By default, the RCU initialization code will
adjust CONFIG_RCU_FANOUT to balance the hierarchy, so strongly NUMA
architectures may choose to set CONFIG_RCU_FANOUT_EXACT to disable
this balancing, allowing the hierarchy to be exactly aligned to the
underlying hardware. Up to two levels of hierarchy are permitted
(in addition to the root node), allowing up to 16,384 CPUs on 32-bit
systems and up to 262,144 CPUs on 64-bit systems. I just know that I
am going to regret saying this, but this seems more than sufficient
for the foreseeable future. (Some architectures might wish to set
CONFIG_RCU_FANOUT=4, which would limit such architectures to 64 CPUs.
If this becomes a real problem, additional levels can be added, but I
doubt that it will make a significant difference on real hardware.)
In the common case, a given CPU will manipulate its private rcu_data
structure and the rcu_node structure that it shares with its immediate
neighbors. This can reduce both lock and memory contention by multiple
orders of magnitude, which should eliminate the need for the strange
manipulations that are reported to be required when running Linux on
very large systems.
Some shortcomings:
o More bugs will probably surface as a result of an ongoing
line-by-line code inspection.
Patches will be provided as required.
o There are probably hangs, rcutorture failures, &c. Seems
quite stable on a 128-CPU machine, but that is kind of small
compared to 4096 CPUs. However, seems to do better than
mainline.
Patches will be provided as required.
o The memory footprint of this version is several KB larger
than rcuclassic.
A separate UP-only rcutiny patch will be provided, which will
reduce the memory footprint significantly, even compared
to the old rcuclassic. One such patch passes light testing,
and has a memory footprint smaller even than rcuclassic.
Initial reaction from various embedded guys was "it is not
worth it", so am putting it aside.
Credits:
o Manfred Spraul for ideas, review comments, and bugs spotted,
as well as some good friendly competition. ;-)
o Josh Triplett, Ingo Molnar, Peter Zijlstra, Mathieu Desnoyers,
Lai Jiangshan, Andi Kleen, Andy Whitcroft, and Andrew Morton
for reviews and comments.
o Thomas Gleixner for much-needed help with some timer issues
(see patches below).
o Jon M. Tollefson, Tim Pepper, Andrew Theurer, Jose R. Santos,
Andy Whitcroft, Darrick Wong, Nishanth Aravamudan, Anton
Blanchard, Dave Kleikamp, and Nathan Lynch for keeping machines
alive despite my heavy abuse^Wtesting.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: remove unused code
__local_bh_enable has been replaced with _local_bh_enable.
As comments says "it always nests inside local_bh_enable() sections"
has not been valid now. Also there is no reason to use __local_bh_enable
anywhere, so we can remove this useless function.
Signed-off-by: Liming Wang <liming.wang@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: avoid spurious ksoftirqd wakeups
The tick idle check which is called from irq_enter() was run before
the call to __irq_enter() which did not set the in_interrupt() bits in
preempt_count. That way the raise of a softirq woke up softirqd for
nothing as the softirq was handled on return from interrupt.
Call __irq_enter() before calling into the tick idle check code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have two separate nohz function calls in irq_enter() for no good
reason. Just call a single NOHZ function from irq_enter() and call
the bits in the tick code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is basically a genericization of Jens Axboe's block layer
remote softirq changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This fixes the broken 77af7e3403
("softirq, warning fix: correct a format to avoid a warning") fix
correctly.
The type of a pointer subtraction is not "int", nor is it "long". It
can be either (or something else). It's "ptrdiff_t", and the printk
format for it is "%td".
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Last -tip gives this warning:
kernel/softirq.c: Dans la fonction «__do_softirq» :
kernel/softirq.c:216: attention : format «%ld» expects type «long int», but argument 2 has type «int»
This patch corrects the format type, and a small mistake in the "softirq" word.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
