Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds voltage regulator driver for Maxim 8998 chip. This chip
is used on Samsung Aquila and GONI boards and provides following
functionalities:
- 4 BUCK voltage converters, 17 LDO power regulators and 5 other power
controllers
- battery charger
This patch adds basic driver for voltage regulators and MAX 8998 MFD core.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This device is very simple, it supports one buck and two LDOs. The LDOs are
fixed-voltage. Only the buck is programable over the I2C bus to 16 possible
voltages.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some systems are likely to want this to be subsys_initcall() to
make sure the regulator is available prior to the consumers.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The AD5398 and AD5821 are single 10-bit DAC with 120 mA output current
sink capability. They feature an internal reference and operates from
a single 2.7 V to 5.5 V supply.
This driver supports both the AD5398 and the AD5821. It adapts into the
voltage and current framework.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In TPS6507x, depending on the status of DEFDCDC{2,3} pin either
DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or
programmed to change the output voltage.
The current driver assumes DEFDCDC{2,3} pins are always tied low
and thus operates only on DEFDCDC{2,3}_LOW register. This need
not always be the case (as is found on OMAP-L138 EVM).
Unfortunately, software cannot read the status of DEFDCDC{2,3} pins.
So, this information is passed through platform data depending on
how the board is wired.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In the case of platform_device_add() fail, we should call
platform_device_put() instead of platform_device_del()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We use voltage selector as an array index for typ_voltages.
Thus the valid range for voltage selector should be 0..voltages_len-1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04d to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The interface for the AB3100 is changed to make way for the
ABX500 family of chips: AB3550, AB5500 and future ST-Ericsson
Analog Baseband chips. The register access functions are moved
out to a separate struct abx500_ops. In this way the interface
is moved from the implementation and the sub functionality drivers
can keep their interface intact when chip infrastructure and
communication mechanisms changes. We also define the AB3550
device IDs and the AB3550 platform data struct and convert
the catenated 32bit event to an array of 3 x 8bits.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The goal here is to make way for a more general interface for the
analog baseband chips ab3100 ab3550 ab550 and future chips.
This patch have been divided into two parts since both changing name
and content of a file is not recommended in git.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPS6507x are multi function (PM, touchscreen) chipsets from TI.
This commit also changes the corresponding regulator driver from being
standalone to an MFD subdevice.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Move from using tps or tsp6507x to tps6057x_pmic in a consistent manner.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add mfd structure which refrences sub-driver initialization data. For example,
for a giving hardware implementation, the voltage regulator sub-driver
initialization data provides the mapping betten a voltage regulator and what
the output voltage is being used for.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Other sub-drivers for the TPS6507x chip will need to use register
definition so move it out of the source file and into a header file.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On Mon, 2010-05-17 at 17:34 +0200, Mark Brown wrote:
> This doesn't seem like the right error handling - if the driver has a
> set_mode() you'd *expect* it to have a get_mode() but there's no need
> for it to be a strict requirement.
True. In such a case, even a valid request would be lost! So now
in the updated patch:
- check if get_mode is present to avoid oops;
- if get_mode is not present, proceed anyways for the request.
Here is the updated patch:
>From bad0d5eb51ef84be5b100e3dd0f5a590ea0529b6 Mon Sep 17 00:00:00 2001
From: Sundar R Iyer <sundar.iyer@stericsson.com>
Date: Fri, 14 May 2010 15:14:17 +0530
Subject: [PATCH 1/1] regulator: return set_mode when same mode is requested
save I/O costs by returning when the same mode is
requested for the regulator
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds a missing .owner field in regulator_desc, which is used for refcounting.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
All twl6030 regulators can be programmed from 1.0v to 3.3v
with 100mV steps.
The below formula can be used to calculate the vsel values
to be programmed in the VREG_VOLTAGE registers.
Voltage(in mV) = 1000mv + 100mv * (vsel - 1)
Ex: if vsel = 0x9, mV = 1000 + 100 * (9 -1) = 1800mV.
This patch removes all existing VSEL tables for twl6030 adjustable
regulators and just uses the formula directly for vsel calculations
after verifing they fall in the allowed range.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In the case of "min_uV == max_uV == mc13783_regulators[id].voltages[0]",
mc13783_fixed_regulator_set_voltage should return 0 instead of -EINVAL.
This patch also adds a missing ">" character for MODULE_AUTHOR, a trivial fix.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
A lot of condition comparision statements are used in original driver. These
statements are used to check the boundary of voltage numbers since voltage
number isn't linear.
Now use array of voltage numbers instead. Clean code with simpler way.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Remove a lot of driver structures in 88pm860x driver. Make regulators share
one driver structure.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Simply remove all consumer supplies for the regulator on errors. Remove
unset_consumer_device_supply() which is no longer used.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Remove all matching consumer supplies, not just the first, to not leave
dangling pointers.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pointer comparison is not sufficient for non-NULL device name matching,
so use strcmp(). Otherwise the semantics remain the same.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When one regulator supplies another allow the relationship to be specified
using names rather than struct regulators, in a similar manner to that
allowed for consumer supplies. This allows static configuration at compile
time, reducing the need for dynamic init code.
Also change the references to LINE supply to be system supply since line
is sometimes used for actual supplies and therefore potentially confusing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Fix regulator enabling issue that is caused by typo error in is_enabled().
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch fixes a memory leak by freeing priv in mc13783_regulator_remove
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Fix I2C-drivers which missed setting clientdata to NULL before freeing the
structure it points to. Also fix drivers which do this _after_ the structure
was freed already.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Given x=0,1,2, current implementation of BUCK_VOL_CHANGE_SHIFT(x) returns 0,4,8.
The correct return value should be 0,4,6.
This patch fix the logic.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In lp3971_ldo_set_voltage function, it requires val to left shift 4
bits for LDO2 and LDO4.
This patch fix this issue.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
WARNING: at kernel/lockdep.c:2706 sysfs_add_file_mode+0x4c/0xa8()
Difference between v1 and v2:
Moved sysfs_attr_init() call as first one to access the structure.
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
CC: Liam Girdwood <lrg@slimlogic.co.uk>
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Return -ENOMEM if kcalloc() fails
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It is a good tone to reset driver data after unbinding the device.
Also change find_regulator_info() fro inline to __devinit - let compiler
figure out if it wants it to be inlined or not.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8925 contains 3 Buck and 20 LDO regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the support 88PM8607 A0/A1 stepping. There's some register
definition changes in B0 stepping. It can make software more efficient.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rename 88PM8607 to 88PM860X in both Makefile and Kconfig under mfd directory.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88PM8606 and 88PM8607 are two discrete chips used for power management.
Hardware designer can use them together or only one of them according to
requirement.
There's some logic tightly linked between these two chips. For example, USB
charger driver needs to access both chips by I2C interface.
Now share one driver to these two devices. Only one I2C client is identified
in platform init data. If another chip is also used, user should mark it in
companion_addr field of platform init data. Then driver could create another
I2C client for the companion chip.
All I2C operations are accessed by 860x-i2c driver. In order to support both
I2C client address, the read/write API is changed in below.
reg_read(client, offset)
reg_write(client, offset, data)
The benefit is that client drivers only need one kind of read/write API. I2C
and MFD driver can be shared in both 8606 and 8607.
Since API is changed, update API in 8607 regulator driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On Wed, Feb 24, 2010 at 08:40:56PM +0000, Mark Brown wrote:
> On Wed, Feb 24, 2010 at 11:21:26AM -0800, Dmitry Torokhov wrote:
> > On Wed, Feb 24, 2010 at 07:14:03PM +0000, Mark Brown wrote:
>
> > > This doesn't help unless you also provide a way for users to obtain a
> > > struct wm8400.
>
> > Why would they need it? Only code that creates instances of wm8400 needs
> > to know the definition of the sturcture, the rest can simply pass the
> > pointer around.
>
> > I guess there is disconnect between us and I do not see any users of
> > wm8400_register_regulator() in linux-next... Is there another tree I
> > could peek at?
>
> There are no users in mainline. This would be called by board specific
> code from the init callback of the wm8400 - you'd need to pass that
> callback the struct wm8400.
>
> In any case, this is clearly an unrelated change to whatever else you
> were doing to the driver so should be split off into a separate patch,
> but if this is being changed at all then it'd be much more sensible to
> change it to use a more modern pattern which completely removes the
> wm8400_register_regulator() function and just uses platform data.
Fair enough, I removed the offending part, updated patch below.
--
Dmitry
regulator: wm8400 - cleanup platform driver data handling
Driver data set by platform_set_drvdata() is for private use of
the driver currently bound to teh device and not for use by parent,
subsystem and anyone else.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It is a good tone to reset driver data after unbinding the device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It is a good tone to reset driver data after unbinding the device.
Also set up drivers owner.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It is a good tone to reset driver data after unbinding the device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is no point in completing probe if platform data is missing so
let's abort loading early.
Also, use kcalloc when allocating several instances of the same data
structure and mark setup_regulators() as __devinit since it is only
called from lp3971_i2c_probe() which is __devinit.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Also move error handling in probe() out of line and do not bother
to reset fields in structures that are about to be freed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Also move error handling in probe() out of line and do not bother
to reset fields in structures that are about to be freed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add __devinit/__devexit markings to probe and remove methids of the
driver, change types of variables containing boolean data to boolean,
set up driver's owner field so we have proper sysfs link between
driver and the module.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Probe and remove methods should not be marked as __init/__exit but
rather __devinit/__devexit so that the needed sections stay in memory
in presence of CONFIG_HOTPLUG. This is needed even on non hotpluggable
buses.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Instead of open-coding sysfs attribute group use canned solution.
Also add __devinit/__devexit markups for probe and remove methods
and use 'bool' where it makes sense.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is no REMAP register on twl6030, instead there is a STATE register
to drive a resource to a given state.
The state register can be used to specify what state the resource should
enter when its associated with a GRP.
Register Bit field description is as below. The patch programmes the
corresponding STATE registers for all LDO's to turn ON when assocaited
with GRP_P1.
STATE REG:
Bit7 |Bit6 |Bit5 |Bit4 |Bit3 |Bit2 |Bit1 |Bit0
P3_GRP |P2_GRP |P1_GRP |RES |RES |RES |State1 |State0
State can be specified as below
00: OFF
01: ON
10: OFF
11: SLEEP
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In order to ease transitions with drivers are boards start using regulators
provide an option to cause all regulator_get() calls to succeed, with a
dummy always on regulator being supplied where one has not been configured.
A warning is printed whenever the dummy regulator is used to aid system
development.
This regulator does not implement any regulator operations but will allow
simple consumers which only do enable() and disable() calls to run. It
is kept separate from the fixed voltage regulator to avoid Kconfig
confusion on the part of users when it is extended to allow boards to
explicitly use the dummy regulator to simplify cases where the majority
of supplies are from fixed regulators without software control.
This option is currently only effective for systems which do not specify
full constriants. If required an override could also be provided to allow
these systems to use the dummy regulator, though it is likely that
unconfigured supplies on such systems will lead to error due to
regulators being powered down more aggressively when not in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If a regulator driver does not provide a way to query if the driver is
enabled then assume that it is enabled. This is very likely to reflect
the actual state is more useful for callers than reporting an error.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It had an open coded version in enable().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8994 contains two LDOs with mixed hardware/software control to
minimise the number of external supplies required while delivering
optimal voltages to minimise power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix Kconfig text for some Wolfson Micro devices.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
GPO regulators are digital outputs that can be enabled or disabled by a
dedicated bit in mc13783 POWERMISC register.
In this family can be count in also Power Gates (PWGT1 and 2): enabled by
a dedicated pin a Power Gate is an hardware driven supply where the output
(PWGTnDRV) follow this law:
Bit PWGTxSPIEN | Pin PWGTxEN | PWGTxDRV | Read Back
0 = default | | | PWGTxSPIEN
---------------+-------------+----------+------------
1 | x | Low | 0
0 | 0 | High | 1
0 | 1 | Low | 0
As read back value of control bit reflects the PWGTxDRV state (not the
control value previously written) and mc13783 POWERMISC register contain
only regulator related bits, a dedicated function to manage these bits is
created here with the aim of tracing the real value of PWGTxSPIEN bits
and reproduce it on next writes.
All POWERMISC users _must_ use the new function to not accidentally
disable Power Gates supplies.
v2 changes:
-Better utilization of abstraction layers.
-Voltage query support. GPO's and PWGTxDRV are fixed voltage regulator
with voltage value of 3.1V and 5.5V respectively.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add a field to specify a delay for the start-up time of
a fixed voltage regulator.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Regulators may sometimes take longer to enable than the control operation
used to do so, either because the regulator has ramp rate control used to
limit inrush current or because the control operation is very fast (GPIO
being the most common example of this). In order to ensure that consumers
do not rely on the regulator before it is enabled provide an enable_time()
operation and have the core delay for that time before returning to the
caller.
This is implemented as a function since the ramp rate may be specified in
voltage per unit time and therefore the time depend on the configuration.
In future it would be desirable to allow the bulk operations to run the
delays for multiple enables in parallel but this is not currently supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The intended use case is for drivers which disable regulators to save
power but need to do some work to restore the hardware state when
restarting. If the supplies are not actually disabled due to board
limits or sharing with other active devices this notifier allows the
driver to avoid unneeded reinitialisation, particularly when used with
runtime PM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch, complete the mc13783 regulator subsystem driver with
voltage selecting capability.
Main Switches (SW1AB, SW2AB) are not supported yet.
version 2 diffs:
- delete the "Switchers PLL" enable and multiplication factor value
selecting capability because it is not a voltage or current regulator.
This will be a part of Main switcher supporting task.
- Correct many coding style problems pointed me out.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
After `for (val = LDO_VOL_MIN_IDX; val <= LDO_VOL_MAX_IDX; val++)', if no break
occurs, val reaches LDO_VOL_MIN_IDX + 1, which is out of bounds for
ldo45_voltage_map[] and ldo123_voltage_map[].
Similarly BUCK_TARGET_VOL_MAX_IDX + 1 is out of bounds for buck_voltage_map[].
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the regulator constraints are empty and there is no voltage
reported then nothing will be added to the text displayed for the
constraints, leading to random stack data being printed. This is
unlikely to happen for practical regulators since most will at
least report a voltage but should still be fixed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 LED driver needs to be able to enable and disable the
regulators it is using. Previously the core wasn't properly enforcing
status change constraints so the driver was able to function but this
has always been intended to be required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
ret should be signed to notice a failure in wm831x_reg_read().
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This change makes sure all regulator group assignments are cleared on
disable call
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This change implements a basic turnon delay in the regulator enable function
to make it less probable that reg_enable returns before the regulator
output is at target level
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This change ensures the regulator REMAP register configuration is in a known
state so state transitions will function as intended regardless of
possible bootloader effects on it
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This change includes regulator turnon delay values and the REMAP reset
configuration to the twlreg_info struct, since they are basic attributes
of every TWL regulator
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Defines VIO, VDD1, VDD2, VPLL1 and VINT* regulators as always_on by default
since they are critical to TWL and its master's functionality and should
be on in all cases where RegFW is used
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Define all twl4030 regulators in the twlreg_info table, along with
appropriate VSEL tables for adjustable regulators
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When the mc13783-regulator driver is built in kernel, probing it during
the regulator subsystem initialisation result in a fault.
That is because regulator subsystem is planned to be initialised very early
in the boot process, before the mfd subsystem initialisation.
The mc12783-regulator probing process need to access to the mc13783-core
functionality to read/write mc13783 registers and so must be called after
the mc13783-core driver initialisation.
The way to do this is to let the kernel probe the mc13783-regulator driver when
mc13783-core register his regulator subdevice.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently it is possible for regulator_bulk_{enable,disable} operations to
generate unbalanced regulator_{disable,enable} calls in its error path.
In case of an error only those regulators of the bulk operation which actually
had been enabled/disabled should get their original state restored.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
IS_ERR returns only 1 or 0. The callsite of setup_regulators expects a
negative integer in an error case. Thus, PTR_ERR has to be used to extract
it.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E1;
@@
*E = IS_ERR(...)
... when != E = E1
*return E;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
- define needed registers and bits in the driver
- properly namespace functions and structs
- fix locking as required by patch
"mfd/mc13783: near complete rewrite"
- use platform_data as provided by "mfd/mc13783: near complete rewrite"
instead of accessing struct mc13783
- struct mc13783_regulator_priv.desc is (and was) unused and so can go
away
- use cpp magic to initialize mc13783_regulators
- bring MODULE_LICENSE in sync with actual copyright
- minor style fixes
This allows not including mc13783-private.h which I intend to remove
soon.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensoruce.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
One annoying thing about the old name was that the module was just
called mc13783 which caused wrong expectations (at least for me).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensoruce.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch will remove surplus register writes on shut down of
LDO D (this magic was not needed), remove an unnecessary (!) error
check and really unregister the regulators when the module is
unloaded.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If selector equals ARRAY_SIZE(da9034_ldo12_data), that is one too
large already.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If we fall through it means that we hit an unknown regulator/chip
combination so set -ENOENT as an explicit flag (the return code
is only used internally).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
'static const int const' means the same thing as 'static const int'
and sparse complains about this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since some regulators in the system may not support suspend mode
configuration we need to allow some regulators to have a missing
suspend mode configuration. Do this by requiring that disabled
regulators are explicitly flagged and then skip over regulators
that have no state specified.
Try to avoid surprises by warning the if we could set the state
but no configuration is provided. This also ensures that an all
zeros configuration generates a warning rather than silently
disabling the regulator.
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some of the regulator API functions have code to allow the machine
constraints to override the device supplied name for the regulator
in the constraints in order to help tie logging to supplies on the
board and disambiguate when there is more than one regulator chip
in the system. Factor this code out into a new rdev_get_name()
function and use it throughout the regulator API so that we always
use the same name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When voltage or current constraints are either missing or specify
a range display the actual setting along with the constraints if
we can. This can aid debugging of configuration problems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It makes sense to do all the voltage configuration in the one split
out function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This allows constraints to take effect on regulators that support
voltage setting but for which the board does not specify a voltage
range (for example, because it is fixed correctly at system startup).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If we're going to log an error we may as well log what the error
code that we're failing on is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Hi Liam,
Since Samuel merged a new version of mfd 88pm8607 driver, I format a
new patch on regulator 88pm8607. I paste the new patch in mail. Please
help to review again. And I also attach the mfd driver in mail.
From: Haojian Zhuang <haojian.zhuang@marvell.com>
Date: Thu, 8 Oct 2009 09:36:53 -0400
Subject: [PATCH] regulator: Add 88PM8607 PMIC driver
This patch adds regulator drivers for Marvell 88PM8607 PMIC.
This controller contains 3 DVC and 14 LDO regulators. This controller
uses I2C interface.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The BuckWise DC-DC convertors in WM831x devices support switching to
a second output voltage using the logic level on one of the device
pins. This is intended to allow rapid voltage switching for uses like
cpufreq, replacing the I2C or SPI write used to configure the voltage
of the regulator with a much faster GPIO status change.
This is implemented by keeping the DVS voltage configured as the
maximum voltage permitted for the regulator. If a request is made
for the maximum voltage then the GPIO is used to switch to the DVS
voltage, otherwise the normal ON voltage is updated and used. This
follows the idiom used by most cpufreq drivers, which drop the
minimum voltage as the core frequency is dropped but use a constant
maximum - raising the voltage should normally be fast, but lowering
it may be slower.
Configuration of the DVS MFP on the device should be done externally,
for example via OTP.
Support is present in the hardware for monitoring the status of the
transition using a second GPIO. This is not currently implemented
but platform data is provided for it - the driver currently assumes
that the device will be configured to transition immediately - but
platform data is provided to reduce merge issues once it is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Tested with a MX25-based custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch updates the regulator driver to add support
for TWL6030 PMIC specific LDO regulators.
SMPS resources are not yet supported for TWL6030 and
also .set_mode and .get_status for LDO's are yet to
be implemented for TWL6030.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch renames all twl4030_ functions to twl so that regulator driver
can be reused by Triton - TWL4030 and Phoenix - TWL6030.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
