Otherwise we get the following error when enabling CONFIG_SMP
for omap3_defconfig:
arch/arm/kernel/entry-armv.S: Assembler messages:
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ipi r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ltirq r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ipi r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ltirq r0,r6,r5,lr'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Now we use a memory address to store the debug port info, So we need
to read/write this address when we choose DEBUG_LL. When MMU isn't
enable(I.E. the begining part of init stage of the linux kernel boot),
we need to access physical address instead of virtual address,
otherwise the kernel will crash.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds NAND support to ZOOM2 board.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rename board-sdp-flash.c(board-flash.c) and board-sdp.h(board-flash.h) to
used by other board e.g. zoom
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds cpu hotplug support for OMAP4430. Only CPU inactive
state is supported as a low power state in the basic hot-plug support
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves OMAP4 soc specific code from 4430sdp board file.
The change is necessary so that newer board support can be added
with minimal changes. This will be also problematic for
multi-board, multi-omap builds.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Zoom2 and 3 have UARTs only on the external debug board.
GPMC needs to be mapped early to use it for DEBUG_LL.
Additionally, 0xfb000000 overlaps with other areas, so
use 0xfa400000 for the virtual address instead.
Note that with the pending serial.c patches you need to
set console=ttyS0,115200n8 as it will be the only UART
mapped. To use DEBUG_LL, you need to pass also earlyprintk
in cmdline.
Cc: Allen Pais <allen.pais@ti.com>
Acked-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This removes the dependency to the UART1 being available for storing
the debug configuration in uncompress.h. This will simplify the
DEBUG_LL UART configuration for boards that may not have UART1, or
have an external UART as it requires only one mapping for DEBUG_LL.
The patch has a few limitations. Basically now we're assuming that
the kernel uncompress code won't overlap with OMAP_UART_INFO. We also
assume the printascii is called at least once before paging_init in
order for addruart to have a chance to read the UART setup from
OMAP_UART_INFO.
As suggested by Cyril Chemparathy <cyril@ti.com>,
Vikram Pandita <vikram.pandita@ti.com> and
Kevin Hilman <khilman@deeprootsystems.com>. Based on an earlier
patch posted for Davinci by Cyril Chemparathy <cyril@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The value to check is 7 for V6 instead. The code has been
working as it falls through to 24xx code if the other checks
fail.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add base address definations for new AM35xx IPSS modules, like
VPFE, USBOTG, CPGMAC.
Please note that the OMAP34xx IVA2 memory space is being used for
AM35xx IPSS modules.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 'board-sdp-flash.c', which could be utilized
by boards similar to 3430SDP. (For ex: 2430sdp, 36030sdp).
This file does initialization for all three flash devices present
in SDP boards (NOR, NAND, OneNAND), by finding there 'cs' number
dynamically using switch setting information (S8: 1-4).
This also expects partition information from core board files (for
ex: board-3430sdp.c). Which allows to choose different default
partitions for different boards.
A new structure is created for this purpose: 'flash_partitions'
in 'mach/board-sdp.h'. This has two members:
1. struct mtd_partition *parts
2. int nr_parts
A board file is expected to fill this structure and pass it to
'sdp-flsash-init'. Partition information should be passed in
structure array of 'flash_partitions'. Partition information should
be passed in below sequence in array:
NOR
OneNAND
NAND
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow booting omap4 with multi-omap configuration.
Tested only on omap2 and omap3, please somebody test
on omap4 and ack.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move defines around and set up handlers based on MULTI_OMAP2.
Note that this will only allow compiling in omap4 with omap2 and
omap3. It will not yet make omap4 boot with multi-omap.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define the irq base the same way as for omap2 and omap3,
and start using get_irqnr_preamble.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make get_irqnr_and_base common for mach-omap2 multiboot
Thanks to a tip from Russell King <rmk+kernel@arm.linux.org.uk>,
this also optimizes the code for non-multiboot configurations by
using get_irqnr_preamble.
Note that this will only work currently for 24xx and 34xx.
Support for 44xx can be added later on for basic multiboot,
and similar patch should be done for mach-omap1/entry-macro.S.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace zoom2 with zoom name in board-zoom-peripherals.c file
and board-zoom-debugboard.c. Create mach/board-zoom.h.
This file has functions reused for boards: Zoom2/Zoom3/sdp3630.
Hence have all functions commonly named as zoom
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Create the headers needed for compiling under
mach-omap1/include/mach and mach-omap2/include/mach.
This was done with the following script:
#!/bin/bash
mach_files="clkdev.h gpio.h hardware.h io.h irqs.h memory.h \
smp.h system.h timex.h uncompress.h vmalloc.h"
omaps="mach-omap1 mach-omap2"
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
mkdir -p $plat_dir_new
git add $plat_dir_new
for dir in $omaps; do
mach_dir_new="arch/arm/$dir/include/mach"
for header in $mach_files; do
file="$mach_dir_new/$header"
if [ ! -f $file ]; then
echo -ne "/*\n * $file\n */\n\n#include <plat/$header>\n" > $file
git add $file
if [ ! -f $plat_dir_new/$header ]; then
git mv $mach_dir_old/$header $plat_dir_new/$header
fi
fi
done
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Earlier patch "omap: Remap L3, L4 to get more kernel io address space"
changed the VMALLOC_END.
However, this change causes problems on mach-omap1:
BUG: mapping for 0xe0000000 at 0xe0000000 overlaps vmalloc space
BUG: mapping for 0xe1000000 at 0xe1000000 overlaps vmalloc space
Fix this by creating separate vmalloc.h files for mach-omap1
and mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
