For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Based on original implementation from Jiangbi Liu and Maciej Trela.
ATAPI transfers happen in two-to-three stages. The two stage atapi
commands are those that include a dma data transfer. The data transfer
portion of these operations is handled by the hardware packet-dma
acceleration. The three-stage commands do not have a data transfer and
are handled without hardware assistance in raw frame mode.
stage1: transmit host-to-device fis to notify the device of an incoming
atapi cdb. Upon reception of the pio-setup-fis repost the task_context
to perform the dma transfer of the cdb+data (go to stage3), or repost
the task_context to transmit the cdb as a raw frame (go to stage 2).
stage2: wait for hardware notification of the cdb transmission and then
go to stage 3.
stage3: wait for the arrival of the terminating device-to-host fis and
terminate the command.
To keep the implementation simple we only support ATAPI packet-dma
protocol (for commands with data) to avoid needing to handle the data
transfer manually (like we do for SATA-PIO). This may affect
compatibility for a small number of devices (see
ATA_HORKAGE_ATAPI_MOD16_DMA).
If the data-transfer underruns, or encounters an error the
device-to-host fis is expected to arrive in the unsolicited frame queue
to pass to libata for disposition. However, in the DONE_UNEXP_FIS (data
underrun) case it appears we need to craft a response. In the
DONE_REG_ERR case we do receive the UF and propagate it to libsas.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The queue-depth for libsas-attached devices initializes to 32 and can
only be increased manually via sysfs to a max of 64, while mpt2sas
attached devices initialize to 254 and dynamically float via the
midlayer ->change_queue_depth interface.
No performance regression was observed with this change on the isci
driver.
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pass queue_depth change requests to libata, and prevent queue_type
changes for ATA devices.
Otherwise:
1/ we do not honor the libata specific restrictions on the queue depth
2/ libsas drivers that do not set sdev->tagged_supported are unable to
change the queue_depth of ata devices via sysfs
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
->queuecommand must return either 0, or one of the SCSI_MLQUEUE_* return
values. Non-transient errors are indicated by setting cmd->result before
calling ->scsi_done and returning 0. Fix libsas to adhere to this calling
convention. Note that the DID_ERROR for returns from the low-level driver
might not be correct for all cases, but it's the best we can do with
the current layering in libsas. I also suspect that the pre-existing
handling of -SAS_QUEUE_FULL should really be SCSI_MLQUEUE_HOST_BUSY, but
I'll leave that for a separate change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Switch sas_queuecommand to a normal indentation and goto based error handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Head off doomed-to-fail i/o in sas_queuecommand before sending it down
the ata path.
Before:
sd 7:0:0:0: [sdd] Synchronizing SCSI cache
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
sd 7:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 7:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
sd 7:0:0:0: [sdd] Add. Sense: No additional sense information
sd 7:0:0:0: [sdd] Stopping disk
After:
sd 9:0:0:0: [sdd] Synchronizing SCSI cache
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 9:0:0:0: [sdd] Stopping disk
sd 9:0:0:0: [sdd] START_STOP FAILED
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
This is a cosmetic change as sata i/o can still leak to a gone device,
but this addresses the nominal hotplug case when releasing the target.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling. The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.
Finally, activate the port recovery of the libata error handler for
each port known to the host. This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling. The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.
Finally, activate the port recovery of the libata error handler for
each port known to the host. This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine. Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system). The fix is to clear the
flag as we splice the work queue.
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sd will get hung up issuing commands to flush write cache if a SAS
device behind the expander is unplugged without warning. Change libsas
to reject commands to domain devices that have already gone away.
[maciej.trela@intel.com: removed setting ->gone in sas_deform_port() to
permit sync cache commands at module removal]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Tested-by: Haipao Fan <haipao.fan@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
REQ_HARDBARRIER is deprecated. Remove spurious uses in the following
users. Please note that other than osdblk, all other uses were
already spurious before deprecation.
* osdblk: osdblk_rq_fn() won't receive any request with
REQ_HARDBARRIER set. Remove the test for it.
* pktcdvd: use of REQ_HARDBARRIER in pkt_generic_packet() doesn't mean
anything. Removed.
* aic7xxx_old: Setting MSG_ORDERED_Q_TAG on REQ_HARDBARRIER is
spurious. Removed.
* sas_scsi_host: Setting TASK_ATTR_ORDERED on REQ_HARDBARRIER is
spurious. Removed.
* scsi_tcq: The ordered tag path wasn't being used anyway. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We have two separate definitions for identical constants with nearly the
same name. One comes from the generic headers in scsi.h; the other is
an enum in libsas.h ... it's causing confusion about which one is
correct (fortunately they both are).
Fix this by eliminating the libsas.h duplicate
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
[SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
[SCSI] aacraid: prohibit access to array container space
[SCSI] aacraid: add support for handling ATA pass-through commands.
[SCSI] aacraid: expose physical devices for models with newer firmware
[SCSI] aacraid: respond automatically to volumes added by config tool
[SCSI] fcoe: fix fcoe module ref counting
[SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
[SCSI] libfcoe: Fix incorrect MAC address clearing
[SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
[SCSI] libfc: Move the port_id into lport
[SCSI] fcoe: move link speed checking into its own routine
[SCSI] libfc: Remove extra pointer check
[SCSI] libfc: Remove unused fc_get_host_port_type
[SCSI] fcoe: fixes wrong error exit in fcoe_create
[SCSI] libfc: set seq_id for incoming sequence
[SCSI] qla2xxx: Updates to ISP82xx support.
[SCSI] qla2xxx: Optionally disable target reset.
[SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
[SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
[SCSI] qla2xxx: T10 DIF support added.
...
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken. Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.
Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead. ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.
This simplifies condition check in IRQ handlers. While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit 70b25f890c
Author: Tejun Heo <tj@kernel.org>
Date: Thu Apr 15 09:00:08 2010 +0900
[SCSI] fix locking around blk_abort_request()
Introduced a reference before check problem, fix this by moving the
lock shorthand code to be right at the point of actual use.
Reported-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
blk_abort_request() expects queue lock to be held by the caller.
Grab it before calling the function.
Lack of this synchronization led to infinite loop on corrupt
q->timeout_list.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Provide a facility to use the request_firmware() interface to get a SAS
address from userspace. This can be used by SAS LLDDs that cannot
obtain the address from the host adapter.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Correct one use after free of the sas task
- update the reset required path to move straight to LUN reset
- make the bigger hammer actually reset something instead of just trying
to clear all the tasks.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is needed by the to be added I_T reset function in aic94xx. It
needs to know the local phy so it can send a link or hard reset along
the path.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current sas_scsi_clear_queue_lu() is wrongly checking for commands
which match the pointer to the one passed in. It should be checking for
commands which are on the same logical unit as the one passed in. Fix
this by checking target pointer and LUN for equality.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The libsas error handler has two fairly fatal bugs
1. scsi_sas_task_done calls scsi_eh_finish_cmd() too early. This
happens if the task completes after it has been aborted but before
the error handler starts up. Because scsi_eh_finish_cmd()
decrements host_failed and adds the task to the done list, the
error handler start check (host_failed == host_busy) never passes
and the eh never starts.
2. The multiple task completion paths sas_scsi_clear_queue_... all
simply delete the task from the error queue. This causes it to
disappear into the ether, since a command must be placed on the
done queue to be finished off by the error handler. This behaviour
causes the HBA to hang on pending commands.
Fix 1. by moving the SAS_TASK_STATE_ABORTED check to an exit clause at
the top of the routine and calling ->scsi_done() unconditionally (it
is a nop if the timer has fired). This keeps the task in the error
handling queue until the eh starts.
Fix 2. by making sure every task goes through task complete followed
by scsi_eh_finish_cmd().
Tested this by firing resets across a disk running a hammer test (now
it actually survives without hanging the system)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
LLDs don't need to zero out scsi_cmnd::sense_buffer in queuecommand
since scsi-ml does. This is a preparation of the future changes to
allocate the sense_buffer only when necessary.
Many LLDs zero out the sense_buffer before touching it on the error
case. This patch lets them alone for now because new APIs for them
would be added later on.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: "Salyzyn, Mark" <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Annotate sas_queuecommand with locking details, and clean up a few
more sparse warnings about static/non-static declarations.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ATA devices need special handling for sas_task_abort. If the ATA command
came from SCSI, then we merely need to tell SCSI to abort the scsi_cmnd.
However, internal commands require a bit more work--we need to fill the qc
with the appropriate error status and complete the command, and eventually
post_internal will issue the actual ABORT TASK.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ata_qc_complete and ata_sas_queuecmd require that the port lock be held
when they are called. sas_ata doesn't do this, leading to BUG messages
about qc tags newly allocated qc tags already being in use. This patch
fixes the locking, which should clean up the rest of those messages.
So far I've tested this against an IBM x206m with two SATA disks with no
BUG messages and no other signs of things going wrong, and the machine
finally passed the pounder stress test.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a respin of my earlier patch that migrates the ATA support code
into a separate file. For now, the controversial linking bits have
been removed per James Bottomley's request for a patch that contains
only the migration diffs, which means that libsas continues to require
libata. I intend to address that problem in a separate patch.
This patch is against the aic94xx-sas-2.6 git tree, and it has been
sanity tested on my x206m with Seagate SATA and SAS disks without
uncovering any new problems.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We actually had two problems: the one with the tag (which is fixed by
zeroing the tag before sending the taskfile to the sequencer) but the
other with the fact that we sent our first NCQ command to the device
before the sequencer had been informed of the NCQ tagging
capabilities. I fixed the latter by moving the rphy_add() to the
correct point in the code after the NCQ capabilities are set up.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It turns out this is fairly easy to plumb in by recognising the three
command types and copying the CDB. The protocol response path needs to
be amended to cope with SAS_PROTO_RESPONSE.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds SATAII NCQ support to libsas. Both the use_ncq and the
dma_xfer flags in ata_task must be set for NCQ to work correctly on the
Adaptec SAS controller. The rest of the patch adds ATA_FLAG_NCQ to
sata_port_info and sets up ap->scsi_host so that ata_setup_ncq doesn't
crash. Please note that this patch is against the aic94xx-sas git tree,
not scsi-misc. Thanks also to James Bottomley for providing an earlier
version of this patch from which to work.
I've tested this patch on a x206m with a ST380819AS SATA2 disk plugged
into the Adaptec SAS controller. The drive came up with a queue depth
of 31, and I successfully ran an I/O flood test to coerce libata into
sending multiple commands simultaneously. A kernel probe recorded the
maximum tag number that had been seen before and after the flood test;
before the test it was 2 and after it was 30, as I expected.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hook the scsi_host_template functions in libsas to delegate
functionality to libata when appropriate.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Misc code changes and merge fixes and update for libata->drivers/ata
move
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After discussion with andmike and dougg, it seems that the purpose of
eh_device_reset_handler is to issue LU resets, and that
eh_bus_reset_handler would be a more appropriate place for a phy reset.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Set allow_restart=1 for all SAS disks so that they are spun up when needed.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Paul Gortmaker