[ Upstream commit 03976af89e ]
Else there may be a double-free problem, because cfi->cfiq will
be freed by mtd_do_chip_probe() if both the two invocations of
check_cmd_set() return failure.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c15995695e upstream.
The commit 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling
status register") added checking for the status register error bits into
chip_good() to only return 1 if these bits are 0s. Unfortunately, this
means that polling using chip_good() always reaches a timeout condition
when erase or program failure bits are set. Let's fully delegate the task
of determining the error conditions to cfi_check_err_status() and make
chip_good() only look for the Device Ready/Busy condition.
Fixes: 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling status register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72914a8cff upstream.
Cypress S26K{L|S}P{128|256|512}S datasheet says that the error bits in
the status register are only valid when the "device ready" bit 7 is set.
Add the check for the device ready bit in cfi_check_err_status() as that
function isn't always called with this bit set.
Fixes: 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling status register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chip state is set to erasing by the function after getting chip.
So it should be to get chip as erasing mode at first.
But previously it was to get chip as writing mode then fix as erasing.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Some write buffer functions are not used when FORCE_WORD_WRITE is set to 1.
So the compile warning messages are output if FORCE_WORD_WRITE is 1. To
resolve this disable the write buffer functions if FORCE_WORD_WRITE is 1.
Cc: Fabio Bettoni <fbettoni@gmail.com>
Co: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The do_write_oneword_done() is called twice at the exit paths.
By splitting the retry functionality it can be reduced to call once.
Cc: Fabio Bettoni <fbettoni@gmail.com>
Co: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
To reduce function size and to remove the goto statement, split the
op_done goto statement part into do_write_oneword_done(). Also
split the start part into do_write_oneword_start() to be symmetrical.
Cc: Fabio Bettoni <fbettoni@gmail.com>
Co: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
[vigneshr@ti.com: Reword commit message]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reduce the size of do_write_oneword() by extracting a helper function
for the hardware access.
Cc: Fabio Bettoni <fbettoni@gmail.com>
Co: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
As reported by the OpenWRT team, write requests sometimes fail on some
platforms.
Currently to check the state chip_ready() is used correctly as described by
the flash memory S29GL256P11TFI01 datasheet.
Also chip_good() is used to check if the write is succeeded and it was
implemented by the commit fb4a90bfcd ("[MTD] CFI-0002 - Improve error
checking").
But actually the write failure is caused on some platforms and also it can
be fixed by using chip_good() to check the state and retry instead.
Also it seems that it is caused after repeated about 1,000 times to retry
the write one word with the reset command.
By using chip_good() to check the state to be done it can be reduced the
retry with reset.
It is depended on the actual flash chip behavior so the root cause is
unknown.
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Reported-by: Fabio Bettoni <fbettoni@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
[vigneshr@ti.com: Fix a checkpatch warning]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The 'mtd' local variable is initialized but this value is never used,
thus kill that initializer.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0fxH8ACgkQJWrqGEe9
VoRq5wgApOTmT44UiI3XHQZMWANcW5/DkNwXEzXtdRQJHv1m3eqny1faGOYJZifZ
eb0TpohK0783L4STii7g1iplBA+c8UGJaS1bpn9HoN3us8wxXn51fzHHj5G3z2tR
xoyaEm7w7dZuqe/FLCW+MbtOREAq1GzullVZxrd75wxNyK3cQXawqYDsil6I5fl7
sf2zMzfzfGK6LqbapOHorxyI8yJR712TLPwBq7amHpPZMXOny0gIlYVXLv6jYAfr
3RcW0YpyplBjLAFKBOpVLPJ61c9NVQSsdQ2wviRckhrMgCD83f7YDmAACxM0rvSz
lVYcHHqoqYHlTDPVBebeoifQOb4uUw==
=I5Hg
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command
Set (0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.c can be used as is. But these devices
do not support DQ polling method of determining chip ready/good status.
These flashes provide Status Register whose bits can be polled to know
status of flash operation.
Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu
Extended Query version 1.5. Bit 0 of "Software Features supported" field
of CFI Primary Vendor-Specific Extended Query table indicates
presence/absence of status register and Bit 1 indicates whether or not
DQ polling is supported. Using these bits, its possible to determine
whether flash supports DQ polling or need to use Status Register.
Add support for polling Status Register to know device ready/status of
erase/write operations when DQ polling is not supported.
Print error messages on erase/program failure by looking at related
Status Register bits.
[1] https://www.cypress.com/file/213346/download
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Because PPB unlocking unlocks the whole chip cfi_ppb_unlock() needs to
remember the locked status for each sector so it can re-lock the
unaddressed sectors. Dynamically calculate the maximum number of sectors
rather than using a hardcoded value that is too small for larger chips.
Tested with Spansion S29GL01GS11TFI flash device.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mtd/chips/cfi_cmdset_0002.c: In function ‘get_chip’:
drivers/mtd/chips/cfi_cmdset_0002.c:870:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (mode == FL_READY && chip->oldstate == FL_READY)
^
drivers/mtd/chips/cfi_cmdset_0002.c:873:2: note: here
default:
^~~~~~~
drivers/mtd/chips/cfi_cmdset_0002.c: In function ‘cfi_amdstd_sync’:
drivers/mtd/chips/cfi_cmdset_0002.c:2745:16: warning: this statement may fall through [-Wimplicit-fallthrough=]
chip->state = FL_SYNCING;
~~~~~~~~~~~~^~~~~~~~~~~~
drivers/mtd/chips/cfi_cmdset_0002.c:2750:3: note: here
case FL_SYNCING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mtd/chips/cfi_util.c: In function ‘cfi_build_cmd’:
drivers/mtd/chips/cfi_util.c:110:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
onecmd |= (onecmd << (chip_mode * 32));
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/chips/cfi_util.c:112:2: note: here
case 4:
^~~~
drivers/mtd/chips/cfi_util.c:113:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
onecmd |= (onecmd << (chip_mode * 16));
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/chips/cfi_util.c:114:2: note: here
case 2:
^~~~
drivers/mtd/chips/cfi_util.c: In function ‘cfi_merge_status’:
drivers/mtd/chips/cfi_util.c:163:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
res |= (onestat >> (chip_mode * 32));
~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/chips/cfi_util.c:165:2: note: here
case 4:
^~~~
drivers/mtd/chips/cfi_util.c:166:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
res |= (onestat >> (chip_mode * 16));
~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/chips/cfi_util.c:167:2: note: here
case 2:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
In function do_write_buffer(), in the for loop, there is a case
chip_ready() returns 1 while chip_good() returns 0, so it never
break the loop.
To fix this, chip_good() is enough and it should timeout if it stay
bad for a while.
Fixes: dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
Signed-off-by: Yi Huaijie <yihuaijie@huawei.com>
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Tokunori Ikegami <ikegami_to@yahoo.co.jp>
Signed-off-by: Richard Weinberger <richard@nod.at>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114857 ("Missing break in switch")
Addresses-Coverity-ID: 114858 ("Missing break in switch")
Addresses-Coverity-ID: 114859 ("Missing break in switch")
Addresses-Coverity-ID: 114860 ("Missing break in switch")
Addresses-Coverity-ID: 114861 ("Missing break in switch")
Addresses-Coverity-ID: 114862 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJbYYGVAAoJECVq6hhHvVaE0poIAJy+VpZl0jTPQ/oO8TQui9hE
IZbc8LwohCvegYYhiY1cNESyMYamDfoK6M93i/0zTJF2AJAxPl25ldT8N5Wr16DO
5Vfsdjv75V8l0JEY2SvWYmC6glOAYs0UEDdcFNJRMPqUnQz+VvBIafJOCQqzo4ZH
SDnLx3XzOxO4PAPnztWEg50WvaqMPt7ThcqoxThHMcQaLrNjgJUsV0mN+vNEv16Q
6gH6hl1C019k+Kj2Zu0vAifHw1K7gIYT4HvqKwstQ6HYUX2IzIzuEpRIcIze0S5z
XKzZ57USItb3l+Y3YwFBLjgP4N+VTT5X59LxdtCOXJ+YvzgxwtKElRvalNcryYI=
=zkEf
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.19' of git://git.infradead.org/linux-mtd into mtd/next
Pull NAND updates from Miquel Raynal:
"
NAND core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
"
Fix indentation and replace '---help---' by 'help' to make things
consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Variable is_local is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'timeo' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Using "%4.4X" in the calculation of the buffer size is misleading, as
the format string literal has no relation to the actual size needed.
Hence this is fragile w.r.t. future modification.
As this is not a hot path, fix this by replacing the formatting in a
fixed buffer by kasprintf().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
With the special case handling for Blackfin and Metag was removed by
commit 94e58e0ac3 ("export.h: remove code for prefixing symbols with
underscore"), VMLINUX_SYMBOL_STR() can be replaced with string literal.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The "sector is in requested range" test used to determine whether
sectors should be re-locked or not is done on a variable that is reset
everytime we cross a chip boundary, which can lead to some blocks being
re-locked while the caller expect them to be unlocked.
Fix the check to make sure this cannot happen.
Fixes: 1648eaaa15 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking")
Cc: stable@vger.kernel.org
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
cfi_ppb_unlock() tries to relock all sectors that were locked before
unlocking the whole chip.
This locking used the chip start address + the FULL offset from the
first flash chip, thereby forming an illegal address. Fix that by using
the chip offset(adr).
Fixes: 1648eaaa15 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking")
Cc: stable@vger.kernel.org
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
do_ppb_xxlock() fails to add chip->start when querying for lock status
(and chip_ready test), which caused false status reports.
Fix that by adding adr += chip->start and adjust call sites
accordingly.
Fixes: 1648eaaa15 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking")
Cc: stable@vger.kernel.org
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND changes:
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR changes:
Core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
* Mark the driver as "dangerous" in Kconfig
* Fix atomic sequence handling
* Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
* fix a typo in a function name
* add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line
-----BEGIN PGP SIGNATURE-----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=cHjU
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
To enable XIP it is executed both normal and error cases.
This call can be moved after the for loop as same with erase chip.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently the functions use to check both chip ready and good.
But the chip ready is not enough to check the operation status.
So change this to check the chip good instead of this.
About the retry functions to make sure the error handling remain it.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
For the word write functions it is retried for error.
But it is not implemented to retry for the erase functions.
To make sure for the erase functions change to retry as same.
This is needed to prevent the flash erase error caused only once.
It was caused by the error case of chip_good() in the do_erase_oneblock().
Also it was confirmed on the MACRONIX flash device MX29GL512FHT2I-11G.
But the error issue behavior is not able to reproduce at this moment.
The flash controller is parallel Flash interface integrated on BCM53003.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The definition can be used for other program and erase operations also.
So change the naming to MAX_RETRIES from MAX_WORD_RETRIES.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
For the word write it is checked if the chip has the correct value.
But it is not checked for the write buffer as only checked if ready.
To make sure for the write buffer change to check the value.
It is enough as this patch is only checking the last written word.
Since it is described by data sheets to check the operation status.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This patch fixes mainly to remove unneeded spaces after '(' and before ')'.
Also some indentation errors are fixed.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
S70GL02GS flash reports a single 256 MiB chip, but is really made up
of two 128 MiB chips with 1024 sectors each.
Without early fixups (top half of device cannot be written or erased):
ff0000000.nor-boot: Found 1 x16 devices at 0x0 in 16-bit bank. <snip>
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.5.
number of CFI chips: 1
With early fixups (entire device can be written and erased):
Bad S70GL02GS CFI data; adjust to detect 2 chips
ff0000000.nor-boot: Found 1 x16 devices at 0x0 in 16-bit bank. <snip>
ff0000000.nor-boot: Found 1 x16 devices at 0x8000000 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.5.
number of CFI chips: 2
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some CFI devices need fixups that affect the number of chips detected,
but the current fixup infrastructure (struct cfi_fixup and cfi_fixup())
does not cover this situation.
Introduce struct cfi_early_fixup and cfi_early_fixup() to fill the void.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently it is possible to read and/or write to suspend EB's.
Writing /dev/mtdX or /dev/mtdblockX from several processes may
break the flash state machine.
Taken from cfi_cmdset_0001 driver.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some Micron chips does not work well wrt Erase suspend for
boot blocks. This avoids the issue by not allowing Erase suspend
for the boot blocks for the 28F00AP30(1GBit) chip.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently it is possible to read and/or write to suspend EB's.
Writing /dev/mtdX or /dev/mtdblockX from several processes may
break the flash state machine.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Core:
* Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
* Remove Cyrille from the list of SPI NOR and MTD maintainers
* Fix kernel doc headers
* Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
* Remove the bfin-async-flash driver (the only architecture using
it has been removed)
* Fix pagetest test
* Add extra checks in mtd_erase()
* Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
Drivers:
* Add endianness information to the physmap DT binding
* Add Eon EN29LV400A IDs to JEDEC probe logic
* Use %*ph where appropriate
SPI NOR changes:
Drivers:
* Make fsl-quaspi assign different names to MTD devices connected
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND changes:
Core:
* Prepare arrival of the SPI NAND subsystem by implementing a
generic (interface-agnostic) layer to ease manipulation of NAND
devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Drivers:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----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=EG7L
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD Core:
- Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
- Remove Cyrille from the list of SPI NOR and MTD maintainers
- Fix kernel doc headers
- Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
- Remove the bfin-async-flash driver (the only architecture using it
has been removed)
- Fix pagetest test
- Add extra checks in mtd_erase()
- Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
MTD Drivers:
- Add endianness information to the physmap DT binding
- Add Eon EN29LV400A IDs to JEDEC probe logic
- Use %*ph where appropriate
SPI NOR Drivers:
- Make fsl-quaspi assign different names to MTD devices connected to
the same QSPI controller
- Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND Core:
- Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
- Move onenand code base to the drivers/mtd/nand/ dir
- Rework timing mode selection
- Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
- Stop embedding ONFI/JEDEC param page in nand_chip
NAND Drivers:
- Rework/cleanup of the mxc driver
- Various cleanups in the vf610 driver
- Migrate the fsmc and vf610 to ->exec_op()
- Get rid of the pxa driver (replaced by marvell_nand)
- Support ->setup_data_interface() in the GPMI driver
- Fix probe error path in several drivers
- Remove support for unused hw_syndrome mode in sunxi_nand
- Various minor improvements"
* tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd: (89 commits)
dt-bindings: fsl-quadspi: Add the example of two SPI NOR
mtd: fsl-quadspi: Distinguish the mtd device names
mtd: nand: Fix some function description mismatches in core.c
mtd: fsl-quadspi: Remove unneeded driver.bus assignment
mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk
mtd: rawnand: s3c2410: enhance the probe function error path
mtd: rawnand: tango: fix probe function error path
mtd: rawnand: sh_flctl: fix the probe function error path
mtd: rawnand: omap2: fix the probe function error path
mtd: rawnand: mxc: fix probe function error path
mtd: rawnand: denali: fix probe function error path
mtd: rawnand: davinci: fix probe function error path
mtd: rawnand: cafe: fix probe function error path
mtd: rawnand: brcmnand: fix probe function error path
mtd: rawnand: sunxi: Stop supporting ECC_HW_SYNDROME mode
mtd: rawnand: marvell: Fix clock resource by adding a register clock
mtd: ftl: Use DIV_ROUND_UP()
mtd: Fix some function description mismatches in mtdcore.c
mtd: physmap_of: update struct map_info's swap as per map requirement
dt-bindings: mtd-physmap: Add endianness supports
...
It turns out that the loop where we read manufacturer
jedec_read_mfd() can under some circumstances get a
CFI_MFR_CONTINUATION repeatedly, making the loop go
over all banks and eventually hit the end of the
map and crash because of an access violation:
Unable to handle kernel paging request at virtual address c4980000
pgd = (ptrval)
[c4980000] *pgd=03808811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] PREEMPT ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc1+ #150
Hardware name: Gemini (Device Tree)
PC is at jedec_probe_chip+0x6ec/0xcd0
LR is at 0x4
pc : [<c03a2bf4>] lr : [<00000004>] psr: 60000013
sp : c382dd18 ip : 0000ffff fp : 00000000
r10: c0626388 r9 : 00020000 r8 : c0626340
r7 : 00000000 r6 : 00000001 r5 : c3a71afc r4 : c382dd70
r3 : 00000001 r2 : c4900000 r1 : 00000002 r0 : 00080000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 0000397f Table: 00004000 DAC: 00000053
Process swapper (pid: 1, stack limit = 0x(ptrval))
Fix this by breaking the loop with a return 0 if
the offset exceeds the map size.
Fixes: 5c9c11e1c4 ("[MTD] [NOR] Add support for flash chips with ID in bank other than 0")
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This adds the JEDEC IDs for Eon EN29LV400A variants
EN29LV400AB and EN29LV400AT. This chip is found in the
D-Link DNS-313.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Hou Tao