This contains board-specific portion to respect driver changes (for 8272ads ,
885ads and 866ads). Altered platform_data structures as well as initial setup
routines relevant to fs_enet.
Changes to the mpc8560ads ppc/ code are also introduced, but mainly as
reference, since the entire board support is going to appear in arch/powerpc.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This makes it possible for HW PHY-less boards to utilize PAL goodies. Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc. information into PHY
descriptor (the latter feature not tested so far).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from Paul Gortmaker
Some folks here at Wind River asked me if I'd push this out
so that the value was generally agreed upon in advance by
all folks interested in working with iWMMXt. Seems simple
enough...
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
A number of small issues with the S3C24XX DMA have
cropped up, which this patch fixes. These are:
- check wether we can load another buff in start
- update state handling in s3c2410_dma_lastxfer
- only reload in irq if channel is not idle
- more informative timeout errors (add source)
- do not call request_irq() with irqs locked
- added waitforstop function
The patch also adds a S3C2410_DMAOP_STARTED for
the occasions when the driver wants to ensure that
the DMA system load state is resynced after loading.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the bridge recomputes features, it does not maintain the
constraint that SG/GSO must be off if TX checksum is off.
This patch adds that constraint.
On a completely unrelated note, I've also added TSO6 and TSO_ECN
feature bits if GSO is enabled on the underlying device through
the new NETIF_F_GSO_SOFTWARE macro.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since __vlan_hwaccel_rx() is essentially bypassing the
netif_receive_skb() call that would have occurred if we did the VLAN
decapsulation in software, we are missing the skb_bond() call and the
assosciated checks it does.
Export those checks via an inline function, skb_bond_should_drop(),
and use this in __vlan_hwaccel_rx().
Signed-off-by: David S. Miller <davem@davemloft.net>
To compile kexec on 32-bit we need a few more bits and pieces. Rather
than add empty definitions, we can make crash.c work on 32-bit, with
only a couple of kludges.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Atmel flash chips don't have PRI information in the same format as
AMD flash chips. This patch installs a fixup for all Atmel chips that
converts the relevant PRI fields into AMD format.
Only the fields that are actually used by the command set is actually
converted. The rest are initialized to zero (which should be safe)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Don't let fuse_readpages leave the @pages list not empty when exiting
on error.
[akpm@osdl.org: kernel-doc fixes]
Signed-off-by: Alexander Zarochentsev <zam@namesys.com>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
linux/backlight.h pulls in header files (eg. ioport.h) that break
compilation of userspace programs. To solve the problem, only include
backlight.h in fb.h if compiling kernel stuff.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The IPv4/IPv6 datagram output path was using skb_trim to trim paged
packets because they know that the packet has not been cloned yet
(since the packet hasn't been given to anything else in the system).
This broke because skb_trim no longer allows paged packets to be
trimmed. Paged packets must be given to one of the pskb_trim functions
instead.
This patch adds a new pskb_trim_unique function to cover the IPv4/IPv6
datagram output path scenario and replaces the corresponding skb_trim
calls with it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
pr_debug() should not be used from drivers, add comment saying that.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jack Steiner identified a problem where XPC can cause a silent
data corruption. On module load, the placement may cause the
xpc_remote_copy_buffer to span two physical pages. DMA transfers are
done to the start virtual address translated to physical.
This patch changes the buffer from a statically allocated buffer to a
kmalloc'd buffer. Dean Nelson reviewed this before posting. I have
tested it in the configuration that was showing the memory corruption
and verified it works. I also added a BUG_ON statement to help catch
this if a similar situation is encountered.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This adds a shadow buffer for the SLBs and regsiters it with PHYP.
Only the bolted SLB entries (top 3) are shadowed.
The SLB shadow buffer tells the hypervisor what the kernel needs to
have in the SLB for the kernel to be able to function. The hypervisor
can use this information to speed up partition context switches.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't have much in the way of doc comments, but some of those we do have
don't work because they start with "/***" or "/*", not "/**" which is what
kernel-doc requires.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Noticing the following might_sleep warning (dump_stack()) during kdump
testing when CONFIG_DEBUG_SPINLOCK_SLEEP is enabled. All secondary CPUs
will be calling rtas_set_indicator with interrupts disabled to remove
them from global interrupt queue.
BUG: sleeping function called from invalid context at
arch/powerpc/kernel/rtas.c:463
in_atomic():1, irqs_disabled():1
Call Trace:
[C00000000FFFB970] [C000000000010234] .show_stack+0x68/0x1b0 (unreliable)
[C00000000FFFBA10] [C000000000059354] .__might_sleep+0xd8/0xf4
[C00000000FFFBA90] [C00000000001D1BC] .rtas_busy_delay+0x20/0x5c
[C00000000FFFBB20] [C00000000001D8A8] .rtas_set_indicator+0x6c/0xcc
[C00000000FFFBBC0] [C000000000048BF4] .xics_teardown_cpu+0x118/0x134
[C00000000FFFBC40] [C00000000004539C]
.pseries_kexec_cpu_down_xics+0x74/0x8c
[C00000000FFFBCC0] [C00000000002DF08] .crash_ipi_callback+0x15c/0x188
[C00000000FFFBD50] [C0000000000296EC] .smp_message_recv+0x84/0xdc
[C00000000FFFBDC0] [C000000000048E08] .xics_ipi_dispatch+0xf0/0x130
[C00000000FFFBE50] [C00000000009EF10] .handle_IRQ_event+0x7c/0xf8
[C00000000FFFBF00] [C0000000000A0A14] .handle_percpu_irq+0x90/0x10c
[C00000000FFFBF90] [C00000000002659C] .call_handle_irq+0x1c/0x2c
[C00000000058B9C0] [C00000000000CA10] .do_IRQ+0xf4/0x1a4
[C00000000058BA50] [C0000000000044EC] hardware_interrupt_entry+0xc/0x10
--- Exception: 501 at .plpar_hcall_norets+0x14/0x1c
LR = .pseries_dedicated_idle_sleep+0x190/0x1d4
[C00000000058BD40] [C00000000058BDE0] 0xc00000000058bde0 (unreliable)
[C00000000058BDF0] [C00000000001270C] .cpu_idle+0x10c/0x1e0
[C00000000058BE70] [C000000000009274] .rest_init+0x44/0x5c
To fix this issue, rtas_set_indicator_fast() is added so that will not
wait for RTAS 'busy' delay and this new function is used for kdump (in
xics_teardown_cpu()) and for CPU hotplug ( xics_migrate_irqs_away() and
xics_setup_cpu()).
Note that the platform architecture spec says that set-indicator
on the indicator we're using here is not permitted to return the
busy or extended busy status codes.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Conflicts:
arch/ia64/hp/sim/simscsi.c
Stylistic differences in two separate fixes for buffer->request_buffer
problem.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The per cpu variables are used incorrectly in vmstat.h.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Acked-by: Steve Fox <drfickle@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It should be possible to suspend, either to RAM or to disk, if there's a
traced process that has just reached a breakpoint. However, this is a
special case, because its parent process might have been frozen already and
then we are unable to deliver the "freeze" signal to the traced process.
If this happens, it's better to cancel the freezing of the traced process.
Ref. http://bugzilla.kernel.org/show_bug.cgi?id=6787
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Overflow can occur very easily with 32 bits, e.g., with 1 second
us_idle is approx. 2^20, which leaves only 11-Wlog bits for queue
length. Since the EWMA exponent is typically around 9, queue
lengths larger than 2^2 cause overflow. Whether the affected
branch is taken when us_idle is as high as 1 second, depends on
Scell_log, but with rather reasonable configuration Scell_log is
large enough to cause p->Stab to have zero index, which always
results zero shift (typically also few other small indices result
in zero shift).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'fixes' of git://git.linux-nfs.org/pub/linux/nfs-2.6:
SUNRPC: Fix obvious refcounting bugs in rpc_pipefs.
RPC: Ensure that we disconnect TCP socket when client requests error out
NLM/lockd: remove b_done
NFS: make 2 functions static
NFS: Release dcache_lock in an error path of nfs_path
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PNP: Add missing casts in printk() arguments
PCI: docking station: remove dock uevents
PCI: Unhide the SMBus on Asus PU-DLS
PCI Hotplug: add acpiphp to MAINTAINERS
PCI: pci/search: EXPORTs cannot be __devinit
PCIE: cleanup on probe error
pcie: fix warnings when CONFIG_PM=n
If we're part way through transmitting a TCP request, and the client
errors, then we need to disconnect and reconnect the TCP socket in order to
avoid confusing the server.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
(cherry picked from 031a50c8b9ea82616abd4a4e18021a25848941ce commit)
We never actually set the b_done field any more; it's always zero.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
(cherry picked from af8412d4283ef91356e65e0ed9b025b376aebded commit)
nfs_writedata_free() and nfs_readdata_free() can now become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
(cherry picked from 5e1ce40f0c3c8f67591aff17756930d7a18ceb1a commit)
Remove uevent dock notifications. There are no consumers
of these events at present, and uevents are likely not the
correct way to send this type of event anyway.
Until I get some kind of idea if anyone in userspace cares
about dock events, I will just not send any.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unhide the SMBus controller on the Asus PU-DLS board.
This fixes bug #6763.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
contig.c (FLATMEM) requires the same optimization as in discontig.c for show_mem
when VIRTUAL_MEM_MAP is in use. Otherwise FLATMEM has softlockup timeouts.
This was boot tested for memory configuration: SPARSEMEM,
DISCONTIG+VIRTUAL_MEM_MAP, FLATMEM, FLATMEM+VIRTUAL_MEM_MAP and
FLATMEM+VIRTUAL_MEM_MAP with largest memory gap less than LARGE_GAP by
using boot parameter "mem=".
This was boot tested and "echo m >/proc/sysrq-trigger" output evaluated for
: FLATMEM, FLATMEM+VIRTUAL_MEM_MAP, DISCONTIGMEM+VIRTUAL_MEM_MAP and
SPARSEMEM.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When an object is created via a symlink into an audited directory, audit misses
the event due to not having collected the inode data for the directory. Modify
__audit_inode_child() to copy the parent inode data if a parent wasn't found in
audit_names[].
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When the specified path is an existing file or when it is a symlink, audit
collects the wrong inode number, which causes it to miss the open() event.
Adding a second hook to the open() path fixes this.
Also add audit_copy_inode() to consolidate some code.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (24 commits)
Revert "[PATCH] USB: move usb_device_class class devices to be real devices"
Revert "[PATCH] USB: convert usb class devices to real devices"
USB: UHCI: Don't test the Short Packet Detect bit
USB: unusual_devs entry for Nokia 3250
USB: dummy-hcd: disable interrupts during req->complete
USB: fix the USB_GADGET_DUMMY_HCD dependencies
USB: ati_remote.c: autorepeat fix
USB: doc: fixes devio.c location in proc_usb_info.txt.
USB: doc: usb-help.txt update.
USB: Patch for rtl8150 to fix unplug problems
USB: cypress driver comment updates
USB: unusual_devs device removal
usb-storage: Add US_FL_IGNORE_DEVICE flag; ignore ZyXEL G220F
USB: New USB ID for Belkin Serial Adapter
USB: Additional PID for the ftdi_sio driver
USB: adding support for SHARP WS003SH to ipaq.c
USB: Fix Freescale high-speed USB host dependency
USB: Removed 3-port device handler from Option driver
USB: Drop Sierra Wireless MC8755 from the Option driver
USB: Let option driver handle Anydata CDMA modems. Remove anydata driver.
...
This reverts c182274ffe commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts bd00949647 commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new unusual_devs flag for when usb-storage needs to ignore
a device that it would otherwise claim.
We need to ignore the ZyXEL G220F as it is a virtual CDROM drive which
includes the windows driver for this USB-WLAN adapter. After the windows
driver is installed on a windows system, it converts it into a WLAN adapter
(by ejecting the virtual disc).
The virtual CDROM is of no interest to Linux users. The zd1211rw driver will
automatically perform the eject operation, we just need to ensure that
usb-storage does not claim the device.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix some sparse warnings on ia64. Large constants that should be long
instead of int. Use NULL instead of 0. Add some missing __iomem
casts. Replace a non-C99 structure assignment.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
include/linux/security.h: In function ‘security_release_secctx’:
include/linux/security.h:2757: warning: ‘return’ with a value, in function returning void
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Catherine Zhang <cxzhang@watson.ibm.com>
This patch implements a cleaner fix for the memory leak problem of the
original unix datagram getpeersec patch. Instead of creating a
security context each time a unix datagram is sent, we only create the
security context when the receiver requests it.
This new design requires modification of the current
unix_getsecpeer_dgram LSM hook and addition of two new hooks, namely,
secid_to_secctx and release_secctx. The former retrieves the security
context and the latter releases it. A hook is required for releasing
the security context because it is up to the security module to decide
how that's done. In the case of Selinux, it's a simple kfree
operation.
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_queue_head_init() function is used both in drivers for private use
and in the core networking code. The usage models are vastly set of
functions that is only softirq safe; while the driver usage tends to be
more limited to a few hardirq safe accessor functions. Rather than
annotating all 133+ driver usages, for now just split this lock into a per
queue class. This change is obviously safe and probably should make
2.6.18.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dev_alloc_skb variant that takes a struct net_device * paramater.
For now that paramater is unused, but I'll use it to allocate the skb
from node-local memory in a follow-up patch. Also there have been some
other plans mentioned on the list that can use it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses notifier blocks to implement a network event
notifier mechanism.
Clients register their callback function by calling
register_netevent_notifier() like this:
static struct notifier_block nb = {
.notifier_call = my_callback_func
};
...
register_netevent_notifier(&nb);
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refer to RFC2012, tcpAttemptFails is defined as following:
tcpAttemptFails OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times TCP connections have made a direct
transition to the CLOSED state from either the SYN-SENT
state or the SYN-RCVD state, plus the number of times TCP
connections have made a direct transition to the LISTEN
state from the SYN-RCVD state."
::= { tcp 7 }
When I lookup into RFC793, I found that the state change should occured
under following condition:
1. SYN-SENT -> CLOSED
a) Received ACK,RST segment when SYN-SENT state.
2. SYN-RCVD -> CLOSED
b) Received SYN segment when SYN-RCVD state(came from LISTEN).
c) Received RST segment when SYN-RCVD state(came from SYN-SENT).
d) Received SYN segment when SYN-RCVD state(came from SYN-SENT).
3. SYN-RCVD -> LISTEN
e) Received RST segment when SYN-RCVD state(came from LISTEN).
In my test, those direct state transition can not be counted to
tcpAttemptFails.
Signed-off-by: Wei Yongjun <yjwei@nanjing-fnst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Header doesn't use anything from atomic.h.
It fixes headers_check warning:
include/linux/netfilter_bridge.h requires asm/atomic.h, which does not exist
Compile tested on
alpha arm i386-up sparc sparc64-up x86_64
alpha-up i386 sparc64 sparc-up x86_64-up
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current users of ip6_dst_lookup can be divided into two classes:
1) The caller holds no locks and is in user-context (UDP).
2) The caller does not want to lookup the dst cache at all.
The second class covers everyone except UDP because most people do
the cache lookup directly before calling ip6_dst_lookup. This patch
adds ip6_sk_dst_lookup for the first class.
Similarly ip6_dst_store users can be divded into those that need to
take the socket dst lock and those that don't. This patch adds
__ip6_dst_store for those (everyone except UDP/datagram) that don't
need an extra lock.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (26 commits)
V4L/DVB (4380): Bttv: Revert VBI_OFFSET to previous value, it works better
V4L/DVB (4379): Videodev: Check return value of class_device_register() correctly
V4L/DVB (4373): Correctly handle sysfs error leg file removal in pvrusb2
V4L/DVB (4368): Bttv: use class_device_create_file and handle errors
V4L/DVB (4367): Videodev: Handle class_device related errors
V4L/DVB (4365): OVERLAY flag were enabled by mistake
V4L/DVB (4344): Fix broken dependencies on media Kconfig
V4L/DVB (4343): Fix for compilation without V4L1 or V4L1_COMPAT
V4L/DVB (4342): Fix ext_controls align on 64 bit architectures
V4L/DVB (4341): VIDIOCSMICROCODE were missing on compat_ioctl32
V4L/DVB (4322): Fix dvb-pll autoprobing
V4L/DVB (4311): Fix possible dvb-pll oops
V4L/DVB (4337): Refine dead code elimination in pvrusb2
V4L/DVB (4323): [budget/budget-av/budget-ci/budget-patch drivers] fixed DMA start/stop code
V4L/DVB (4316): Check __must_check warnings
V4L/DVB (4314): Set the Auxiliary Byte when tuning LG H06xF in analog mode
V4L/DVB (4313): Bugfix for keycode calculation on NPG remotes
V4L/DVB (4310): Saa7134: rename dmasound_{init, exit}
V4L/DVB (4306): Support non interlaced capture by default for saa713x
V4L/DVB (4298): Check all __must_check warnings in bttv.
...
Patch from Tony Lindgren
"clocks" is only needed only for CONFIG_OMAP_RESET_CLOCKS,
which turns of all unused clocks in with late_initcall. This is to kill
clocks that may have been left on by the bootloader. Having static and
non-static declaration of clocks makes omap_h2_1610_defconfig build fail.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our pseries hcall interfaces are out of control:
plpar_hcall_norets
plpar_hcall
plpar_hcall_8arg_2ret
plpar_hcall_4out
plpar_hcall_7arg_7ret
plpar_hcall_9arg_9ret
Create 3 interfaces to cover all cases:
plpar_hcall_norets: 7 arguments no returns
plpar_hcall: 6 arguments 4 returns
plpar_hcall9: 9 arguments 9 returns
There are only 2 cases in the kernel that need plpar_hcall9, hopefully
we can keep it that way.
Pass in a buffer to stash return parameters so we avoid the &dummy1,
&dummy2 madness.
Signed-off-by: Anton Blanchard <anton@samba.org>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes several problems:
- The legacy backlight value might be set at interrupt time. Introduced
a worker to prevent it from directly calling the backlight code.
- via-pmu allows the backlight to be grabbed, in which case we need to
prevent other kernel code from changing the brightness.
- Don't send PMU requests in via-pmu-backlight when the machine is about
to sleep or waking up.
- More Kconfig fixes.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The backlight and lcd subsystems can be notified by the framebuffer layer
of blanking events. However, these subsystems, as a whole, can function
independently from the framebuffer layer. But in order to enable to the
lcd and backlight subsystems, the framebuffer has to be compiled also,
effectively sucking in a huge amount of unneeded code.
To prevent dependency problems, separate out the framebuffer notification
mechanism from the framebuffer layer and permanently link it to the kernel.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is currently no affected user in the tree, but usage is less
surprising that way.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kprobe inserts breakpoint instruction in probepoint and then jumps to
instruction slot when breakpoint is hit, the instruction slot icache must
be consistent with dcache. Here is the patch which invalidates instruction
slot icache area.
Without this patch, in some machines there will be fault when executing
instruction slot where icache content is inconsistent with dcache.
Signed-off-by: bibo,mao <bibo.mao@intel.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Acked-by: Keshavamurthy Anil S <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable delay accounting by default so that feature gets coverage testing
without requiring special measures.
Earlier, it was off by default and had to be enabled via a boot time param.
This patch reverses the default behaviour to improve coverage testing. It
can be removed late in the kernel development cycle if its believed users
shouldn't have to incur any cost if they don't want delay accounting. Or
it can be retained forever if the utility of the stats is deemed common
enough to warrant keeping the feature on.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Complete the separation of delay accounting and taskstats by ignoring the
return value of delay accounting functions that fill in parts of taskstats
before it is sent out (either in response to a command or as part of a task
exit).
Also make delayacct_add_tsk return silently when delay accounting is turned
off rather than treat it as an error.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IRQs need refcounting and a state flag to track whether the the IRQ should
be enabled or disabled as a "normal IRQ" source after a series of calls to
{en,dis}able_irq(). For shared IRQs, the IRQ must be enabled so long as at
least one driver needs it active.
Likewise, IRQs need the same support to track whether the IRQ should be
enabled or disabled as a "wakeup event" source after a series of calls to
{en,dis}able_irq_wake(). For shared IRQs, the IRQ must be enabled as a
wakeup source during sleep so long as at least one driver needs it. But
right now they _don't have_ that refcounting ... which means sharing a
wakeup-capable IRQ can't work correctly in some configurations.
This patch adds the refcount and flag mechanisms to set_irq_wake() -- which
is what {en,dis}able_irq_wake() call -- and minimal documentation of what
the irq wake mechanism does.
Drivers relying on the older (broken) "toggle" semantics will trigger a
warning; that'll be a handful of drivers on ARM systems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Events sent by Process Events Connector from a 64-bit kernel are not binary
compatible with a 32-bit userspace program because the "timestamp" field
(struct timespec) is not arch independent. This affects the fields that
follow "timestamp" as they will be be off by 8 bytes.
This is a problem for 32-bit userspace programs running with 64-bit kernels
on ppc64, s390, x86-64.. any "biarch" system.
Matt had submitted a different solution to lkml as an RFC earlier. We have
since switched to a solution recommended by Evgeniy Polyakov.
This patch fixes the problem by changing the timestamp to be a __u64, which
stores the number of nanoseconds.
Tested on a x86_64 system with both 32 bit application and 64 bit
application and on a i386 system.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Guillaume Thouvenin <guillaume.thouvenin@bull.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The inode number out of an NFS file handle gets passed eventually to
ext3_get_inode_block() without any checking. If ext3_get_inode_block()
allows it to trigger an error, then bad filehandles can have unpleasant
effect - ext3_error() will usually cause a forced read-only remount, or a
panic if `errors=panic' was used.
So remove the call to ext3_error there and put a matching check in
ext3/namei.c where inode numbers are read off storage.
[akpm@osdl.org: fix off-by-one error]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: <stable@kernel.org>
Cc: "Stephen C. Tweedie" <sct@redhat.com>
Cc: Eric Sandeen <esandeen@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
/proc/pal/*/version_info is a bit confusing. HP firmware, at least,
reports 07.31 instead of 0.7.31. Also, the comment is out of place;
it's an internal detail about the implementation of ia64_pal_version.
Since the 2.2 revision of the SDM still states that PAL_VERSION can
be called in virtual mode, correct the comment to be more accurate.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Move all the Hypervisor call definitions to to a single header file.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previous changes have treated the return values of get_property as
const, so now we can make the actual change to get_property(). There
shouldn't be a need to cast the return values anymore.
We will now get compiler warnings when property values are assigned to
a non-const variable.
If properties need to be updated, there's still the of_find_property
function.
Built for cell_defconfig, chrp32_defconfig, g5_defconfig,
iseries_defconfig, maple_defconfig, pmac32_defconfig, ppc64_defconfig
and pseries_defconfig.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
powermac platform & macintosh driver changes.
Built for pmac32_defconfig, g5_defconfig
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
cell platform changes.
Built for cell_defconfig
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
powerpc core changes.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3734/1: Fix the unused variable warning in __iounmap()
[ARM] 3737/1: Export ARM copy/clear_user_page symbols
[ARM] 3736/1: xscale: don't mis-report 80219 as an iop32x
[ARM] 3733/2: S3C24XX: Remove old IDE registers in Anubis
[ARM] 3732/1: S3C24XX: tidy syntax in osiris and anubis machines
[ARM] Fix SMP booting
[ARM] 3731/1: Allow IRQ definitions of IQ80331 and IQ80332 to co-exist
[ARM] 3730/1: ep93xx: enable usb ohci driver in the defconfig
[ARM] Fix cats build
It was broken before. But having it is important as possible hardware
bug workaround.
And previously there was no way to force swiotlb if there is another IOMMU.
Side effect is that iommu=force won't force swiotlb anymore even if there
isn't another IOMMU.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Calgary hits a NULL pointer dereference when booting in a multi-chassis
NUMA system. See Redhat bugzilla number 198498, found by Konrad
Rzeszutek (konradr@redhat.com).
There are many issues that had to be resolved to fix this problem.
Firstly when I originally wrote the code to handle NUMA systems, I
had a large misunderstanding that was not corrected until now. That was
that I thought the "number of nodes online" referred to number of
physical systems connected. So that if NUMA was disabled, there
would only be 1 node and it would only show that node's PCI bus.
In reality if NUMA is disabled, the system displays all of the
connected chassis as one node but is only ignorant of the delays
in accessing main memory. Therefore, references to num_online_nodes()
and MAX_NUMNODES are incorrect and need to be set to the maximum
number of nodes that can be accessed (which are 8). I created a
variable, MAX_NUM_CHASSIS, and set it to 8 to fix this.
Secondly, when walking the PCI in detect_calgary, the code only
checked the first "slot" when looking to see if a device is present.
This will work for most cases, but unfortunately it isn't always the
case. In the NUMA MXE drawers, there are USB devices present on the
3rd slot (with slot 1 being empty). So, to work around this, all
slots (up to 8) are scanned to see if there are any devices present.
Lastly, the bus is being enumerated on large systems in a different
way the we originally thought. This throws the ugly logic we had
out the window. To more elegantly handle this, I reorganized the
kva array to be sparse (which removed the need to have any bus number
to kva slot logic in tce.c) and created a secondary space array to
contain the bus number to phb mapping.
With these changes Calgary boots on an x460 with 4 nodes with and
without NUMA enabled.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed usage of HAVE_V4L1
Including videodev.h will just include videodev2.h if V4L1 is not supported
V4L1 code at core drivers will honor CONFIG_V4L1_COMPAT stuff
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
u64 is aligned as 128bits on x86_64 architetures, requiring an special
handling to ioctls that depends on v4l2_ext_control.
Let's fix this before ext controls go to kernel mainstream to avoid one
more compat32 stuff.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Check __must_check warnings for class_device_register and class_device_create_file
video_device_create_file was declared as a void, but instead should
return the int value of class_device_create_file.
Move the check from bttv-driver.c into v4l2-dev.h, because all other
callers of video_device_create_file must also be checked.
Replace the call to class_device_create_file in videodev.c with
video_device_create_file, as defined in v4l2-dev.h, so that the
return value of class_device_create_file will be checked.
Check the return value of class_device_register in videodev.c and
pvrusb2-sysfs.c
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix robust PI-futexes to be properly unlocked on unexpected exit.
For this to work the kernel has to know whether a futex is a PI or a
non-PI one, because the semantics are different. Since the space in
relevant glibc data structures is extremely scarce, the best solution is
to encode the 'PI' information in bit 0 of the robust list pointer.
Existing (non-PI) glibc robust futexes have this bit always zero, so the
ABI is kept. New glibc with PI-robust-futexes will set this bit.
Further fixes from Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In x86_64 platform, INT1 and INT3 trap stack is IST stack called DEBUG_STACK,
when INT1/INT3 trap happens, system will switch to DEBUG_STACK by hardware.
Current DEBUG_STACK size is 4K, when int1/int3 trap happens, kernel will
minus current DEBUG_STACK IST value by 4k. But if int3/int1 trap is nested,
it will destroy other vector's IST stack. This patch modifies this, it sets
DEBUG_STACK size as 8K and allows two level of nested int1/int3 trap.
Kprobe DEBUG_STACK may be nested, because kprobe handler may be probed
by other kprobes.
Thanks jbeulich for pointing out error in the first patch.
[AK: nested kprobes are pretty dubious. Hopefully one nest
will be enough. This will cost 8K per CPU (4K more than before)]
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We currently try to allocate a max_recv_data_segment_length
which can be very large (default is 64K), and common uses
are up to 1MB. It is very very difficult to allocte this
much contiguous memory and it turns out we never even use it.
We really only need a couple of pages, so this patch has us
allocates just what we know what we need today.
Later if vendors start adding vendor specific data and
we need to handle large buffers we can do this, but for
the last 4 years we have not seen anyone do this or request
it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When we enter recovery and flush the running commands
we cannot freee the connection before flushing the commands.
Some commands may have a reference to the connection
that needs to be released before. iscsi_stop was forcing
the term and suspend too early and was causing a oops
in iser, so this patch removes those callbacks all together
and allows the LLD to handle that detail.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Abort handler fixes.
If a connection is dropped and reconnected while an abort is
running then we should assume the recovery code will clean up
the abort. Not doing so causes a oops.
And if a command completes then we get the status for the abort, we do not
need to call into the LLD to cleanup the resources. Doing this causes
and oops in iser because it ends up freeing some resources twice.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The iscsi tcp code can pluck multiple rt2s from the tasks's r2tqueue
in the xmit code. This can result in the task being queued on the xmit queue
but gettting completed at the same time.
This patch fixes the above bug by making the fifo a list so
we always remove the entry on the list del.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some drives claim they support cache flushing, but get seriously
confused if you try. Add this option to be able to boot with
barriers enabled by default.
Signed-off-by: Jens Axboe <axboe@suse.de>
Something is wrong with the 3-multiply (vs. 4-multiply) optimized
version of _FP_MUL_MEAT_2_*(), so just use the slower version
which actually computes correct values.
Noticed by Rene Rebe
Signed-off-by: David S. Miller <davem@davemloft.net>
AGP keeps its own copy of the protection_map, upcoming DRM changes will
also require access to this map from modules.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Dave Jones <davej@redhat.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SCSI] esp: Fix build.
[SPARC]: Fix SA_STATIC_ALLOC value.
[SPARC64]: Explicitly print return PC when the kernel fault PC is bogus.
The patch below moves the cpu hotplugging higher up in the cpufreq
layering; this is needed to avoid recursive taking of the cpu hotplug
lock and to otherwise detangle the mess.
The new rules are:
1. you must do lock_cpu_hotplug() around the following functions:
__cpufreq_driver_target
__cpufreq_governor (for CPUFREQ_GOV_LIMITS operation only)
__cpufreq_set_policy
2. governer methods (.governer) must NOT take the lock_cpu_hotplug()
lock in any way; they are called with the lock taken already
3. if your governer spawns a thread that does things, like calling
__cpufreq_driver_target, your thread must honor rule #1.
4. the policy lock and other cpufreq internal locks nest within
the lock_cpu_hotplug() lock.
I'm not entirely happy about how the __cpufreq_governor rule ended up
(conditional locking rule depending on the argument) but basically all
callers pass this as a constant so it's not too horrible.
The patch also removes the cpufreq_governor() function since during the
locking audit it turned out to be entirely unused (so no need to fix it)
The patch works on my testbox, but it could use more testing
(otoh... it can't be much worse than the current code)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add bridge netfilter deferred output hooks to feature-removal-schedule
and disable them by default. Until their removal they will be
activated by the physdev match when needed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_alloc_skb is designated for RX descriptors, not TX. (Some drivers
use it for the latter anyway, but that's a different story)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
skbuff.h has an #ifndef CONFIG_HAVE_ARCH_DEV_ALLOC_SKB to allow
architectures to reimplement __dev_alloc_skb. It's not set on any
architecture and now that we have an architecture-overrideable
NET_SKB_PAD there is not point at all to have one either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Martin Michlmayr
ARCH_IQ80331 and MACH_IQ80332 can be enabled at the same time but a
header file makes certain IRQ definitions conditional, leading to
the following compilation error when both platforms are enabled:
arch/arm/mach-iop3xx/iq80332-pci.c: In function 'iq80332_map_irq':
arch/arm/mach-iop3xx/iq80332-pci.c:54: error: 'IRQ_IQ80332_INTA' undeclared (first use in this function)
arch/arm/mach-iop3xx/iq80332-pci.c:54: error: (Each undeclared identifier is reported only once
arch/arm/mach-iop3xx/iq80332-pci.c:54: error: for each function it appears in.)
arch/arm/mach-iop3xx/iq80332-pci.c:54: error: 'IRQ_IQ80332_INTB' undeclared (first use in this function)
arch/arm/mach-iop3xx/iq80332-pci.c:54: error: 'IRQ_IQ80332_INTC' undeclared (first use in this function)
arch/arm/mach-iop3xx/iq80332-pci.c:54: error: 'IRQ_IQ80332_INTD' undeclared (first use in this function)
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In PSCHED_TADD and PSCHED_TADD2, if delta is less than tv.tv_usec (so,
less than USEC_PER_SEC too) then tv_res will be smaller than tv. The
affectation "(tv_res).tv_usec = __delta;" is wrong. The fix is to
revert to the original code before
4ee303dfea and change the 'if' in
'while'.
[Shuya MAEDA: "while (__delta >= USEC_PER_SEC){ ... }" instead of
"while (__delta > USEC_PER_SEC){ ... }"]
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate MADs sent by userspace clients for spec compliance with
C13-18.1.1 (prevent duplicate requests and responses sent on the
same port). Without this, RMPP transactions get aborted because
of duplicate packets.
This patch is similar to that provided by Jack Morgenstein.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The CPU hotplug locking was quite messy, with a recursive lock to
handle the fact that both the actual up/down sequence wanted to
protect itself from being re-entered, but the callbacks that it
called also tended to want to protect themselves from CPU events.
This splits the lock into two (one to serialize the whole hotplug
sequence, the other to protect against the CPU present bitmaps
changing). The latter still allows recursive usage because some
subsystems (ondemand policy for cpufreq at least) had already gotten
too used to the lax locking, but the locking mistakes are hopefully
now less fundamental, and we now warn about recursive lock usage
when we see it, in the hope that it can be fixed.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[TIPC]: Removing useless casts
[IPV4]: Fix nexthop realm dumping for multipath routes
[DUMMY]: Avoid an oops when dummy_init_one() failed
[IFB] After ifb_init_one() failed, i is increased. Decrease
[NET]: Fix reversed error test in netif_tx_trylock
[MAINTAINERS]: Mark LAPB as Oprhan.
[NET]: Conversions from kmalloc+memset to k(z|c)alloc.
[NET]: sun happymeal, little pci cleanup
[IrDA]: Use alloc_skb() in IrDA TX path
[I/OAT]: Remove pci_module_init() from Intel I/OAT DMA engine
[I/OAT]: net/core/user_dma.c should #include <net/netdma.h>
[SCTP]: ADDIP: Don't use an address as source until it is ASCONF-ACKed
[SCTP]: Set chunk->data_accepted only if we are going to accept it.
[SCTP]: Verify all the paths to a peer via heartbeat before using them.
[SCTP]: Unhash the endpoint in sctp_endpoint_free().
[SCTP]: Check for NULL arg to sctp_bucket_destroy().
[PKT_SCHED] netem: Fix slab corruption with netem (2nd try)
[WAN]: Converted synclink drivers to use netif_carrier_*()
[WAN]: Cosmetic changes to N2 and C101 drivers
[WAN]: Added missing netif_dormant_off() to generic HDLC
...
A non-zero return value indicates success from spin_trylock,
not error.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every file should #include the headers containing the prototypes for
its global functions.
Especially in cases like this one where gcc can tell us through a
compile error that the prototype was wrong...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements Rules D1 and D4 of Sec 4.3 in the ADDIP draft.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements Path Initialization procedure as described in
Sec 2.36 of RFC4460.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabre and Psycho PCI controllers can have partial interrupt-map
properties, meaning that on-board devices don't match up to any
entries. Instead, they are fully specified from the beginning and
we should pass them directly to the IRQ translator as-is.
Also, fill in the necessary translator slots for the "graphics"
and "expansion UPA" interrupts on Sabre, Psycho, and SYSIO SBUS.
Increase PROMREG_MAX to 24, as seen on SUNW,ffb devices.
Finally, prevent accidentally writing past the end of the of_device
struct resource[] and irqs[] arrays. Spit out a log message when
we ignore some entries because there are too many of them.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (38 commits)
[SCSI] More buffer->request_buffer changes
[SCSI] mptfusion: bump version to 3.04.01
[SCSI] mptfusion: misc fix's
[SCSI] mptfusion: firmware download boot fix's
[SCSI] mptfusion: task abort fix's
[SCSI] mptfusion: sas nexus loss support
[SCSI] mptfusion: sas loginfo update
[SCSI] mptfusion: mptctl panic when loading
[SCSI] mptfusion: sas enclosures with smart drive
[SCSI] NCR_D700: misc fixes (section and argument ordering)
[SCSI] scsi_debug: must_check fixes
[SCSI] scsi_transport_sas: kill the use of channel
[SCSI] scsi_transport_sas: add expander backlink
[SCSI] hide EH backup data outside the scsi_cmnd
[SCSI] ibmvscsi: handle inactive SCSI target during probe
[SCSI] ibmvscsi: allocate lpevents for ibmvscsi on iseries
[SCSI] aic7[9x]xx: Remove last vestiges of reverse_scan
[SCSI] aha152x: stop poking at saved scsi_cmnd members
[SCSI] st.c: Improve sense output
[SCSI] lpfc 8.1.7: Change version number to 8.1.7
...
Update ata_eh_about_to_do() and ata_eh_done() to improve EH action and
EHI flag handling.
* There are two types of EHI flags - one which expires on successful
EH and the other which expires on a successful reset. Make this
distinction clear.
* Unlike other EH actions, reset actions are represented by two EH
action masks and a EHI modifier. Implement correct about_to_do/done
semantics for resets. That is, prior to reset, related EH info is
sucked in from ehi and cleared, and after reset is complete, related
EH info in ehc is cleared.
These changes improve consistency and remove unnecessary EH actions
caused by stale EH action masks and EHI flags.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add missing volatile to the get_clock / get_cycles inline assemblies
to avoid that consecutive calls get optimized away.
Signed-off-by: Andreas Krebbel <krebbel1@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[VLAN]: __vlan_hwaccel_rx can use the faster ether_compare_addr
[PKT_SCHED] HTB: initialize upper bound properly
[IPV4]: Clear skb cb on IP input
[NET]: Update frag_list in pskb_trim
set_wmb should not be used in the kernel because it just confuses the
code more and has no benefit. Since it is not currently used in the
kernel this patch removes it so that new code does not include it.
All archs define set_wmb(var, value) to do { var = value; wmb(); }
while(0) except ia64 and sparc which use a mb() instead. But this is
still moot since it is not used anyway.
Hasn't been tested on any archs but x86 and x86_64 (and only compiled
tested)
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On systems with a large number of cpus, with even a modest rate of tasks
exiting per cpu, the volume of taskstats data sent on thread exit can
overflow a userspace listener's buffers.
One approach to avoiding overflow is to allow listeners to get data for a
limited and specific set of cpus. By scaling the number of listeners
and/or the cpus they monitor, userspace can handle the statistical data
overload more gracefully.
In this patch, each listener registers to listen to a specific set of cpus
by specifying a cpumask. The interest is recorded per-cpu. When a task
exits on a cpu, its taskstats data is unicast to each listener interested
in that cpu.
Thanks to Andrew Morton for pointing out the various scalability and
general concerns of previous attempts and for suggesting this design.
[akpm@osdl.org: build fix]
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't send taskstats (per-pid or per-tgid) on thread exit when no one is
listening for such data.
Currently the taskstats interface allocates a structure, fills it in and
calls netlink to send out per-pid and per-tgid stats regardless of whether
a userspace listener for the data exists (netlink layer would check for
that and avoid the multicast).
As a result of this patch, the check for the no-listener case is performed
early, avoiding the redundant allocation and filling up of the taskstats
structures.
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Send per-tgid data only once during exit of a thread group instead of once
with each member thread exit.
Currently, when a thread exits, besides its per-tid data, the per-tgid data
of its thread group is also sent out, if its thread group is non-empty.
The per-tgid data sent consists of the sum of per-tid stats for all
*remaining* threads of the thread group.
This patch modifies this sending in two ways:
- the per-tgid data is sent only when the last thread of a thread group
exits. This cuts down heavily on the overhead of sending/receiving
per-tgid data, especially when other exploiters of the taskstats
interface aren't interested in per-tgid stats
- the semantics of the per-tgid data sent are changed. Instead of being
the sum of per-tid data for remaining threads, the value now sent is the
true total accumalated statistics for all threads that are/were part of
the thread group.
The patch also addresses a minor issue where failure of one accounting
subsystem to fill in the taskstats structure was causing the send of
taskstats to not be sent at all.
The patch has been tested for stability and run cerberus for over 4 hours
on an SMP.
[akpm@osdl.org: bugfixes]
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Export I/O delays seen by a task through /proc/<tgid>/stats for use in top
etc.
Note that delays for I/O done for swapping in pages (swapin I/O) is clubbed
together with all other I/O here (this is not the case in the netlink
interface where the swapin I/O is kept distinct)
[akpm@osdl.org: printk warning fix]
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Erich Focht <efocht@ess.nec.de>
Cc: Levent Serinol <lserinol@gmail.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create a "taskstats" interface based on generic netlink (NETLINK_GENERIC
family), for getting statistics of tasks and thread groups during their
lifetime and when they exit. The interface is intended for use by multiple
accounting packages though it is being created in the context of delay
accounting.
This patch creates the interface without populating the fields of the data
that is sent to the user in response to a command or upon the exit of a task.
Each accounting package interested in using taskstats has to provide an
additional patch to add its stats to the common structure.
[akpm@osdl.org: cleanups, Kconfig fix]
Signed-off-by: Shailabh Nagar <nagar@us.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Erich Focht <efocht@ess.nec.de>
Cc: Levent Serinol <lserinol@gmail.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the task-related schedstats functions callable by delay accounting even
if schedstats collection isn't turned on. This removes the dependency of
delay accounting on schedstats.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Erich Focht <efocht@ess.nec.de>
Cc: Levent Serinol <lserinol@gmail.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unlike earlier iterations of the delay accounting patches, now delays are only
collected for the actual I/O waits rather than try and cover the delays seen
in I/O submission paths.
Account separately for block I/O delays incurred as a result of swapin page
faults whose frequency can be affected by the task/process' rss limit. Hence
swapin delays can act as feedback for rss limit changes independent of I/O
priority changes.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Erich Focht <efocht@ess.nec.de>
Cc: Levent Serinol <lserinol@gmail.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initialization code related to collection of per-task "delay" statistics which
measure how long it had to wait for cpu, sync block io, swapping etc. The
collection of statistics and the interface are in other patches. This patch
sets up the data structures and allows the statistics collection to be
disabled through a kernel boot parameter.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Erich Focht <efocht@ess.nec.de>
Cc: Levent Serinol <lserinol@gmail.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add another list utility function to check for last element in a list.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add frame buffer driver for the 2700G LCD controller present on CompuLab
CM-X270 computer module.
[adaplas]
- Add more informative help text to Kconfig
- Make DEBUG a Kconfig option as FB_MBX_DEBUG
- Remove #include mbxdebug.c, this is frowned upon
- Remove redundant casts
- Arrange #include's alphabetically
- Trivial whitespace
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's way past time to bump it to 8. Everyone had been warned - for
months now.
RH kernels have had this for more than a year.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drops gpio_set_high, gpio_set_low from the nsc_gpio_ops vtable. While we
can't drop them from scx200_gpio (or can we?), we dont need them for new users
of the exported vtable; gpio_set(1), gpio_set(0) work fine.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no excuse for userspace abusing this kernel header -- the kernel's
headers are not intended to provide a library of helper routines for
userspace. Using <asm/io.h> from userspace is broken on most architectures
anyway. Just say 'no'.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This isn't suitable for userspace to see -- the kernel headers are not a
random library of stuff for userspace; they're only there to define the
kernel<->user ABI for system libraries and tools. Anything which _was_
abusing asm/atomic.h from userspace was probably broken anyway -- as it often
didn't even give atomic operation.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove asm/irq.h from the exported headers -- there was never any good reason
for it to have been listed.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the now-unneeded kthread_stop_sem().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Got a customer bug report (https://bugzilla.novell.com/190296) about kernel
symbols longer than 127 characters which end up in a string buffer that is
not NULL terminated, leading to garbage in /proc/kallsyms. Using strlcpy
prevents this from happening, even though such symbols still won't come out
right.
A better fix would be to not use a fixed-size buffer, but it's probably not
worth the trouble. (Modversion'ed symbols even have a length limit of 60.)
[bunk@stusta.de: build fix]
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__vunmap must not rely on area->nr_pages when picking the release methode
for area->pages. It may be too small when __vmalloc_area_node failed early
due to lacking memory. Instead, use a flag in vmstruct to differentiate.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ib_fmr_pool_map_phys gets the virtual address by pointer but never writes
there, and users (e.g. srp) seem to assume this and ignore the value
returned. This patch cleans up the API to get the VA by value, and updates
all users.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The device address contains unsigned character arrays, which contain raw GID
addresses. The GIDs may not be naturally aligned, so do not cast them to
structures or unions.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The inline function compare_ether_addr is faster than memcmp.
Also, don't need to drag in proc_fs.h, the only reference to proc_dir_entry
is a pointer so the declaration is needed here.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Acked-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we pass the address of an iommu_table_cb to HvCallXm_getTceTableParms,
we don't actually need the structure definition anywhere except in the
iseries iommu code, so move the struct in there.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (53 commits)
[MIPS] sparsemem: fix crash in show_mem
[MIPS] vr41xx: Update workpad setup function
[MIPS] vr41xx: Update e55 setup function
[MIPS] vr41xx: Removed old v2.4 VRC4173 driver
[MIPS] vr41xx: Move IRQ numbers to asm-mips/vr41xx/irq.h
[MIPS] MIPSsim: Build fix, rename sim_timer_setup -> plat_timer_setup.
[MIPS] Remove unused code.
[MIPS] IP22 Fix brown paper bag in RTC code.
[MIPS] Atlas, Malta, SEAD: Don't disable interrupts in mips_time_init().
[MIPS] Replace board_timer_setup function pointer by plat_timer_setup.
[MIPS] Nuke redeclarations of board_time_init.
[MIPS] Remove redeclarations of setup_irq().
[MIPS] Nuke redeclarations of board_timer_setup.
[MIPS] Print out TLB handler assembly for debugging.
[MIPS] SMTC: Reformat to Linux style.
[MIPS] MIPSsim: Delete redeclaration of ll_local_timer_interrupt.
[MIPS] IP27: Reformatting.
[MIPS] IP27: Invoke setup_irq for timer interrupt so proc stats will be shown.
[MIPS] IP27: irq_chip startup method returns unsigned int.
[MIPS] IP27: struct irq_desc member handler was renamed to chip.
...
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] arch/arm/kernel/bios32.c: no need to set isa_bridge
[ARM] 3729/3: EABI padding rules necessitate the packed attribute of floatx80
[ARM] 3725/1: sharpsl_pm: warn about wrong temperature
[ARM] 3723/1: collie charging
[ARM] 3728/1: Restore missing CPU Hotplug irq helper
[ARM] 3727/1: fix ucb initialization on collie
[ARM] Allow Versatile to be built for AB and PB
[ARM] 3726/1: update {ep93xx,ixp2000,ixp23xx,lpd270,onearm} defconfigs to 2.6.18-rc1
[ARM] 3721/1: Small cleanup for locomo.c
1. MIPS should select SPARSEMEM_STATIC since allocating bootmem in
memory_present() will corrupt bootmap area.
2. pfn_valid() for SPARSEMEM is defined in linux/mmzone.h
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As a result of 894673ee61, the ARM
architecture is more or less unbuildable - only one defconfig appears
to build, with all others erroring out with:
CC arch/arm/kernel/setup.o
In file included from /home/rmk/git/linux-2.6-rmk/arch/arm/kernel/setup.c:22:
/home/rmk/git/linux-2.6-rmk/include/linux/root_dev.h:7: warning: implicit declaration of function `MKDEV'
...
Essentially, root_dev.h uses MKDEV and dev_t, but does not include any
headers which provide either of these definitions. The reason it worked
previously is that linux/tty.h just happened to include the required
headers for linux/root_dev.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Keep the result holder variable the same type as the quantity we are
retreiving in the get_user() macro - don't go through a pointer version
of the user space address type.
Using the address type causes problems if the address type was const
(newer versions of gcc quite rightly error out for that condition).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
include/asm-i386/system.h has trailing semicolons in some of the
macros that cause legitimate code to fail compilation, so remove
them. Also remove extra blank lines within one group of macros.
And put stts() and clts() back together; they got separated somehow.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This driver uses the hvc_console.c infrastructure that is used by the
pSeries virtual and RTAS consoles. This will allow us to make viocons.c
obsolete and is another step along the way to a combined kernel (as
viocons could not coexist with CONFIG_VT).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
A minor typo in the include/asm-sparc64/Kbuild file prevents the make
headers_install from building a useful tree of kernel headers for
sparc64.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Tom "spot" Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ItLpNaca into platforms/iseries now that it's not used elsewhere.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
HvLpConfig_get(Primary)LpIndex are currently static inlines that return
fields from the itLpNaca, if we make them real functions we can make the
itLpNaca private to iSeries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
No one outside platforms/iseries needs ItExtVpdPanel anymore, so move
it in there. It used to be needed by lparcfg, and so was exported, but
isn't needed anymore, so unexport it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
The ASCII -> EBCDIC functions, e2a() and strne2a() are now only used in
dt.c, so move them in there.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
* HEAD:
[NET]: fix __sk_stream_mem_reclaim
[Bluetooth] Fix deadlock in the L2CAP layer
[Bluetooth] Let BT_HIDP depend on INPUT
[Bluetooth] Avoid NULL pointer dereference with tty->driver
[Bluetooth] Remaining transitions to use kzalloc()
[WAN]: converting generic HDLC to use netif_dormant*()
[IPV4]: Fix error handling for fib_insert_node call
[NETROM] lockdep: fix false positive
[ROSE] lockdep: fix false positive
[AX.25]: Optimize AX.25 socket list lock
[IPCOMP]: Fix truesize after decompression
[IPV6]: Use ipv6_addr_src_scope for link address sorting.
[TCP] tcp_highspeed: Fix AI updates.
[MAINTAINERS]: Add proper entry for TC classifier
[NETROM]: Drop lock before calling nr_destroy_socket
[NETROM]: Fix locking order when establishing a NETROM circuit.
[AX.25]: Fix locking of ax25 protocol function list.
[IPV6]: order addresses by scope
* HEAD:
[PATCH] hwmon: Documentation update for abituguru
[PATCH] hwmon: Fix for first generation Abit uGuru chips
[PATCH] hwmon: New maintainer for w83791d
[PATCH] pca9539: Honor the force parameter
[PATCH] i2c-algo-bit: Wipe out dead code
[PATCH] i2c: Handle i2c_add_adapter failure in i2c algorithm drivers
[PATCH] i2c: New mailing list
[PATCH] i2c-ite: Plan for removal
[PATCH] i2c-powermac: Fix master_xfer return value
[PATCH] scx200_acb: Fix the block transactions
[PATCH] scx200_acb: Fix the state machine
[PATCH] i2c-iop3xx: Avoid addressing self
[PATCH] i2c: Fix 'ignore' module parameter handling in i2c-core
Implement the scheduled unexport of insert_resource.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the deprecated and no longer used pm_unregister_all().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When changing power states from D0->DX and then from DX->D0, some
Intel PCIE chipsets will cause a device reset to occur. This will
cause problems for any D State other than D3, since any state
information that the driver will expect to be present coming from
a D1 or D2 state will have been cleared. This patch addes a
flag to the pci_dev structure to indicate that devices should
not use states D1 or D2, and will set that flag for the affected
chipsets. This patch also modifies pci_set_power_state() so that
when a device driver tries to set the power state on
a device that is downstream from an affected chipset, or on one
of the affected devices it only allows state changes to or
from D0 & D3. In addition, this patch allows the delay time
between D3->D0 to be changed via a quirk. These chipsets also
need additional time to change states beyond the normal 10ms.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new defines of PCI-Express AER registers and their bits into file
include/linux/pci_regs.h.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB serial outside of the kernel tree can not build properly due to
usb-serial.h being buried down in the source tree. This patch moves the
location of the file to include/linux/usb and fixes up all of the usb
serial drivers to handle the move properly.
Cc: Sergei Organov <osv@javad.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent section changes broke gadget builds on some platforms. This patch
is the best fix that's available until better section markings exist:
- There's a lot of cleanup code that gets used in both init and exit paths;
stop marking it as "__exit".
(Best fix for this would be an "__init_or_exit" section marking, putting
the cleanup in __init when __exit sections get discarded else in __exit.)
- Stop marking the use-once probe routines as "__init" since references
to those routines are not allowed from driver structures. They're now
marked "__devinit", which in practice is a net lose.
(Best fix for this is likely to separate such use-once probe routines
from the driver structure ... but in general, all busses that aren't
hotpluggable will be forced to waste memory for all probe-only code.)
In general these broken section rules waste an average of two to four kBytes
per driver of code bloat ... because none of the relevant code can ever be
reused after module initialization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a US_FL_MAX_SECTORS_64 and removes the Genesys special-cases
for this that were in scsiglue.c. It also adds the flag to other devices
reported to need it.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds basic Wireless USB 1.0 definitions to usb_ch9.h that
fit into the existing set of declarations. Boils down to two new
recipients for requests (ports and remote pipes), rpipe reset and
abort request codes and wire adapter and remote pipe descriptor
types.
Wire adapters are the USB <-> Wireless USB adaptors; remote pipes
are used by those adapters to pipe the host <-> endpoint traffic.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Warning(/var/linsrc/linux-2617-g4//include/linux/usb.h:66): No description found for parameter 'ep_dev'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the value returned by the i2c-powermac's master_xfer method.
It should return the number of messages processed successfully, but
instead returns the number of data bytes in the first (and only)
processed message.
Also explicitly mention the master_xfer convention so that future
implementations get it right directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts generic HDLC (and WAN drivers using it) from
hdlc_set_carrier() to netif_dormant*() interface.
WAN hardware drivers should now use netif_carrier_on|off() like
other network drivers.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the recent discussion of taking 'volatile' off of the spinlock, I
noticed that while most arches #define cpu_relax() such that it implies
barrier(), some arches define cpu_relax() to be empty.
This patch changes the definition of cpu_relax() for frv, h8300, m68knommu,
sh, sh64, v850 and xtensa from an empty while(0) to the compiler barrier().
Signed-off-by: Chase Venters <chase.venters@clientec.com>
Acked-by: Arjan van de Ven <arjan@Linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixed 'section mismatch' errors in ALSA PCI drivers:
- removed invalid __devinitdata from pci id tables
- fix/remove __devinit of functions called in suspend/resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Drop the snd_minor structure's name field that was just a helper for
devfs device deregistration.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
1. Multipath devices for which SetPGID is not supported are not handled well.
Use NOP ccws for path verification (sans path grouping) when SetPGID is not
supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
first one) and try to find a common one. Moan if no common PGID can be
found (and use NOP verification). If no PGIDs have been set, use the css
global PGID (as before). (Rationale: SetPGID will get a command reject if
the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
will remove the old PGIDs. rcp will generate solicited CRWs which can be
savely ignored by the machine check handler (all other actions create
unsolicited CRWs).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
futex_atomic_cmpxchg_inatomic has the same bug as the other
atomic futex operations: the operation needs to be done in the
user address space, not the kernel address space. Add the missing
sacf 256 & sacf 0.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure that raw_local_save_flags and raw_local_irq_restore always get an
unsigned long parameter. raw_irqs_disabled should call raw_local_save_flags
instead of local_save_flags.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
__builtin_trap() has the archictecture defined backend in gcc since gcc 3.3.
To make sure the kernel builds with gcc 3.2 as well, use the old style BUG()
statement if compiled with older gcc versions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds the ability to add a backlink to a particular port. The
idea is to represent properly ports on expanders that are used
specifically for linking to the parent device in the topology.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a configuration was chosen to support both the Versatile
AB and PB boards, the result would write to registers not
available on the PB version of the board. Resolve this by
using machine_is_xxx().
Also, for the CLCD, despite how the code looks, both the AB
and PB access the same location to control the clock rate -
it's just called something different between the two board
versions. Invent our own name for this location and use it
unconditionally.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: ACPI_DOCK: Initialize the atomic notifier list
ACPI: acpi_os_allocate() fixes
ACPI: SBS: fix initialization, sem2mutex
ACPI: add 'const' to several ACPI file_operations
ACPI: delete some defaults from ACPI Kconfig
ACPI: "Device `[%s]' is not power manageable" make message debug only
ACPI: ACPI_DOCK Kconfig
Revert "Revert "ACPI: dock driver""
ACPI: acpi_os_get_thread_id() returns current
ACPI: ACPICA 20060707
Add an nfs4 operations count array to nfsd_stats structure. The count is
incremented in nfsd4_proc_compound() where all the operations are handled
by the nfsv4 server. This count of individual nfsv4 operations is also
entered into /proc filesystem.
Signed-off-by: Shankar Anand<shanand@novell.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
allyesconfig vmlinux size delta:
text data bss dec filename
20736884 6073834 3075176 29885894 vmlinux.before
20721009 6073966 3075176 29870151 vmlinux.after
~18 bytes per callsite, 15K of text size (~0.1%) saved.
(as an added bonus this also removes a lockdep annotation.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle memory-mapped chips properly, needed for example on DECstations.
This support was in Linux 2.4 but for some reason got lost in 2.6. This
patch is taken directly from the linux-mips repository.
[akpm@osdl.org: cleanup]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: Paul Gortmaker <penguin@muskoka.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Newer ARMs have a 40 bit physical address space, but mapping physical
memory above 4G needs a special page table format which we (currently?) do
not use for userspace mappings, so what happens instead is that mapping an
address >= 4G will happily discard the upper bits and wrap.
There is a valid_mmap_phys_addr_range() arch hook where we could check for
>= 4G addresses and deny the mapping, but this hook takes an unsigned long
address:
static inline int valid_mmap_phys_addr_range(unsigned long addr, size_t size);
And drivers/char/mem.c:mmap_mem() calls it like this:
static int mmap_mem(struct file * file, struct vm_area_struct * vma)
{
size_t size = vma->vm_end - vma->vm_start;
if (!valid_mmap_phys_addr_range(vma->vm_pgoff << PAGE_SHIFT, size))
So that's not much help either.
This patch makes the hook take a pfn instead of a phys address.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce the use of asm-offsets into the FRV architecture.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add coredump capability for the ELF-FDPIC binfmt.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the roundup() macro from binfmt_elf.c into linux/kernel.h as it's
generally useful.
[akpm@osdl.org: nuke all the other implementations]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add definitions for SEEK_SET, SEEK_CUR and SEEK_END to the kernel header
files.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some FRV arch compile errors, including:
(*) Marking nr_kernel_pages as __meminitdata so that references to it end up
being properly calculated rather than being assumed to be in the small
data section (and thus calculated wrt the GP register). Not doing this
causes the linker to emit errors as the offset is too big to fit into the
load instruction.
(*) Move pm_power_off into an unconditionally compiled .c file as it's now
unconditionally accessed.
(*) Declare frv_change_cmode() in a header file rather than in a .c file, and
declare it asmlinkage.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes several problems:
- pmac_backlight_key() is called under interrupt context, and therefore
can't use mutexes or semaphores, so defer the backlight level for
later, as it's not critical (original code by Aristeu S. Rozanski F.
<aris@valeta.org>).
- Add exports for functions that might be called from modules
- Fix Kconfig depdencies on PMAC_BACKLIGHT.
- Fix locking issues on calls from inside the driver (reported by
Aristeu S. Rozanski F., too)
- Fix wrong calculation of backlight values in some of the drivers
- Replace pmac_backlight_key_up/down by inline functions
[akpm@osdl.org: fix function prototypes]
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: Aristeu S. Rozanski F. <aris@valeta.org>
Acked-by: Rene Nussbaumer <linux-kernel@killerfox.forkbomb.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch slightly reworks the new irq code to fix a small design error. I
removed the passing of the trigger to the map() calls entirely, it was not a
good idea to have one call do two different things. It also fixes a couple of
corner cases.
Mapping a linux virtual irq to a physical irq now does only that. Setting the
trigger is a different action which has a different call.
The main changes are:
- I no longer call host->ops->map() for an already mapped irq, I just return
the virtual number that was already mapped. It was called before to give an
opportunity to change the trigger, but that was causing issues as that could
happen while the interrupt was in use by a device, and because of the
trigger change, map would potentially muck around with things in a racy way.
That was causing much burden on a given's controller implementation of
map() to get it right. This is much simpler now. map() is only called on
the initial mapping of an irq, meaning that you know that this irq is _not_
being used. You can initialize the hardware if you want (though you don't
have to).
- Controllers that can handle different type of triggers (level/edge/etc...)
now implement the standard irq_chip->set_type() call as defined by the
generic code. That means that you can use the standard set_irq_type() to
configure an irq line manually if you wish or (though I don't like that
interface), pass explicit trigger flags to request_irq() as defined by the
generic kernel interfaces. Also, using those interfaces guarantees that
your controller set_type callback is called with the descriptor lock held,
thus providing locking against activity on the same interrupt (including
mask/unmask/etc...) automatically. A result is that, for example, MPIC's
own map() implementation calls irq_set_type(NONE) to configure the hardware
to the default triggers.
- To allow the above, the irq_map array entry for the new mapped interrupt
is now set before map() callback is called for the controller.
- The irq_create_of_mapping() (also used by irq_of_parse_and_map()) function
for mapping interrupts from the device-tree now also call the separate
set_irq_type(), and only does so if there is a change in the trigger type.
- While I was at it, I changed pci_read_irq_line() (which is the helper I
would expect most archs to use in their pcibios_fixup() to get the PCI
interrupt routing from the device tree) to also handle a fallback when the
DT mapping fails consisting of reading the PCI_INTERRUPT_PIN to know wether
the device has an interrupt at all, and the the PCI_INTERRUPT_LINE to get an
interrupt number from the device. That number is then mapped using the
default controller, and the trigger is set to level low. That default
behaviour works for several platforms that don't have a proper interrupt
tree like Pegasos. If it doesn't work for your platform, then either
provide a proper interrupt tree from the firmware so that fallback isn't
needed, or don't call pci_read_irq_line()
- Add back a bit that got dropped by my main rework patch for properly
clearing pending IPIs on pSeries when using a kexec
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out that there is a way to build a kernel with NUMA and no SMP.
In that case we are missing one definition __inc_zone_state.
Provide that missing __inc_zone_state.
(akpm: NUMA && !SMP sounds odd, but I am told "But there is the concept of
cpuless nodes. A NUMA system without SMP has a single processor but multiple
memory nodes. This used to work before on IA64 (wasn't aware of it, never seen
anyone with this kind of thing).")
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.
However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count. This is wrong because curr_resync counts all sectors,
not just io sectors.
So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
screen_info.h doesn't have anything to do with the tty layer and shouldn't be
included by tty.h. This patches removes the include and modifies all users to
directly include screen_info.h. struct screen_info is mainly used to
communicate with the console drivers in drivers/video/console. Note that this
patch touches every arch and I have no way of testing it. If there is a
mistake the worst thing that will happen is a compile error.
[akpm@osdl.org: fix arm build]
[akpm@osdl.org: fix alpha build]
Signed-off-by: Jon Smirl <jonsmir@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MAX_NR_CONSOLES, fg_console, want_console and last_console are more of a
function of the VT layer than the TTY one. Moving these to vt.h and vt_kern.h
allows all of the framebuffer and VT console drivers to remove their
dependency on tty.h.
[akpm@osdl.org: fix alpha build]
Signed-off-by: Jon Smirl <jonsmir@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up lockdep on-stack-completion initializer. (This also removes the
dependency on waitqueue_lock_key.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
lockdep_map is embedded into every lock, which blows up data structure
sizes all around the kernel. Reduce the class-cache to be for the default
class only - that is used in 99.9% of the cases and even if we dont have a
class cached, the lookup in the class-hash is lockless.
This change reduces the per-lock dep_map overhead by 56 bytes on 64-bit
platforms and by 28 bytes on 32-bit platforms.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dopey bug. Causes hopelessly-wrong numbers from vmstat(8) and several other
counters.
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace acpi_in_resume with a more general hack
to check irqs_disabled() on any kmalloc() from ACPI.
While setting (system_state != SYSTEM_RUNNING) on resume
seemed more general, Andrew Morton preferred this approach.
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Make acpi_os_allocate() into an inline function to
allow /proc/slab_allocators to work.
Delete some memset() that could fault on allocation failure.
Signed-off-by: Len Brown <len.brown@intel.com>
Use thread info flags to track use of debug registers and IO bitmaps.
- add TIF_DEBUG to track when debug registers are active
- add TIF_IO_BITMAP to track when I/O bitmap is used
- modify __switch_to() to use the new TIF flags
Performance tested on Pentium II, ten runs of LMbench context switch
benchmark (smaller is better:)
before after
avg 3.65 3.39
min 3.55 3.33
Signed-off-by: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'blktrace' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] Only the first two bits in bio->bi_rw and rq->flags match
[PATCH] blktrace: readahead support
[PATCH] blktrace: fix barrier vs sync typo
The following patch gets rid of CONFIG_TSI108_BRIDGE. I add UPIO_TSI to
handle IIR and IER register in serial_in and serial_out.
(1) the reason to rewrite serial_in:
TSI108 rev Z1 version ERRATA. Reading the UART's Interrupt
Identification Register (IIR) clears the Transmit Holding Register
Empty (THRE) and Transmit buffer Empty (TEMP) interrupts even if they
are not enabled in the Interrupt Enable Register (IER). This leads to
loss of the interrupts. Interrupts are not cleared when reading UART
registers as 32-bit word.
(2) the reason to rewrite serial_out:
Check for UART_IER_UUE bit in the autoconfig routine. This section
of autoconfig is excluded for Tsi108/109 because bits 7 and 6 are
reserved for internal use. They are R/W bits. In addition to
incorrect identification, changing these bits (from 00) will make
Tsi108/109 UART non-functional.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux mutexes and the debug code that that reference
acpi_os_get_thread_id() are happy with 0.
But the AML mutexes in exmutex.c expect a unique non-zero
number for each thread - as they track this thread_id
to permit the mutex re-entrancy defined by the ACPI spec.
http://bugzilla.kernel.org/show_bug.cgi?id=6687
Signed-off-by: Len Brown <len.brown@intel.com>
Added the ACPI_PACKED_POINTERS_NOT_SUPPORTED macro to
support C compilers that do not allow the initialization
of address pointers within packed structures - even though
the hardware itself may support misaligned transfers. Some
of the debug data structures are packed by default to
minimize size.
Added an error message for the case where
acpi_os_get_thread_id() returns zero. A non-zero value is
required by the core ACPICA code to ensure the proper
operation of AML mutexes and recursive control methods.
The DSDT is now the only ACPI table that determines whether
the AML interpreter is in 32-bit or 64-bit mode. Not really
a functional change, but the hooks for per-table 32/64
switching have been removed from the code. A clarification
to the ACPI specification is forthcoming in ACPI 3.0B.
Fixed a possible leak of an Owner ID in the error
path of tbinstal.c acpi_tb_init_table_descriptor() and
migrated all table OwnerID deletion to a single place in
acpi_tb_uninstall_table() to correct possible leaks when using
the acpi_tb_delete_tables_by_type() interface (with assistance
from Lance Ortiz.)
Fixed a problem with Serialized control methods where the
semaphore associated with the method could be over-signaled
after multiple method invocations.
Fixed two issues with the locking of the internal
namespace data structure. Both the Unload() operator and
acpi_unload_table() interface now lock the namespace during
the namespace deletion associated with the table unload
(with assistance from Linn Crosetto.)
Fixed problem reports (Valery Podrezov) integrated: -
Eliminate unnecessary memory allocation for CreateXxxxField
http://bugzilla.kernel.org/show_bug.cgi?id=5426
Fixed problem reports (Fiodor Suietov) integrated: -
Incomplete cleanup branches in AcpiTbGetTableRsdt (BZ 369)
- On Address Space handler deletion, needless deactivation
call (BZ 374) - AcpiRemoveAddressSpaceHandler: validate
Device handle parameter (BZ 375) - Possible memory leak,
Notify sub-objects of Processor, Power, ThermalZone (BZ
376) - AcpiRemoveAddressSpaceHandler: validate Handler
parameter (BZ 378) - Minimum Length of RSDT should be
validated (BZ 379) - AcpiRemoveNotifyHandler: return
AE_NOT_EXIST if Processor Obj has no Handler (BZ (380)
- AcpiUnloadTable: return AE_NOT_EXIST if no table of
specified type loaded (BZ 381)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently struct scsi_cmnd has various fields that are used to backup
original data after the corresponding fields have been overridden for
EH commands. This means drivers can easily get at it and misuse it.
Due to the old_ naming this doesn't happen for most of them, but two
that have different names have been used wrong a lot (see previous
patch). Another downside is that they unessecarily bloat the scsi_cmnd
size.
This patch moves them onstack in scsi_send_eh_cmnd to fix those two
issues aswell as allowing future EH fixes like moving the EH command
submissions to use SG lists like everything else.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This reverts commit a5e1b94008.
Adrian Bunk points out that it has build errors, and apparently no
maintenance. Throw it out.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some SAS HBAs don't want to go to the trouble of tracking port numbers,
so they'd simply like to say "add this port and give it a number".
This is especially beneficial from the hotplug point of view, since
tracking ports and the available number space can be a real pain.
The current implementation uses an incrementing number per expander to
add the port on. However, since there can never be more ports than
there are phys, a later implementation will try to be more intelligent
about this.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use "+m" rather than a combination of "=m" and "m" for improved clarity
and consistency.
This also fixes some inlines that incorrectly didn't tell the compiler
that they read the old value at all, potentially causing the compiler to
generate bogus code. It appear that all of those potential bugs were
hidden by the use of extra "volatile" specifiers on the data structures
in question, though.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Certain subsystems in the stack (e.g., netfilter) can break the partial
checksum on GSO packets. Until they're fixed, this patch allows this to
work by recomputing the partial checksums through the GSO mechanism.
Once they've all been converted to update the partial checksum instead of
clearing it, this workaround can be removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the wrapper function skb_is_gso which can be used instead
of directly testing skb_shinfo(skb)->gso_size. This makes things a little
nicer and allows us to change the primary key for indicating whether an skb
is GSO (if we ever want to do that).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_bus callbacks map and get_flags can be constified, as they don't
alter the range or addr arguments. of_dump_addr and of_read_addr can
also be constified.
Built for 32- and 64-bit powerpc
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
