Add thermal zone and tmu node to support i.MX8MM thermal
driver, ONLY cpu thermal zone is supported, and cpu cooling
is also added.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add endpoint mode support for PCIe C5 controller in P2972-0000 platform
with information about supplies, PHY, PERST GPIO and GPIO that controls
PCIe reference clock coming from the host system.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding this alias for the Ethernet interface on Jetson TX1 allows the
bootloader to pass the MAC address to the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on Jetson TX1 platform because the
supply regulator is not specified for the backlight.
WARNING KERN lp855x 0-002c: 0-002c supply power not found, using dummy regulator
The backlight supply is provided by the 3.3V SYS rail and so add this
as the supply for the backlight.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on the Jetson TX2 platform ...
WARNING KERN tegra-sor 15540000.sor: 15540000.sor supply \
vdd-hdmi-dp-pll not found, using dummy regulator
The problem is caused because the regulator for the SOR device is
missing the '-supply' suffix in Device-Tree. Therefore, add the
'-supply' suffix to fix this warning.
Fixes: 3fdfaf8718 ("arm64: tegra: Enable DP support on Jetson TX2")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on Jetson TX1, Jetson Nano and Jetson
TX2 platforms because the supply regulators are not specified for the
EEPROMs.
WARNING KERN at24 0-0050: 0-0050 supply vcc not found, using dummy regulator
WARNING KERN at24 0-0057: 0-0057 supply vcc not found, using dummy regulator
For both of these platforms the EEPROM is powered by the main 1.8V
supply rail and so populate the supply for these devices to fix these
warnings.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit a5b6b67364 ("arm64: tegra: Add ID EEPROM for Jetson TX1
module") populated the EEPROM on the Jetson TX1 module, but did not
enable the corresponding I2C controller. Enable the I2C controller so
that this EEPROM can be accessed.
Fixes: a5b6b67364 ("arm64: tegra: Add ID EEPROM for Jetson TX1 module")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
clk_out_2 is a clock provided by the PMC, rather than the clock and
reset controller, as previously erroneously defined.
This patch changes clk_out_2 provider to PMC and uses corresponding
PMC clock ID for clk_out_2.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra132 and Tegra210 PMC blocks have clk_out_1, clk_out_2, clk_out_3,
and a blink clock as a part of the PMC.
These clocks were erroneously provided by the clock and reset controller
and are now provided by the PMC instead because that's where the primary
controls are.
Clock IDs for these clocks are defined in the PMC dt-bindings.
This patch updates the device tree to include the PMC dt-bindings header
and adds the #clock-cells property with one clock specifier to the PMC
node.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add usb-role-switch entry to peripheral USB port and add corresponding
connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has one XUSB device mode controller, which can be operated in
HS and SS modes. Add DT entry for XUSB device mode controller.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has one XUSB device mode controller, which can be operated in
HS and SS modes. Add DT entry for XUSB device mode controller.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add usb-role-switch entry to OTG USB port and add corresponding
connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate OTG vbus regulator and add usb-role-switch entry to USB 2-0
port and corresponding connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit enables XUSB host and pad controller in Tegra194
P2972-0000 board.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the kernel configuration option CONFIG_PCIE_DW_PLAT_HOST is enabled
then this can cause the kernel to incorrectly probe the generic
designware PCIe platform driver instead of the Tegra194 designware PCIe
driver. This causes a boot failure on Tegra194 because the necessary
configuration to access the hardware is not performed.
The order in which the compatible strings are populated in Device-Tree
is not relevant in this case, because the kernel will attempt to probe
the device as soon as a driver is loaded and if the generic designware
PCIe driver is loaded first, then this driver will be probed first.
Therefore, to fix this problem, remove the "snps,dw-pcie" string from
the compatible string as we never want this driver to be probe on
Tegra194.
Fixes: 2602c32f15 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HiHope RZ/G2M is advertised as compatible with panel idk-1110wr
from Advantech, however the panel isn't sold alongside the board.
A new dts, adding everything that's required to get the panel to
work with HiHope RZ/G2M, is the most convenient way to support the
HiHope RZ/G2M when it's connected to the idk-1110wr.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/1583957020-16359-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add initial support for the Renesas M3ULCB board equipped with an R-Car
M3-W+ SiP with 8 (2 x 4) GiB of RAM.
To avoid build error on 'ulcb.dtsi', ssi2 is added into 'r8a77961.dtsi'.
Based on commit 92980759c1 ("arm64: dts: renesas: Add support for
Salvator-XS with R-Car M3-W+").
Signed-off-by: Yuya Hamamachi <yuya.hamamachi.sx@renesas.com>
Link: https://lore.kernel.org/r/20200309064425.25437-3-yuya.hamamachi.sx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a device node for the Thermal Sensor/Chip Internal Voltage Monitor
in the R-Car M3-W+ (R8A77961) SoC, and describe the thermal zones.
According to the R-Car Gen3 Hardware Manual Errata for Revision 2.00 of
Jan 31, 2020, the thermal parameters for R-Car M3-W+ are the same as for
R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200306110025.24747-1-geert+renesas@glider.be
The LS1028A has six LPUART controllers. Add the nodes.
This was tested on a custom board.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200307091302.14881-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the redundant _mem suffix for SDHC reg names.
For SDcard instance, no need supply reg names since hc reg map
is accessed with index. So remove reg names for SDcard.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1583946863-24308-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enabling CQE support for eMMC by supplying the correct reg name
and flag which indicates CQE support.
Also remove the redundant _mem suffix for reg names.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1583946863-24308-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Register range of display clocks is 0x10000, as it can be seen from
DE2 documentation.
Fix it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Fixes: 2c796fc8f5 ("arm64: dts: allwinner: a64: add necessary device tree nodes for DE2 CCU")
[wens@csie.org: added fixes tag]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently, the EL0 SP alignment handler masks IRQs unnecessarily. It
does so due to historic code sharing of the EL0 SP and PC alignment
handlers, and branch predictor hardening applicable to the EL0 SP
handler.
We began masking IRQs in the EL0 SP alignment handler in commit:
5dfc6ed277 ("arm64: entry: Apply BP hardening for high-priority synchronous exception")
... as this shared code with the EL0 PC alignment handler, and branch
predictor hardening made it necessary to disable IRQs for early parts of
the EL0 PC alignment handler. It was not necessary to mask IRQs during
EL0 SP alignment exceptions, but it was not considered harmful to do so.
This masking was carried forward into C code in commit:
582f95835a ("arm64: entry: convert el0_sync to C")
... where the SP/PC cases were split into separate handlers, and the
masking duplicated.
Subsequently the EL0 PC alignment handler was refactored to perform
branch predictor hardening before unmasking IRQs, in commit:
bfe298745a ("arm64: entry-common: don't touch daif before bp-hardening")
... but the redundant masking of IRQs was not removed from the EL0 SP
alignment handler.
Let's do so now, and make it interruptible as with most other
synchronous exception handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
When building allnoconfig:
arch/arm64/kernel/cpu_errata.c:174:13: warning: unused function
'call_smc_arch_workaround_1' [-Wunused-function]
static void call_smc_arch_workaround_1(void)
^
1 warning generated.
Follow arch/arm and mark this function as __maybe_unused.
Fixes: 4db61fef16 ("arm64: kvm: Modernize __smccc_workaround_1_smc_start annotations")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Missing argument of another SYM_INNER_LABEL() breaks build for
CONFIG_FUNCTION_GRAPH_TRACER=y.
Fixes: e2d591d29d ("arm64: entry-ftrace.S: Convert to modern annotations for assembly functions")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Brown <broonie@kernel.org>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: amba: $nodename:0:
'amba' does not match
'^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
AMBA is a open standard for the connection and
management of functional blocks in a SoC.
It's compatible with 'simple-bus', so fix this error
by adding 'bus' to all Rockchip 'amba' nodes.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/simple-bus.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200302153047.17101-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
i.MX8MQ Phanbell board uses Realtek RTL8211FD as Ethernet PHY.
Its datasheet states that the proper post reset duration should be at least 50 ms.
Fixes: f34d4bfab3 ("arm64: dts: imx8mq-phanbell: Add support for ethernet")
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull in downstream patch from NXP repository to enable fspi device.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
crypto child nodes should use the "jr" name (without an index),
as indicated in the DT binding.
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
for example this error:
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: mmc@fe320000:
'clock-freq-min-max' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'clock-freq-min-max' is deprecated, so replace it by 'max-frequency'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
this error:
arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dt.yaml: mmc@fe320000:
'vqmmc' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'vqmmc' is not a valid property name for mmc nodes.
Fix this error by renaming it to 'vqmmc-supply'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
this error:
arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dt.yaml: mmc@ff0c0000:
'no-emmc' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'no-emmc' is not a valid property name for mmc nodes,
so remove it.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
An experimental test with the command below without
additional properties in 'rockchip-vop.yaml' gives this error:
arch/arm64/boot/dts/rockchip/px30-evb.dt.yaml: vop@ff470000:
'power-domains', 'rockchip,grf'
do not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/px30-evb.dt.yaml: vop@ff460000:
'power-domains', 'rockchip,grf'
do not match any of the regexes: 'pinctrl-[0-9]+'
'rockchip,grf' is not used by the Rockchip VOP driver,
so remove it from 'vop' nodes in 'px30.dtsi'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/
rockchip/rockchip-vop.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309081600.3887-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "spi-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine spi-rockchip.yaml and
spi-controller.yaml it gives this error:
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: spi@ff1d0000:
'max-freq' does not match any of the regexes:
'^.*@[0-9a-f]+$', '^slave$'
'max-freq' is not a valid property name for spi nodes,
so remove it.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309125145.14455-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each
connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected
on different buses, only one flash can be probed at a time.
Add fspi node properties aligned with LX2160A-RDB fspi properties.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update fspi node compatibles of LX2160A-RDB to "jedec,spi-nor" for
automatic detection of flash.
This also helps in fixing below warning:
spi-nor spi0.0: found mt35xu512aba, expected m25p80
spi-nor spi0.1: found mt35xu512aba, expected m25p80
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It was based on Google Source Code for Coral Edge TPU Mendel release:
https://coral.googlesource.com/linux-imx/
It was tested on Coral Dev Board using this command:
sudo stress --cpu 4 --timeout 3600
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the iommu-map property to the pci nodes so that the firmware
fixes it up with the required values thus enabling iommu for
devices connected over pci.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: /: compatible:
['rockchip,rk3399-evb', 'rockchip,rk3399', 'google,rk3399evb-rev2']
is not valid under any of the given schemas
'google,rk3399evb-rev2' was a no longer used variant for Google.
The binding only mentions 'rockchip,rk3399-evb', 'rockchip,rk3399',
so fix this error by removing 'google,rk3399evb-rev2' from
the compatible property in rk3399-evb.dts and change it into
generic rk3399-evb support only.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200302092759.3291-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The IMU chip on the librem5-devkit is not mounted at the "natural" place
that would match normal phone orientation (see the documentation for the
details about what that is).
Since the lsm9ds1 driver supports providing a mount matrix, we can describe
the orientation on the board in the dts:
Create a right-handed coordinate system (x * -1; see the datasheet for the
axis) and rotate 180 degrees around the y axis because the device sits on
the back side from the display.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The poly fuses can handle 6V 4Amps so incease the kernel limts to 5V
3.5Amps.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By adding broken-cd to the usdhc2 stanza the Redpine card can be
detected when the HKS is turned off and on.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify which regulator is used for cpufreq DVFS.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Connect the WoWWAN signal to a gpio key to wake up the system from suspend.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the simcom SIM7100 modem and the sai6 interface that connects it.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the sgtl5000 of the librem 5 devkit in devicetree.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Without a VBUS supply the dwc3 driver won't go into otg mode.
Fixes: eb4ea0857c ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds 4 eeprom support on i2c mux channel #0 -
1. Bootable 512Kbit eeprom at address 0x50.
2. Memory SO-DIMMs SPD channels at 0x51 (upper SO-DIMM) and 0x53.
3. 2Kb eeprom at 0x57 will be used by SolidRun to hold manufacturing
data.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the LTC3882 regulator so that the hardware monitoring
can be used with this device. This regulator provides the 0.78V
supply for the LX2160A.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "pinctrl" instead of "iomuxc"
for all i.MX8M SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit b9213899d2b0 ("arm64: dts: ls1028a: disable all enetc ports
by default") all the network ports are disabled by default. This makes
sense, but now we have to enable them explicitly in the boards. Do so
for the sl28 module.
Since we are at it. Make sure the second port is only enabled for the
variant 4 of the module. Variant 3 has only one network port.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Link the switch PHY nodes to the central MDIO controller PCIe endpoint
node on LS1028A (implemented as PF3) so that PHYs are accessible via
MDIO.
Enable SGMII AN on the Felix PCS by telling PHYLINK that the VSC8514
quad PHY is capable of in-band-status.
The PHYs are used in poll mode due to an issue with the interrupt line
on current revisions of the LS1028A-RDB board.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the switch device node, available on PF5, so that the switch port
sub-nodes (net devices) can be linked to corresponding board specific
phy nodes (external ports) or have their link mode defined (internal
ports).
The switch device features 6 ports, 4 with external links and 2
internally facing to the LS1028A SoC and connected via fixed links to 2
internal ENETC Ethernet controller ports.
Add the corresponding ENETC host port device nodes, mapped to PF2 and
PF6 PCIe functions. Since the switch only supports tagging on one CPU
port, only one port pair (swp4, eno2) is enabled by default and the
other, lower speed, port pair is disabled to prevent the PCI core from
probing them. If enabled, swp5 will be a fixed-link slave port.
DSA tagging can also be moved from the swp4-eno2 2.5G port pair to the
1G swp5-eno3 pair by changing the ethernet = <&enetc_port2> phandle to
<&enetc_port3> and moving it under port5, but in that case enetc_port2
should not be disabled, because it is the hardware owner of the Felix
PCS and disabling its memory would result in access faults in the Felix
DSA driver.
All ports are disabled by default, including the CPU port, and need to
be enabled on a per-board basis.
The phy-mode binding of the internal ENETC ports was modified from
"gmii" to "internal" to match the phy-mode of the internal-facing switch
ports connected to them. The ENETC driver does not perform any phy_mode
validation anyway, so the change is only cosmetic. Also, enetc_port2 is
defined as a fixed-link 1000 Mbps port even though it is 2500 Mbps (as
can be seen by the fact that it is connected to mscc_felix_port4). The
fact that it is currently defined as 1000 Mbps is an artifact of its
PHYLIB implementation instead of PHYLINK (the former can't describe a
fixed-link speed higher than what swphy can emulate from the Clause 22
MDIO spec).
The switch's INTB interrupt line signals:
- PTP TX timestamp availability
- TSN Frame Preemption
And don't forget to enable the 4MB BAR4 in the root complex ECAM space,
where the switch registers are mapped.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are few boards that enable all ENETC ports, so instead of having
board DTs disable them, do so in the DTSI and have the boards enable the
ports they use.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This specifier overrides the interrupt specifier with 3 cells from gic
(/interrupt-controller@6000000), but in fact ENETC is not an interrupt
controller, so the property is bogus.
Interrupts used by the children of the ENETC RCIE must use the full
3-cell specifier required by the GIC.
The issue has no functional consequence so there is no real reason to
port the patch to stable trees.
Fixes: 927d7f8575 ("arm64: dts: fsl: ls1028a: Add PCI IERC node and ENETC endpoints")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Unlike on arm32, the HAVE_ARM_ARCH_TIMER config symbol does not exist on
arm64.
Note that the toplevel ARM64 symbol always selects ARM_ARCH_TIMER, so
support for it is always included.
Fixes: 628d30d1cc ("arm64: Add platform selection for BCM2835.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We need the vt fixes in here and it resolves a merge issue with
drivers/tty/vt/selection.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sm8250 devicetree file for SM8250 SoC and SM8250 MTP platform.
This file adds the basic nodes like cpu, psci and other required
configuration for booting up to the serial console.
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200310050910.506854-1-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Disable Coresight funnel 4 and 5, for now, as these causes the MTP to
crash when clock late_initcall disables unused clocks.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200308055445.1992189-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
efi-entry.o is built on demand for efi-entry.stub.o, so you do not have
to repeat $(CONFIG_EFI) here. Adding it to 'targets' is enough.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Throwing our __uint128_t idioms at csum_ipv6_magic() makes it
about 1.3x-2x faster across a range of microarchitecture/compiler
combinations. Not much in absolute terms, but every little helps.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions. Use these for the compat VDSO,
allowing us to drop the custom ARM_ENTRY() and ARM_ENDPROC() macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions. Convert the assembly function in the
arm64 VDSO to the new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions.
The SDEI entry points are currently annotated as normal functions but
are called from non-kernel contexts with non-standard calling convention
and should therefore be annotated as such so do so.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: James Morse <james.Morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC with separate annotations for standard C callable functions,
data and code with different calling conventions.
Using these for __smccc_workaround_1_smc is more involved than for most
symbols as this symbol is annotated quite unusually, rather than just have
the explicit symbol we define _start and _end symbols which we then use to
compute the length. This does not play at all nicely with the new style
macros. Instead define a constant for the size of the function and use that
in both the C code and for .org based size checks in the assembly code.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
We have recently introduced new macros for annotating assembly symbols
for things that aren't C functions, SYM_CODE_START() and SYM_CODE_END(),
in an effort to clarify and simplify our annotations of assembly files.
Using these for __bp_harden_hyp_vecs is more involved than for most symbols
as this symbol is annotated quite unusually as rather than just have the
explicit symbol we define _start and _end symbols which we then use to
compute the length. This does not play at all nicely with the new style
macros. Since the size of the vectors is a known constant which won't vary
the simplest thing to do is simply to drop the separate _start and _end
symbols and just use a #define for the size.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC with separate annotations for standard C callable functions,
data and code with different calling conventions. Update the more
straightforward annotations in the kvm code to the new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These include specific
annotations for the start and end of data, update symbols for data to use
these.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions. Neither stext nor preserve_boot_args
is called with the usual AAPCS calling conventions and they should
therefore be annotated as code.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC and also add a new annotation for static functions which previously
had no ENTRY equivalent. Update the annotations in the core kernel code to
the new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions.
return_to_handler does entertaining things with LR so doesn't follow the
usual C conventions and should therefore be annotated as code rather than
a function.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions.
The patchable function entry versions of ftrace_*_caller don't follow the
usual AAPCS rules, pushing things onto the stack which they don't clean up,
and therefore should be annotated as code rather than functions.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC and also add a new annotation for static functions which previously
had no ENTRY equivalent. Update the annotations in the core kernel code to
the new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC with separate annotations for standard C callable functions,
data and code with different calling conventions. Update the
remaining annotations in the entry.S code to the new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions.
ret_from_fork is not a normal C function and should therefore be
annotated as code.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In an effort to clarify and simplify the annotation of assembly
functions new macros have been introduced. These replace ENTRY and
ENDPROC with two different annotations for normal functions and those
with unusual calling conventions. The vector table and handlers aren't
normal C style code so should be annotated as CODE.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that the rest of the code has been converted to the modern START/END
macros the AES_ENTRY() and AES_ENDPROC() macros look out of place and
like they need updating. Rename them to AES_FUNC_START() and AES_FUNC_END()
to line up with the modern style assembly macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
A couple of functions were missed in the modernisation of assembly macros,
update them too.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix typo in a comment in arch/arm64/include/asm/esr.h
"Unallocted" -> "Unallocated"
Signed-off-by: Chenggang Wang <wangchenggang@vivo.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch increases the reg addresses for QSPI boot and QSPI rootfs for
Stratix10 and Agilex to cater for the increased size of kernel Image.
Signed-off-by: Joyce Ooi <joyce.ooi@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Both, OrangePi One Plus and OrangePi Lite 2 have HDMI output. Enable it
in common DTSI.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
[patch split and commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Christopher Obbard <chris@64studio.com>
Tested-by: Christopher Obbard <chris@64studio.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
OrangePi One Plus has gigabit ethernet. Add nodes for it.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
[patch split and commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Christopher Obbard <chris@64studio.com>
Tested-by: Christopher Obbard <chris@64studio.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
It turns out that not all H6 boards have external 32kHz oscillator.
Currently the only one known such H6 board is Tanix TX6.
Move external oscillator node from common H6 dtsi to board specific dts
files where present.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Make zynqmp_firmware driver as optional to disable it, if user don't
want to use default zynqmp firmware interface.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We've been accruing these for a couple of weeks, so the batch is a bit
bigger than usual.
Largest delta is due to a led-bl driver that is added -- there was
a miscommunication before the merge window and the driver didn't make it
in. Due to this, the platforms needing it regressed. At this point, it
seemed easier to add the new driver than unwind the changes.
Besides that, there are a handful of various fixes:
- AMD tee memory leak fix
- A handful of fixlets for i.MX SCU communication
- A few maintainers woke up and realized DEBUG_FS had been missing for
a while, so a few updates of that.
... and the usual collection of smaller fixes to various platforms.
-----BEGIN PGP SIGNATURE-----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=gCNz
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"We've been accruing these for a couple of weeks, so the batch is a bit
bigger than usual.
Largest delta is due to a led-bl driver that is added -- there was a
miscommunication before the merge window and the driver didn't make it
in. Due to this, the platforms needing it regressed. At this point, it
seemed easier to add the new driver than unwind the changes.
Besides that, there are a handful of various fixes:
- AMD tee memory leak fix
- A handful of fixlets for i.MX SCU communication
- A few maintainers woke up and realized DEBUG_FS had been missing
for a while, so a few updates of that.
... and the usual collection of smaller fixes to various platforms"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (37 commits)
ARM: socfpga_defconfig: Add back DEBUG_FS
arm64: dts: socfpga: agilex: Fix gmac compatible
ARM: bcm2835_defconfig: Explicitly restore CONFIG_DEBUG_FS
arm64: dts: meson: fix gxm-khadas-vim2 wifi
arm64: dts: meson-sm1-sei610: add missing interrupt-names
ARM: meson: Drop unneeded select of COMMON_CLK
ARM: dts: bcm2711: Add pcie0 alias
ARM: dts: bcm283x: Add missing properties to the PWR LED
tee: amdtee: fix memory leak in amdtee_open_session()
ARM: OMAP2+: Fix compile if CONFIG_HAVE_ARM_SMCCC is not set
arm: dts: dra76x: Fix mmc3 max-frequency
ARM: dts: dra7: Add "dma-ranges" property to PCIe RC DT nodes
bus: ti-sysc: Fix 1-wire reset quirk
ARM: dts: r8a7779: Remove deprecated "renesas, rcar-sata" compatible value
soc: imx-scu: Align imx sc msg structs to 4
firmware: imx: Align imx_sc_msg_req_cpu_start to 4
firmware: imx: scu-pd: Align imx sc msg structs to 4
firmware: imx: misc: Align imx sc msg structs to 4
firmware: imx: scu: Ensure sequential TX
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
...
The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As specified in the smd-rpm-regulator binding and confirmed by the
pm8616 device specification, there is no vdd_l5. l5 vdd comes from
vdd_l4_l5_l6. Fix that (though it does not cause any issue since
the supply is not requested).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1583516368-29593-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- Fix misreporting of ASID limit when KPTI is enabled
- Fix busted NULL pointer checks for GICC structure in ACPI PMU code
- Avoid nobbling the "fsl_imx8_ddr" PMU counters when disabling them
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl5iMUgQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNMpPB/9OH2pp6QaosJKz6zHawyvG6K1RxCQC7TZw
PCXKWF1N9b1z/ZBq47goDC0rRxVzx+OAO9MY4DMLojWvv51GT/Z/LhrYkpXek48I
Dkfz8ZmhSyO54M8LDQQ79zKG4FzpLVsvVP2z9bMaq9Ut5BSNcKmjvY7h27/znk7N
fW0lRVBt3C7Cu5DTBqq3BN3AXEwoANb4QvqmmA6D/pZvl5MUXolulww6czknYyIE
VD7m7s6A3bPUWWVSWHuYxL9/N8fP7HbcBL09dEtIKI4n1O+mvvCx9uHxxokBGuSV
ENu7BWfm0LJ5JibbW/rSOT8u2tw4xY4njhXu06PnxWXQSF8RcaOV
=7zhy
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are another three arm64 fixes for 5.6, all pretty minor. Main
thing is fixing a silly bug in the fsl_imx8_ddr PMU driver where we
would zero the counters when disabling them.
- Fix misreporting of ASID limit when KPTI is enabled
- Fix busted NULL pointer checks for GICC structure in ACPI PMU code
- Avoid nobbling the "fsl_imx8_ddr" PMU counters when disabling them"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: context: Fix ASID limit in boot messages
drivers/perf: arm_pmu_acpi: Fix incorrect checking of gicc pointer
drivers/perf: fsl_imx8_ddr: Correct the CLEAR bit definition
The Frequency Invariance Engine (FIE) is providing a frequency
scaling correction factor that helps achieve more accurate
load-tracking.
So far, for arm and arm64 platforms, this scale factor has been
obtained based on the ratio between the current frequency and the
maximum supported frequency recorded by the cpufreq policy. The
setting of this scale factor is triggered from cpufreq drivers by
calling arch_set_freq_scale. The current frequency used in computation
is the frequency requested by a governor, but it may not be the
frequency that was implemented by the platform.
This correction factor can also be obtained using a core counter and a
constant counter to get information on the performance (frequency based
only) obtained in a period of time. This will more accurately reflect
the actual current frequency of the CPU, compared with the alternative
implementation that reflects the request of a performance level from
the OS.
Therefore, implement arch_scale_freq_tick to use activity monitors, if
present, for the computation of the frequency scale factor.
The use of AMU counters depends on:
- CONFIG_ARM64_AMU_EXTN - depents on the AMU extension being present
- CONFIG_CPU_FREQ - the current frequency obtained using counter
information is divided by the maximum frequency obtained from the
cpufreq policy.
While it is possible to have a combination of CPUs in the system with
and without support for activity monitors, the use of counters for
frequency invariance is only enabled for a CPU if all related CPUs
(CPUs in the same frequency domain) support and have enabled the core
and constant activity monitor counters. In this way, there is a clear
separation between the policies for which arch_set_freq_scale (cpufreq
based FIE) is used, and the policies for which arch_scale_freq_tick
(counter based FIE) is used to set the frequency scale factor. For
this purpose, a late_initcall_sync is registered to trigger validation
work for policies that will enable or disable the use of AMU counters
for frequency invariance. If CONFIG_CPU_FREQ is not defined, the use
of counters is enabled on all CPUs only if all possible CPUs correctly
support the necessary counters.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Access to the AMU counters should be disabled by default in kvm guests,
as information from the counters might reveal activity in other guests
or activity on the host.
Therefore, disable access to AMU registers from EL0 and EL1 in kvm
guests by:
- Hiding the presence of the extension in the feature register
(SYS_ID_AA64PFR0_EL1) on the VCPU.
- Disabling access to the AMU registers before switching to the guest.
- Trapping accesses and injecting an undefined instruction into the
guest.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The activity monitors extension is an optional extension introduced
by the ARMv8.4 CPU architecture. In order to access the activity
monitors counters safely, if desired, the kernel should detect the
presence of the extension through the feature register, and mediate
the access.
Therefore, disable direct accesses to activity monitors counters
from EL0 (userspace) and trap them to EL1 (kernel).
To be noted that the ARM64_AMU_EXTN kernel config does not have an
effect on this code. Given that the amuserenr_el0 resets to an
UNKNOWN value, setting the trap of EL0 accesses to EL1 is always
attempted for safety and security considerations. Therefore firmware
should still ensure accesses to AMU registers are not trapped in
EL2/EL3 as this code cannot be bypassed if the CPU implements the
Activity Monitors Unit.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The activity monitors extension is an optional extension introduced
by the ARMv8.4 CPU architecture. This implements basic support for
version 1 of the activity monitors architecture, AMUv1.
This support includes:
- Extension detection on each CPU (boot, secondary, hotplugged)
- Register interface for AMU aarch64 registers
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The default value of Kconfig for almost all sprd drivers are the same with
ARCH_SPRD, making these drivers built as modules as default would be easier
if we can set ARCH_SPRD as 'm', so this patch change ARCH_SPRD to tristate.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200305103228.9686-1-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The (CFS) scheduler has some extra logic catering to systems with SMT, but
that logic won't be compiled in unless the above config is set.
Note that the SMT-centric codepaths are gated by the sched_smt_present
static key, and the SMT sched_domains will only survive if the platform has
SMT. As such, the only impact on !SMT platforms should be a slightly
bigger kernel - no behavioural change.
Distro kernels already enable it, which makes sense since there already are
things like ThunderX2 out in the wild. Enable it for the defconfig.
Some deltas
===========
FWIW my ELF symbol table diff looks something like this:
NAME BEFORE AFTER DELTA
update_sd_lb_stats.constprop.135 0 1864 +1864
find_idlest_group.isra.115 0 1808 +1808
update_numa_stats.isra.121 0 628 +628
select_task_rq_fair 3236 3732 +496
compute_energy.isra.112 0 420 +420
score_nearby_nodes.part.120 0 380 +380
__update_idle_core 0 232 +232
nohz_balance_exit_idle.part.127 0 216 +216
sched_slice.isra.99 0 172 +172
update_load_avg.part.107 0 116 +116
wakeup_preempt_entity.isra.101 0 92 +92
sched_cpu_activate 340 396 +56
pick_next_task_idle 8 56 +48
sched_cpu_deactivate 252 292 +40
show_smt_active 44 80 +36
cpu_smt_mask 0 28 +28
set_next_task_idle 4 32 +28
task_numa_work 680 692 +12
cpu_smt_flags 0 8 +8
enqueue_task_fair 2608 2612 +4
wakeup_preempt_entity.isra.104 92 0 -92
update_load_avg 1028 932 -96
task_numa_migrate 1824 1728 -96
sched_slice.isra.102 172 0 -172
nohz_balance_exit_idle.part.130 216 0 -216
task_numa_find_cpu 2116 1868 -248
score_nearby_nodes.part.123 380 0 -380
compute_energy.isra.115 420 0 -420
update_numa_stats.isra.124 472 0 -472
find_idlest_group.isra.118 1808 0 -1808
update_sd_lb_stats.constprop.138 1864 0 -1864
------------------------------------------------------------------
DELTA SUM +820
As for the sched_domains, this is on a hikey960:
before:
$ cat /proc/sys/kernel/sched_domain/cpu*/domain*/name | sort | uniq
DIE
MC
after:
$ cat /proc/sys/kernel/sched_domain/cpu*/domain*/name | sort | uniq
DIE
MC
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200227191433.31994-3-valentin.schneider@arm.com
To enable kernel critical shutdown feature added critical trip point to
all non CPU sensors to perform shutdown in orderly manner.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rajeshwari <rkambl@codeaurora.org>
Link: https://lore.kernel.org/r/1583394547-12779-2-git-send-email-rkambl@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The CLKREF clocks in GCC are parented by RPM_SMD_LN_BB_CLK, through the
CXO2 pad. Wire this up so that this is properly enabled when need by the
various PHYs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200106080546.3192125-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When an ahash algorithm fallback to another ahash and that fallback is
shaXXX-CE, doing export/import lead to error like this:
alg: ahash: sha1-sun8i-ce export() overran state buffer on test vector 0, cfg=\"import/export\"
This is due to the descsize of shaxxx-ce being larger than struct shaxxx_state
off by an u32.
For fixing this, let's implement export/import which rip the finalize
variant instead of using generic export/import.
Fixes: 6ba6c74dfc ("arm64/crypto: SHA-224/SHA-256 using ARMv8 Crypto Extensions")
Fixes: 2c98833a42 ("arm64/crypto: SHA-1 using ARMv8 Crypto Extensions")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no enable-gpio for backlight control on rk3399 evb,
actually GPIO1_B5 is for LCD panle enable. So remove it from backlight
dt node.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20200305113912.32226-4-andy.yan@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the DT nodes for each of the Network-On-Chip interconnect
buses found on SDM845 based platform and redefine the rsc_hlos
child node as a bcm-voter device to better represent the hardware.
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200209183411.17195-7-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This is just like commit a1875bf982 ("arm64: dts: qcom: sdm845: Add
unit name to soc node") but for sc7180.
For reference, the warning being fixed was:
Warning (unit_address_vs_reg): /soc:
node has a reg or ranges property, but no unit name
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 90db71e480 ("arm64: dts: sc7180: Add minimal dts/dtsi files for SC7180 soc")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200304105638.1.I9ea0d337fcb927f52a28b20613b2377b6249c222@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There are no applicable literals above them.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Remi Denis-Courmont <remi.denis.courmont@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The arch code for hot-remove must tear down portions of the linear map and
vmemmap corresponding to memory being removed. In both cases the page
tables mapping these regions must be freed, and when sparse vmemmap is in
use the memory backing the vmemmap must also be freed.
This patch adds unmap_hotplug_range() and free_empty_tables() helpers which
can be used to tear down either region and calls it from vmemmap_free() and
___remove_pgd_mapping(). The free_mapped argument determines whether the
backing memory will be freed.
It makes two distinct passes over the kernel page table. In the first pass
with unmap_hotplug_range() it unmaps, invalidates applicable TLB cache and
frees backing memory if required (vmemmap) for each mapped leaf entry. In
the second pass with free_empty_tables() it looks for empty page table
sections whose page table page can be unmapped, TLB invalidated and freed.
While freeing intermediate level page table pages bail out if any of its
entries are still valid. This can happen for partially filled kernel page
table either from a previously attempted failed memory hot add or while
removing an address range which does not span the entire page table page
range.
The vmemmap region may share levels of table with the vmalloc region.
There can be conflicts between hot remove freeing page table pages with
a concurrent vmalloc() walking the kernel page table. This conflict can
not just be solved by taking the init_mm ptl because of existing locking
scheme in vmalloc(). So free_empty_tables() implements a floor and ceiling
method which is borrowed from user page table tear with free_pgd_range()
which skips freeing page table pages if intermediate address range is not
aligned or maximum floor-ceiling might not own the entire page table page.
Boot memory on arm64 cannot be removed. Hence this registers a new memory
hotplug notifier which prevents boot memory offlining and it's removal.
While here update arch_add_memory() to handle __add_pages() failures by
just unmapping recently added kernel linear mapping. Now enable memory hot
remove on arm64 platforms by default with ARCH_ENABLE_MEMORY_HOTREMOVE.
This implementation is overall inspired from kernel page table tear down
procedure on X86 architecture and user page table tear down method.
[Mike and Catalin added P4D page table level support]
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The arm64 page table dump code can race with concurrent modification of the
kernel page tables. When a leaf entries are modified concurrently, the dump
code may log stale or inconsistent information for a VA range, but this is
otherwise not harmful.
When intermediate levels of table are freed, the dump code will continue to
use memory which has been freed and potentially reallocated for another
purpose. In such cases, the dump code may dereference bogus addresses,
leading to a number of potential problems.
Intermediate levels of table may by freed during memory hot-remove,
which will be enabled by a subsequent patch. To avoid racing with
this, take the memory hotplug lock when walking the kernel page table.
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Discussing the YAML validation schema with the DT maintainers
it came out that a bus named "smb@80000000" is not really
accepted, and the schema was written to name the static memory
bus just "bus@80000000".
This change is necessary for the schema to kick in and validate
these device trees, else the schema gets ignored.
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- The compatible for Agilex GMAC should be "altr,socfpga-stmmac-a10-s10"
-----BEGIN PGP SIGNATURE-----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=VAHM
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_fix_for_v5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes
arm64: dts: agilex: fix gmac compatible
- The compatible for Agilex GMAC should be "altr,socfpga-stmmac-a10-s10"
* tag 'socfpga_dts_fix_for_v5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: (578 commits)
arm64: dts: socfpga: agilex: Fix gmac compatible
Linux 5.6-rc4
KVM: VMX: check descriptor table exits on instruction emulation
ext4: potential crash on allocation error in ext4_alloc_flex_bg_array()
macintosh: therm_windtunnel: fix regression when instantiating devices
jbd2: fix data races at struct journal_head
kvm: x86: Limit the number of "kvm: disabled by bios" messages
KVM: x86: avoid useless copy of cpufreq policy
KVM: allow disabling -Werror
KVM: x86: allow compiling as non-module with W=1
KVM: Pre-allocate 1 cpumask variable per cpu for both pv tlb and pv ipis
KVM: Introduce pv check helpers
KVM: let declaration of kvm_get_running_vcpus match implementation
KVM: SVM: allocate AVIC data structures based on kvm_amd module parameter
MAINTAINERS: Correct Cadence PCI driver path
io_uring: fix 32-bit compatability with sendmsg/recvmsg
net: dsa: mv88e6xxx: Fix masking of egress port
mlxsw: pci: Wait longer before accessing the device after reset
sfc: fix timestamp reconstruction at 16-bit rollover points
vsock: fix potential deadlock in transport->release()
...
Link: https://lore.kernel.org/r/20200303153509.28248-1-dinguyen@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix gmac compatible string to "altr,socfpga-stmmac-a10-s10". Gmac for
Agilex should use same compatible as Stratix 10.
Fixes: 4b36daf9ad ("arm64: dts: agilex: Add initial support for Intel's Agilex SoCFPGA")
Cc: stable@vger.kernel.org
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This is largely cosmetic, but Odroid N2 and Khadas VIM3 are G12B devices so
correct the card model names to reflect this.
Fixes: aa7d5873bf ("arm64: dts: meson-g12b-odroid-n2: add sound card")
Fixes: c6d29c66e5 ("arm64: dts: meson-g12b-khadas-vim3: add initial device-tree")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[khilman: fix whitespace in commit log trailers]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/1583135051-95529-1-git-send-email-christianshewitt@gmail.com
Since commit f88f42f853 ("arm64: context: Free up kernel ASIDs if KPTI
is not in use"), the NUM_USER_ASIDS macro doesn't correspond to the
effective number of ASIDs when KPTI is enabled. Get an accurate number
of available ASIDs in an arch_initcall, once we've discovered all CPUs'
capabilities and know if we still need to halve the ASID space for KPTI.
Fixes: f88f42f853 ("arm64: context: Free up kernel ASIDs if KPTI is not in use")
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Add support for matching the new PMUs. For now, this just wires them up
as generic PMUv3 such that people writing DTs for new SoCs can do the
right thing, and at least have architectural and raw events be usable.
We can come back and fill in event maps for sysfs and/or perf tools at
a later date.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The PMU init callbacks are already drowning in boilerplate, so before
doubling the number of supported PMU models, give it a sensible refactor
to significantly reduce the bloat, both in source and object code.
Although nobody uses non-default sysfs attributes today, there's minimal
impact to preserving the notion that maybe, some day, somebody might, so
we may as well keep up appearances.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
videostrong kii pro comes with a nec rc, add the keymap to the dts
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
as too large frame sizes on some configurations. On the
ARM side, the compiler was messing up shadow stacks between
EL1 and EL2 code, which is easily fixed with __always_inline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeXAT4AAoJEL/70l94x66DWywH/1kv4MmeGo6PI0Nxk/yvA7X8
78iqIBchtxZX0v/9kqpTB7bYmHyTgmZHM+IkwtIUANDSaOvWqJwU+TLUfduOiuXF
NxBHcZDyuMoftX5CSQ+bJ5PwxKijAdJsIkCZ13CnsTCkwcfamSGypFUCK8LacPeq
WHvV5Ws5pFc51xrP3CH1DrRhLoulaBmt5xxqK9fxWtslrlsnm1uNza5vs8As8CzM
apnmdRIf5p4v91Zic3PFH7/GXES0m1tjIBKdtZ4YHb8yrXV/kBsEVhhTjqE9mrUq
qtRRl5waOFoP4yc9ey52PAbMm1x1Ho/pyunpM0xh40Yq8OPFwqXBPTnWfobSoiM=
=LNQc
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"More bugfixes, including a few remaining "make W=1" issues such as too
large frame sizes on some configurations.
On the ARM side, the compiler was messing up shadow stacks between EL1
and EL2 code, which is easily fixed with __always_inline"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: check descriptor table exits on instruction emulation
kvm: x86: Limit the number of "kvm: disabled by bios" messages
KVM: x86: avoid useless copy of cpufreq policy
KVM: allow disabling -Werror
KVM: x86: allow compiling as non-module with W=1
KVM: Pre-allocate 1 cpumask variable per cpu for both pv tlb and pv ipis
KVM: Introduce pv check helpers
KVM: let declaration of kvm_get_running_vcpus match implementation
KVM: SVM: allocate AVIC data structures based on kvm_amd module parameter
arm64: Ask the compiler to __always_inline functions used by KVM at HYP
KVM: arm64: Define our own swab32() to avoid a uapi static inline
KVM: arm64: Ask the compiler to __always_inline functions used at HYP
kvm: arm/arm64: Fold VHE entry/exit work into kvm_vcpu_run_vhe()
KVM: arm/arm64: Fix up includes for trace.h
before
[6.418252] brcmfmac: F1 signature read @0x18000000=0x17224356
[6.435663] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.551259] brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed
[6.551275] brcmfmac: brcmf_sdio_verifymemory: error -84 on reading 2048 membytes at 0x00184000
[6.551352] brcmfmac: brcmf_sdio_download_firmware: dongle image file download failed
after
[6.657165] brcmfmac: F1 signature read @0x18000000=0x17224356
[6.660807] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.918643] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.918734] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[6.922724] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4356/2 wl0: Jun 16 2015 14:25:06 version 7.35.184.r1 (TOB) (r559293) FWID 01-b22ae69c
Fixes: adc52bf7ef ("arm64: dts: meson: fix mmc v2 chips max frequencies")
Suggested-by: Art Nikpal <email2tema@gmail.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/1582212790-11402-1-git-send-email-christianshewitt@gmail.com
The lvds controller has two ports. port@0 for the connection
to the display controller(s) and port@1 for the connection to
the panel, so should have a ports node covering the port@x nodes.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20200121222055.4068166-1-heiko@sntech.de
Some rockchip SoCs like the RK3399 and RK3328 exhibit an issue
where tx checksumming does not work with packets larger than 1498.
The default Programmable Buffer Length for TX in these GMAC's is
not suitable for MTUs higher than 1498. The workaround is to disable
TX offloading with 'ethtool -K eth0 tx off rx off' causing performance
impacts as it disables hardware checksumming.
This patch sets snps,txpbl to 0x4 which is a safe number tested ok for
the most popular MTU value of 1500.
For reference, see https://lkml.org/lkml/2019/4/1/1382.
Signed-off-by: Carlos de Paula <me@carlosedp.com>
Link: https://lore.kernel.org/r/20200218221040.10955-1-me@carlosedp.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399pro-rock-pi-n10.dt.yaml: /: compatible:
['radxa,rockpi-n10', 'rockchip,rk3399pro']
is not valid under any of the given schemas
During the review process the binding was changed,
but the dts file was somehow not updated.
Fix this error by adding 'vamrs,rk3399pro-vmarc-som' to
the compatible property.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228061436.13506-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives these errors:
arch/arm64/boot/dts/rockchip/px30-evb.dt.yaml: usb@ff300000:
'g-use-dma', 'power-domains' do not match any of the regexes:
'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3328-a1.dt.yaml: usb@ff580000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3328-evb.dt.yaml: usb@ff580000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3328-rock64.dt.yaml: usb@ff580000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dt.yaml: usb@ff580000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
'g-use-dma' is not a valid option in dwc2.yaml, so remove it
from all Rockchip dtsi files.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/dwc2.yaml
g-use-dma was deprecated in november 2016, see
https://patchwork.kernel.org/patch/9420553/
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228113922.20266-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example these errors:
arch/arm64/boot/dts/rockchip/rk3308-evb.dt.yaml: cpu@0: compatible:
Additional items are not allowed ('arm,armv8' was unexpected)
arch/arm64/boot/dts/rockchip/rk3308-evb.dt.yaml: cpu@0: compatible:
['arm,cortex-a35', 'arm,armv8']
is too long
Fix these errors by removing the last argument of
the cpu compatible property in rk3308.dtsi.
make ARCH=arm64
dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/cpus.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20200228084827.16198-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, and an expansion header.
Additionally there is a HDMI port, DSI port, and camera port only
on the MT8167 version of the board.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8516
board on the eMMC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT8516 SoC provides the following peripherals: GPIO, UART, USB2,
SPI, eMMC, SDIO, NAND, Flash, ADC, I2C, PWM, Timers, IR, Ethernet, and
Audio (I2S, SPDIF, TDM).
This commit is adding the basic dtsi file with the support of the
following IOs: GPIO, UART, SPI, eMMC, I2C, Timers.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This was missed from the previous fix.
Fixes: b07a11dbdf ("arm64: dts: meson-gxbb-vega-s95: fix WiFi/BT module support")
Suggested-by: Oleg Ivanov <balbes-150@yandex.ru>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1582220642-14133-1-git-send-email-christianshewitt@gmail.com
This removes the uart_A alias (no longer required) and adds the bluetooth
node to the P212 device tree.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1582216366-12964-1-git-send-email-christianshewitt@gmail.com
Fixes: adc52bf7ef ("arm64: dts: meson: fix mmc v2 chips max frequencies")
before
[6.418252] brcmfmac: F1 signature read @0x18000000=0x17224356
[6.435663] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.551259] brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed
[6.551275] brcmfmac: brcmf_sdio_verifymemory: error -84 on reading 2048 membytes at 0x00184000
[6.551352] brcmfmac: brcmf_sdio_download_firmware: dongle image file download failed
after
[6.657165] brcmfmac: F1 signature read @0x18000000=0x17224356
[6.660807] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.918643] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.918734] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[6.922724] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4356/2 wl0: Jun 16 2015 14:25:06 version 7.35.184.r1 (TOB) (r559293) FWID 01-b22ae69c
Suggested-by: Art Nikpal <email2tema@gmail.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/1582212790-11402-1-git-send-email-christianshewitt@gmail.com
A codec node of the sei510 sound card is numbered with the pattern
codec@XX. This pattern should be used only if there is a reg property in
the node which is not case here. Change this to something acceptable.
This change is only to better comply with the DT spec. No functional
changes expected.
Fixes: 64c10554bf ("arm64: dts: meson: sei510: add sound card")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200224150812.263980-4-jbrunet@baylibre.com
Some codec nodes of the s400 sound card are numbered with the pattern
codec@XX. This pattern should be used only if there is a reg property in
the node which is not case here. Change this to something acceptable.
This change is only to better comply with the DT spec. No functional
changes expected.
Fixes: 6f59dc1afb ("arm64: dts: meson-axg: s400: add sound card")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200224150812.263980-3-jbrunet@baylibre.com
When high load on the DWC3 SuperSpeed port, the controller crashes with:
[ 221.141621] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
[ 221.157631] xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
[ 221.157635] xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
[ 221.159901] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
[ 221.159961] hub 2-1.1:1.0: hub_ext_port_status failed (err = -22)
[ 221.160076] xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
[ 221.165946] usb 2-1.1-port1: cannot reset (err = -22)
Setting the parkmode_disable_ss_quirk quirk fixes the issue.
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
CC: Dongjin Kim <tobetter@gmail.com>
Link: https://lore.kernel.org/r/20200221091532.8142-4-narmstrong@baylibre.com
videostrong kii pro comes with a nec rc, add the keymap to the dts
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200214085802.28742-4-mohammad.rasim96@gmail.com
Commit 9f9223778 ("efi/libstub/arm: Make efi_entry() an ordinary PE/COFF
entrypoint") modified the handover code written in assembler, and for
maintainability, aligned the logic with the logic used in the 32-bit ARM
version, which is to avoid cache maintenance on the remaining instructions
in the subroutine that will be executed with the MMU and caches off, and
instead, branch into the relocated copy of the kernel image.
However, this assumes that this copy is executable, and this means we
expect EFI_LOADER_DATA regions to be executable as well, which is not
a reasonable assumption to make, even if this is true for most UEFI
implementations today.
So change this back, and add a __clean_dcache_area_poc() call to cover
the remaining code in the subroutine. While at it, switch the other
call site over to __clean_dcache_area_poc() as well, and clean up the
terminology in comments to avoid using 'flush' in the context of cache
maintenance. Also, let's switch to the new style asm annotations.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20200228121408.9075-6-ardb@kernel.org
Follow the standard nodename pattern "^nand-controller(@.*)?" defined
in Documentation/devicetree/bindings/mtd/nand-controller.yaml
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm64 dtbs_check' will show warnings like this:
nand@68000000: $nodename:0: 'nand@68000000' does not match '^nand-controller(@.*)?'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^interrupt-controller(@[0-9a-f,]+)*$"
defined in schemas/interrupt-controller.yaml of dt-schema.
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm64 dtbs_check' will show warnings like this:
aidet@5fc20000: $nodename:0: 'aidet@5fc20000' does not match '^interrupt-controller(@[0-9a-f,]+)*$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^mmc(@.*)?$" defined in
Documentation/devicetree/bindings/mmc/mmc-controller.yaml
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm64 dtbs_check' will show warnings like this:
sdhc@5a000000: $nodename:0: 'sdhc@5a000000' does not match '^mmc(@.*)?$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 25b92693a1 ("arm64: mm: convert cpu_do_switch_mm() to C") added
a new use of the ASID() macro, so update the comment in asm/mmu.h which
reasons about why an atomic reload of 'mm->context.id.counter' is not
required.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Fix compilation on 32bit
- Move VHE guest entry/exit into the VHE-specific entry code
- Make sure all functions called by the non-VHE HYP code is tagged as __always_inline
-----BEGIN PGP SIGNATURE-----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=NpPo
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm fixes for 5.6, take #1
- Fix compilation on 32bit
- Move VHE guest entry/exit into the VHE-specific entry code
- Make sure all functions called by the non-VHE HYP code is tagged as __always_inline
Our new dev board (Huawei D06CS) has a MegaRAID SAS HBA as the storage
controller, and we cannot access the HiSilicon SAS HBA, which we normally
use; so enable the driver config option so we can boot a distro with the
default defconfig.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The qcom-tsens binding requires a SoC-specific and a TSENS
family-specific binding to be specified in the compatible string.
Since them family-specific binding is not listed in the .dtsi file, we
see the following warnings in 'make dtbs_check'. Fix them.
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4a9000: compatible: ['qcom,msm8996-tsens'] is not valid
under any of the given schemas (Possible causes of the failure):
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4a9000: compatible: ['qcom,msm8996-tsens'] is too short
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4a9000: compatible:0: 'qcom,msm8996-tsens' is not one of
['qcom,msm8916-tsens', 'qcom,msm8974-tsens']
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4a9000: compatible:0: 'qcom,msm8996-tsens' is not one of
['qcom,msm8976-tsens', 'qcom,qcs404-tsens']
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4ad000: compatible: ['qcom,msm8996-tsens'] is not valid
under any of the given schemas (Possible causes of the failure):
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4ad000: compatible: ['qcom,msm8996-tsens'] is too short
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4ad000: compatible:0: 'qcom,msm8996-tsens' is not one of
['qcom,msm8916-tsens', 'qcom,msm8974-tsens']
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4ad000: compatible:0: 'qcom,msm8996-tsens' is not one of
['qcom,msm8976-tsens', 'qcom,qcs404-tsens']
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/ebaa801adade53c567857db2f74af7d2e00f935b.1582871139.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The qcom-tsens binding requires a SoC-specific and a TSENS
family-specific binding to be specified in the compatible string.
Since them family-specific binding is not listed in the .dtsi file, we
see the following warnings in 'make dtbs_check'. Fix them.
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml:
thermal-sensor@4a9000: compatible: ['qcom,msm8916-tsens'] is not valid
under any of the given schemas (Possible causes of the failure):
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml:
thermal-sensor@4a9000: compatible: ['qcom,msm8916-tsens'] is too short
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml:
thermal-sensor@4a9000: compatible:0: 'qcom,msm8916-tsens' is not one of
['qcom,msm8976-tsens', 'qcom,qcs404-tsens']
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml:
thermal-sensor@4a9000: compatible:0: 'qcom,msm8916-tsens' is not one of
['qcom,msm8996-tsens', 'qcom,msm8998-tsens', 'qcom,sdm845-tsens']
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/8cea8c0036703bcc4dd2b87a8ca3913c4a28d16e.1582871139.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Bring in the Truly display and enable the DSI channels to make the
mdss/gpu probe, even though we're lacking LABIB, preventing us from
seeing anything on the screen.
Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Link: https://lore.kernel.org/r/20190513210747.22429-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Per convention device nodes for SC7180 should be ordered by address.
This is currently not the case for the venus node, move it to the
correct position.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200227092649.v3.1.I15e0f7eff0c67a2b49d4992f9d80fc1d2fdadf63@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move all pmdomain and clock resources to Venus DT node. And make
possible to support dynamic core assignment on v4.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Link: https://lore.kernel.org/r/20200106154929.4331-12-stanimir.varbanov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently arm64 doesn't initialize the primary CRNG in a (potentially)
trusted manner as we only detect the presence of the RNG once secondary
CPUs are up.
Now that the core RNG code distinguishes the early initialization of the
primary CRNG, we can implement arch_get_random_seed_long_early() to
support this.
This patch does so.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200210130015.17664-4-mark.rutland@arm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
-----BEGIN PGP SIGNATURE-----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=8Bsc
-----END PGP SIGNATURE-----
Merge tag 'tee-amdtee-fix-for-5.6' of https://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes
Fix AMDTEE memory leak in amdtee_open_session()
* tag 'tee-amdtee-fix-for-5.6' of https://git.linaro.org/people/jens.wiklander/linux-tee: (344 commits)
tee: amdtee: fix memory leak in amdtee_open_session()
Linux 5.6-rc2
ext4: improve explanation of a mount failure caused by a misconfigured kernel
Input: cyapa - replace zero-length array with flexible-array member
Input: tca6416-keypad - replace zero-length array with flexible-array member
Input: gpio_keys_polled - replace zero-length array with flexible-array member
IB/mlx5: Use div64_u64 for num_var_hw_entries calculation
nvme: fix the parameter order for nvme_get_log in nvme_get_fw_slot_info
nvme/pci: move cqe check after device shutdown
nvme: prevent warning triggered by nvme_stop_keep_alive
nvme/tcp: fix bug on double requeue when send fails
cifs: make sure we do not overflow the max EA buffer size
cifs: enable change notification for SMB2.1 dialect
netdevice.h: fix all kernel-doc and Sphinx warnings
net: dsa: tag_ar9331: Make sure there is headroom for tag
net: dsa: tag_qca: Make sure there is headroom for tag
net, ip6_tunnel: enhance tunnel locate with link check
net/smc: no peer ID in CLC decline for SMCD
net/smc: transfer fasync_list in case of fallback
net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples()
...
Link: https://lore.kernel.org/r/20200227165205.GA7926@jade
Signed-off-by: Olof Johansson <olof@lixom.net>
- Restore R-Car M3-W support,
- Drop deprecated compatible value to ease DT binding conversion to
json-schema.
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXlY78AAKCRCKwlD9ZEnx
cAR9APdKGcY7roK82m1uLIsCohHOdwikY4qvR+cVniRKgwspAP9Q3NNCXhelEEed
S2JMLficspDnR+BuWR3gyg173Z74CQ==
=P/qq
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas Fixes for v5.6
- Restore R-Car M3-W support,
- Drop deprecated compatible value to ease DT binding conversion to
json-schema.
* tag 'renesas-fixes-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: r8a7779: Remove deprecated "renesas, rcar-sata" compatible value
arm64: defconfig: Replace ARCH_R8A7796 by ARCH_R8A77960
Link: https://lore.kernel.org/r/20200226105236.18368-1-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
There's no reason that cpu_do_switch_mm() needs to be written as an
assembly function, and having it as a C function would make it easier to
maintain.
This patch converts cpu_do_switch_mm() to C, removing code that this
change makes redundant (e.g. the mmid macro). Since the header comment
was stale and the prototype now implies all the necessary information,
this comment is removed. The 'pgd_phys' argument is made a phys_addr_t
to match the return type of virt_to_phys().
At the same time, post_ttbr_update_workaround() is updated to use
IS_ENABLED(), which allows the compiler to figure out it can elide calls
for !CONFIG_CAVIUM_ERRATUM_27456 builds.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
[catalin.marinas@arm.com: change comments from asm-style to C-style]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix typos in arch/arm64/Kconfig:
- spell Numa as NUMA
- add hyphenation to Non-Uniform
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
At the moment PinePhone comes in two slightly incompatible variants:
- 1.0: Early Developer Batch
- 1.1: Braveheart Batch
There will be at least one more incompatible variant in the very near
future, so let's start by sharing the dtsi among multiple variants,
right away, even though the HW description doesn't yet include the
different bits.
The differences between 1.0 and 1.1 are: change in pins that control
the flash LED, differences in modem power status signal routing, and
maybe some other subtler things, that have not been determined yet.
This is a basic DT that includes only features that are already
supported by mainline drivers.
Co-developed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Co-developed-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
PinePhone needs I2C2 pins description. Add it, and make it default
for i2c2, since it's the only possiblilty.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Pinebook has an ANX6345 bridge connected to the RGB666 LCD output and
eDP panel input. The bridge is controlled via I2C that's connected to
R_I2C bus.
Enable all this hardware in device tree.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This time, the set of changes for the EFI subsystem is much larger than
usual. The main reasons are:
- Get things cleaned up before EFI support for RISC-V arrives, which will
increase the size of the validation matrix, and therefore the threshold to
making drastic changes,
- After years of defunct maintainership, the GRUB project has finally started
to consider changes from the distros regarding UEFI boot, some of which are
highly specific to the way x86 does UEFI secure boot and measured boot,
based on knowledge of both shim internals and the layout of bootparams and
the x86 setup header. Having this maintenance burden on other architectures
(which don't need shim in the first place) is hard to justify, so instead,
we are introducing a generic Linux/UEFI boot protocol.
Summary of changes:
- Boot time GDT handling changes (Arvind)
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file I/O,
memory allocation, etc.
- Introduce a generic initrd loading method based on calling back into
the firmware, instead of relying on the x86 EFI handover protocol or
device tree.
- Introduce a mixed mode boot method that does not rely on the x86 EFI
handover protocol either, and could potentially be adopted by other
architectures (if another one ever surfaces where one execution mode
is a superset of another)
- Clean up the contents of struct efi, and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit firmware
implementations to return EFI_UNSUPPORTED from UEFI runtime services at
OS runtime, and expose a mask of which ones are supported or unsupported
via a configuration table.
- Various documentation updates and minor code cleanups (Heinrich)
- Partial fix for the lack of by-VA cache maintenance in the decompressor
on 32-bit ARM. Note that these patches were deliberately put at the
beginning so they can be used as a stable branch that will be shared with
a PR containing the complete fix, which I will send to the ARM tree.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEnNKg2mrY9zMBdeK7wjcgfpV0+n0FAl5S7WYACgkQwjcgfpV0
+n1jmQgAmwV3V8pbgB4mi4P2Mv8w5Zj5feUe6uXnTR2AFv5nygLcTzdxN+TU/6lc
OmZv2zzdsAscYlhuUdI/4t4cXIjHAZI39+UBoNRuMqKbkbvXCFscZANLxvJjHjZv
FFbgUk0DXkF0BCEDuSLNavidAv4b3gZsOmHbPfwuB8xdP05LbvbS2mf+2tWVAi2z
ULfua/0o9yiwl19jSS6iQEPCvvLBeBzTLW7x5Rcm/S0JnotzB59yMaeqD7jO8JYP
5PvI4WM/l5UfVHnZp2k1R76AOjReALw8dQgqAsT79Q7+EH3sNNuIjU6omdy+DFf4
tnpwYfeLOaZ1SztNNfU87Hsgnn2CGw==
=pDE3
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/core
Pull EFI updates for v5.7 from Ard Biesheuvel:
This time, the set of changes for the EFI subsystem is much larger than
usual. The main reasons are:
- Get things cleaned up before EFI support for RISC-V arrives, which will
increase the size of the validation matrix, and therefore the threshold to
making drastic changes,
- After years of defunct maintainership, the GRUB project has finally started
to consider changes from the distros regarding UEFI boot, some of which are
highly specific to the way x86 does UEFI secure boot and measured boot,
based on knowledge of both shim internals and the layout of bootparams and
the x86 setup header. Having this maintenance burden on other architectures
(which don't need shim in the first place) is hard to justify, so instead,
we are introducing a generic Linux/UEFI boot protocol.
Summary of changes:
- Boot time GDT handling changes (Arvind)
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file I/O,
memory allocation, etc.
- Introduce a generic initrd loading method based on calling back into
the firmware, instead of relying on the x86 EFI handover protocol or
device tree.
- Introduce a mixed mode boot method that does not rely on the x86 EFI
handover protocol either, and could potentially be adopted by other
architectures (if another one ever surfaces where one execution mode
is a superset of another)
- Clean up the contents of struct efi, and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit firmware
implementations to return EFI_UNSUPPORTED from UEFI runtime services at
OS runtime, and expose a mask of which ones are supported or unsupported
via a configuration table.
- Various documentation updates and minor code cleanups (Heinrich)
- Partial fix for the lack of by-VA cache maintenance in the decompressor
on 32-bit ARM. Note that these patches were deliberately put at the
beginning so they can be used as a stable branch that will be shared with
a PR containing the complete fix, which I will send to the ARM tree.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Enable the drivers for the display and gpu clock controllers on Qualcomm
SDM845, needed in order to get these features working. These drivers
provides power-domains and can as such not be compiled as modules.
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20191109024234.1757452-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The commit 7aa9b9eb7d ("arm64: dts: allwinner: H6: Add PMU mode")
introduced support for the PMU found on the Allwinner H6. However, the
binding only allows for a single compatible, while the patch was adding
two.
Make sure we follow the binding.
Fixes: 7aa9b9eb7d ("arm64: dts: allwinner: H6: Add PMU mode")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The commit c35a516a46 ("arm64: dts: allwinner: H5: Add PMU node")
introduced support for the PMU found on the Allwinner H5. However, the
binding only allows for a single compatible, while the patch was adding
two.
Make sure we follow the binding.
Fixes: c35a516a46 ("arm64: dts: allwinner: H5: Add PMU node")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add the display, video & graphics clock controller nodes supported on
SC7180.
NOTE: the dispcc needs input clocks from various PHYs that aren't in
the device tree yet. For now we'll leave these stubbed out with <0>,
which is apparently the magic way to do this. These clocks aren't
really "optional" and this stubbing out method is apparently the best
way to handle it.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200203103049.v4.15.I1a4b93fb005791e29a9dcf288fc8bd459a555a59@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We're transitioning over to requiring the Qualcomm Video Clock
Controller to specify all the input clocks. Let's add the one input
clock for the videocc for sdm845.
NOTE: Until the Linux driver for sdm845's video is updated, this clock
will not actually be used in Linux. It will continue to use global
clock names to match things up.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200203103049.v4.14.Id0599319487f075808baba7cba02c4c3c486dc80@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We're transitioning over to requiring the Qualcomm GPU Clock
Controller to specify all the input clocks. Let's add them for
sdm845.
As part of this we've decided that the xo clock should be referred to
in the bindings as "bi_tcxo". Change the dts.
NOTE: Until the Linux driver for sdm845's gpucc is updated, these
clocks will not actually be used in Linux. It will continue to use
global clock names to match things up. Of course, Linux didn't use
the old "xo" clock anyway.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200203103049.v4.8.If8596faf02408cef4bb9f52296b911eb9ba49287@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We're transitioning over to requiring the Qualcomm Display Clock
Controller to specify all the input clocks. Let's add them for
sdm845.
NOTES:
- Until the Linux driver for sdm845's dispcc is updated, these clocks
will not actually be used in Linux. It will continue to use global
clock names to match things up.
- Although the clocks from the DP PHY are required, the DP PHY isn't
represented in the dts yet. Apparently the magic for this is just
to use <0>.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200203103049.v4.3.Ie80fa74e1774f4317d80d70d30ef4b78f16cc8df@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As per the bindings, the SDHCI controller should have a SoC-specific
compatible string in addition to the generic version-based one. Add
it.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Fixes: 7241ab944d ("arm64: dts: qcom: qcs404: Add sdcc1 node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200127082331.1.I402470e4a162d69fde47ee2ea708b15bde9751f9@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds the gpio-ranges property to almost all of
the Qualcomm ARM platforms that utilize the pinctrl-msm
framework.
The gpio-ranges property is part of the gpiolib subsystem.
As a result, the binding text is available in section
"2.1 gpio- and pin-controller interaction" of
Documentation/devicetree/bindings/gpio/gpio.txt
For more information please see the patch titled:
"pinctrl: msm: fix gpio-hog related boot issues" from
this series.
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019]
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Robert Marko <robert.marko@sartura.hr> [ipq4019]
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20200108125455.308969-2-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some platforms don't want to use the pmic power key as the power key
event. Add a label so platforms can easily reference and mark this node
as status = "disabled".
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Kiran Gunda <kgunda@codeaurora.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200115025314.3054-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl5TuEMUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4a+Qf9Enb2G47LTMeYH5JYhm2anDQ4lz+8
Og1bcGPYKilDhc4YzpAIhRnOTLa9TietZSS0tyNFk37GDfKRjn9gxXDRbI+4lrJc
UOSLpWCB4BnzKc+FoCHC37jkdkMD3V2E5MmFHtYkGYmH0DAi8cLmGebmgGujd0GJ
lx2/5EbxKoJxeA2i79H5OAPBhglJsEnPTSulZ+jUdLzJfBlRBIQBc3oPcwnRIibr
VUbLc4Gkb2kTe6NwdQTjqI+4BTHv7/4m+twOojO5Z8QBH4X+3bkLnLiylhuqHBeR
cDXGL7sHkekZhDQ3OwIMiT/5cc8SxplqAl6QMm8+/9gq7KfAucy8Psokow==
=dg69
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.6:
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
* tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx-scu: Align imx sc msg structs to 4
firmware: imx: Align imx_sc_msg_req_cpu_start to 4
firmware: imx: scu-pd: Align imx sc msg structs to 4
firmware: imx: misc: Align imx sc msg structs to 4
firmware: imx: scu: Ensure sequential TX
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
arm64: dts: imx8qxp-mek: Remove unexisting Ethernet PHY
ARM: dts: imx6dl-colibri-eval-v3: fix sram compatible properties
ARM: dts: ls1021a: Restore MDIO compatible to gianfar
ARM: dts: imx7d: fix opp-supported-hw
ARM: imx: build v7_cpu_resume() unconditionally
ARM: dts: imx6: phycore-som: fix emmc supply
Link: https://lore.kernel.org/r/20200224120334.GH27688@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Orange Pi PC2 features sy8106a regulator just like Orange Pi PC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
According to latest datasheet Rev.0, 10/2019, there is restriction
as below:
"If VDD_SOC/GPU/DDR = 0.95V, then VDD_ARM must be >= 0.95V."
As by default SoC is running at OD mode(VDD_SOC = 0.95V), so
VDD_ARM 1.2GHz OPP's voltage should be increased to 0.95V.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
System counter timer is necessary as broadcast timer for cpu-idle,
add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MP EVK board has a GPIO LED to indicate status, add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mq-evk has a GPIO connected to AR8031 Ethernet PHY's reset pin.
Describe it in the device tree, following phy's datasheet reset duration of 10ms.
Tested booting via NFS.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mm-evk has a GPIO connected to AR8031 Ethernet PHY's reset pin.
Describe it in the device tree, following phy's datasheet reset duration of 10ms.
Tested booting via NFS.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we have added new ways to load the initrd or the mixed mode
kernel, we will also need a way to tell the loader about this. Add
symbolic constants for the PE/COFF major/minor version numbers (which
fortunately have always been 0x0 for all architectures), so that we
can bump them later to document the capabilities of the stub.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
We currently parse the command non-destructively, to avoid having to
allocate memory for a copy before passing it to the standard parsing
routines that are used by the core kernel, and which modify the input
to delineate the parsed tokens with NUL characters.
Instead, we call strstr() and strncmp() to go over the input multiple
times, and match prefixes rather than tokens, which implies that we
would match, e.g., 'nokaslrfoo' in the stub and disable KASLR, while
the kernel would disregard the option and run with KASLR enabled.
In order to avoid having to reason about whether and how this behavior
may be abused, let's clean up the parsing routines, and rebuild them
on top of the existing helpers.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The arm64 kernel no longer requires the FDT blob to fit inside a
naturally aligned 2 MB memory block, so remove the code that aligns
the allocation to 2 MB.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Instead of setting the visibility pragma for a small set of symbol
declarations that could result in absolute references that we cannot
support in the stub, declare hidden visibility for all code in the
EFI stub, which is more robust and future proof.
To ensure that the #pragma is taken into account before any other
includes are processed, put it in a header file of its own and
include it via the compiler command line using the -include option.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Expose efi_entry() as the PE/COFF entrypoint directly, instead of
jumping into a wrapper that fiddles with stack buffers and other
stuff that the compiler is much better at. The only reason this
code exists is to obtain a pointer to the base of the image, but
we can get the same value from the loaded_image protocol, which
we already need for other reasons anyway.
Update the return type as well, to make it consistent with what
is required for a PE/COFF executable entrypoint.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
KVM uses some of the static-inline helpers like icache_is_vipt() from
its HYP code. This assumes the function is inlined so that the code is
mapped to EL2. The compiler may decide not to inline these, and the
out-of-line version may not be in the __hyp_text section.
Add the additional __always_ hint to these static-inlines that are used
by KVM.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200220165839.256881-4-james.morse@arm.com
KVM uses swab32() when mediating GIC MMIO accesses if the GICV is badly
aligned, and the host and guest differ in endianness.
arm64 doesn't provide a __arch_swab32(), so __fswab32() is always backed
by the macro implementation that the compiler reduces to a single
instruction. But the static-inline causes problems for KVM if the compiler
chooses not to inline this function, it may not be located in the
__hyp_text where __vgic_v2_perform_cpuif_access() needs it.
Create our own __kvm_swab32() macro that calls ___constant_swab32()
directly. This way we know it will always be inlined.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200220165839.256881-3-james.morse@arm.com
On non VHE CPUs, KVM's __hyp_text contains code run at EL2 while the rest
of the kernel runs at EL1. This code lives in its own section with start
and end markers so we can map it to EL2.
The compiler may decide not to inline static-inline functions from the
header file. It may also decide not to put these out-of-line functions
in the same section, meaning they aren't mapped when called at EL2.
Clang-9 does exactly this with __kern_hyp_va() and a few others when
x18 is reserved for the shadow call stack. Add the additional __always_
hint to all the static-inlines that are called from a hyp file.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200220165839.256881-2-james.morse@arm.com
----
kvm_get_hyp_vector() pulls in all the regular per-cpu accessors
and this_cpu_has_cap(), fortunately its only called for VHE.
- Fix regression in malloc() caused by ignored address tags in brk()
- Add missing brackets around argument to untagged_addr() macro
- Fix clang build when using binutils assembler
- Fix silly typo in virtual memory map documentation
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl5P2VIQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNNn9CACN/C0aTsRT+22ABPahHcnnyQgsETMOS3Up
M/edlPMUI5qK8IcIBt/PKswzBKlwMpI/pCWxfn/kwdq9u0ho3IASnqtaBVcm7yjt
d/4DX5GhwJBdv6q6N+vjacrqs3e/xCiDiWqLvhEVZXTFuDxNMziCfloP6sDBxmYu
E0+zuZnMbVemgV7USo+7QXMeNb7kFwP6fmJN0cr/FG7N4orms2zygs6mhg/ogpkH
zdl7Ze6DdC5+ChLpLhGXEuA2+Gyv+tWoE7A1EXnTGSEEQXmH7FkaZOJxAuSbWgw6
8Gcul+0JSHRBHN876oqS9aSr88ZiZDZkccC2gLW2Off6vvv8Rgog
=ehao
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"It's all straightforward apart from the changes to mmap()/mremap() in
relation to their handling of address arguments from userspace with
non-zero tag bits in the upper byte.
The change to brk() is necessary to fix a nasty user-visible
regression in malloc(), but we tightened up mmap() and mremap() at the
same time because they also allow the user to create virtual aliases
by accident. It's much less likely than brk() to matter in practice,
but enforcing the principle of "don't permit the creation of mappings
using tagged addresses" leads to a straightforward ABI without having
to worry about the "but what if a crazy program did foo?" aspect of
things.
Summary:
- Fix regression in malloc() caused by ignored address tags in brk()
- Add missing brackets around argument to untagged_addr() macro
- Fix clang build when using binutils assembler
- Fix silly typo in virtual memory map documentation"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
mm: Avoid creating virtual address aliases in brk()/mmap()/mremap()
docs: arm64: fix trivial spelling enought to enough in memory.rst
arm64: memory: Add missing brackets to untagged_addr() macro
arm64: lse: Fix LSE atomics with LLVM
Add reset control properties to the device nodes for the Display Units
on all supported RZ/G2 SoCs. Note that on these SoCs, there is only a
single reset for each pair of DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-5-geert+renesas@glider.be
Add reset control properties to the device nodes for the Display Units
on all supported R-Car Gen3 SoCs. Note that on these SoCs, there is
only a single reset for each pair of DU channels.
The display nodes on R-Car V3M and V3H already had "resets" properties,
but lacked the corresponding "reset-names" properties.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-4-geert+renesas@glider.be
CONFIG_ARCH_R8A7795 was split in CONFIG_ARCH_R8A77950 and
CONFIG_ARCH_R8A77951 in commit b925adfceb ("soc: renesas: Add
ARCH_R8A7795[01] for existing R-Car H3"), so its users can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218112414.5591-1-geert+renesas@glider.be
Add device nodes for the CryptoCell instances on the various Renesas
R-Car Gen3 SoCs that do not have support for them yet in their device
trees (M3-W, M3-W+, M3-N, E3, D3).
The R-Car H3 device tree already supports this device.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200124133330.16121-1-geert+renesas@glider.be
The Renesas-specific "vsps" property lacks a vendor prefix.
Add a "renesas," prefix to comply with DT best practises.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20191105183504.21447-4-geert+renesas@glider.be
The r8a77970 was added with a compatible string for a different device
rather than adding the correct compatible to the driver.
Remove the unnecessary compatible which is for a different platform.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190912103734.1879-1-kieran.bingham+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The #cooling-cells property needs to be specified to allow a CPU
to be used as cooling device.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add dynamic power coefficients for all cores.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
[mb: fix commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The syscall slow path is spuriously invoked when context tracking is
activated while the entry code calls context tracking from fast path.
Remove that overhead and the unused flag itself while at it.
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Add brackets around the evaluation of the 'addr' parameter to the
untagged_addr() macro so that the cast to 'u64' applies to the result
of the expression.
Cc: <stable@vger.kernel.org>
Fixes: 597399d0cb ("arm64: tags: Preserve tags for addresses translated via TTBR1")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will@kernel.org>
The LS1028A has three (dual) SPI controller. These are compatible with
the ones from the LS1021A. Add the nodes.
The third controller was tested on a custom board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is only on Ethernet port and one Ethernet PHY on imx8qxp-mek.
Remove the unexisting ethphy1 port.
This fixes a run-time warning:
mdio_bus 5b040000.ethernet-1: MDIO device at address 1 is missing.
Fixes: fdea904e85 ("arm64: dts: imx: add imx8qxp mek support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit e0d5896bd3 ("arm64: lse: fix LSE atomics with LLVM's integrated
assembler") broke the build when clang is used in connjunction with the
binutils assembler ("-no-integrated-as"). This happens because
__LSE_PREAMBLE is defined as ".arch armv8-a+lse", which overrides the
version of the CPU architecture passed via the "-march" paramter to gas:
$ aarch64-none-linux-gnu-as -EL -I ./arch/arm64/include
-I ./arch/arm64/include/generated
-I ./include -I ./include
-I ./arch/arm64/include/uapi
-I ./arch/arm64/include/generated/uapi
-I ./include/uapi -I ./include/generated/uapi
-I ./init -I ./init
-march=armv8.3-a -o init/do_mounts.o
/tmp/do_mounts-d7992a.s
/tmp/do_mounts-d7992a.s: Assembler messages:
/tmp/do_mounts-d7992a.s:1959: Error: selected processor does not support `autiasp'
/tmp/do_mounts-d7992a.s:2021: Error: selected processor does not support `paciasp'
/tmp/do_mounts-d7992a.s:2157: Error: selected processor does not support `autiasp'
/tmp/do_mounts-d7992a.s:2175: Error: selected processor does not support `paciasp'
/tmp/do_mounts-d7992a.s:2494: Error: selected processor does not support `autiasp'
Fix the issue by replacing ".arch armv8-a+lse" with ".arch_extension lse".
Sami confirms that the clang integrated assembler does now support the
'.arch_extension' directive, so this change will be fine even for LTO
builds in future.
Fixes: e0d5896bd3 ("arm64: lse: fix LSE atomics with LLVM's integrated assembler")
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Reported-by: Amit Kachhap <Amit.Kachhap@arm.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Now that all architectures are converted to use the generic storage the
helpers and conditionals can be removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lkml.kernel.org/r/20200207124403.470699892@linutronix.de
Convert ARM/ARM64 to the generic VDSO clock mode storage. This needs to
happen in one go as they share the clocksource driver.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lkml.kernel.org/r/20200207124403.363235229@linutronix.de
With VHE, running a vCPU always requires the sequence:
1. kvm_arm_vhe_guest_enter();
2. kvm_vcpu_run_vhe();
3. kvm_arm_vhe_guest_exit()
... and as we invoke this from the shared arm/arm64 KVM code, 32-bit arm
has to provide stubs for all three functions.
To simplify the common code, and make it easier to make further
modifications to the arm64-specific portions in the near future, let's
fold kvm_arm_vhe_guest_enter() and kvm_arm_vhe_guest_exit() into
kvm_vcpu_run_vhe().
The 32-bit stubs for kvm_arm_vhe_guest_enter() and
kvm_arm_vhe_guest_exit() are removed, as they are no longer used. The
32-bit stub for kvm_vcpu_run_vhe() is left as-is.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200210114757.2889-1-mark.rutland@arm.com
The nodes with name scpsys actually implement a power-controller.
Rename the nodes to match the bindings description.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
