[ Upstream commit 0410d07190 ]
When the ARP monitor is used for link detection, ARP replies are
validated for all slaves (arp_validate=3) and fail_over_mac is set to
active, two slaves of an active-backup bond may get stuck in a state
where both of them are active and pass packets that they receive to
the bond. This state makes IPv6 duplicate address detection fail. The
state is reached thus:
1. The current active slave goes down because the ARP target
is not reachable.
2. The current ARP slave is chosen and made active.
3. A new slave is enslaved. This new slave becomes the current active
slave and can reach the ARP target.
As a result, the current ARP slave stays active after the enslave
action has finished and the log is littered with "PROBE BAD" messages:
> bond0: PROBE: c_arp ens10 && cas ens11 BAD
The workaround is to remove the slave with "going back" status from
the bond and re-enslave it. This issue was encountered when DPDK PMD
interfaces were being enslaved to an active-backup bond.
I would be possible to fix the issue in bond_enslave() or
bond_change_active_slave() but the ARP monitor was fixed instead to
keep most of the actions changing the current ARP slave in the ARP
monitor code. The current ARP slave is set as inactive and backup
during the commit phase. A new state, BOND_LINK_FAIL, has been
introduced for slaves in the context of the ARP monitor. This allows
administrators to see how slaves are rotated for sending ARP requests
and attempts are made to find a new active slave.
Fixes: b2220cad58 ("bonding: refactor ARP active-backup monitor")
Signed-off-by: Jiri Wiesner <jwiesner@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8327070216 ]
When we tear down a network namespace, we unregister all
the netdevices within it. So we may queue a slave device
and a bonding device together in the same unregister queue.
If the only slave device is non-ethernet, it would
automatically unregister the bonding device as well. Thus,
we may end up unregistering the bonding device twice.
Workaround this special case by checking reg_state.
Fixes: 9b5e383c11 ("net: Introduce unregister_netdevice_many()")
Reported-by: syzbot+af23e7f3e0a7e10c8b67@syzkaller.appspotmail.com
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ca0d9ac3f ]
Broadcast mode bonds transmit a copy of all traffic simultaneously out of
all interfaces, so the "speed" of the bond isn't really the aggregate of
all interfaces, but rather, the speed of the slowest active interface.
Also, the type of the speed field is u32, not unsigned long, so adjust
that accordingly, as required to make min() function here without
complaining about mismatching types.
Fixes: bb5b052f75 ("bond: add support to read speed and duplex via ethtool")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c75d1d5248 ]
Very similar to commit 544f287b84
("bonding: check error value of register_netdevice() immediately"),
we should immediately check the return value of register_netdevice()
before doing anything else.
Fixes: 005db31d5f ("bonding: set carrier off for devices created through netlink")
Reported-and-tested-by: syzbot+bbc3a11c4da63c1b74d6@syzkaller.appspotmail.com
Cc: Beniamino Galvani <bgalvani@redhat.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a068aab422 upstream.
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object. Previous
commit "b8eb718348b8" fixed a similar problem.
Fixes: 07699f9a7c ("bonding: add sysfs /slave dir for bond slave devices.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38f88c4540 ]
syzbot managed to send an IPX packet through bond_alb_xmit()
and af_packet and triggered a use-after-free.
First, bond_alb_xmit() was using ipx_hdr() helper to reach
the IPX header, but ipx_hdr() was using the transport offset
instead of the network offset. In the particular syzbot
report transport offset was 0xFFFF
This patch removes ipx_hdr() since it was only (mis)used from bonding.
Then we need to make sure IPv4/IPv6/IPX headers are pulled
in skb->head before dereferencing anything.
BUG: KASAN: use-after-free in bond_alb_xmit+0x153a/0x1590 drivers/net/bonding/bond_alb.c:1452
Read of size 2 at addr ffff8801ce56dfff by task syz-executor.2/18108
(if (ipx_hdr(skb)->ipx_checksum != IPX_NO_CHECKSUM) ...)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
[<ffffffff8441fc42>] __dump_stack lib/dump_stack.c:17 [inline]
[<ffffffff8441fc42>] dump_stack+0x14d/0x20b lib/dump_stack.c:53
[<ffffffff81a7dec4>] print_address_description+0x6f/0x20b mm/kasan/report.c:282
[<ffffffff81a7e0ec>] kasan_report_error mm/kasan/report.c:380 [inline]
[<ffffffff81a7e0ec>] kasan_report mm/kasan/report.c:438 [inline]
[<ffffffff81a7e0ec>] kasan_report.cold+0x8c/0x2a0 mm/kasan/report.c:422
[<ffffffff81a7dc4f>] __asan_report_load_n_noabort+0xf/0x20 mm/kasan/report.c:469
[<ffffffff82c8c00a>] bond_alb_xmit+0x153a/0x1590 drivers/net/bonding/bond_alb.c:1452
[<ffffffff82c60c74>] __bond_start_xmit drivers/net/bonding/bond_main.c:4199 [inline]
[<ffffffff82c60c74>] bond_start_xmit+0x4f4/0x1570 drivers/net/bonding/bond_main.c:4224
[<ffffffff83baa558>] __netdev_start_xmit include/linux/netdevice.h:4525 [inline]
[<ffffffff83baa558>] netdev_start_xmit include/linux/netdevice.h:4539 [inline]
[<ffffffff83baa558>] xmit_one net/core/dev.c:3611 [inline]
[<ffffffff83baa558>] dev_hard_start_xmit+0x168/0x910 net/core/dev.c:3627
[<ffffffff83bacf35>] __dev_queue_xmit+0x1f55/0x33b0 net/core/dev.c:4238
[<ffffffff83bae3a8>] dev_queue_xmit+0x18/0x20 net/core/dev.c:4278
[<ffffffff84339189>] packet_snd net/packet/af_packet.c:3226 [inline]
[<ffffffff84339189>] packet_sendmsg+0x4919/0x70b0 net/packet/af_packet.c:3252
[<ffffffff83b1ac0c>] sock_sendmsg_nosec net/socket.c:673 [inline]
[<ffffffff83b1ac0c>] sock_sendmsg+0x12c/0x160 net/socket.c:684
[<ffffffff83b1f5a2>] __sys_sendto+0x262/0x380 net/socket.c:1996
[<ffffffff83b1f700>] SYSC_sendto net/socket.c:2008 [inline]
[<ffffffff83b1f700>] SyS_sendto+0x40/0x60 net/socket.c:2004
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d485ed88d ]
After the recent fix in commit 1899bb3251 ("bonding: fix state
transition issue in link monitoring"), the active-backup mode with
miimon initially come-up fine but after a link-failure, both members
transition into backup state.
Following steps to reproduce the scenario (eth1 and eth2 are the
slaves of the bond):
ip link set eth1 up
ip link set eth2 down
sleep 1
ip link set eth2 up
ip link set eth1 down
cat /sys/class/net/eth1/bonding_slave/state
cat /sys/class/net/eth2/bonding_slave/state
Fixes: 1899bb3251 ("bonding: fix state transition issue in link monitoring")
CC: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f394722fb0 ]
neigh_cleanup() has not been used for seven years, and was a wrong design.
Messing with shared pointer in bond_neigh_init() without proper
memory barriers would at least trigger syzbot complains eventually.
It is time to remove this stuff.
Fixes: b63b70d877 ("IPoIB: Use a private hash table for path lookup in xmit path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since de77ecd4ef ("bonding: improve link-status update in
mii-monitoring"), the bonding driver has utilized two separate variables
to indicate the next link state a particular slave should transition to.
Each is used to communicate to a different portion of the link state
change commit logic; one to the bond_miimon_commit function itself, and
another to the state transition logic.
Unfortunately, the two variables can become unsynchronized,
resulting in incorrect link state transitions within bonding. This can
cause slaves to become stuck in an incorrect link state until a
subsequent carrier state transition.
The issue occurs when a special case in bond_slave_netdev_event
sets slave->link directly to BOND_LINK_FAIL. On the next pass through
bond_miimon_inspect after the slave goes carrier up, the BOND_LINK_FAIL
case will set the proposed next state (link_new_state) to BOND_LINK_UP,
but the new_link to BOND_LINK_DOWN. The setting of the final link state
from new_link comes after that from link_new_state, and so the slave
will end up incorrectly in _DOWN state.
Resolve this by combining the two variables into one.
Reported-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Reported-by: Sha Zhang <zhangsha.zhang@huawei.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Fixes: de77ecd4ef ("bonding: improve link-status update in mii-monitoring")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes variables and callback these are related to the nested
device structure.
devices that can be nested have their own nest_level variable that
represents the depth of nested devices.
In the previous patch, new {lower/upper}_level variables are added and
they replace old private nest_level variable.
So, this patch removes all 'nest_level' variables.
In order to avoid lockdep warning, ->ndo_get_lock_subclass() was added
to get lockdep subclass value, which is actually lower nested depth value.
But now, they use the dynamic lockdep key to avoid lockdep warning instead
of the subclass.
So, this patch removes ->ndo_get_lock_subclass() callback.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All bonding device has same lockdep key and subclass is initialized with
nest_level.
But actual nest_level value can be changed when a lower device is attached.
And at this moment, the subclass should be updated but it seems to be
unsafe.
So this patch makes bonding use dynamic lockdep key instead of the
subclass.
Test commands:
ip link add bond0 type bond
for i in {1..5}
do
let A=$i-1
ip link add bond$i type bond
ip link set bond$i master bond$A
done
ip link set bond5 master bond0
Splat looks like:
[ 307.992912] WARNING: possible recursive locking detected
[ 307.993656] 5.4.0-rc3+ #96 Tainted: G W
[ 307.994367] --------------------------------------------
[ 307.995092] ip/761 is trying to acquire lock:
[ 307.995710] ffff8880513aac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 307.997045]
but task is already holding lock:
[ 307.997923] ffff88805fcbac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 307.999215]
other info that might help us debug this:
[ 308.000251] Possible unsafe locking scenario:
[ 308.001137] CPU0
[ 308.001533] ----
[ 308.001915] lock(&(&bond->stats_lock)->rlock#2/2);
[ 308.002609] lock(&(&bond->stats_lock)->rlock#2/2);
[ 308.003302]
*** DEADLOCK ***
[ 308.004310] May be due to missing lock nesting notation
[ 308.005319] 3 locks held by ip/761:
[ 308.005830] #0: ffffffff9fcc42b0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x466/0x8a0
[ 308.006894] #1: ffff88805fcbac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 308.008243] #2: ffffffff9f9219c0 (rcu_read_lock){....}, at: bond_get_stats+0x9f/0x500 [bonding]
[ 308.009422]
stack backtrace:
[ 308.010124] CPU: 0 PID: 761 Comm: ip Tainted: G W 5.4.0-rc3+ #96
[ 308.011097] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 308.012179] Call Trace:
[ 308.012601] dump_stack+0x7c/0xbb
[ 308.013089] __lock_acquire+0x269d/0x3de0
[ 308.013669] ? register_lock_class+0x14d0/0x14d0
[ 308.014318] lock_acquire+0x164/0x3b0
[ 308.014858] ? bond_get_stats+0xb8/0x500 [bonding]
[ 308.015520] _raw_spin_lock_nested+0x2e/0x60
[ 308.016129] ? bond_get_stats+0xb8/0x500 [bonding]
[ 308.017215] bond_get_stats+0xb8/0x500 [bonding]
[ 308.018454] ? bond_arp_rcv+0xf10/0xf10 [bonding]
[ 308.019710] ? rcu_read_lock_held+0x90/0xa0
[ 308.020605] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 308.021286] ? bond_get_stats+0x9f/0x500 [bonding]
[ 308.021953] dev_get_stats+0x1ec/0x270
[ 308.022508] bond_get_stats+0x1d1/0x500 [bonding]
Fixes: d3fff6c443 ("net: add netdev_lockdep_set_classes() helper")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debugfs core now will print a message if this function fails, so
don't duplicate that logic. Also, no need to change the code logic if
the call fails either, as no debugfs calls should interrupt normal
kernel code for any reason.
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As commit 30d8177e8a ("bonding: Always enable vlan tx offload")
said, we should always enable bonding's vlan tx offload, pass the
vlan packets to the slave devices with vlan tci, let them to handle
vlan implementation.
Now if encapsulation protocols like VXLAN is used, skb->encapsulation
may be set, then the packet is passed to vlan device which based on
bonding device. However in netif_skb_features(), the check of
hw_enc_features:
if (skb->encapsulation)
features &= dev->hw_enc_features;
clears NETIF_F_HW_VLAN_CTAG_TX/NETIF_F_HW_VLAN_STAG_TX. This results
in same issue in commit 30d8177e8a like this:
vlan_dev_hard_start_xmit
-->dev_queue_xmit
-->validate_xmit_skb
-->netif_skb_features //NETIF_F_HW_VLAN_CTAG_TX is cleared
-->validate_xmit_vlan
-->__vlan_hwaccel_push_inside //skb->tci is cleared
...
--> bond_start_xmit
--> bond_xmit_hash //BOND_XMIT_POLICY_ENCAP34
--> __skb_flow_dissect // nhoff point to IP header
--> case htons(ETH_P_8021Q)
// skb_vlan_tag_present is false, so
vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
//vlan point to ip header wrongly
Fixes: b2a103e6d0 ("bonding: convert to ndo_fix_features")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following scenario was encountered during testing of logical
partition mobility on pseries partitions with bonded ibmvnic
adapters in LACP mode.
1. Driver receives a signal that the device has been
swapped, and it needs to reset to initialize the new
device.
2. Driver reports loss of carrier and begins initialization.
3. Bonding driver receives NETDEV_CHANGE notifier and checks
the slave's current speed and duplex settings. Because these
are unknown at the time, the bond sets its link state to
BOND_LINK_FAIL and handles the speed update, clearing
AD_PORT_LACP_ENABLE.
4. Driver finishes recovery and reports that the carrier is on.
5. Bond receives a new notification and checks the speed again.
The speeds are valid but miimon has not altered the link
state yet. AD_PORT_LACP_ENABLE remains off.
Because the slave's link state is still BOND_LINK_FAIL,
no further port checks are made when it recovers. Though
the slave devices are operational and have valid speed
and duplex settings, the bond will not send LACPDU's. The
simplest fix I can see is to force another speed check
in bond_miimon_commit. This way the bond will update
AD_PORT_LACP_ENABLE if needed when transitioning from
BOND_LINK_FAIL to BOND_LINK_UP.
CC: Jarod Wilson <jarod@redhat.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_BOND_PEER_NOTIF_DELAY was set to the value of downdelay instead
of peer_notif_delay. After this change, the correct value is exported.
Fixes: 07a4ddec3c ("bonding: add an option to specify a delay between peer notifications")
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, gratuitous ARP/ND packets are sent every `miimon'
milliseconds. This commit allows a user to specify a custom delay
through a new option, `peer_notif_delay'.
Like for `updelay' and `downdelay', this delay should be a multiple of
`miimon' to avoid managing an additional work queue. The configuration
logic is copied from `updelay' and `downdelay'. However, the default
value cannot be set using a module parameter: Netlink or sysfs should
be used to configure this feature.
When setting `miimon' to 100 and `peer_notif_delay' to 500, we can
observe the 500 ms delay is respected:
20:30:19.354693 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:19.874892 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:20.394919 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:20.914963 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
In bond_mii_monitor(), I have tried to keep the lock logic readable.
The change is due to the fact we cannot rely on a notification to
lower the value of `bond->send_peer_notif' as `NETDEV_NOTIFY_PEERS' is
only triggered once every N times, while we need to decrement the
counter each time.
iproute2 also needs to be updated to be able to specify this new
attribute through `ip link'.
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_xmit_roundrobin() checks for IGMP packets but it parses
the IP header even before checking skb->protocol.
We should validate the IP header with pskb_may_pull() before
using iph->protocol.
Reported-and-tested-by: syzbot+e5be16aa39ad6e755391@syzkaller.appspotmail.com
Fixes: a2fd940f4c ("bonding: fix broken multicast with round-robin mode")
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
We build vlan on top of bonding interface, which vlan offload
is off, bond mode is 802.3ad (LACP) and xmit_hash_policy is
BOND_XMIT_POLICY_ENCAP34.
Because vlan tx offload is off, vlan tci is cleared and skb push
the vlan header in validate_xmit_vlan() while sending from vlan
devices. Then in bond_xmit_hash, __skb_flow_dissect() fails to
get information from protocol headers encapsulated within vlan,
because 'nhoff' is points to IP header, so bond hashing is based
on layer 2 info, which fails to distribute packets across slaves.
This patch always enable bonding's vlan tx offload, pass the vlan
packets to the slave devices with vlan tci, let them to handle
vlan implementation.
Fixes: 278339a42a ("bonding: propogate vlan_features to bonding master")
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of these printk instances benefit from having both master and slave
device information included, so convert to using a standardized macro
format and remove redundant information.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of these printk instances benefit from having both master and slave
device information included, so convert to using a standardized macro
format and remove redundant information.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of these printk instances benefit from having both master and slave
device information included, so convert to using a standardized macro
format and remove redundant information.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of these printk instances benefit from having both master and slave
device information included, so convert to using a standardized macro
format and remove redundant information.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing the bond name again to debug output when referencing slave is wrong.
We're trying to set the bond's MAC to that of the new_active slave, so adjust
the error message slightly and pass in the slave's name, not the bond's.
Then we're trying to set the MAC on the old active slave, but putting the
new active slave's name in the output. While we're at it, clarify the
error messages so you know which one actually triggered.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seeing bonding debug log data along the lines of "event: 5" is a bit spartan,
and often requires a lookup table if you don't remember what every event is.
Make use of netdev_cmd_to_name for an improved debugging experience, so for
the prior example, you'll see: "bond_netdev_event received NETDEV_REGISTER"
instead (both are prefixed with the device for which the event pertains).
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the bonding interface net device features,
the kernel code doesn't address the slaves' MPLS features
and doesn't inherit them.
Therefore, HW offloads that enhance performance such as
checksumming and TSO are disabled for MPLS tagged traffic
flowing via the bonding interface.
The patch add the inheritance of the MPLS features from the
slave devices with a similar logic to setting the bonding device's
VLAN and encapsulation features.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Pull networking fixes from David Miller:
1) Fix OOPS during nf_tables rule dump, from Florian Westphal.
2) Use after free in ip_vs_in, from Yue Haibing.
3) Fix various kTLS bugs (NULL deref during device removal resync,
netdev notification ignoring, etc.) From Jakub Kicinski.
4) Fix ipv6 redirects with VRF, from David Ahern.
5) Memory leak fix in igmpv3_del_delrec(), from Eric Dumazet.
6) Missing memory allocation failure check in ip6_ra_control(), from
Gen Zhang. And likewise fix ip_ra_control().
7) TX clean budget logic error in aquantia, from Igor Russkikh.
8) SKB leak in llc_build_and_send_ui_pkt(), from Eric Dumazet.
9) Double frees in mlx5, from Parav Pandit.
10) Fix lost MAC address in r8169 during PCI D3, from Heiner Kallweit.
11) Fix botched register access in mvpp2, from Antoine Tenart.
12) Use after free in napi_gro_frags(), from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (89 commits)
net: correct zerocopy refcnt with udp MSG_MORE
ethtool: Check for vlan etype or vlan tci when parsing flow_rule
net: don't clear sock->sk early to avoid trouble in strparser
net-gro: fix use-after-free read in napi_gro_frags()
net: dsa: tag_8021q: Create a stable binary format
net: dsa: tag_8021q: Change order of rx_vid setup
net: mvpp2: fix bad MVPP2_TXQ_SCHED_TOKEN_CNTR_REG queue value
ipv4: tcp_input: fix stack out of bounds when parsing TCP options.
mlxsw: spectrum: Prevent force of 56G
mlxsw: spectrum_acl: Avoid warning after identical rules insertion
net: dsa: mv88e6xxx: fix handling of upper half of STATS_TYPE_PORT
r8169: fix MAC address being lost in PCI D3
net: core: support XDP generic on stacked devices.
netvsc: unshare skb in VF rx handler
udp: Avoid post-GRO UDP checksum recalculation
net: phy: dp83867: Set up RGMII TX delay
net: phy: dp83867: do not call config_init twice
net: phy: dp83867: increase SGMII autoneg timer duration
net: phy: dp83867: fix speed 10 in sgmii mode
net: phy: marvell10g: report if the PHY fails to boot firmware
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once in a while, with just the right timing, 802.3ad slaves will fail to
properly initialize, winding up in a weird state, with a partner system
mac address of 00:00:00:00:00:00. This started happening after a fix to
properly track link_failure_count tracking, where an 802.3ad slave that
reported itself as link up in the miimon code, but wasn't able to get a
valid speed/duplex, started getting set to BOND_LINK_FAIL instead of
BOND_LINK_DOWN. That was the proper thing to do for the general "my link
went down" case, but has created a link initialization race that can put
the interface in this odd state.
The simple fix is to instead set the slave link to BOND_LINK_DOWN again,
if the link has never been up (last_link_up == 0), so the link state
doesn't bounce from BOND_LINK_DOWN to BOND_LINK_FAIL -- it hasn't failed
in this case, it simply hasn't been up yet, and this prevents the
unnecessary state change from DOWN to FAIL and getting stuck in an init
failure w/o a partner mac.
Fixes: ea53abfab9 ("bonding/802.3ad: fix link_failure_count tracking")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Tested-by: Heesoon Kim <Heesoon.Kim@stratus.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa the full gnu
general public license is included in this distribution in the file
called license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520075211.959886972@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses the full gnu
general public license is included in this distribution in the file
called license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.052102771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's currently a problem with toggling arp_validate on and off with an
active-backup bond. At the moment, you can start up a bond, like so:
modprobe bonding mode=1 arp_interval=100 arp_validate=0 arp_ip_targets=192.168.1.1
ip link set bond0 down
echo "ens4f0" > /sys/class/net/bond0/bonding/slaves
echo "ens4f1" > /sys/class/net/bond0/bonding/slaves
ip link set bond0 up
ip addr add 192.168.1.2/24 dev bond0
Pings to 192.168.1.1 work just fine. Now turn on arp_validate:
echo 1 > /sys/class/net/bond0/bonding/arp_validate
Pings to 192.168.1.1 continue to work just fine. Now when you go to turn
arp_validate off again, the link falls flat on it's face:
echo 0 > /sys/class/net/bond0/bonding/arp_validate
dmesg
...
[133191.911987] bond0: Setting arp_validate to none (0)
[133194.257793] bond0: bond_should_notify_peers: slave ens4f0
[133194.258031] bond0: link status definitely down for interface ens4f0, disabling it
[133194.259000] bond0: making interface ens4f1 the new active one
[133197.330130] bond0: link status definitely down for interface ens4f1, disabling it
[133197.331191] bond0: now running without any active interface!
The problem lies in bond_options.c, where passing in arp_validate=0
results in bond->recv_probe getting set to NULL. This flies directly in
the face of commit 3fe68df97c, which says we need to set recv_probe =
bond_arp_recv, even if we're not using arp_validate. Said commit fixed
this in bond_option_arp_interval_set, but missed that we can get to that
same state in bond_option_arp_validate_set as well.
One solution would be to universally set recv_probe = bond_arp_recv here
as well, but I don't think bond_option_arp_validate_set has any business
touching recv_probe at all, and that should be left to the arp_interval
code, so we can just make things much tidier here.
Fixes: 3fe68df97c ("bonding: always set recv_probe to bond_arp_rcv in arp monitor")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jamie Iles