[ Upstream commit 1f45dc2206 ]
Commit f9c6cea0b3 ("ibmvnic: Skip fatal error reset after passive init")
says "If the passive
CRQ initialization occurs before the FATAL reset task is processed,
the FATAL error reset task would try to access a CRQ message queue
that was freed, causing an oops. The problem may be most likely to
occur during DLPAR add vNIC with a non-default MTU, because the DLPAR
process will automatically issue a change MTU request.
Fix this by not processing fatal error reset if CRQ is passively
initialized after client-driven CRQ initialization fails."
Even with this commit, we still see similar kernel crashes. In order
to completely solve this problem, we'd better continue the fatal error
reset, capture the kernel crash, and try to fix it from that end.
Fixes: f9c6cea0b3 ("ibmvnic: Skip fatal error reset after passive init")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201219214034.21123-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 855a631a4c ]
Sometimes it takes longer than 5 seconds (watchdog timeout) to complete
failover, migration, and other resets. In stead of scheduling another
timeout reset, we wait for the current one to complete.
Suggested-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba246c1751 ]
TX completions received with an error return code are not
being processed properly. When an error code is seen, do not
proceed to the next completion before cleaning up the existing
entry's data structures.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b71ec95223 ]
Ensure that received Subordinate Command-Response Queue (SCRQ)
entries are properly read in order by the driver. These queues
are used in the ibmvnic device to process RX buffer and TX completion
descriptors. dma_rmb barriers have been added after checking for a
pending descriptor to ensure the correct descriptor entry is checked
and after reading the SCRQ descriptor to ensure the entire
descriptor is read before processing.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 98025bce3a ]
Commit 61d3e1d9bc ("ibmvnic: Remove netdev notify for failover resets")
excluded the failover case for notify call because it said
netdev_notify_peers() can cause network traffic to stall or halt.
Current testing does not show network traffic stall
or halt because of the notify call for failover event.
netdev_notify_peers may be used when a device wants to inform the
rest of the network about some sort of a reconfiguration
such as failover or migration.
It is unnecessary to call that in other events like
FATAL, NON_FATAL, CHANGE_PARAM, and TIMEOUT resets
since in those scenarios the hardware does not change.
If the driver must do a hard reset, it is necessary to notify peers.
Fixes: 61d3e1d9bc ("ibmvnic: Remove netdev notify for failover resets")
Suggested-by: Brian King <brking@linux.vnet.ibm.com>
Suggested-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d85049374 ]
Commit 5a18e1e0c1 introduced the 'failover_pending' state to track
the "failover pending window" - where we wait for the partner to become
ready (after a transport event) before actually attempting to failover.
i.e window is between following two events:
a. we get a transport event due to a FAILOVER
b. later, we get CRQ_INITIALIZED indicating the partner is
ready at which point we schedule a FAILOVER reset.
and ->failover_pending is true during this window.
If during this window, we attempt to open (or close) a device, we pretend
that the operation succeded and let the FAILOVER reset path complete the
operation.
This is fine, except if the transport event ("a" above) occurs during the
open and after open has already checked whether a failover is pending. If
that happens, we fail the open, which can cause the boot scripts to leave
the interface down requiring administrator to manually bring up the device.
This fix "extends" the failover pending window till we are _actually_
ready to perform the failover reset (i.e until after we get the RTNL
lock). Since open() holds the RTNL lock, we can be sure that we either
finish the open or if the open() fails due to the failover pending window,
we can again pretend that open is done and let the failover complete it.
We could try and block the open until failover is completed but a) that
could still timeout the application and b) Existing code "pretends" that
failover occurred "just after" open succeeded, so marks the open successful
and lets the failover complete the open. So, mark the open successful even
if the transport event occurs before we actually start the open.
Fixes: 5a18e1e0c1 ("ibmvnic: Fix failover case for non-redundant configuration")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Acked-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20201030170711.1562994-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8fc3672a8a ]
Jakub Kicinski brought up a concern in ibmvnic_set_mac().
ibmvnic_set_mac() does this:
ether_addr_copy(adapter->mac_addr, addr->sa_data);
if (adapter->state != VNIC_PROBED)
rc = __ibmvnic_set_mac(netdev, addr->sa_data);
So if state == VNIC_PROBED, the user can assign an invalid address to
adapter->mac_addr, and ibmvnic_set_mac() will still return 0.
The fix is to validate ethernet address at the beginning of
ibmvnic_set_mac(), and move the ether_addr_copy to
the case of "adapter->state != VNIC_PROBED".
Fixes: c26eba03e4 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201027220456.71450-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b9cd795b0e ]
Set up the speed according to crq->query_phys_parms.rsp.speed.
Fix IBMVNIC_10GBPS typo.
Fixes: f8d6ae0d27 ("ibmvnic: Report actual backing device speed and duplex values")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9b0e599b2 ]
After mac address change request completes successfully, the new mac
address need to be saved to adapter->mac_addr as well as
netdev->dev_addr. Otherwise, adapter->mac_addr still holds old
data.
Fixes: 62740e9788 ("net/ibmvnic: Update MAC address settings after adapter reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201020223919.46106-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ae4dff882 ]
Indentation and logic clearly show that this code is missing
parenthesis.
Fixes: 9f13457377 ("ibmvnic fix NULL tx_pools and rx_tools issue at do_reset")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f13457377 ]
At the time of do_rest, ibmvnic tries to re-initalize the tx_pools
and rx_pools to avoid re-allocating the long term buffer. However
there is a window inside do_reset that the tx_pools and
rx_pools were freed before re-initialized making it possible to deference
null pointers.
This patch fix this issue by always check the tx_pool
and rx_pool are not NULL after ibmvnic_login. If so, re-allocating
the pools. This will avoid getting into calling reset_tx/rx_pools with
NULL adapter tx_pools/rx_pools pointer. Also add null pointer check in
reset_tx_pools and reset_rx_pools to safe handle NULL pointer case.
Signed-off-by: Mingming Cao <mmc@linux.vnet.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27a2145d6f ]
RX queue IRQ mappings are disposed in both the TX IRQ and RX IRQ
error paths. Fix this and dispose of TX IRQ mappings correctly in
case of an error.
Fixes: ea22d51a78 ("ibmvnic: simplify and improve driver probe function")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b40eb7350 ]
Continue the reset path when partner adapter is not ready or H_CLOSED is
returned from reset crq. This patch allows the CRQ init to proceed to
establish a valid CRQ for traffic to flow after reset.
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dff515a3e7 ]
The VNIC driver's "login" command sequence is the final step
in the driver's initialization process with device firmware,
confirming the available device queue resources to be utilized
by the driver. Under high system load, firmware may not respond
to the request in a timely manner or may abort the request. In
such cases, the driver should reattempt the login command
sequence. In case of a device error, the number of retries
is bounded.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 784688993e ]
VNIC protocol version is reported in big-endian format, but it
is not byteswapped before logging. Fix that, and remove version
comparison as only one protocol version exists at this time.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9c6cea0b3 ]
During MTU change, the following events may happen.
Client-driven CRQ initialization fails due to partner’s CRQ closed,
causing client to enqueue a reset task for FATAL_ERROR. Then passive
(server-driven) CRQ initialization succeeds, causing client to
release CRQ and enqueue a reset task for failover. If the passive
CRQ initialization occurs before the FATAL reset task is processed,
the FATAL error reset task would try to access a CRQ message queue
that was freed, causing an oops. The problem may be most likely to
occur during DLPAR add vNIC with a non-default MTU, because the DLPAR
process will automatically issue a change MTU request.
Fix this by not processing fatal error reset if CRQ is passively
initialized after client-driven CRQ initialization fails.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 070eca955c ]
Fix multiple calls to init_completion for device completion
structures. Instead, initialize them during device probe and
reinitialize them later as needed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Reversion of commit 11d49ce9f7
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) leaves us
calling H_EOI even in XIVE mode. That will fail with H_FUNCTION
because H_EOI is not supported in that mode. That failure is
harmless. Ignore it so we can use common code for both XICS and
XIVE.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 11d49ce9f7
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) since that
has the unintended effect of changing the interrupt priority
and emits warning when running in legacy XICS mode.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pSeries machines on POWER9 processors can run with the XICS (legacy)
interrupt mode or with the XIVE exploitation interrupt mode. These
interrupt contollers have different interfaces for interrupt
management : XICS uses hcalls and XIVE loads and stores on a page.
H_EOI being a XICS interface the enable_scrq_irq() routine can fail
when the machine runs in XIVE mode.
Fix that by calling the EOI handler of the interrupt chip.
Fixes: f23e0643cd ("ibmvnic: Clear pending interrupt after device reset")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code allows more than one thread to run in reset. This can
corrupt struct adapter data. Check adapter->resetting before performing
a reset, if there is another reset running delay (100 msec) before trying
again.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5681e20b5 ("net/ibmnvic: Fix deadlock problem in reset")
made the change to hold the RTNL lock during a reset to avoid deadlock
but linkwatch_event is fired during the reset and needs the RTNL lock.
That keeps linkwatch_event process from proceeding until the reset
is complete. The reset process cannot tolerate the linkwatch_event
processing after reset completes, so release the RTNL lock during the
process to allow a chance for linkwatch_event to run during reset.
This does not guarantee that the linkwatch_event will be processed as
soon as link state changes, but is an improvement over the current code
where linkwatch_event processing is always delayed, which prevents
transmissions on the device from being deactivated leading transmit
watchdog timer to time-out.
Release the RTNL lock before link state change and re-acquire after
the link state change to allow linkwatch_event to grab the RTNL lock
and run during the reset.
Fixes: a5681e20b5 ("net/ibmnvic: Fix deadlock problem in reset")
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit 0655f9943d ("net/ibmvnic: Update carrier state after link
state change") we are now able to detect when the carrier is properly
present in the device, so only report an unexpected unknown speed when it
is properly detected. Unknown speed is expected to be seen by the device
in case the backing device has no link detected.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Commit 1c2977c094 ("net/ibmvnic: free reset work of removed device from queue")
adds a } without corresponding { causing build break.
Fixes: 1c2977c094 ("net/ibmvnic: free reset work of removed device from queue")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Reviewed-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 36f1031c51 ("ibmvnic: Do not process reset during or after
device removal") made the change to exit reset if the driver has been
removed, but does not free reset work items of the adapter from queue.
Ensure all reset work items are freed when breaking out of the loop early.
Fixes: 36f1031c51 ("ibmnvic: Do not process reset during or after device removal”)
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the ibmvnic driver will not schedule device resets
if the device is being removed, but does not check the device
state before the reset is actually processed. This leads to a race
where a reset is scheduled with a valid device state but is
processed after the driver has been removed, resulting in an oops.
Fix this by checking the device state before processing a queued
reset event.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to wait until a completion is received to unmap
TX descriptor buffers that have been passed to the hypervisor.
Instead unmap it when the hypervisor call has completed. This patch
avoids the possibility that a buffer will not be unmapped because
a TX completion is lost or mishandled.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Devesh K. Singh <devesh_singh@in.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return values for these memory allocations are unchecked,
which may cause an oops if the driver does not handle them after
a failure. Fix by checking the function's return code.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was observed that multicast packets were no longer received after
a device reset. The fix is to resend the current multicast list to
the backing device after recovery.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check driver state before halting it during a reset. If the driver is
not running, do nothing. Otherwise, a request to deactivate a down link
can cause an error and the reset will fail.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091650.663497195@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only set the device carrier state to on after receiving an up link
state indication from the underlying adapter. Likewise, if a down
link indication is receieved, update the carrier state accordingly.
This fix ensures that accurate carrier state is reported by the driver
following a link state update by the underlying adapter.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was discovered in testing that the underlying hardware MAC
address will revert to initial settings following a device reset,
but the driver fails to resend the current OS MAC settings. This
oversight can result in dropped packets should the scenario occur.
Fix this by informing hardware of current MAC address settings
following any adapter initialization or resets.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver currently uses the same fixed name when using
request_irq, this makes it hard to parse when multiple VNIC devices are
available at the same time. This patch adds the unit_address as the device
identification along with an id for each queue.
The original idea was to use the interface name as an identifier, but it
is not feasible given these requests happen at adapter probe, and at this
point netdev is not yet registered so it doesn't have the proper name
assigned to it.
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While determining offload capabilities of backing hardware during
a device reset, the driver is clobbering current feature settings.
Update hw_features on reset instead of features unless a feature
is enabled that is no longer supported on the current backing device.
Also enable features that were not supported prior to the reset but
were previously enabled or requested by the user.
This can occur if the reset is the result of a carrier change, such
as a device failover or partition migration.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Generic Receive Offload in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/ibm/ibmvnic.c: In function '__ibmvnic_reset':
drivers/net/ethernet/ibm/ibmvnic.c:1971:21: warning: variable 'netdev' set but not used [-Wunused-but-set-variable]
It's never used since introduction in
commit ed651a1087 ("ibmvnic: Updated reset handling")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver currently reports a fixed value for both speed and
duplex settings regardless of the actual backing device that is being
used. By adding support to the QUERY_PHYS_PARMS command defined by the
PAPR+ we can query the current physical port state and report the proper
values for these feilds.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was checking for non-NULL address.
- adapter->napi[i]
This is pointless as these will be always non-NULL, since the
'dapter->napi' is allocated in init_napi().
It is safe to get rid of useless checks for addresses to fix the
coccinelle warning:
>>drivers/net/ethernet/ibm/ibmvnic.c: test of a variable/field address
Since such statements always return true, they are redundant.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Thomas Falcon <tlfalcon@linux.ibm.com>
CC: John Allen <jallen@linux.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linuxppc-dev@lists.ozlabs.org
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Lijun Pan