[ Upstream commit 4f374d2c43 ]
The packet coalescing interrupt threshold has separated registers
for different aggregated/cpu (sw-thread). The required value should
be loaded for every thread but not only for 1 current cpu.
Fixes: 213f428f50 ("net: mvpp2: add support for TX interrupts and RX queue distribution modes")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608748521-11033-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2575bc1aa9 ]
During GoP port 2 Networking Complex Control mode of operation configurations,
also GoP port 3 mode of operation was wrongly set.
Patch removes these configurations.
Fixes: f84bf386f3 ("net: mvpp2: initialize the GoP")
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608462149-1702-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fec6079b2e ]
Current PPPoE+IPv6 entry is jumping to 'next-hdr'
field and not to 'DIP' field as done for IPv4.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Reported-by: Liron Himi <lironh@marvell.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608230266-22111-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f48fab62b ]
Issue:
Flow control frame used to pause GoP(MAC) was delivered to the CPU
and created a load on the CPU. Since XOFF/XON frames are used only
by MAC, these frames should be dropped inside MAC.
Fix:
According to 802.3-2012 - IEEE Standard for Ethernet pause frame
has unique destination MAC address 01-80-C2-00-00-01.
Add TCAM parser entry to track and drop pause frames by destination MAC.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608229817-21951-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c2b49eb96 ]
Add a helper to convert the struct phylink_config pointer passed in
from phylink to the drivers internal struct mvpp2_port.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82a10dc7f0 ]
Fix to return negative error code -ENOENT from invalid configuration
error handling case instead of 0, as done elsewhere in this function.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201203141806.37966-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc970925fe ]
The ethtool rx and tx queue statistics are reporting wrong values.
Fix reading out the correct ones.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 807eaf9968 ]
The remove function does not destroy all
BM Pools when per cpu pool is active.
When reloading the mvpp2 as a module the BM Pools
are still active in hardware and due to the bug
have twice the size now old + new.
This eventually leads to a kernel crash.
v2:
* add Fixes tag
Fixes: 7d04b0b13b ("mvpp2: percpu buffers")
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3138a07ce2 ]
When rxhash is enabled on any ethernet port except the first in each CP
block, traffic flow is prevented. The analysis is below:
I've been investigating this afternoon, and what I've found, comparing
a kernel without 895586d5dc and with 895586d5dc applied is:
- The table programmed into the hardware via mvpp22_rss_fill_table()
appears to be identical with or without the commit.
- When rxhash is enabled on eth2, mvpp2_rss_port_c2_enable() reports
that c2.attr[0] and c2.attr[2] are written back containing:
- with 895586d5dc, failing: 00200000 40000000
- without 895586d5dc, working: 04000000 40000000
- When disabling rxhash, c2.attr[0] and c2.attr[2] are written back as:
04000000 00000000
The second value represents the MVPP22_CLS_C2_ATTR2_RSS_EN bit, the
first value is the queue number, which comprises two fields. The high
5 bits are 24:29 and the low three are 21:23 inclusive. This comes
from:
c2.attr[0] = MVPP22_CLS_C2_ATTR0_QHIGH(qh) |
MVPP22_CLS_C2_ATTR0_QLOW(ql);
So, the working case gives eth2 a queue id of 4.0, or 32 as per
port->first_rxq, and the non-working case a queue id of 0.1, or 1.
The allocation of queue IDs seems to be in mvpp2_port_probe():
if (priv->hw_version == MVPP21)
port->first_rxq = port->id * port->nrxqs;
else
port->first_rxq = port->id * priv->max_port_rxqs;
Where:
if (priv->hw_version == MVPP21)
priv->max_port_rxqs = 8;
else
priv->max_port_rxqs = 32;
Making the port 0 (eth0 / eth1) have port->first_rxq = 0, and port 1
(eth2) be 32. It seems the idea is that the first 32 queues belong to
port 0, the second 32 queues belong to port 1, etc.
mvpp2_rss_port_c2_enable() gets the queue number from it's parameter,
'ctx', which comes from mvpp22_rss_ctx(port, 0). This returns
port->rss_ctx[0].
mvpp22_rss_context_create() is responsible for allocating that, which
it does by looking for an unallocated priv->rss_tables[] pointer. This
table is shared amongst all ports on the CP silicon.
When we write the tables in mvpp22_rss_fill_table(), the RSS table
entry is defined by:
u32 sel = MVPP22_RSS_INDEX_TABLE(rss_ctx) |
MVPP22_RSS_INDEX_TABLE_ENTRY(i);
where rss_ctx is the context ID (queue number) and i is the index in
the table.
If we look at what is written:
- The first table to be written has "sel" values of 00000000..0000001f,
containing values 0..3. This appears to be for eth1. This is table 0,
RX queue number 0.
- The second table has "sel" values of 00000100..0000011f, and appears
to be for eth2. These contain values 0x20..0x23. This is table 1,
RX queue number 0.
- The third table has "sel" values of 00000200..0000021f, and appears
to be for eth3. These contain values 0x40..0x43. This is table 2,
RX queue number 0.
How do queue numbers translate to the RSS table? There is another
table - the RXQ2RSS table, indexed by the MVPP22_RSS_INDEX_QUEUE field
of MVPP22_RSS_INDEX and accessed through the MVPP22_RXQ2RSS_TABLE
register. Before 895586d5dc, it was:
mvpp2_write(priv, MVPP22_RSS_INDEX,
MVPP22_RSS_INDEX_QUEUE(port->first_rxq));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE,
MVPP22_RSS_TABLE_POINTER(port->id));
and after:
mvpp2_write(priv, MVPP22_RSS_INDEX, MVPP22_RSS_INDEX_QUEUE(ctx));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE, MVPP22_RSS_TABLE_POINTER(ctx));
Before the commit, for eth2, that would've contained '32' for the
index and '1' for the table pointer - mapping queue 32 to table 1.
Remember that this is queue-high.queue-low of 4.0.
After the commit, we appear to map queue 1 to table 1. That again
looks fine on the face of it.
Section 9.3.1 of the A8040 manual seems indicate the reason that the
queue number is separated. queue-low seems to always come from the
classifier, whereas queue-high can be from the ingress physical port
number or the classifier depending on the MVPP2_CLS_SWFWD_PCTRL_REG.
We set the port bit in MVPP2_CLS_SWFWD_PCTRL_REG, meaning that queue-high
comes from the MVPP2_CLS_SWFWD_P2HQ_REG() register... and this seems to
be where our bug comes from.
mvpp2_cls_oversize_rxq_set() sets this up as:
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_P2HQ_REG(port->id),
(port->first_rxq >> MVPP2_CLS_OVERSIZE_RXQ_LOW_BITS));
val = mvpp2_read(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG);
val |= MVPP2_CLS_SWFWD_PCTRL_MASK(port->id);
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG, val);
Setting the MVPP2_CLS_SWFWD_PCTRL_MASK bit means that the queue-high
for eth2 is _always_ 4, so only queues 32 through 39 inclusive are
available to eth2. Yet, we're trying to tell the classifier to set
queue-high, which will be ignored, to zero. Hence, the queue-high
field (MVPP22_CLS_C2_ATTR0_QHIGH()) from the classifier will be
ignored.
This means we end up directing traffic from eth2 not to queue 1, but
to queue 33, and then we tell it to look up queue 33 in the RSS table.
However, RSS table has not been programmed for queue 33, and so it ends
up (presumably) dropping the packets.
It seems that mvpp22_rss_context_create() doesn't take account of the
fact that the upper 5 bits of the queue ID can't actually be changed
due to the settings in mvpp2_cls_oversize_rxq_set(), _or_ it seems that
mvpp2_cls_oversize_rxq_set() has been missed in this commit. Either
way, these two functions mutually disagree with what queue number
should be used.
Looking deeper into what mvpp2_cls_oversize_rxq_set() and the MTU
validation is doing, it seems that MVPP2_CLS_SWFWD_P2HQ_REG() is used
for over-sized packets attempting to egress through this port. With
the classifier having had RSS enabled and directing eth2 traffic to
queue 1, we may still have packets appearing on queue 32 for this port.
However, the only way we may end up with over-sized packets attempting
to egress through eth2 - is if the A8040 forwards frames between its
ports. From what I can see, we don't support that feature, and the
kernel restricts the egress packet size to the MTU. In any case, if we
were to attempt to transmit an oversized packet, we have no support in
the kernel to deal with that appearing in the port's receive queue.
So, this patch attempts to solve the issue by clearing the
MVPP2_CLS_SWFWD_PCTRL_MASK() bit, allowing MVPP22_CLS_C2_ATTR0_QHIGH()
from the classifier to define the queue-high field of the queue number.
My testing seems to confirm my findings above - clearing this bit
means that if I enable rxhash on eth2, the interface can then pass
traffic, as we are now directing traffic to RX queue 1 rather than
queue 33. Traffic still seems to work with rxhash off as well.
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Fixes: 895586d5dc ("net: mvpp2: cls: Use RSS contexts to handle RSS tables")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 722c0f00d4 ]
The "info->fs.location" is a u32 that comes from the user via the
ethtool_set_rxnfc() function. We need to check for invalid values to
prevent a buffer overflow.
I copy and pasted this check from the mvpp2_ethtool_cls_rule_ins()
function.
Fixes: 90b509b39a ("net: mvpp2: cls: Add Classification offload support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 39bd16df7c ]
The "rss_context" variable comes from the user via ethtool_get_rxfh().
It can be any u32 value except zero. Eventually it gets passed to
mvpp22_rss_ctx() and if it is over MVPP22_N_RSS_TABLES (8) then it
results in an array overflow.
Fixes: 895586d5dc ("net: mvpp2: cls: Use RSS contexts to handle RSS tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3f2364ea1 ]
phylink requires the MAC to report when its link status changes when
operating in inband modes. Failure to report link status changes
means that phylink has no idea when the link events happen, which
results in either the network interface's carrier remaining up or
remaining permanently down.
For example, with a fiber module, if the interface is brought up and
link is initially established, taking the link down at the far end
will cut the optical power. The SFP module's LOS asserts, we
deactivate the link, and the network interface reports no carrier.
When the far end is brought back up, the SFP module's LOS deasserts,
but the MAC may be slower to establish link. If this happens (which
in my tests is a certainty) then phylink never hears that the MAC
has established link with the far end, and the network interface is
stuck reporting no carrier. This means the interface is
non-functional.
Avoiding the link interrupt when we have phylink is basically not
an option, so remove the !port->phylink from the test.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every mvpp2 unit can use up to 8 buffers mapped by the BM (the HW buffer
manager). The HW will place the frames in the buffer pool depending on the
frame size: short (< 128 bytes), long (< 1664) or jumbo (up to 9856).
As any unit can have up to 4 ports, the driver allocates only 2 pools,
one for small and one long frames, and share them between ports.
When the first port MTU is set higher than 1664 bytes, a third pool is
allocated for jumbo frames.
This shared allocation makes impossible to use percpu allocators,
and creates contention between HW queues.
If possible, i.e. if the number of possible CPU are less than 8 and jumbo
frames are not used, switch to a new scheme: allocate 8 per-cpu pools for
short and long frames and bind every pool to an RXQ.
When the first port MTU is set higher than 1664 bytes, the allocation
scheme is reverted to the old behaviour (3 shared pools), and when all
ports MTU are lowered, the per-cpu buffers are allocated again.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor mvpp2_bm_pool_create(), mvpp2_bm_pool_destroy() and
mvpp2_bm_pools_init() so that they accept a struct device instead
of a struct platform_device, as they just need platform_device->dev.
Removing such dependency makes the BM code more reusable in context
where we don't have a pointer to the platform_device.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_done_tasklet tasklet is used in invoke the hrtimer
(mvpp2_hr_timer_cb) in softirq context. This can be also achieved without
the tasklet but with HRTIMER_MODE_SOFT as hrtimer mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Nathan Huckleberry <nhuck@google.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can only offload checksum calculation on first port due to
the Tx FIFO size limitation, and has a maximum L3 offset of 128 bytes.
Document this in a comment and move duplicated code in a function.
Fixes: 576193f2d5 ("net: mvpp2: jumbo frames support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU change code can call napi_disable() with the device already down,
leading to a deadlock. Also, lot of code is duplicated unnecessarily.
Rework mvpp2_change_mtu() to avoid the deadlock and remove duplicated code.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2's XLGMAC can wait for 3 idle frames before triggering a link up
event. This can cause the link to be stuck low when there's traffic on
the interface, so disable this feature.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users can specify classification actions based on the 'ether' flow type.
In that case, this will apply to all ethernet traffic, superseeding
flows such as 'udp4' or 'tcp6'.
Add support for this flow type in the PPv2 classifier, by mapping the
ETHER_FLOW value to the corresponding entries in the classifier.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing check to detect flow types that we don't support, so that
user can be informed of this.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Header Parser allows identifying various fields in the packet
headers, used for various kind of filtering and classification
steps.
This is a re-entrant process, where the offset in the packet header
depends on the previous lookup results. This offset is represented in
the SRAM results of the TCAM, as a shift to be operated.
This shift can be negative in some cases, such as in IPv6 parsing.
This commit prevents overriding the sign bit when setting the shift
value, which could cause instabilities when parsing IPv6 flows.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Suggested-by: Alan Winkowski <walan@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was an unused variable 'mvpp2_dbgfs_prs_pmap_fops'
Added a usage consistent with other fops to dump pmap
to userspace.
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/529
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows using the vlan Id and priority as parts of the key
for classification offload. These fields are extracted from the
outermost tag, if multiple tags are present.
Vlan Id and priority are considered as 2 different fields by the
classifier, however the fields are both appended in the Header Extracted
Key in the same layout as they are found in the tags. This means that
when steering only based on the prio, a 16-bit slot is still taken in
the HEK.
The classifier doesn't allow extracting the DEI bit from the tag, so we
explicitly prevent user from using this bit in the key.
This commit adds the vlan priotity as a compatible HEK field for
tagged traffic, meaning that we limit the possibility of extracting this
field only to the flows that contain tagged traffic.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The C2 TCAM used for classification uses a key (Header Extracted Key)
built by concatenating several fields extracted from the packet header.
After a lot of trial-and-error and some guess work, it seems the HEK is
right justified, with the first fields being stored in the MSB, then
concatenated up until the LSB.
Until now, this doesn't cause any issue since all HEK fields we use are
full bytes. However this is an issue for the upcoming VLAN id and pri
extraction, which aren't full bytes.
Rework the way we built that TCAM key, by changing the order in which we
append the fields.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way we currently handle classification offload and RSS is by having
dedicated lookup sequences in the flow table, each being selected
depending on several fields being present in the packet header.
We need to make sure the classification operation we want to perform can
be done in each flow we want to insert it into. As an example,
classifying on VLAN tag can only be done on flows used for tagged
traffic.
This commit makes sure we don't insert rules in flows we aren't
compatible with.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing a TCAM lookup in the C2 engine, it's possible that
multiple entries match the packet. To make sure the correct entry match
when performing a lookup, the Flow Table can set a lookup type, which
will be used in the TCAM lookup, thus preventing such false-positives.
We need to make sure the RSS match doesn't interfere with other
classification lookups, hence we use a dedicated lookup_type for it.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing all VID filters, the mvpp2_prs_vid_entry_remove would be
called with the TCAM id incorrectly used as a VID, causing the wrong
TCAM entries to be invalidated.
Fix this by directly invalidating entries in the VID range.
Fixes: 56beda3db6 ("net: mvpp2: Add hardware offloading for VLAN filtering")
Suggested-by: Yuri Chipchev <yuric@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VID filtering is implemented in the Header Parser, with one range of 11
vids being assigned for each no-loopback port.
Make sure we use the per-port range when looking for existing entries in
the Parser.
Since we used a global range instead of a per-port one, this causes VIDs
to be removed from the whitelist from all ports of the same PPv2
instance.
Fixes: 56beda3db6 ("net: mvpp2: Add hardware offloading for VLAN filtering")
Suggested-by: Yuri Chipchev <yuric@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Besides the MIB counters, some other useful counters can be exposed to
the user. This commit adds support for :
- Per-port counters, that indicate FIFO drops and classifier drops,
- Per-rxq counters,
- Per-txq counters
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we'll be adding support for other kind of internal counters, make
clear that the currently supported counters are the MIB counters.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When first configuring a port on PPv2, we want to clear the internal
counters so that we don't get values from previous boot stages.
However, we can't really clear these counters when resetting the MAC,
since there are valid reasons to do so while the port is being used,
such as when reconfiguring the interface mode with the PHY.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a safe strscpy call to copy the ethtool stat strings into the
relevant buffers, instead of a memcpy that will be accessing
out-of-bound data.
Fixes: 118d6298f6 ("net: mvpp2: add ethtool GOP statistics")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
MVPP2_TXQ_SCHED_TOKEN_CNTR_REG() expects the logical queue id but
the current code is passing the global tx queue offset, so it ends
up writing to unknown registers (between 0x8280 and 0x82fc, which
seemed to be unused by the hardware). This fixes the issue by using
the logical queue id instead.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix smatch warning:
drivers/net/ethernet/marvell/mvpp2/mvpp2_cls.c:1236
mvpp2_ethtool_cls_rule_ins() warn: unsigned 'info->fs.location' is never less than zero.
'info->fs.location' is u32 type, never less than zero.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.
A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.
At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.
This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we don't use an out-of-bound index for the per-port RSS
context array.
As of today, the global context creation in mvpp22_rss_context_create
will prevent us from reaching this case, but we should still make sure
we are using a sane value anyway.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When steering to an RXQ, we can perform an extra RSS step to assign a
queue from an RSS table.
This is done by setting the RSS_EN attribute in the C2 engine. In that
case, the RXQ that is assigned is the global RSS context id, that is
then translated to an RSS table using the RXQ2RSS table.
An example using ethtool to steer to RXQ 2 and 3 would be :
ethtool -X eth0 weight 0 0 1 1 context new
(This would print the allocated context id, let's say it's 1)
ethtool -N eth0 flow-type udp4 dst-port 1234 context 1 loc 0
The hash parameters are the ones that are globally configured for RSS :
ethtool -N eth0 rx-flow-hash udp4 sdfn
When an RSS context is removed while there are active classification
rules using this context, these rules are removed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool_rx_flow_rule_create takes into parameter the ethtool flow spec,
which doesn't contain the rss context id. We therefore need to extract
it ourself before parsing the ethtool rule.
The FLOW_RSS flag is only set in info->fs.flow_type, and not
info->flow_type.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 controller has 8 RSS tables that are shared across all ports on
a given PPv2 instance. The previous implementation allocated one table
per port, leaving others unused.
By using RSS contexts, we can make use of multiple RSS tables per
port, one being the default table (always id 0), the other ones being
used as destinations for flow steering, in the same way as rx rings.
This commit introduces RSS contexts management in the PPv2 driver. We
always reserve one table per port, allocated when the port is probed.
The global table list is stored in the struct mvpp2, as it's a global
resource. Each port then maintains a list of indices in that global
table, that way each port can have it's own numbering scheme starting
from 0.
One limitation that seems unavoidable is that the hashing parameters are
shared across all RSS contexts for a given port. Hashing parameters for
ctx 0 will be applied to all contexts.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The C2 TCAM has internal FIFOs that are only useful for the built-in
self-tests. Disable these FIFOS at init, as recommended in the
functionnal specs.
Suggested-by: Alan Winkowski <walan@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Chulski