[ Upstream commit 555a893303 ]
in recent kernel versions there are warnings about incorrect MTU size
like these:
eth0: mtu greater than device maximum
mtk_soc_eth 1b100000.ethernet eth0: error -22 setting MTU to include DSA overhead
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Fixes: 72579e14a1 ("net: dsa: don't fail to probe if we couldn't set the MTU")
Fixes: 7a4c53bee3 ("net: report invalid mtu value via netlink extack")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 19016d93bf ]
Modify mtk_gmac0_rgmii_adjust() so it can always be called.
mtk_gmac0_rgmii_adjust() sets-up the TRGMII clocks.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-By: David Woodhouse <dwmw2@infradead.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5d7553829 ]
Moving mt7623 logic out off mt7530, is required to make hardware setting
consistent after we introduce phylink to mtk driver.
Fixes: b8fc9f3082 ("net: ethernet: mediatek: Add basic PHYLINK support")
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the original design, mtk_phy_connect function will set ge_mode=1
if phy-mode is GMII(PHY_INTERFACE_MODE_GMII) and then set the correct
ge_mode to ETHSYS_SYSCFG0 register. This logic was broken after apply
mediatek PHYLINK patch(Fixes tag), the new mtk_mac_config function will
not set ge_mode=1 for GMII mode hence the final ETHSYS_SYSCFG0 setting
will be incorrect for mt7629 GMII mode. This patch add the missing logic
back to fix it.
Fixes: b8fc9f3082 ("net: ethernet: mediatek: Add basic PHYLINK support")
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c: In function mtk_handle_irq:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:1951:6: warning: variable status set but not used [-Wunused-but-set-variable]
Fixes: 296c912075 ("net: ethernet: mediatek: Add MT7628/88 SoC support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Re-add SGMII support but now with PHYLINK API support
So the SGMII changes are more clear
* Move SGMII block setup from mtk_gmac_sgmii_path_setup() to
mtk_mac_config()
* Merge mtk_setup_hw_path() into mtk_mac_config()
* Remove mediatek,physpeed property, fixed-link supports now any speed so
speed = <2500>; is now valid with PHYLINK
* Demagic SGMII register values
* Use phylink state to setup fixed-link mode
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This convert the basics to PHYLINK API.
SGMII support is not in this patch.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ee641b0cdb.
Actually it is not clear whether this register read is not
needed for it's HW side effects or not.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c: In function mtk_handle_irq:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:1951:6: warning: variable status set but not used [-Wunused-but-set-variable]
Fixes: 296c912075 ("net: ethernet: mediatek: Add MT7628/88 SoC support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the MediaTek MT7628/88 SoCs to the common
MediaTek ethernet driver. Some minor changes are needed for this and
a bigger change, as the MT7628 does not support QDMA (only PDMA).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: René van Dorst <opensource@vdorst.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the NEXT_RX_DESP_IDX macro to NEXT_DESP_IDX, so that it better
can be used for TX ops as well. This will be used in the upcoming
MT7628/88 support (same functionality for RX and TX in this macro).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: René van Dorst <opensource@vdorst.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all QDMA registers are named "MTK_QDMA_foo" in this driver
with one exception: MTK_QMTK_INT_STATUS. This patch renames
MTK_QMTK_INT_STATUS to MTK_QDMA_INT_STATUS so that all macros follow
this rule.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: René van Dorst <opensource@vdorst.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole block is protected by "if NET_VENDOR_MEDIATEK", so there is
no need for individual driver config symbols to duplicate this
dependency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
I missed a few places. One is in some ifdeffed code which will probably
never be re-enabled; the others are in drivers which can't currently be
compiled on x86.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a goto from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the goto.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both MTK_TRGMII_MT7621_CLK and MTK_PATH_BIT are defined as bit 10.
This can causes issues on non-MT7621 devices which has the
MTK_PATH_BIT(MTK_ETH_PATH_GMAC1_RGMII) and MTK_TRGMII capability set.
The wrong TRGMII setup code can be executed. The current wrongly executed
code doesn’t do any harm on MT7623 and the TRGMII setup for the MT7623
SOC side is done in MT7530 driver So it wasn’t noticed in the test.
Move all capability bits in one enum so that they are all unique and easy
to expand in the future.
Because mtk_eth_path enum is merged in to mkt_eth_capabilities, the
variable path value is no longer between 0 to number of paths,
mtk_eth_path_name can’t be used anymore in this form. Convert the
mtk_eth_path_name array to a function to lookup the pathname.
The old code walked thru the mtk_eth_path enum, which is also merged
with mkt_eth_capabilities. Expand array mtk_eth_muxc so it can store the
name and capability bit of the mux. Convert the code so it can walk thru
the mtk_eth_muxc array.
Fixes: 8efaa653a8 ("net: ethernet: mediatek: Add MT7621 TRGMII mode support")
Signed-off-by: René van Dorst <opensource@vdorst.com>
v1->v2:
- Move all capability bits in one enum, suggested by Willem de Bruijn
- Convert the mtk_eth_path_name array to a function to lookup the pathname
- Expand array mtk_eth_muxc so it can also store the name and capability
bit of the mux
- Updated commit message
Signed-off-by: David S. Miller <davem@davemloft.net>
No reason to error out on a MT7621 device with DDR2 memory when non
TRGMII mode is selected.
Only MT7621 DDR2 clock setup is not supported for TRGMII mode.
But non TRGMII mode doesn't need any special clock setup.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7621 SOC also supports TRGMII.
TRGMII speed is 1200MBit.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPuGTg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykBvQCg2SG+HmDH+tlwKLT/q7jZcLMPQigAoMpt9Uuy
sxVEiFZo8ZU9v1IoRb1I
=qU++
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build errors in Mediatek mtk_eth_soc driver.
It looks like these 3 source files were meant to be linked together
since 2 of them are library-like functions,
but they are currently being built as 3 loadable modules.
Fixes these build errors:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/mediatek/mtk_eth_path.o
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/mediatek/mtk_sgmii.o
ERROR: "mtk_sgmii_init" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined!
ERROR: "mtk_setup_hw_path" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined!
ERROR: "mtk_sgmii_setup_mode_force" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined!
ERROR: "mtk_sgmii_setup_mode_an" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined!
ERROR: "mtk_w32" [drivers/net/ethernet/mediatek/mtk_eth_path.ko] undefined!
ERROR: "mtk_r32" [drivers/net/ethernet/mediatek/mtk_eth_path.ko] undefined!
This changes the loadable module name from mtk_eth_soc to mtk_eth.
I didn't see a way to leave it as mtk_eth_soc.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Should only enable HW RX_2BYTE_OFFSET function in the case NET_IP_ALIGN
equals to 2.
Signed-off-by: Mark Lee <mark-mc.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should hw_feature as hardware capability flags to check if hardware LRO
got support.
Signed-off-by: Mark Lee <mark-mc.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All path route on various SoCs all would be managed in common function
mtk_setup_hw_path that is determined by the both applied devicetree
regarding the path between GMAC and the target PHY or switch by the
capability of target SoC in the runtime.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SGMII related logic into a separate file, and also provides options for
forcing 1G, 2.5, AN mode for the target PHY, that can be determined from
SGMII node in DTS.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two reasons for this.
First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.
Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().
We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.
Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.
skb->xmit_more is retained (but always 0) to not cause build breakage.
This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions. Remaining drivers are converted in the next patches.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Mediatek MT7621 SoC contains the same ethernet hardware module as
used on a number of other MediaTek SoC parts. There are some minor
differences to deal with but we can use the same driver to support
them all.
This patch is based on work by Bjørn Mork <bjorn@mork.no>, and his
original patch is at:
3293bc63f5
There is an additional compatible devicetree type added, and the primary
change to the code required is to support a single interrupt (for both
RX and TX interrupts).
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[gerg@kernel.org: rebase to mainline and irq handler fix]
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix regression in multi-SKB responses to RTM_GETADDR, from Arthur
Gautier.
2) Fix ipv6 frag parsing in openvswitch, from Yi-Hung Wei.
3) Unbounded recursion in ipv4 and ipv6 GUE tunnels, from Stefano
Brivio.
4) Use after free in hns driver, from Yonglong Liu.
5) icmp6_send() needs to handle the case of NULL skb, from Eric
Dumazet.
6) Missing rcu read lock in __inet6_bind() when operating on mapped
addresses, from David Ahern.
7) Memory leak in tipc-nl_compat_publ_dump(), from Gustavo A. R. Silva.
8) Fix PHY vs r8169 module loading ordering issues, from Heiner
Kallweit.
9) Fix bridge vlan memory leak, from Ido Schimmel.
10) Dev refcount leak in AF_PACKET, from Jason Gunthorpe.
11) Infoleak in ipv6_local_error(), flow label isn't completely
initialized. From Eric Dumazet.
12) Handle mv88e6390 errata, from Andrew Lunn.
13) Making vhost/vsock CID hashing consistent, from Zha Bin.
14) Fix lack of UMH cleanup when it unexpectedly exits, from Taehee Yoo.
15) Bridge forwarding must clear skb->tstamp, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
bnxt_en: Fix context memory allocation.
bnxt_en: Fix ring checking logic on 57500 chips.
mISDN: hfcsusb: Use struct_size() in kzalloc()
net: clear skb->tstamp in bridge forwarding path
net: bpfilter: disallow to remove bpfilter module while being used
net: bpfilter: restart bpfilter_umh when error occurred
net: bpfilter: use cleanup callback to release umh_info
umh: add exit routine for UMH process
isdn: i4l: isdn_tty: Fix some concurrency double-free bugs
vhost/vsock: fix vhost vsock cid hashing inconsistent
net: stmmac: Prevent RX starvation in stmmac_napi_poll()
net: stmmac: Fix the logic of checking if RX Watchdog must be enabled
net: stmmac: Check if CBS is supported before configuring
net: stmmac: dwxgmac2: Only clear interrupts that are active
net: stmmac: Fix PCI module removal leak
tools/bpf: fix bpftool map dump with bitfields
tools/bpf: test btf bitfield with >=256 struct member offset
bpf: fix bpffs bitfield pretty print
net: ethernet: mediatek: fix warning in phy_start_aneg
tcp: change txhash on SYN-data timeout
...
linux 5.0-rc1 shows following warning on bpi-r2/mt7623 bootup:
[ 5.170597] WARNING: CPU: 3 PID: 1 at drivers/net/phy/phy.c:548 phy_start_aneg+0x110/0x144
[ 5.178826] called from state READY
....
[ 5.264111] [<c0629fd4>] (phy_start_aneg) from [<c0e3e720>] (mtk_init+0x414/0x47c)
[ 5.271630] r7:df5f5eec r6:c0f08c48 r5:00000000 r4:dea67800
[ 5.277256] [<c0e3e30c>] (mtk_init) from [<c07dabbc>] (register_netdevice+0x98/0x51c)
[ 5.285035] r8:00000000 r7:00000000 r6:c0f97080 r5:c0f08c48 r4:dea67800
[ 5.291693] [<c07dab24>] (register_netdevice) from [<c07db06c>] (register_netdev+0x2c/0x44)
[ 5.299989] r8:00000000 r7:dea2e608 r6:deacea00 r5:dea2e604 r4:dea67800
[ 5.306646] [<c07db040>] (register_netdev) from [<c06326d8>] (mtk_probe+0x668/0x7ac)
[ 5.314336] r5:dea2e604 r4:dea2e040
[ 5.317890] [<c0632070>] (mtk_probe) from [<c05a78fc>] (platform_drv_probe+0x58/0xa8)
[ 5.325670] r10:c0f86bac r9:00000000 r8:c0fbe578 r7:00000000 r6:c0f86bac r5:00000000
[ 5.333445] r4:deacea10
[ 5.335963] [<c05a78a4>] (platform_drv_probe) from [<c05a5248>] (really_probe+0x2d8/0x424)
maybe other boards using this generic driver are affected
v2:
optimization:
- phy_set_max_speed() is only needed if you want to reduce the
max speed, typically if the PHY supports 1Gbps but the MAC
supports 100Mbps only.
- The pause parameters are autonegotiated. Except you have a specific
need you normally don't need to manually fiddle with this.
- phy_start_aneg() is called implicitly by the phylib state machine,
you shouldn't call it manually except you have a good excuse.
- netif_carrier_on/netif_carrier_off in mtk_phy_link_adjust() isn't
needed. It's done by phy_link_change() in phylib.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers don't indicate they support pause. They expect MAC drivers
to enable its support if the MAC has the needed hardware. Thus MAC
drivers should not mask Pause support, but enable it.
Change a few ANDs to ORs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Nelson Chang <nelson.chang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since driver is devicetree-based, all device type and charateristic can be
determined by the compatible string and its data. It's unnecessary to
create another dependent function to check chip ID and then decide whether
the specific funciton is being supported on a certain device. It can be
totally replaced by the existing flag, so a cleanup is made by removing
the function and the only user, HWLRO.
MT2701 also have a missing HWLRO support in old code, so add it the same
patch.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve more in the existing code by reusing dma_zalloc_coherent instead
of dma_alloc_coherent with __GFP_ZERO or superfluous zeroing buffer.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call mtk_probe() is to match an entry in
of_mtk_match[], so match cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Landen Chao