[ Upstream commit cc6596fc72 ]
platform_get_resource() may fail and in this case a NULL dereference
will occur.
Fix it to use devm_platform_ioremap_resource() instead of calling
platform_get_resource() and devm_ioremap().
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee44d0b788 ]
When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.
This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.
Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d63b8d66d ]
The SDMA engine used by TEMAC halts operation when it has finished
processing of the last buffer descriptor in the buffer ring.
Unfortunately, no interrupt event is generated when this happens,
so we need to setup another mechanism to make sure DMA operation is
restarted when enough buffers have been added to the ring.
Fixes: 9274498953 ("net: add Xilinx ll_temac device driver")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d07c849cd2 ]
This adds error handling to the remaining dma_map_single() calls, so that
behavior is well defined if/when we run out of DMA memory.
Fixes: 9274498953 ("net: add Xilinx ll_temac device driver")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84823ff80f ]
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in temac_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
This is a port of the similar fix in axienet driver,
commit 7de44285c1 ("net: axienet: Fix race condition causing TX hang").
Fixes: 23ecc4bde2 ("net: ll_temac: fix checksum offload logic")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb34e98baf ]
In the DMA memory resource get failed case, the error is not
set and 0 will be returned. Fix it by removing redundant check
since devm_ioremap_resource() will handle it.
Fixes: 28ef9ebdb6 ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The "lp->phy_mode" is an enum but in this context GCC treats it as an
unsigned int so the error handling is never triggered.
Fixes: ee06b1728b ("net: axienet: add support for standard phy-mode binding")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible use-after-free issue in the axienet_probe():
1701: np = of_parse_phandle(pdev->dev.of_node, "axistream-connected", 0);
1702: if (np) {
...
1787: of_node_put(np); ---> released here
1788: lp->eth_irq = platform_get_irq(pdev, 0);
1789: } else {
...
1801: }
1802: if (IS_ERR(lp->dma_regs)) {
...
1805: of_node_put(np); ---> double released here
1806: goto free_netdev;
1807: }
We solve this problem by removing the unnecessary of_node_put().
Fixes: 28ef9ebdb6 ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Robert Hancock <hancock@sedsystems.ca>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were accessing the pointer returned from platform_get_resource before
checking if it was valid, causing an oops if it was not. Move this access
after the call to devm_ioremap_resource which does the validity check.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to use the phylink API rather than the legacy PHY
API. This allows for better support for SFP modules connected using a
1000BaseX or SGMII interface.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the axienet driver requires the use of a second devicetree
node, referenced by an axistream-connected attribute on the Ethernet
device node, which contains the resources for the AXI DMA block used by the
device. This setup is problematic for a use case we have where the Ethernet
and DMA cores are behind a PCIe to AXI bridge and the memory resources for
the nodes are injected into the platform devices using the multifunction
device subsystem - it's not easily possible for the driver to obtain the
platform-level resources from the linked device.
In order to simplify that usage model, and simplify the overall use of
this driver in general, allow for all of the resources to be kept on one
node where the resources are retrieved using platform device APIs rather
than device-tree-specific ones. The previous usage setup is still
supported if the axistream-connected attribute is specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was previously using the parent node of the specified PHY
node as the device node to register the MDIO bus on. Andrew Lunn
pointed out this is wrong as the PHY node is potentially not even
underneath the MDIO bus for the current device instance. Find the MDIO
node explicitly by looking it up by name under the controller's device
node instead.
This could potentially break existing device trees if they don't use
"mdio" as the name for the MDIO bus, but I did not find any with various
searches and Xilinx's examples all use mdio as the name so it seems like
this should be relatively safe.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, such as iMX6 with PCIe devices, crashes or hangs can
occur if the axienet device continues to perform DMA transfers after
parent devices/busses have been shut down. Shut down the axienet
interface during its shutdown callback in order to avoid this.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failing initialization on a missing MAC address property is excessive.
We can just fall back to using a random MAC instead, which at least
leaves the interface in a functioning state.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously this driver only handled interrupts from the DMA RX and TX
blocks, not from the Ethernet core itself. Add optional support for
the Ethernet core interrupt, which is used to detect rx_missed and
framing errors signalled by the hardware. In order to use this
interrupt, a third interrupt needs to be specified in the device tree.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Specify IRQF_SHARED to support shared interrupts. If the interrupt
handler is called and the device is not indicating an interrupt,
just return IRQ_NONE rather than spewing error messages.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
These registers are important for troubleshooting the state of the DMA
cores.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting the RX and TX ring sizes for this driver using
ethtool. Also increase the default RX ring size as the previous default
was far too low for good performance in some configurations.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Xilinx DMA blocks each have their own reset register, but they both
reset the entire DMA engine, so only one of them needs to be reset.
Also, when stopping the device, we need to not just command the DMA
blocks to stop, but wait for them to stop, and trigger a device reset
to ensure that they are completely stopped.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO clock divisor register setting was only applied on the initial
startup when the driver was loaded. However, this setting is cleared
when the device is reset, such as would occur when the interface was
taken down and brought up again, and so the MDIO bus would be
non-functional afterwards.
Split up the MDIO bus setup and enable into separate functions and
re-enable the bus after a device reset, to ensure that the MDIO
registers are set properly. This also allows us to remove direct access
to MDIO registers in xilinx_axienet_main.c and centralize them all in
xilinx_axienet_mdio.c.
Also, lock the MDIO bus lock around the device reset process, to avoid
MDIO accesses from occurring while the MDIO is disabled during the reset.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the MDIO is is brought up before the netdev is registered, it
should be torn down after the netdev is removed. Otherwise, PHY accesses
can potentially access freed MDIO bus references and cause a crash.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was previously always calculating the MDIO clock divisor
(from AXI bus clock to MDIO bus clock) based on the CPU clock frequency,
assuming that it is the same as the AXI bus frequency, but that
simplistic method only works on the MicroBlaze platform.
Add support for specifying the clock used for the device in the device
tree using the clock framework. If the clock is specified then it will
be used when calculating the clock divisor. The previous CPU clock
detection method is left for backward compatibility if no clock is
specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver should now build on (at least) X86 and ARM platforms, so add
them as supported platforms for the driver in Kconfig.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus for this driver was being named using the result of
of_address_to_resource on a node which may not have any resource on it,
but the return value of that call was not checked so it was using some
random value in the bus name. Change to name the MDIO bus based on the
resource start of the actual Ethernet register block.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was using in_be32 and out_be32 IO accessors which do not
exist on most platforms. Also, the use of big-endian accessors does not
seem correct as this hardware is accessed over an AXI bus which, to the
extent it has an endian-ness, is little-endian. Switch to standard
ioread32/iowrite32 accessors.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was casting skb pointers to u32 and storing them as such in
the DMA buffer descriptor, which is obviously broken on 64-bit. The area
of the buffer descriptor being used is not accessed by the hardware and
has sufficient room for a 32 or 64-bit pointer, so just store the skb
pointer as such.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1b3fa5cf85 ("net: ll_temac: Cleanup multicast filter on change")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast support have been tested and is working now.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid leaving old address table entries when using multicast. If more than
one multicast address were removed, only the first removed address would
actually be cleared.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With .ndo_set_rx_mode/temac_set_multicast_list() being called in atomic
context (holding addr_list_lock), and temac_set_multicast_list() needing
to access temac indirect registers, the mutex used to synchronize indirect
register is a no-no.
Replace it with a spinlock, and avoid sleeping in
temac_indirect_busywait().
To avoid excessive holding of the lock, which is now a spinlock, the
temac_device_reset() function is changed to only hold the lock for short
periods. With timeouts, it could be holding the spinlock for more than
2 seconds.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user has requested IFF_ALLMULTI or have set more than 4 multicast
addresses, we should just use promiscuous mode, but not set it in flags,
as it causes the interface to stay in promiscuous mode even when the
non-IFF_PROMISC condition that caused promiscuous mode to be enabled
has gone away.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On loaded systems with a preemptible kernel the mdio_wait() function may
report an error while everything is working fine:
xemaclite_mdio_wait():
xemaclite_readl() -> chip not ready
--> interrupt here (other work for some time / chip become ready)
if (time_before_eq(end, jiffies))
--> false positive error report
Replace the current code with readx_poll_timeout() which takes care
of the situation.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On loaded systems with a preemptible kernel the mdio_wait() function may
report an error while everything is working fine:
axienet_mdio_wait_until_ready():
axienet_ior() -> chip not ready
--> interrupt here (other work for some time / chip become ready)
if (time_before_eq(end, jiffies))
--> false positive error report
Replace the current code with readx_poll_timeout() which take care
of the situation.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following (similar) warning reported by kbuild test robot:
In function ‘memcpy’,
inlined from ‘smsc75xx_init_mac_address’ at drivers/net/usb/smsc75xx.c:778:3,
inlined from ‘smsc75xx_bind’ at drivers/net/usb/smsc75xx.c:1501:2:
./include/linux/string.h:355:9: warning: argument 2 null where non-null expected [-Wnonnull]
return __builtin_memcpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/usb/smsc75xx.c: In function ‘smsc75xx_bind’:
./include/linux/string.h:355:9: note: in a call to built-in function ‘__builtin_memcpy’
I've replaced the offending memcpy with ether_addr_copy, because I'm
100% sure, that of_get_mac_address can't return NULL as it returns valid
pointer or ERR_PTR encoded value, nothing else.
I'm hesitant to just change IS_ERR into IS_ERR_OR_NULL check, as this
would make the warning disappear also, but it would be confusing to
check for impossible return value just to make a compiler happy.
I'm now changing all occurencies of memcpy to ether_addr_copy after the
of_get_mac_address call, as it's very likely, that we're going to get
similar reports from kbuild test robot in the future.
Fixes: a51645f70f ("net: ethernet: support of_get_mac_address new ERR_PTR error")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The channel status register value can be very helpful when debugging
SDMA problems.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/xilinx/ll_temac_main.c:66:5: warning: symbol '_temac_ior_be' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:71:6: warning: symbol '_temac_iow_be' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:76:5: warning: symbol '_temac_ior_le' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:81:6: warning: symbol '_temac_iow_le' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:648:6: warning: symbol 'ptr_to_txbd' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:654:6: warning: symbol 'ptr_from_txbd' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "pdata->mdio_bus_id" is unsigned so this condition is always true.
This patch just removes it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_connect() function doesn't return NULL pointers. It returns
error pointers on error, so I have updated the check.
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: d84aec4215 ("net: ll_temac: Fix support for 64-bit platforms")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as TAILDESCR_PTR is written, DMA transfers might start.
Let's ensure we are ready to receive DMA IRQ's before doing that.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows custom setup of IRQ coalescing for platforms using legacy
platform_device. The irq timeout and count parameters can be used for
tuning cpu load vs. latency.
I have maintained the 0x00000400 bit in TX_CHNL_CTRL. It is specified as
unused in the documentation I have available. It does not make any
difference in the hardware I have available, so it is left in to not risk
breaking other platforms where it might be used.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Changzhong