[ Upstream commit 59b4a8fa27 ]
The cdc_ncm driver passes network connection notifications up to
usbnet_link_change(), which is the right place for any logging.
Remove the netdev_info() duplicating this from the driver itself.
This stops devices such as my "TRENDnet USB 10/100/1G/2.5G LAN"
(ID 20f4:e02b) adapter from spamming the kernel log with
cdc_ncm 2-2:2.0 enp0s2u2c2: network connection: connected
messages every 60 msec or so.
Signed-off-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201224032116.2453938-1-roland@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f33d9e2b48 ]
Starting with iOS 14 released in September 2020, connectivity using the
personal hotspot USB tethering function of iOS devices is broken.
Communication between the host and the device (for example ICMP traffic
or DNS resolution using the DNS service running in the device itself)
works fine, but communication to endpoints further away doesn't work.
Investigation on the matter shows that no UDP and ICMP traffic from the
tethered host is reaching the Internet at all. For TCP traffic there are
exchanges between tethered host and server but packets are modified in
transit leading to impossible communication.
After some trials Matti Vuorela discovered that reducing the URB buffer
size by two bytes restored the previous behavior. While a better
solution might exist to fix the issue, since the protocol is not
publicly documented and considering the small size of the fix, let's do
that.
Tested-by: Matti Vuorela <matti.vuorela@bitfactor.fi>
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Link: https://lore.kernel.org/linux-usb/CAAn0qaXmysJ9vx3ZEMkViv_B19ju-_ExN8Yn_uSefxpjS6g4Lw@mail.gmail.com/
Link: https://github.com/libimobiledevice/libimobiledevice/issues/1038
Link: https://lore.kernel.org/r/20201119172439.94988-1-corsac@corsac.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f45a4248ea upstream.
When get_registers() fails in set_ethernet_addr(),the uninitialized
value of node_id gets copied over as the address.
So, check the return value of get_registers().
If get_registers() executed successfully (i.e., it returns
sizeof(node_id)), copy over the MAC address using ether_addr_copy()
(instead of using memcpy()).
Else, if get_registers() failed instead, a randomly generated MAC
address is set as the MAC address instead.
Reported-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Tested-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9666ea66a7 ]
Adds the missing .stop entry in the Belkin driver_info structure.
Fixes: e20bd60bf6 ("net: usb: asix88179_178a: Add support for the Belkin B2B128")
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4202c9fdf0 ]
Some WinCE devices face connectivity issues via the NDIS interface. They
fail to register, resulting in -110 timeout errors and failures during the
probe procedure.
In this kind of WinCE devices, the Windows-side ndis driver needs quite
more time to be loaded and configured, so that the linux rndis host queries
to them fail to be responded correctly on time.
More specifically, when INIT is called on the WinCE side - no other
requests can be served by the Client and this results in a failed QUERY
afterwards.
The increase of the waiting time on the side of the linux rndis host in
the command-response loop leaves the INIT process to complete and respond
to a QUERY, which comes afterwards. The WinCE devices with this special
"feature" in their ndis driver are satisfied by this fix.
Signed-off-by: Olympia Giannou <olympia.giannou@leica-geosystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a609d02591 ]
Keenetic Plus DSL is a xDSL modem that uses dm9620 as its USB interface.
Signed-off-by: Kamil Lorenc <kamil@re-ws.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a092b7233f upstream.
The buffer size is 2 Bytes and we expect to receive the same amount of
data. But sometimes we receive less data and run into uninit-was-stored
issue upon read. Hence modify the error check on the return value to match
with the buffer size as a prevention.
Reported-and-tested by: syzbot+a7e220df5a81d1ab400e@syzkaller.appspotmail.com
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea060b3526 ]
Drop the bogus endpoint-lookup helper which could end up accepting
interfaces based on endpoints belonging to unrelated altsettings.
Note that the returned bulk pipes and interrupt endpoint descriptor
were never actually used. Instead the bulk-endpoint numbers are
hardcoded to 1 and 2 (matching the specification), while the interrupt-
endpoint descriptor was assumed to be the third descriptor created by
USB core.
Try to bring some order to this by dropping the bogus lookup helper and
adding the missing endpoint sanity checks while keeping the interrupt-
descriptor assumption for now.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e0484010ec ]
On sparc32, tcflag_t is "unsigned long", unlike on all other
architectures, where it is "unsigned int":
drivers/net/usb/hso.c: In function ‘hso_serial_set_termios’:
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 4 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 5 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
As "unsigned long" is 32-bit on sparc32, fix this by casting all tcflag_t
parameters to "unsigned int".
While at it, use "%u" to format unsigned numbers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63634aa679 ]
The interrupt URB transfer-buffer was never freed on disconnect or after
probe errors.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d8e95fd6d ]
Add the missing endpoint sanity check to prevent a NULL-pointer
dereference should a malicious device lack the expected endpoints.
Note that the driver has a broken endpoint-lookup helper,
lan78xx_get_endpoints(), which can end up accepting interfaces in an
altsetting without endpoints as long as *some* altsetting has a bulk-in
and a bulk-out endpoint.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c28d9a2856 ]
If ax88172a_unbind() fails, make sure that the return code is
less than zero so that cleanup is done properly and avoid UAF.
Fixes: a9a51bd727 ("ax88172a: fix information leak on short answers")
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reported-by: syzbot+4cd84f527bf4a10fc9c1@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ed58f96a7 ]
In a case where the ID_REV register read is failed, the memory for a
private data structure has to be freed before returning error from the
function smsc95xx_bind.
Fixes: bbd9f9ee69 ("smsc95xx: add wol support for more frame types")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c8b1e855f ]
The return value of the function smsc95xx_reset() must be checked
to avoid returning false success from the function smsc95xx_bind().
Fixes: 2f7ca802bd ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b835a71ef6 ]
Syzbot reports an use-after-free in workqueue context:
BUG: KASAN: use-after-free in mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
__smsc95xx_mdio_read drivers/net/usb/smsc95xx.c:217 [inline]
smsc95xx_mdio_read+0x583/0x870 drivers/net/usb/smsc95xx.c:278
check_carrier+0xd1/0x2e0 drivers/net/usb/smsc95xx.c:644
process_one_work+0x777/0xf90 kernel/workqueue.c:2274
worker_thread+0xa8f/0x1430 kernel/workqueue.c:2420
kthread+0x2df/0x300 kernel/kthread.c:255
It looks like that smsc95xx_unbind() is freeing the structures that are
still in use by the concurrently running workqueue callback. Thus switch
to using cancel_delayed_work_sync() to ensure the work callback really
is no longer active.
Reported-by: syzbot+29dc7d4ae19b703ff947@syzkaller.appspotmail.com
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e869e7a177 ]
Using a AX88179 device (0b95:1790), I see two bytes of appended data on
every RX packet. For example, this 48-byte ping, using 0xff as a
payload byte:
04:20:22.528472 IP 192.168.1.1 > 192.168.1.2: ICMP echo request, id 2447, seq 1, length 64
0x0000: 000a cd35 ea50 000a cd35 ea4f 0800 4500
0x0010: 0054 c116 4000 4001 f63e c0a8 0101 c0a8
0x0020: 0102 0800 b633 098f 0001 87ea cd5e 0000
0x0030: 0000 dcf2 0600 0000 0000 ffff ffff ffff
0x0040: ffff ffff ffff ffff ffff ffff ffff ffff
0x0050: ffff ffff ffff ffff ffff ffff ffff ffff
0x0060: ffff 961f
Those last two bytes - 96 1f - aren't part of the original packet.
In the ax88179 RX path, the usbnet rx_fixup function trims a 2-byte
'alignment pseudo header' from the start of the packet, and sets the
length from a per-packet field populated by hardware. It looks like that
length field *includes* the 2-byte header; the current driver assumes
that it's excluded.
This change trims the 2-byte alignment header after we've set the packet
length, so the resulting packet length is correct. While we're moving
the comment around, this also fixes the spelling of 'pseudo'.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c27a204383 ]
Device id 0927 is the RTL8153B-based component of the 'Surface USB-C to
Ethernet and USB Adapter' and may be used as a component of other devices
in future. Tested and working with the r8152 driver.
Update the cdc_ether blacklist due to the RTL8153 'network jam on suspend'
issue which this device will cause (personally confirmed).
Signed-off-by: Marc Payne <marc.payne@mdpsys.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57c7f2bd75 ]
Add support for Dell Wireless 5816e to drivers/net/usb/qmi_wwan.c
Signed-off-by: Matt Jolly <Kangie@footclan.ninja>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eae7172f81 ]
usbnet creates network interfaces with min_mtu = 0 and
max_mtu = ETH_MAX_MTU.
These values are not modified by qmi_wwan when the network interface
is created initially, allowing, for example, to set mtu greater than 1500.
When a raw_ip switch is done (raw_ip set to 'Y', then set to 'N') the mtu
values for the network interface are set through ether_setup, with
min_mtu = ETH_MIN_MTU and max_mtu = ETH_DATA_LEN, not allowing anymore to
set mtu greater than 1500 (error: mtu greater than device maximum).
The patch restores the original min/max mtu values set by usbnet after a
raw_ip switch.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d64c7a0803 ]
Dell USB Type C docking WD19/WD19DC attaches additional peripherals as:
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
|__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 4: Dev 13, If 0, Class=Vendor Specific Class,
Driver=r8152, 5000M
where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock.
When hotplugging such dock with additional usb devices already attached on
it, the probing process may reset usb 2.1 port, therefore r8152 ethernet
device is also reset. However, during r8152 device init there are several
for-loops that, when it's unable to retrieve hardware registers due to
being disconnected from USB, may take up to 14 seconds each in practice,
and that has to be completed before USB may re-enumerate devices on the
bus. As a result, devices attached to the dock will only be available
after nearly 1 minute after the dock was plugged in:
[ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface
[ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id
[ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready
[ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr
[ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail
This happens in, for example, r8153_init:
static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size,
void *data, u16 type)
{
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return -ENODEV;
...
}
static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index)
{
u32 data;
...
generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen);
data = __le32_to_cpu(tmp);
...
return (u16)data;
}
static void r8153_init(struct r8152 *tp)
{
...
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return;
for (i = 0; i < 500; i++) {
if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
AUTOLOAD_DONE)
break;
msleep(20);
}
...
}
Since ocp_read_word() doesn't check the return status of
generic_ocp_read(), and the only exit condition for the loop is to have
a match in the returned value, such loops will only ends after exceeding
its maximum runs when the device has been marked as disconnected, which
takes 500 * 20ms = 10 seconds in theory, 14 in practice.
To solve this long latency another test to RTL8152_UNPLUG flag should be
added after those 20ms sleep to skip unnecessary loops, so that the device
probe can complete early and proceed to parent port reset/reprobe process.
This can be reproduced on all kernel versions up to latest v5.6-rc2, but
after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less
while it was around 1/2.
Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00516d13d4 ]
We have been using the fact that the QMI and DIAG functions
usually are the only ones with class/subclass/protocol being
ff/ff/ff on Quectel modems. This has allowed us to match the
QMI function without knowing the exact interface number,
which can vary depending on firmware configuration.
The ability to silently reject the DIAG function, which is
usually handled by the option driver, is important for this
method to work. This is done based on the knowledge that it
has exactly 2 bulk endpoints. QMI function control interfaces
will have either 3 or 1 endpoint. This rule is universal so
the quirk condition can be removed.
The fixed layouts known from the Gobi1k and Gobi2k modems
have been gradually replaced by more dynamic layouts, and
many vendors now use configurable layouts without changing
device IDs. Renaming the class/subclass/protocol matching
macro makes it more obvious that this is now not Quectel
specific anymore.
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88bf54603f ]
Commit f25e1392fd removed the support for the pre-production variant
of the Dell DW5821e to avoid probing another USB interface unnecessarily.
However, the pre-production samples are found in the wild, and this lack
of support is causing problems for users of such samples. It is therefore
necessary to support both variants.
Matching on both interfaces 0 and 1 is not expected to cause any problem
with either variant, as only the QMI function will be probed successfully
on either. Interface 1 will be rejected based on the HID class for the
production variant:
T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev=03.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
And interface 0 will be rejected based on too few endpoints for the
pre-production variant:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev= 3.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
Fixes: f25e1392fd ("qmi_wwan: fix interface number for DW5821e production firmware")
Link: https://whrl.pl/Rf0vNk
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa475d9352 ]
When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1981316289 ]
Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7f1b59655 ]
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause
abnormal behavior for the device randomly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08997b5eec ]
PLA MCU clock speed down could only be enabled when tx/rx are disabled.
Otherwise, the packet loss may occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 809a7fc659 ]
Enable U2P3 may miss zero packet for bulk-in.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9583a3638d ]
Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9ff44f0e6 ]
RM500Q is a 5G module from Quectel, supporting both standalone and
non-standalone modes. The normal Quectel quirks apply (DTR and dynamic
interface numbers).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce896476c6 ]
As reported by Eric Dumazet, there are still some outstanding
cases where the driver does not handle TSO correctly when skb's
are over a certain size. Most cases have been fixed, this patch
should ensure that forwarded SKB's that are greater than
MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented
and handled correctly.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86f3f4cd53 ]
Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.
Fixes: 40a82917b1 ("net/usb/r8152: enable interrupt transfer")
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f8d7408a4d ]
lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.
Pierre-Francois reported various hangs when/if TSO is enabled.
For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.
Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Tested-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47240ba0cd ]
If skb_linearize() fails, we need to free the skb.
TSO makes skb bigger, and this bug might be the reason
Raspberry Pi 3B+ users had to disable TSO.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20032b6358 ]
Lan78xx driver accesses the PHY registers through MDIO bus over USB
connection. When performing a suspend/resume, the PHY registers can be
accessed before the USB connection is resumed. This will generate an
error and will prevent the device to resume correctly.
This patch adds the dependency between the MDIO bus and USB device to
allow correct handling of suspend/resume.
Fixes: ce85e13ad6 ("lan78xx: Update to use phylib instead of mii_if_info.")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call napi_disable() twice would cause dead lock. There are three situations
may result in the issue.
1. rtl8152_pre_reset() and set_carrier() are run at the same time.
2. Call rtl8152_set_tunable() after rtl8152_close().
3. Call rtl8152_set_ringparam() after rtl8152_close().
For #1, use the same solution as commit 8481141246 ("r8152: Re-order
napi_disable in rtl8152_close"). For #2 and #3, add checking the flag
of IFF_UP and using napi_disable/napi_enable during mutex.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both rtl_work_func_t() and rtl8152_close() call napi_disable().
Since the two calls aren't protected by a lock, if the close
function starts executing before the work function, we can get into a
situation where the napi_disable() function is called twice in
succession (first by rtl8152_close(), then by set_carrier()).
In such a situation, the second call would loop indefinitely, since
rtl8152_close() doesn't call napi_enable() to clear the NAPI_STATE_SCHED
bit.
The rtl8152_close() function in turn issues a
cancel_delayed_work_sync(), and so it would wait indefinitely for the
rtl_work_func_t() to complete. Since rtl8152_close() is called by a
process holding rtnl_lock() which is requested by other processes, this
eventually leads to a system deadlock and crash.
Re-order the napi_disable() call to occur after the work function
disabling and urb cancellation calls are issued.
Change-Id: I6ef0b703fc214998a037a68f722f784e1d07815e
Reported-by: http://crbug.com/1017928
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a malicious device gives a short MAC it can elicit up to
5 bytes of leaked memory out of the driver. We need to check for
ETH_ALEN instead.
Reported-by: syzbot+a8d4acdad35e6bbca308@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.
Fixes: 332f989a3b ("CDC-NCM: handle incomplete transfer of MTU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A malicious device may give half an answer when asked
for its MTU. The driver will proceed after this with
a garbage MTU. Anything but a complete answer must be treated
as an error.
V2: used sizeof as request by Alexander
Reported-and-tested-by: syzbot+0631d878823ce2411636@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork