When roaming while we have active BA session,
we can end up transmitting delBA frames to
the old AP while we're already on the new AP's
channel, which can cause warnings.
Simply avoid sending those frames, but still
tear down the internal session state, since
they are not really necessary anyway as we
will implicitly disassociate when sending the
association to the new AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Be consistent and use the wk->chan instead of the
local->hw.conf.channel for the association done work.
This prevents any possible races against channel changes
while we run this work.
In the case that the race did happen we would be initializing
the bit rates for the new AP under the assumption of a wrong
channel and in the worst case, wrong band. This could lead
to trying to assuming we could use CCK frames on 5 GHz, for
example.
This patch has a fix for kernels >= v2.6.34
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking around ieee80211_recalc_smps is
buggy -- it cannot acquire another interface's
mutex while the iflist mutex is held because
another code path could be holding the iface
mutex and trying to acquire the iflist mutex.
But the locking is also unnecessary, we only
check "ifmgd->associated" as a bool, and don't
use the pointer (in check_mgd_smps).
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On association to an AP, after receiving beacons, the beacon_crc value is set.
The beacon_crc value is not reset in disassociation, but the BSS data may be
expired at a later point. When associating again, it's possible that a
beacon for the AP is not received, resulting in the beacon_ies to remain NULL.
After association, further beacons will not update the beacon data, as the
crc value of the beacon has not changed, and the beacon_crc still holds a
value matching the beacon. The beacon_ies will remain forever null.
One of the results of this is that WLAN power save cannot be entered, the STA
will remain foreven in active mode.
Fix this by adding a validation flag for the beacon_crc, which is cleared on
association.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WMM parameter configuration function (ieee80211_sta_wmm_params) only
configures the WMM parameters to the driver is the wmm_last_param_set
counter value is changed by the AP.
The wmm_last_param_set is initialized to -1 on association in order to ensure
the configuration is made to the driver at least once on association, but
currently this initialization is done *after* the WMM parameter configuration
function was called.
This leads to unreliability in the driver getting properly configured on first
association (depending on what counter value the AP happens to use.) When
disassociating (the wmm default parameters are configured to the driver) and
then reassociating, due to the above the WMM configuration is not set to the
driver at all.
On drivers without beacon filtering the problem is corrected by later beacons,
but on drivers with beacon filtering the WMM will remain permanently incorrectly
configured.
Fix this by moving the initialization of wmm_last_param_set to -1 before
ieee80211_sta_wmm_params is called on association.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some buggy APs do not respond to unicast probe requests
or send unicast probe requests very delayed so in the
worst case we should try to send broadcast probe requests,
otherwise we can get disconnected from these APs.
Even if drivers do not have filters to disregard probe
responses from foreign APs mac80211 will only process
probe responses from our associated AP for re-arming
connection monitoring.
We need to do this since the beacon monitor does not
push back the connection monitor by design so even if we
are getting beacons from these type of APs our connection
monitor currently relies heavily on the way the probe
requests are received on the AP. An example of an AP
affected by this is the Nexus One, but this has also been
observed with random APs.
We can probably optimize this later by using null funcs
instead of probe requests.
For more details refer to:
http://code.google.com/p/chromium-os/issues/detail?id=5715
This patch has fixes for stable kernels [2.6.35+].
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used by other components next. The beacon
monitor was added as of 2.6.34 so these fixes are applicable
only to kernels >= 2.6.34.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon beacon loss we send probe requests after 30 seconds of idle
time and we wait for each probe response 1/2 second. We send a
total of 3 probe requests before giving up on the AP. In the case
that we reset the connection idle monitor we should reset the probe
requests count to 0. Right now this won't help in any way but
the next patch will.
This patch has fixes for stable kernel [2.6.35+].
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used in another place later. The connection
monitor was added as of 2.6.35 so these fixes will be
applicable to >= 2.6.35.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a WARN_ON(!mutex_is_locked())
use lockdep_assert_held() which compiles away
completely when lockdep isn't enabled, and
also is a more accurate assertion since it
checks that the current thread is holding the
mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signal strength value in a single RX frame is not that reliable,
so it is better to delay start of CQM events until there is a real
average signal strength from more than a single Beacon frame
available.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ave_beacon_signal value uses 1/16 dB unit and as such, must be
initialized with the signal level of the first Beacon frame multiplied
by 16. This fixes an issue where the initial CQM events are reported
incorrectly with a burst of events while the running average
approaches the correct value after the incorrect initialization. This
could cause user space -based roaming decision process to get quite
confused at the moment when we would like to go through authentication
and DHCP.
Cc: stable@kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a lot of redundant code in mac80211's
interface cleanup/down, for example freeing
AP beacons is done both when the interface is
set DOWN as well as when it is torn down, of
which only the former has any effect.
Also, a bunch of things should be closer to
where they matter, like the MLME timers that
we should cancel when disassociating, rather
than only when the interface is set DOWN.
Clean up all this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Support this
in mac80211 via the cfg80211 API for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize logging messages from
printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
wiphy_<level>(foo, fmt, args);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes drivers have more information than the
stack about how their antennas/chains are used,
and may require that the SM PS mode be changed.
This could happen, for example, when detecting
that the user disconnected an antenna. Thus this
patch introduces API to allow drivers to request
SM PS mode changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes we don't just need to know whether or
not the device is idle, but also per interface.
This adds that reporting capability to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having both scan and work mutexes is not just
a bit too fine grained, it also creates issues
when there's code that needs both since they
then need to be acquired in the right order,
which can be hard to do.
Therefore, use just a single mutex for both.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some features require knowing the DTIM period
before associating. This implements the ability
to wait for a beacon in mac80211 before assoc
to provide this value. It is optional since
most likely not all drivers will need this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WEP is not available, we should reject shared
key authentication because it could never succeed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since
commit e1b3ec1a2a
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Mon Mar 29 12:18:34 2010 +0200
mac80211: explicitly disable/enable QoS
mac80211 is telling drivers, in particular
iwlwifi, whether QoS is enabled or not.
However, this is only relevant for station mode,
since only then will any device send nullfunc
frames and need to know whether they should be
QoS frames or not. In other modes, there are
(currently) no frames the device is supposed to
send.
When you now consider virtual interfaces, it
becomes apparent that the current mechanism is
inadequate since it enables/disables QoS on a
global scale, where for nullfunc frames it has
to be on a per-interface scale.
Due to the above considerations, we can change
the way mac80211 advertises the QoS state to
drivers to only ever advertise it as "off" in
station mode, and make it a per-BSS setting.
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This mechanism introduced in this patch applies (at least) for hardware
designs using a single shared antenna for both WLAN and BT. In these designs,
the antenna must be toggled between WLAN and BT.
In those hardware, managing WLAN co-existence with Bluetooth requires WLAN
full power save whenever there is Bluetooth activity in order for WLAN to be
able to periodically relinquish the antenna to be used for BT. This is because
BT can only access the shared antenna when WLAN is idle or asleep.
Some hardware, for instance the wl1271, are able to indicate to the host
whenever there is BT traffic. In essence, the hardware will send an indication
to the host whenever there is, for example, SCO traffic or A2DP traffic, and
will send another indication when the traffic is over.
The hardware gets information of Bluetooth traffic via hardware co-existence
control lines - these lines are used to negotiate the shared antenna
ownership. The hardware will give the antenna to BT whenever WLAN is sleeping.
This patch adds the interface to mac80211 to facilitate temporarily disabling
of dynamic power save as per request of the WLAN driver. This interface will
immediately force WLAN to full powersave, hence allowing BT coexistence as
described above.
In these kind of shared antenna desings, when WLAN powersave is fully disabled,
Bluetooth will not work simultaneously with WLAN at all. This patch does not
address that problem. This interface will not change PSM state, so if PSM is
disabled it will remain so. Solving this problem requires knowledge about BT
state, and is best done in user-space.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When management frame protection (IEEE 802.11w) is used,
Deauthentication frame needs to be protected when the pairwise key is
configured. mac80211 was removing the station entry (and its keys)
before actually sending out the Deauthentication frame. Fix this by
reordering the code to send the frame before the station entry gets
removed. This matches an earlier change that handled the Disassociation
frame processing, but missed Deauthentication frames.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ps-qos latency handling is broken. It uses predetermined latency values
to select specific dynamic PS timeouts. With common AP configurations, these
values overlap with beacon interval and are therefore essentially useless
(for network latencies less than the beacon interval, PSM is disabled.)
This patch remedies the problem by replacing the predetermined network latency
values with one high value (1900ms) which is used to go trigger full psm. For
backwards compatibility, the value 2000ms is still mapped to a dynamic ps
timeout of 100ms.
Currently also the mac80211 internal value for storing user space configured
dynamic PSM values is incorrectly in the driver visible ieee80211_conf struct.
Move it to the ieee80211_local struct.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a circular locking dependency when configuring the
hardware ARP filters on association, occurring when flushing the mac80211
workqueue. This is what happens:
[ 92.026800] =======================================================
[ 92.030507] [ INFO: possible circular locking dependency detected ]
[ 92.030507] 2.6.34-04781-g2b2c009 #85
[ 92.030507] -------------------------------------------------------
[ 92.030507] modprobe/5225 is trying to acquire lock:
[ 92.030507] ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8105b5c0>] flush_workq
ueue+0x0/0xb0
[ 92.030507]
[ 92.030507] but task is already holding lock:
[ 92.030507] (rtnl_mutex){+.+.+.}, at: [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507]
[ 92.030507] which lock already depends on the new lock.
[ 92.030507]
[ 92.030507]
[ 92.030507] the existing dependency chain (in reverse order) is:
[ 92.030507]
[ 92.030507] -> #2 (rtnl_mutex){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff81341754>] mutex_lock_nested+0x44/0x300
[ 92.030507] [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507] [<ffffffffa022d47c>] ieee80211_assoc_done+0x6c/0xe0 [mac80211]
[ 92.030507] [<ffffffffa022f2ad>] ieee80211_work_work+0x31d/0x1280 [mac80211]
[ 92.030507] -> #1 ((&local->work_work)){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105a51a>] worker_thread+0x22a/0x370
[ 92.030507] [<ffffffff8105ecc6>] kthread+0x96/0xb0
[ 92.030507] [<ffffffff81003a94>] kernel_thread_helper+0x4/0x10
[ 92.030507]
[ 92.030507] -> #0 ((wiphy_name(local->hw.wiphy))){+.+.+.}:
[ 92.030507] [<ffffffff81075fdc>] __lock_acquire+0x1c0c/0x1d50
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105b60e>] flush_workqueue+0x4e/0xb0
[ 92.030507] [<ffffffffa023ff7b>] ieee80211_stop_device+0x2b/0xb0 [mac80211]
[ 92.030507] [<ffffffffa0231635>] ieee80211_stop+0x3e5/0x680 [mac80211]
The locking in this case is quite complex. Fix the problem by rewriting the
way the hardware ARP filter list is handled - i.e. make a copy of the address
list to the bss_conf struct, and provide that list to the hardware driver
when needed.
The current patch will enable filtering also in promiscuous mode. This may need
to be changed in the future.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for making the ampdu_action callback
sleep, make mac80211 always process blockack
action frames from the skb queue. This gets rid
of the current special case for managed mode
interfaces as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some code is duplicated between ibss, mesh and
managed mode regarding the queueing of management
frames. Since all modes now use a common skb
queue and a common work function, we can pull
the queueing code into the rx handler directly
and remove the duplicated length checks etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the management processing functions free the
skb after they are done, so this can be done in
the new common code instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even with the previous patch, IBSS, managed
and mesh modes all attach their own work
function to the shared work struct, which
means some duplicated code. Change that to
only have a frame processing function and a
further work function for each of them and
share some common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS, managed and mesh modes all have their
own work struct, and in the future we want
to also use it in other modes to process
frames from the now common skb queue.
This also makes the skb queue and work safe
to use from other interface types.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS, managed and mesh modes all have an
skb queue, and in the future we want to
also use it in other modes, so make them
all use a common skb queue already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of places use RCU locking for accessing
the station list, even though they do not need
to. Use mutex locking instead to prepare for the
locking changes I want to make. The mlme code is
also using a WLAN_STA_DISASSOC flag that has the
same meaning as WLAN_STA_BLOCK_BA, so use that.
While doing so, combine places where we loop
over stations twice, and optimise away some of
the loops by checking if the hardware supports
aggregation at all first.
Also fix a more theoretical race condition: right
now we could resume, set up an aggregation session,
and right after tear it down again due to the code
that is needed for hardware reconfiguration here.
Also mark add a comment to that code marking it as
a workaround.
Finally, remove a pointless aggregation disabling
loop when an interface is stopped, directly after
that we remove all stations from it which will also
disable all aggregation sessions that may still be
active, and does so in a race-free way unlike the
current loop that doesn't block new sessions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When in IBSS mode, currently action frame TX and RX
cannot be used. Allow using it to talk to any peer,
or for public action frames. Also, while at it,
restructure the code in mac80211 to make it easier
to add this for other interface types in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we receive a deauthentication frame before
having successfully associated, we neither print
a message nor abort assocation. The former makes
it hard to debug, while the latter later causes
a warning in cfg80211 when, as will typically be
the case, association timed out.
This warning was reported by many, e.g. in
https://bugzilla.kernel.org/show_bug.cgi?id=15981,
but I couldn't initially pinpoint it. I verified
the fix by hacking hostapd to send a deauth frame
instead of an association response.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: make ARP filtering depend on CONFIG_INET" introduced this
potential locking leak.
Reported-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Processing an association response could take a bit
of time while we set up the hardware etc. During that
time, the AP might already send a blockack request.
If this happens very quickly on a fairly slow machine,
we can end up processing the blockack request before
the association processing has finished. Since the
blockack processing cannot sleep right now, we also
cannot make it wait in the driver.
As a result, sometimes on slow machines the iwlagn
driver gets totally confused, and no traffic can pass
when the aggregation setup was done before the assoc
setup completed.
I'm working on a proper fix for this, which involves
queuing all blockack category action frames from a
work struct, and also allowing the ampdu_action driver
callback to sleep, which will generally clean up the
code and make things easier.
However, this is a very involved and complex change.
To fix the problem at hand in a way that can also be
backported to stable, I've come up with this patch.
Here, I simply process all aggregation action frames
from the managed interface skb queue, which means
their processing will be serialized with processing
the association response, thereby fixing the problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware allow extended filtering of ARP frames not intended for
the host. To perform such filtering, the hardware needs to know the current
IP address(es) of the host, bound to its interface.
Add support for ARP filtering to mac80211 by adding a new op to the driver
interface, allowing to configure the current IP addresses. This op is called
upon association with the currently configured address(es), and when
associated whenever the IP address(es) change.
This patch adds configuration of IPv4 addresses only, as IPv6 addresses don't
need ARP filtering.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending action frames, we want to verify
that we do that on the correct channel. However,
checking the channel type in addition can get in
the way, since the channel type could change on
the fly during an association, and it's not
useful to have the channel type anyway since it
has no effect on the transmission. Therefore,
make it optional to specify so that if wanted,
it can still be checked, but is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
Check the mode in channel switch ie for either 0 or 1 on transmission.
A channel switch mode set to 1 means that the STA in a BSS to which the
frame containing the element is addressed shall transmit no further
frames within the BSS until the scheduled channel switch.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for offloading the channel switch
operation to devices that support such, typically
by having specific firmware API for it. The reasons
for this could be that the firmware provides better
timing or that regulatory enforcement done by the
device requires special handling of CSAs.
In order to allow drivers to specify the timing to
the device, the new channel_switch callback will
pass through the received frame's mactime, where
available.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg