The register SDHCI_CLOCK_CONTROL should be cleared before config clock
divider, otherwise the frequency configured maybe lower than we
expected.
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The OCR register defines the supported range of VDD voltages for SD cards.
However, it has turned out that some SD cards reports an invalid voltage
range, for example having bit7 set.
When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from
the invalid VDD range, this triggers the core to run a power cycle of the
card to try to initialize it at the lowest common supported voltage.
Obviously this fails, since the card can't support it.
Let's fix this problem, by clearing invalid bits from the read OCR register
for SD cards, before proceeding with the VDD voltage negotiation.
Cc: stable@vger.kernel.org
Reported-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Philip Langdale <philipl@overt.org>
Tested-by: Philip Langdale <philipl@overt.org>
Tested-by: Manuel Presnitz <mail@mpy.de>
-----BEGIN PGP SIGNATURE-----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=u7jL
-----END PGP SIGNATURE-----
Merge tag '5.3-rc6-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"A few small SMB3 fixes, and a larger one to fix various older string
handling functions"
* tag '5.3-rc6-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
cifs: replace various strncpy with strscpy and similar
cifs: Use kzfree() to zero out the password
cifs: set domainName when a domain-key is used in multiuser
Get the vlan_proto of ingress bridge in network byteorder as userspace
expects. Otherwise this is inconsistent with NFT_META_PROTOCOL.
Fixes: 2a3a93ef0b ("netfilter: nft_meta_bridge: Add NFT_META_BRI_IIFVPROTO support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
- Make qxl reservel the vga ports using vgaargb to prevent switching to vga compatibility mode.
- Fix omap port lookup for SDI output
- Use virtio_max_dma_size to fix an issue with swiotlb.
- Compiler fixes to komeda.
- Add missing of_node_get() call in komeda.
- Reorder the komeda de-init functions.
-----BEGIN PGP SIGNATURE-----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=UuWS
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2019-08-28' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.3 (rc7?):
- Make qxl reservel the vga ports using vgaargb to prevent switching to vga compatibility mode.
- Fix omap port lookup for SDI output
- Use virtio_max_dma_size to fix an issue with swiotlb.
- Compiler fixes to komeda.
- Add missing of_node_get() call in komeda.
- Reorder the komeda de-init functions.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f187c28b-6279-2c4f-3e53-296ee899133b@linux.intel.com
* one fix for a driver as I'm covering for Kalle while he's on vacation
* two fixes for eapol-over-nl80211 work
-----BEGIN PGP SIGNATURE-----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=P47S
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have
* one fix for a driver as I'm covering for Kalle while he's on vacation
* two fixes for eapol-over-nl80211 work
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Family 16h Model 30h SMBus controller needs the same port selection fix
as described and fixed in commit 0fe16195f8 ("i2c: piix4: Fix SMBus port
selection for AMD Family 17h chips")
commit 6befa3fde6 ("i2c: piix4: Support alternative port selection
register") also fixed the port selection for Hudson2, but unfortunately
this is not the exact same device and the AMD naming and PCI Device IDs
aren't particularly helpful here.
The SMBus port selection register is common to the following Families
and models, as documented in AMD's publicly available BIOS and Kernel
Developer Guides:
50742 - Family 15h Model 60h-6Fh (PCI_DEVICE_ID_AMD_KERNCZ_SMBUS)
55072 - Family 15h Model 70h-7Fh (PCI_DEVICE_ID_AMD_KERNCZ_SMBUS)
52740 - Family 16h Model 30h-3Fh (PCI_DEVICE_ID_AMD_HUDSON2_SMBUS)
The Hudson2 PCI Device ID (PCI_DEVICE_ID_AMD_HUDSON2_SMBUS) is shared
between Bolton FCH and Family 16h Model 30h, but the location of the
SmBus0Sel port selection bits are different:
51192 - Bolton Register Reference Guide
We distinguish between Bolton and Family 16h Model 30h using the PCI
Revision ID:
Bolton is device 0x780b, revision 0x15
Family 16h Model 30h is device 0x780b, revision 0x1F
Family 15h Model 60h and 70h are both device 0x790b, revision 0x4A.
The following additional public AMD BKDG documents were checked and do
not share the same port selection register:
42301 - Family 15h Model 00h-0Fh doesn't mention any
42300 - Family 15h Model 10h-1Fh doesn't mention any
49125 - Family 15h Model 30h-3Fh doesn't mention any
48751 - Family 16h Model 00h-0Fh uses the previously supported
index register SB800_PIIX4_PORT_IDX_ALT at 0x2e
Signed-off-by: Andrew Cooks <andrew.cooks@opengear.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org [v4.6+]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ftrace does not use text_poke() for enabling trace functionality. It uses
its own mechanism and flips the whole kernel text to RW and back to RO.
The CPA rework removed a loop based check of 4k pages which tried to
preserve a large page by checking each 4k page whether the change would
actually cover all pages in the large page.
This resulted in endless loops for nothing as in testing it turned out that
it actually never preserved anything. Of course testing missed to include
ftrace, which is the one and only case which benefitted from the 4k loop.
As a consequence enabling function tracing or ftrace based kprobes results
in a full 4k split of the kernel text, which affects iTLB performance.
The kernel RO protection is the only valid case where this can actually
preserve large pages.
All other static protections (RO data, data NX, PCI, BIOS) are truly
static. So a conflict with those protections which results in a split
should only ever happen when a change of memory next to a protected region
is attempted. But these conflicts are rightfully splitting the large page
to preserve the protected regions. In fact a change to the protected
regions itself is a bug and is warned about.
Add an exception for the static protection check for kernel text RO when
the to be changed region spawns a full large page which allows to preserve
the large mappings. This also prevents the syslog to be spammed about CPA
violations when ftrace is used.
The exception needs to be removed once ftrace switched over to text_poke()
which avoids the whole issue.
Fixes: 585948f4f6 ("x86/mm/cpa: Avoid the 4k pages check completely")
Reported-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1908282355340.1938@nanos.tec.linutronix.de
Make sure interrupt handler i2c_dw_irq_handler_slave() has finished
before clearing the the dev->slave pointer in i2c_dw_unreg_slave().
There is possibility for a race if i2c_dw_irq_handler_slave() is running
on another CPU while clearing the dev->slave pointer.
Reported-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
check_acpi_smo88xx_device() utilizes acpi_get_object_info() which in its turn
allocates a buffer. User is responsible to clean allocated resources. The last
has been missed in the original code. Fix it here.
While here, replace !ACPI_SUCCESS() with ACPI_FAILURE().
Fixes: 19b07cb4a1 ("i2c: i801: Register optional lis3lv02d I2C device on Dell machines")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We are moving towards returning ERR_PTRs when i2c_new_*_device() calls
fail. Make sure its counterpart for unregistering handles ERR_PTRs as
well.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hi Linus,
Please, pull the following patches that mark switch cases where we are
expecting to fall through.
- Fix fall-through warnings on arc and nds32 for multiple
configurations.
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----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=L0Bt
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fallthrough fixes from Gustavo A. R. Silva:
"Fix fall-through warnings on arc and nds32 for multiple
configurations"
* tag 'Wimplicit-fallthrough-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
nds32: Mark expected switch fall-throughs
ARC: unwind: Mark expected switch fall-through
- Add a 'depends on' in the core Kconfig entry to avoid build errors.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl1nxnIACgkQJWrqGEe9
VoQpjgf9HwlyuuAAmLfkeIWSCuYBQGztzfWaH0RPFyidGmMUBLymnqdnTclWbSWx
IsXSRZ2uSykwzRuUAflaAIjaZPuSIUaEIvbIT/Q/LzCIewhfWa0akVG/dwCrCRas
o15jXL7TGyn18moCi437iTBIA0yFcYL792spNDoqJVsnGJC3kZ2d0lXZmQtstDRG
1dIpXFUG7f2caWD98ylsZMSesaDZdMrFf5ckMQUf4HebyHS2tuMwToYI6GKgQ2t5
FlEUqriGjFXUnwUIsyvr+m3MA+z5ryIP9TPIeq46DTIGOFwf/rjO24fk38jwt739
JST0NYyHTrm1z2yjTV9LPKO/2r2ufg==
=PIzl
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fix from Miquel Raynal:
"Add a 'depends on' in the core Hyperbus Kconfig entry to avoid build
errors"
* tag 'mtd/fixes-for-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: hyperbus: fix dependency and build error
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings (Building: allmodconfig nds32):
include/math-emu/soft-fp.h:124:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/nds32/kernel/signal.c:362:20: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/nds32/kernel/signal.c:315:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:417:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:430:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:310:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:320:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:310:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:320:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/soft-fp.h:124:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:417:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:430:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:310:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:320:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:310:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/math-emu/op-common.h:320:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings (Building: haps_hs_defconfig arc):
arch/arc/kernel/unwind.c: In function ‘read_pointer’:
./include/linux/compiler.h:328:5: warning: this statement may fall through [-Wimplicit-fallthrough=]
do { \
^
./include/linux/compiler.h:338:2: note: in expansion of macro ‘__compiletime_assert’
__compiletime_assert(condition, msg, prefix, suffix)
^~~~~~~~~~~~~~~~~~~~
./include/linux/compiler.h:350:2: note: in expansion of macro ‘_compiletime_assert’
_compiletime_assert(condition, msg, __compiletime_assert_, __LINE__)
^~~~~~~~~~~~~~~~~~~
./include/linux/build_bug.h:39:37: note: in expansion of macro ‘compiletime_assert’
#define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
^~~~~~~~~~~~~~~~~~
./include/linux/build_bug.h:50:2: note: in expansion of macro ‘BUILD_BUG_ON_MSG’
BUILD_BUG_ON_MSG(condition, "BUILD_BUG_ON failed: " #condition)
^~~~~~~~~~~~~~~~
arch/arc/kernel/unwind.c:573:3: note: in expansion of macro ‘BUILD_BUG_ON’
BUILD_BUG_ON(sizeof(u32) != sizeof(value));
^~~~~~~~~~~~
arch/arc/kernel/unwind.c:575:2: note: here
case DW_EH_PE_native:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
The move of the IXP4xx SoC drivers exposed their config options on all
platforms.
Fix this by wrapping them inside an ARCH_IXP4XX or COMPILE_TEST block.
Link: https://lore.kernel.org/r/20190823090352.12243-1-linus.walleij@linaro.org
Fixes: fcf2d8978c ("ARM: ixp4xx: Move NPE and QMGR to drivers/soc")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXV5gAwAKCRDj7w1vZxhR
xb+GAP92Dr8GZp+lPy/7ZrspFqbl/FhkZXkSZgbn+XwpLgeIXwD+I807vV934FP1
ROhzRsdtA0m54wyifYIWMNkTup+zawk=
=SKiP
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
A single patch to change my MAINTAINERS address
* tag 'sunxi-fixes-for-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
MAINTAINERS: Update my email address
Link: https://lore.kernel.org/r/8c04a96b-4a75-4e1f-b3ac-05fe091f251e.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fixed RCU usage in logical PIO
- Added a function to unregister a logical PIO range in logical PIO
to support the fixes in the hisi-lpc driver
- Fixed and optimized hisi-lpc driver to avoid potential use-after-free
and driver unbind crash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BnY2
-----END PGP SIGNATURE-----
Merge tag 'hisi-fixes-for-5.3' of git://github.com/hisilicon/linux-hisi into arm/fixes
Hisilicon fixes for v5.3-rc
- Fixed RCU usage in logical PIO
- Added a function to unregister a logical PIO range in logical PIO
to support the fixes in the hisi-lpc driver
- Fixed and optimized hisi-lpc driver to avoid potential use-after-free
and driver unbind crash
* tag 'hisi-fixes-for-5.3' of git://github.com/hisilicon/linux-hisi:
bus: hisi_lpc: Add .remove method to avoid driver unbind crash
bus: hisi_lpc: Unregister logical PIO range to avoid potential use-after-free
lib: logic_pio: Add logic_pio_unregister_range()
lib: logic_pio: Avoid possible overlap for unregistering regions
lib: logic_pio: Fix RCU usage
Link: https://lore.kernel.org/r/5D562335.7000902@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The noencrypt flag was intended to be set if the "frame was received
unencrypted" according to include/uapi/linux/nl80211.h. However, the
current behavior is opposite of this.
Cc: stable@vger.kernel.org
Fixes: 018f6fbf54 ("mac80211: Send control port frames over nl80211")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190827224120.14545-3-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_deliver_skb_to_local_stack intercepts EAPoL frames if
mac80211 is configured to do so and forwards the contents over nl80211.
During this process some additional data is also forwarded, including
whether the frame was received encrypted or not. Unfortunately just
prior to the call to ieee80211_deliver_skb_to_local_stack, skb->cb is
cleared, resulting in incorrect data being exposed over nl80211.
Fixes: 018f6fbf54 ("mac80211: Send control port frames over nl80211")
Cc: stable@vger.kernel.org
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190827224120.14545-2-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to use a different firmware for C0 versions of killer Qu NICs.
Add structures for them and handle them in the if block that detects
C0 revisions.
Additionally, instead of having an inclusive check for QnJ devices,
make the selection exclusive, so that switching to QnJ is the
exception, not the default. This prevents us from having to add all
the non-QnJ cards to an exclusion list. To do so, only go into the
QnJ block if the device has an RF ID type HR and HW revision QnJ.
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190821171732.2266-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If 'fq' qdisc is used and a program has requested timestamps,
skb->tstamp needs to be cleared, else fq will treat these as
'transmit time'.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
lib/devres.c, which implements devm_ioremap_resource(), is only built
when CONFIG_HAS_IOMEM is set/enabled, so MTD_HYPERBUS should depend
on HAS_IOMEM. Fixes a build error and a Kconfig warning (as seen on
UML builds):
WARNING: unmet direct dependencies detected for MTD_COMPLEX_MAPPINGS
Depends on [n]: MTD [=m] && HAS_IOMEM [=n]
Selected by [m]:
- MTD_HYPERBUS [=m] && MTD [=m]
ERROR: "devm_ioremap_resource" [drivers/mtd/hyperbus/hyperbus-core.ko] undefined!
Fixes: dcc7d3446a ("mtd: Add support for HyperBus memory devices")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-mtd@lists.infradead.org
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A similar workaround for the suspend/resume problem is needed for yet
another ASUS machines, P6X models. Like the previous fix, the BIOS
doesn't provide the standard DMI_SYS_* entry, so again DMI_BOARD_*
entries are used instead.
Reported-and-tested-by: SteveM <swm@swm1.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: flower: fix bugs in merge tunnel encap code
John says:
There are few bugs in the merge encap code that have come to light with
recent driver changes. Effectively, flow bind callbacks were being
registered twice when using internal ports (new 'busy' code triggers
this). There was also an issue with neighbour notifier messages being
ignored for internal ports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent code changes to NFP allowed the offload of neighbour entries to FW
when the next hop device was an internal port. This allows for offload of
tunnel encap when the end-point IP address is applied to such a port.
Unfortunately, the neighbour event handler still rejects events that are
not associated with a repr dev and so the firmware neighbour table may get
out of sync for internal ports.
Fix this by allowing internal port neighbour events to be correctly
processed.
Fixes: 45756dfeda ("nfp: flower: allow tunnels to output to internal port")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal port TC offload is implemented through user-space applications
(such as OvS) by adding filters at egress via TC clsact qdiscs. Indirect
block offload support in the NFP driver accepts both ingress qdisc binds
and egress binds if the device is an internal port. However, clsact sends
bind notification for both ingress and egress block binds which can lead
to the driver registering multiple callbacks and receiving multiple
notifications of new filters.
Fix this by rejecting ingress block bind callbacks when the port is
internal and only adding filter callbacks for egress binds.
Fixes: 4d12ba4278 ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: fix side effect
v3:
Update the commit message for patch #1.
v2:
Replace patch #2 with "r8152: remove calling netif_napi_del".
v1:
The commit 0ee1f47349 ("r8152: napi hangup fix after disconnect")
add a check to avoid using napi_disable after netif_napi_del. However,
the commit ffa9fec30c ("r8152: set RTL8152_UNPLUG only for real
disconnection") let the check useless.
Therefore, I revert commit 0ee1f47349 ("r8152: napi hangup fix
after disconnect") first, and add another patch to fix it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary use of netif_napi_del. This also avoids to call
napi_disable() after netif_napi_del().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0ee1f47349.
The commit 0ee1f47349 ("r8152: napi hangup fix after
disconnect") adds a check about RTL8152_UNPLUG to determine
if calling napi_disable() is invalid in rtl8152_close(),
when rtl8152_disconnect() is called. This avoids to use
napi_disable() after calling netif_napi_del().
Howver, commit ffa9fec30c ("r8152: set RTL8152_UNPLUG
only for real disconnection") causes that RTL8152_UNPLUG
is not always set when calling rtl8152_disconnect().
Therefore, I have to revert commit 0ee1f47349 ("r8152:
napi hangup fix after disconnect"), first. And submit
another patch to fix it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP associates tx timestamp requests with a byte in the bytestream.
If merging skbs in tcp_mtu_probe, migrate the tstamp request.
Similar to MSG_EOR, do not allow moving a timestamp from any segment
in the probe but the last. This to avoid merging multiple timestamps.
Tested with the packetdrill script at
https://github.com/wdebruij/packetdrill/commits/mtu_probe-1
Link: http://patchwork.ozlabs.org/patch/1143278/#2232897
Fixes: 4ed2d765df ("net-timestamp: TCP timestamping")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Action sample doesn't properly handle psample_group pointer in overwrite
case. Following issues need to be fixed:
- In tcf_sample_init() function RCU_INIT_POINTER() is used to set
s->psample_group, even though we neither setting the pointer to NULL, nor
preventing concurrent readers from accessing the pointer in some way.
Use rcu_swap_protected() instead to safely reset the pointer.
- Old value of s->psample_group is not released or deallocated in any way,
which results resource leak. Use psample_group_put() on non-NULL value
obtained with rcu_swap_protected().
- The function psample_group_put() that released reference to struct
psample_group pointed by rcu-pointer s->psample_group doesn't respect rcu
grace period when deallocating it. Extend struct psample_group with rcu
head and use kfree_rcu when freeing it.
Fixes: 5c5670fae4 ("net/sched: Introduce sample tc action")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the ibmvnic driver will not schedule device resets
if the device is being removed, but does not check the device
state before the reset is actually processed. This leads to a race
where a reset is scheduled with a valid device state but is
processed after the driver has been removed, resulting in an oops.
Fix this by checking the device state before processing a queued
reset event.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pfn_valid can be wrong when parsing a invalid pfn whose phys address
exceeds BITS_PER_LONG as the MSB will be trimed when shifted.
The issue originally arise from bellowing call stack, which corresponding to
an access of the /proc/kpageflags from userspace with a invalid pfn parameter
and leads to kernel panic.
[46886.723249] c7 [<c031ff98>] (stable_page_flags) from [<c03203f8>]
[46886.723264] c7 [<c0320368>] (kpageflags_read) from [<c0312030>]
[46886.723280] c7 [<c0311fb0>] (proc_reg_read) from [<c02a6e6c>]
[46886.723290] c7 [<c02a6e24>] (__vfs_read) from [<c02a7018>]
[46886.723301] c7 [<c02a6f74>] (vfs_read) from [<c02a778c>]
[46886.723315] c7 [<c02a770c>] (SyS_pread64) from [<c0108620>]
(ret_fast_syscall+0x0/0x28)
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Currently, various virtual memory areas of Linux RISC-V are organized
in increasing order of their virtual addresses is as follows:
1. User space area (This is lowest area and starts at 0x0)
2. FIXMAP area
3. VMALLOC area
4. Kernel area (This is highest area and starts at PAGE_OFFSET)
The maximum size of user space aread is represented by TASK_SIZE.
On RV32 systems, TASK_SIZE is defined as VMALLOC_START which causes the
user space area to overlap the FIXMAP area. This allows user space apps
to potentially corrupt the FIXMAP area and kernel OF APIs will crash
whenever they access corrupted FDT in the FIXMAP area.
On RV64 systems, TASK_SIZE is set to fixed 256GB and no other areas
happen to overlap so we don't see any FIXMAP area corruptions.
This patch fixes FIXMAP area corruption on RV32 systems by setting
TASK_SIZE to FIXADDR_START. We also move FIXADDR_TOP, FIXADDR_SIZE,
and FIXADDR_START defines to asm/pgtable.h so that we can avoid cyclic
header includes.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Only the first fragment in a datagram contains the L4 headers. When the
Open vSwitch module parses a packet, it always sets the IP protocol
field in the key, but can only set the L4 fields on the first fragment.
The original behavior would not clear the L4 portion of the key, so
garbage values would be sent in the key for "later" fragments. This
patch clears the L4 fields in that circumstance to prevent sending those
garbage values as part of the upcall.
Signed-off-by: Justin Pettit <jpettit@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IP fragments are reassembled before being sent to conntrack, the
key from the last fragment is used. Unless there are reordering
issues, the last fragment received will not contain the L4 ports, so the
key for the reassembled datagram won't contain them. This patch updates
the key once we have a reassembled datagram.
The handle_fragments() function works on L3 headers so we pull the L3/L4
flow key update code from key_extract into a new function
'key_extract_l3l4'. Then we add a another new function
ovs_flow_key_update_l3l4() and export it so that it is accessible by
handle_fragments() for conntrack packet reassembly.
Co-authored-by: Justin Pettit <jpettit@ovn.org>
Signed-off-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that 'TCQ_F_CPUSTATS' bit can be cleared, depending on the value of
'TCQ_F_NOLOCK' bit in the parent qdisc, we need to be sure that per-cpu
counters are present when 'reset()' is called for pfifo_fast qdiscs.
Otherwise, the following script:
# tc q a dev lo handle 1: root htb default 100
# tc c a dev lo parent 1: classid 1:100 htb \
> rate 95Mbit ceil 100Mbit burst 64k
[...]
# tc f a dev lo parent 1: protocol arp basic classid 1:100
[...]
# tc q a dev lo parent 1:100 handle 100: pfifo_fast
[...]
# tc q d dev lo root
can generate the following splat:
Unable to handle kernel paging request at virtual address dfff2c01bd148000
Mem abort info:
ESR = 0x96000004
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
[dfff2c01bd148000] address between user and kernel address ranges
Internal error: Oops: 96000004 [#1] SMP
[...]
pstate: 80000005 (Nzcv daif -PAN -UAO)
pc : pfifo_fast_reset+0x280/0x4d8
lr : pfifo_fast_reset+0x21c/0x4d8
sp : ffff800d09676fa0
x29: ffff800d09676fa0 x28: ffff200012ee22e4
x27: dfff200000000000 x26: 0000000000000000
x25: ffff800ca0799958 x24: ffff1001940f332b
x23: 0000000000000007 x22: ffff200012ee1ab8
x21: 0000600de8a40000 x20: 0000000000000000
x19: ffff800ca0799900 x18: 0000000000000000
x17: 0000000000000002 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: ffff1001b922e6e2
x11: 1ffff001b922e6e1 x10: 0000000000000000
x9 : 1ffff001b922e6e1 x8 : dfff200000000000
x7 : 0000000000000000 x6 : 0000000000000000
x5 : 1fffe400025dc45c x4 : 1fffe400025dc357
x3 : 00000c01bd148000 x2 : 0000600de8a40000
x1 : 0000000000000007 x0 : 0000600de8a40004
Call trace:
pfifo_fast_reset+0x280/0x4d8
qdisc_reset+0x6c/0x370
htb_reset+0x150/0x3b8 [sch_htb]
qdisc_reset+0x6c/0x370
dev_deactivate_queue.constprop.5+0xe0/0x1a8
dev_deactivate_many+0xd8/0x908
dev_deactivate+0xe4/0x190
qdisc_graft+0x88c/0xbd0
tc_get_qdisc+0x418/0x8a8
rtnetlink_rcv_msg+0x3a8/0xa78
netlink_rcv_skb+0x18c/0x328
rtnetlink_rcv+0x28/0x38
netlink_unicast+0x3c4/0x538
netlink_sendmsg+0x538/0x9a0
sock_sendmsg+0xac/0xf8
___sys_sendmsg+0x53c/0x658
__sys_sendmsg+0xc8/0x140
__arm64_sys_sendmsg+0x74/0xa8
el0_svc_handler+0x164/0x468
el0_svc+0x10/0x14
Code: 910012a0 92400801 d343fc03 11000c21 (38fb6863)
Fix this by testing the value of 'TCQ_F_CPUSTATS' bit in 'qdisc->flags',
before dereferencing 'qdisc->cpu_qstats'.
Changes since v1:
- coding style improvements, thanks to Stefano Brivio
Fixes: 8a53e616de ("net: sched: when clearing NOLOCK, clear TCQ_F_CPUSTATS, too")
CC: Paolo Abeni <pabeni@redhat.com>
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yash Shah says:
====================
macb: Update ethernet compatible string for SiFive FU540
This patch series renames the compatible property to a more appropriate
string. The patchset is based on Linux-5.3-rc6 and tested on SiFive
Unleashed board
Change history:
Since v1:
- Dropped PATCH3 because it's already merged
- Change the reference url in the patch descriptions to point to a
'lore.kernel.org' link instead of 'lkml.org'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the compatibility string for SiFive FU540-C000 as per the new
string updated in the binding doc.
Reference:
https://lore.kernel.org/netdev/CAJ2_jOFEVZQat0Yprg4hem4jRrqkB72FKSeQj4p8P5KA-+rgww@mail.gmail.com/
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Tested-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per the discussion with Nicolas Ferre[0], rename the compatible property
to a more appropriate and specific string.
[0] https://lore.kernel.org/netdev/CAJ2_jOFEVZQat0Yprg4hem4jRrqkB72FKSeQj4p8P5KA-+rgww@mail.gmail.com/
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scom driver currently fails out of operations if certain system
errors are flagged in the status register; system checkstop, special
attention, or recoverable error. These errors won't impact the ability
of the scom engine to perform operations, so the driver should continue
under these conditions.
Also, don't do a PIB reset for these conditions, since it won't help.
Fixes: 6b293258cd ("fsi: scom: Major overhaul")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190827041249.13381-1-jk@ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Francois reported that VMware balloon gets stuck after a balloon reset,
when the VMCI doorbell is removed. A similar error can occur when the
balloon driver is removed with the following splat:
[ 1088.622000] INFO: task modprobe:3565 blocked for more than 120 seconds.
[ 1088.622035] Tainted: G W 5.2.0 #4
[ 1088.622087] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1088.622205] modprobe D 0 3565 1450 0x00000000
[ 1088.622210] Call Trace:
[ 1088.622246] __schedule+0x2a8/0x690
[ 1088.622248] schedule+0x2d/0x90
[ 1088.622250] schedule_timeout+0x1d3/0x2f0
[ 1088.622252] wait_for_completion+0xba/0x140
[ 1088.622320] ? wake_up_q+0x80/0x80
[ 1088.622370] vmci_resource_remove+0xb9/0xc0 [vmw_vmci]
[ 1088.622373] vmci_doorbell_destroy+0x9e/0xd0 [vmw_vmci]
[ 1088.622379] vmballoon_vmci_cleanup+0x6e/0xf0 [vmw_balloon]
[ 1088.622381] vmballoon_exit+0x18/0xcc8 [vmw_balloon]
[ 1088.622394] __x64_sys_delete_module+0x146/0x280
[ 1088.622408] do_syscall_64+0x5a/0x130
[ 1088.622410] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1088.622415] RIP: 0033:0x7f54f62791b7
[ 1088.622421] Code: Bad RIP value.
[ 1088.622421] RSP: 002b:00007fff2a949008 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ 1088.622426] RAX: ffffffffffffffda RBX: 000055dff8b55d00 RCX: 00007f54f62791b7
[ 1088.622426] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 000055dff8b55d68
[ 1088.622427] RBP: 000055dff8b55d00 R08: 00007fff2a947fb1 R09: 0000000000000000
[ 1088.622427] R10: 00007f54f62f5cc0 R11: 0000000000000206 R12: 000055dff8b55d68
[ 1088.622428] R13: 0000000000000001 R14: 000055dff8b55d68 R15: 00007fff2a94a3f0
The cause for the bug is that when the "delayed" doorbell is invoked, it
takes a reference on the doorbell entry and schedules work that is
supposed to run the appropriate code and drop the doorbell entry
reference. The code ignores the fact that if the work is already queued,
it will not be scheduled to run one more time. As a result one of the
references would not be dropped. When the code waits for the reference
to get to zero, during balloon reset or module removal, it gets stuck.
Fix it. Drop the reference if schedule_work() indicates that the work is
already queued.
Note that this bug got more apparent (or apparent at all) due to
commit ce664331b2 ("vmw_balloon: VMCI_DOORBELL_SET does not check status").
Fixes: 83e2ec765b ("VMCI: doorbell implementation.")
Reported-by: Francois Rigault <rigault.francois@gmail.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Cc: Adit Ranadive <aditr@vmware.com>
Cc: Alexios Zavras <alexios.zavras@intel.com>
Cc: Vishnu DASA <vdasa@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20190820202638.49003-1-namit@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of a disconnect an ongoing flush() has to be made fail.
Nevertheless we cannot be sure that any pending URB has already
finished, so although they will never succeed, they still must
not be touched.
The clean solution for this is to check for WDM_IN_USE
and WDM_DISCONNECTED in flush(). There is no point in ever
clearing WDM_IN_USE, as no further writes make sense.
The issue is as old as the driver.
Fixes: afba937e54 ("USB: CDC WDM driver")
Reported-by: syzbot+d232cca6ec42c2edb3fc@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190827103436.21143-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chunyan Zhang