Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
This cycle we have small update for:
- updates to xilinx and zynqmp dma controllers
- update reside calculation for rcar controller
- more RSTify fixes for documentation
- Add support for race free transfer termination and updating
for users for that
- Support for new rev of hidma with addition new APIs to
get device match data in ACPI/OF
- Random updates to bunch of other drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7bH/
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time is smallish update with updates mainly to drivers:
- updates to xilinx and zynqmp dma controllers
- update reside calculation for rcar controller
- more RSTify fixes for documentation
- add support for race free transfer termination and updating for
users for that
- support for new rev of hidma with addition new APIs to get device
match data in ACPI/OF
- random updates to bunch of other drivers"
* tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (47 commits)
dmaengine: dmatest: fix container_of member in dmatest_callback
dmaengine: stm32-dmamux: Remove unnecessary platform_get_resource() error check
dmaengine: sprd: statify 'sprd_dma_prep_dma_memcpy'
dmaengine: qcom_hidma: simplify DT resource parsing
dmaengine: xilinx_dma: Free BD consistent memory
dmaengine: xilinx_dma: Fix warning variable prev set but not used
dmaengine: xilinx_dma: properly configure the SG mode bit in the driver for cdma
dmaengine: doc: format struct fields using monospace
dmaengine: doc: fix bullet list formatting
dmaengine: ti-dma-crossbar: Fix event mapping for TPCC_EVT_MUX_60_63
dmaengine: cppi41: Fix channel queues array size check
dmaengine: imx-sdma: Add MODULE_FIRMWARE
dmaengine: xilinx_dma: Fix typos
dmaengine: xilinx_dma: Differentiate probe based on the ip type
dmaengine: xilinx_dma: fix style issues from checkpatch
dmaengine: xilinx_dma: Fix kernel doc warnings
dmaengine: xilinx_dma: Fix race condition in the driver for multiple descriptor scenario
dmaeninge: xilinx_dma: Fix bug in multiple frame stores scenario in vdma
dmaengine: xilinx_dma: Check for channel idle state before submitting dma descriptor
dmaengine: zynqmp_dma: Fix race condition in the probe
...
Pull siginfo cleanups from Eric Biederman:
"Long ago when 2.4 was just a testing release copy_siginfo_to_user was
made to copy individual fields to userspace, possibly for efficiency
and to ensure initialized values were not copied to userspace.
Unfortunately the design was complex, it's assumptions unstated, and
humans are fallible and so while it worked much of the time that
design failed to ensure unitialized memory is not copied to userspace.
This set of changes is part of a new design to clean up siginfo and
simplify things, and hopefully make the siginfo handling robust enough
that a simple inspection of the code can be made to ensure we don't
copy any unitializied fields to userspace.
The design is to unify struct siginfo and struct compat_siginfo into a
single definition that is shared between all architectures so that
anyone adding to the set of information shared with struct siginfo can
see the whole picture. Hopefully ensuring all future si_code
assignments are arch independent.
The design is to unify copy_siginfo_to_user32 and
copy_siginfo_from_user32 so that those function are complete and cope
with all of the different cases documented in signinfo_layout. I don't
think there was a single implementation of either of those functions
that was complete and correct before my changes unified them.
The design is to introduce a series of helpers including
force_siginfo_fault that take the values that are needed in struct
siginfo and build the siginfo structure for their callers. Ensuring
struct siginfo is built correctly.
The remaining work for 4.17 (unless someone thinks it is post -rc1
material) is to push usage of those helpers down into the
architectures so that architecture specific code will not need to deal
with the fiddly work of intializing struct siginfo, and then when
struct siginfo is guaranteed to be fully initialized change copy
siginfo_to_user into a simple wrapper around copy_to_user.
Further there is work in progress on the issues that have been
documented requires arch specific knowledge to sort out.
The changes below fix or at least document all of the issues that have
been found with siginfo generation. Then proceed to unify struct
siginfo the 32 bit helpers that copy siginfo to and from userspace,
and generally clean up anything that is not arch specific with regards
to siginfo generation.
It is a lot but with the unification you can of siginfo you can
already see the code reduction in the kernel"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (45 commits)
signal/memory-failure: Use force_sig_mceerr and send_sig_mceerr
mm/memory_failure: Remove unused trapno from memory_failure
signal/ptrace: Add force_sig_ptrace_errno_trap and use it where needed
signal/powerpc: Remove unnecessary signal_code parameter of do_send_trap
signal: Helpers for faults with specialized siginfo layouts
signal: Add send_sig_fault and force_sig_fault
signal: Replace memset(info,...) with clear_siginfo for clarity
signal: Don't use structure initializers for struct siginfo
signal/arm64: Better isolate the COMPAT_TASK portion of ptrace_hbptriggered
ptrace: Use copy_siginfo in setsiginfo and getsiginfo
signal: Unify and correct copy_siginfo_to_user32
signal: Remove the code to clear siginfo before calling copy_siginfo_from_user32
signal: Unify and correct copy_siginfo_from_user32
signal/blackfin: Remove pointless UID16_SIGINFO_COMPAT_NEEDED
signal/blackfin: Move the blackfin specific si_codes to asm-generic/siginfo.h
signal/tile: Move the tile specific si_codes to asm-generic/siginfo.h
signal/frv: Move the frv specific si_codes to asm-generic/siginfo.h
signal/ia64: Move the ia64 specific si_codes to asm-generic/siginfo.h
signal/powerpc: Remove redefinition of NSIGTRAP on powerpc
signal: Move addr_lsb into the _sigfault union for clarity
...
A very busy release for regmap, all fairly specialist stuff but useful:
- Support for disabling locking from Bartosz Golaszewski, allowing
users that handle their own locking to save some overhead.
- Support for hwspinlocks in syscons in MFD from Baolin Wang, this is
going through the regmap tree since the first users turned up some
some cases that needed interface tweaks with 0 being used as a syscon
identifier.
- Support for devices with no read or write flag from Andrew F. Davis.
- Basic support for devices on SoundWire buses from Vinod Koul.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlpvTfYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Cd8B/4zeYHL73moxvAxAH/99HGVCHQHcR4k
hdLaGHs8JN5ZLoNCqixFdkffsdBM2H06JPOnBZMHHcb5Pf7KL3OEgPNeiMUpzxUL
0EcXoZiJz0HzRVwi6M9nt3Bv41rD5+v9nS6oolsqbU1b6w5ofZQ7ENeN+nhxLk54
Wy8avQ3VDmiKsSAAXDMEA6i58Zz7dT1ibyyOcYGyEdt7iFOL8d0aM4c3cAGHfL+E
Ss9/dyeY/8glLDy+rxp5hZHkLY7FKFDQcD1/FSR26DHslc0Swa9mn/0SmhF0pQWe
RVEn63b4B5iT0E8brlWHwNh466jT6+fyJKzYDzEM+v1RP4qUmluFubjK
=X/P5
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A very busy release for regmap, all fairly specialist stuff but
useful:
- Support for disabling locking from Bartosz Golaszewski, allowing
users that handle their own locking to save some overhead.
- Support for hwspinlocks in syscons in MFD from Baolin Wang, this is
going through the regmap tree since the first users turned up some
some cases that needed interface tweaks with 0 being used as a
syscon identifier.
- Support for devices with no read or write flag from Andrew F.
Davis.
- Basic support for devices on SoundWire buses from Vinod Koul"
* tag 'regmap-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
mfd: syscon: Add hardware spinlock support
regmap: Allow empty read/write_flag_mask
regcache: flat: Un-inline index lookup from cache access
regmap: Add SoundWire bus support
regmap: Add one flag to indicate if a hwlock should be used
regmap: debugfs: document why we don't create the debugfs entries
regmap: debugfs: emit a debug message when locking is disabled
regmap: use proper part of work_buf for storing val
regmap: potentially duplicate the name string stored in regmap
regmap: Disable debugfs when locking is disabled
regmap: rename regmap_lock_unlock_empty() to regmap_lock_unlock_none()
regmap: allow to disable all locking mechanisms
regmap: Remove the redundant config to select hwspinlock
Today 4 architectures set ARCH_SUPPORTS_MEMORY_FAILURE (arm64, parisc,
powerpc, and x86), while 4 other architectures set __ARCH_SI_TRAPNO
(alpha, metag, sparc, and tile). These two sets of architectures do
not interesect so remove the trapno paramater to remove confusion.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Implement a new helper function fwnode_get_next_available_child_node(),
which enables obtaining next enabled child fwnode, which
works on a similar basis to OF's of_get_next_available_child().
This commit also introduces a macro, thanks to which it is
possible to iterate over the available fwnodes, using the
new function described above.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now there were two very similar functions allowing
to get Linux IRQ number from ACPI handle (acpi_irq_get())
and OF node (of_irq_get()). The first one appeared to be used
only as a subroutine of platform_irq_get(), which (in the generic
code) limited IRQ obtaining from _CRS method only to nodes
associated to kernel's struct platform_device.
This patch introduces a new helper routine - fwnode_irq_get(),
which allows to get the IRQ number directly from the fwnode
to be used as common for OF/ACPI worlds. It is usable not
only for the parents fwnodes, but also for the child nodes
comprising their own _CRS methods with interrupts description.
In order to be able o satisfy compilation with !CONFIG_ACPI
and also simplify the new code, introduce a helper macro
(ACPI_HANDLE_FWNODE), with which it is possible to reach
an ACPI handle directly from its fwnode.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now there were two almost identical functions for
obtaining network PHY mode - of_get_phy_mode() and,
more generic, device_get_phy_mode(). However it is not uncommon,
that the network interface is represented as a child
of the actual controller, hence it is not associated
directly to any struct device, required by the latter
routine.
This commit allows for getting the PHY mode for
children nodes in the ACPI world by introducing a new function -
fwnode_get_phy_mode(). This commit also changes
device_get_phy_mode() routine to be its wrapper, in order
to prevent unnecessary duplication.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now there were two almost identical functions for
obtaining MAC address - of_get_mac_address() and, more generic,
device_get_mac_address(). However it is not uncommon,
that the network interface is represented as a child
of the actual controller, hence it is not associated
directly to any struct device, required by the latter
routine.
This commit allows for getting the MAC address for
children nodes in the ACPI world by introducing a new function -
fwnode_get_mac_address(). This commit also changes
device_get_mac_address() routine to be its wrapper, in order
to prevent unnecessary duplication.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pm-core: (29 commits)
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
PM: i2c-designware-platdrv: Optimize power management
PM: i2c-designware-platdrv: Use DPM_FLAG_SMART_PREPARE
PM / mfd: intel-lpss: Use DPM_FLAG_SMART_SUSPEND
PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports
PM / wakeup: Add device_set_wakeup_path() helper to control wakeup path
PM / core: Assign the wakeup_path status flag in __device_prepare()
PM / wakeup: Do not fail dev_pm_attach_wake_irq() unnecessarily
PM / core: Direct DPM_FLAG_LEAVE_SUSPENDED handling
PM / core: Direct DPM_FLAG_SMART_SUSPEND optimization
PM / core: Add helpers for subsystem callback selection
PM / wakeup: Drop redundant check from device_init_wakeup()
PM / wakeup: Drop redundant check from device_set_wakeup_enable()
PM / wakeup: only recommend "call"ing device_init_wakeup() once
...
The pm_runtime_force_suspend|resume() helpers currently requires the device
to at some level (PM domain, bus, etc), have the ->runtime_suspend|resume()
callbacks assigned for it, else -ENOSYS is returned as an error.
However, there are no reason for this requirement, so let's simply remove
it by allowing these callbacks to be NULL.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify pm_runtime_need_not_resume() to make it avoid taking
power.child_count for devices with power.ignore_children which
is consistent with the runtime PM usage of these fields.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
One of the limitations of pm_runtime_force_suspend/resume() is that
if a parent driver wants to use these functions, all of its child
drivers generally have to do that too because of the parent usage
counter manipulations necessary to get the correct state of the parent
during system-wide transitions to the working state (system resume).
However, that limitation turns out to be artificial, so remove it.
Namely, pm_runtime_force_suspend() only needs to update the children
counter of its parent (if there's is a parent) when the device can
stay in suspend after the subsequent system resume transition, as
that counter is correct already otherwise. Now, if the parent's
children counter is not updated, it is not necessary to increment
the parent's usage counter in that case any more, as long as the
children counters of devices are checked along with their usage
counters in order to decide whether or not the devices may be left
in suspend after the subsequent system resume transition.
Accordingly, modify pm_runtime_force_suspend() to only call
pm_runtime_set_suspended() for devices whose usage and children
counters are at the "no references" level (the runtime PM status
of the device needs to be updated to "suspended" anyway in case
this function is called once again for the same device during the
transition under way), drop the parent usage counter incrementation
from it and update pm_runtime_force_resume() to compensate for these
changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
There are problems with calling pm_runtime_force_suspend/resume()
to "stop" and "start" devices in genpd_finish_suspend() and
genpd_resume_noirq() (and in analogous hibernation-specific genpd
callbacks) after commit 122a22377a (PM / Domains: Stop/start
devices during system PM suspend/resume in genpd) as those routines
do much more than just "stopping" and "starting" devices (which was
the stated purpose of that commit) unnecessarily and may not play
well with system-wide PM driver callbacks.
First, consider the pm_runtime_force_suspend() in
genpd_finish_suspend(). If the current runtime PM status of the
device is "suspended", that function most likely does the right thing
by ignoring the device, because it should have been "stopped" already
and whatever needed to be done to deactivate it shoud have been done.
In turn, if the runtime PM status of the device is "active",
genpd_runtime_suspend() is called for it (indirectly) and (1) runs
the ->runtime_suspend callback provided by the device's driver
(assuming no bus type with ->runtime_suspend of its own), (2) "stops"
the device and (3) checks if the domain can be powered down, and then
(4) the device's runtime PM status is changed to "suspended". Out of
the four actions above (1) is not necessary and it may be outright
harmful, (3) is pointless and (4) is questionable. The only
operation that needs to be carried out here is (2).
The reason why (1) is not necessary is because the system-wide
PM callbacks provided by the device driver for the transition in
question have been run and they should have taken care of the
driver's part of device suspend already. Moreover, it may be
harmful, because the ->runtime_suspend callback may want to
access the device which is partially suspended at that point
and may not be responsive. Also, system-wide PM callbacks may
have been run already (in the previous phases of the system
transition under way) for the device's parent or for its supplier
devices (if any) and the device may not be accessible because of
that.
There also is no reason to do (3), because genpd_finish_suspend()
will repeat it anyway, and (4) potentially causes confusion to ensue
during the subsequent system transition to the working state.
Consider pm_runtime_force_resume() in genpd_resume_noirq() now.
It runs genpd_runtime_resume() for all devices with runtime PM
status set to "suspended", which includes all of the devices
whose runtime PM status was changed by pm_runtime_force_suspend()
before and may include some devices already suspended when the
pm_runtime_force_suspend() was running, which may be confusing. The
genpd_runtime_resume() first tries to power up the domain, which
(again) is pointless, because genpd_resume_noirq() has done that
already. Then, it "starts" the device and runs the ->runtime_resume
callback (from the driver, say) for it. If all is well, the device
is left with the runtime PM status set to "active".
Unfortunately, running the driver's ->runtime_resume callback
before its system-wide PM callbacks and possibly before some
system-wide PM callbacks of the parent device's driver (let
alone supplier drivers) is asking for trouble, especially if
the device had been suspended before pm_runtime_force_suspend()
ran previously or if the callbacks in question expect to be run
back-to-back with their suspend-side counterparts. It also should
not be necessary, because the system-wide PM driver callbacks that
will be invoked for the device subsequently should take care of
resuming it just fine.
[Running the driver's ->runtime_resume callback in the "noirq"
phase of the transition to the working state may be problematic
even for devices whose drivers do use pm_runtime_force_resume()
in (or as) their system-wide PM callbacks if they have suppliers
other than their parents, because it may cause the supplier to
be resumed after the consumer in some cases.]
Because of the above, modify genpd as follows:
1. Change genpd_finish_suspend() to only "stop" devices with
runtime PM status set to "active" (without invoking runtime PM
callbacks for them, changing their runtime PM status and so on).
That doesn't change the handling of devices whose drivers use
pm_runtime_force_suspend/resume() in (or as) their system-wide
PM callbacks and addresses the issues described above for the
other devices.
2. Change genpd_resume_noirq() to only "start" devices with
runtime PM status set to "active" (without invoking runtime PM
callbacks for them, changing their runtime PM status and so on).
Again, that doesn't change the handling of devices whose drivers
use pm_runtime_force_suspend/resume() in (or as) their system-wide
PM callbacks and addresses the described issues for the other
devices. Devices with runtime PM status set to "suspended"
are not started with the assumption that they will be resumed
later, either by pm_runtime_force_resume() or via runtime PM.
3. Change genpd_restore_noirq() to follow genpd_resume_noirq().
That causes devices already suspended before hibernation to be
left alone (which also is the case without the change) and
avoids running the ->runtime_resume driver callback too early
for the other devices.
4. Change genpd_freeze_noirq() and genpd_thaw_noirq() in accordance
with the above modifications.
Fixes: 122a22377a (PM / Domains: Stop/start devices during system PM suspend/resume in genpd)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull x86 pti updates from Thomas Gleixner:
"This contains:
- a PTI bugfix to avoid setting reserved CR3 bits when PCID is
disabled. This seems to cause issues on a virtual machine at least
and is incorrect according to the AMD manual.
- a PTI bugfix which disables the perf BTS facility if PTI is
enabled. The BTS AUX buffer is not globally visible and causes the
CPU to fault when the mapping disappears on switching CR3 to user
space. A full fix which restores BTS on PTI is non trivial and will
be worked on.
- PTI bugfixes for EFI and trusted boot which make sure that the user
space visible page table entries have the NX bit cleared
- removal of dead code in the PTI pagetable setup functions
- add PTI documentation
- add a selftest for vsyscall to verify that the kernel actually
implements what it advertises.
- a sysfs interface to expose vulnerability and mitigation
information so there is a coherent way for users to retrieve the
status.
- the initial spectre_v2 mitigations, aka retpoline:
+ The necessary ASM thunk and compiler support
+ The ASM variants of retpoline and the conversion of affected ASM
code
+ Make LFENCE serializing on AMD so it can be used as speculation
trap
+ The RSB fill after vmexit
- initial objtool support for retpoline
As I said in the status mail this is the most of the set of patches
which should go into 4.15 except two straight forward patches still on
hold:
- the retpoline add on of LFENCE which waits for ACKs
- the RSB fill after context switch
Both should be ready to go early next week and with that we'll have
covered the major holes of spectre_v2 and go back to normality"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
x86,perf: Disable intel_bts when PTI
security/Kconfig: Correct the Documentation reference for PTI
x86/pti: Fix !PCID and sanitize defines
selftests/x86: Add test_vsyscall
x86/retpoline: Fill return stack buffer on vmexit
x86/retpoline/irq32: Convert assembler indirect jumps
x86/retpoline/checksum32: Convert assembler indirect jumps
x86/retpoline/xen: Convert Xen hypercall indirect jumps
x86/retpoline/hyperv: Convert assembler indirect jumps
x86/retpoline/ftrace: Convert ftrace assembler indirect jumps
x86/retpoline/entry: Convert entry assembler indirect jumps
x86/retpoline/crypto: Convert crypto assembler indirect jumps
x86/spectre: Add boot time option to select Spectre v2 mitigation
x86/retpoline: Add initial retpoline support
objtool: Allow alternatives to be ignored
objtool: Detect jumps to retpoline thunks
x86/pti: Make unpoison of pgd for trusted boot work for real
x86/alternatives: Fix optimize_nops() checking
sysfs/cpu: Fix typos in vulnerability documentation
x86/cpu/AMD: Use LFENCE_RDTSC in preference to MFENCE_RDTSC
...
In general, wakeup settings are not supposed to be changed during any of
the system wide PM phases. The reason is simply that it would break
guarantees provided by the PM core, to properly act on active wakeup
sources.
However, there are exceptions to when, in particular, disabling a device as
wakeup source makes sense. For example, in cases when a driver realizes
that its device is dead during system suspend. For these scenarios, we
don't need to care about acting on the wakeup source correctly, because a
dead device shouldn't deliver wakeup signals.
To this reasoning and to help users to properly manage wakeup settings,
let's print a warning in cases someone calls device_wakeup_enable() during
system sleep.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Message to be printed ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 10da65423f (PM / Domains: Call driver's noirq callbacks)
started to respect driver's noirq callbacks, but while doing that it
also introduced a few potential problems.
More precisely, in genpd_finish_suspend() and genpd_resume_noirq()
the noirq callbacks at the driver level should be invoked, no matter
of whether dev->power.wakeup_path is set or not.
Additionally, the commit in question also made genpd_resume_noirq()
to ignore the return value from pm_runtime_force_resume().
Let's fix both these issues!
Fixes: 10da65423f (PM / Domains: Call driver's noirq callbacks)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the wakeup_path status flag becomes propagated from a child
device to its parent device at __device_suspend(). This allows a driver
dealing with a parent device to act on the flag from its ->suspend()
callback.
However, in situations when the wakeup_path status flag needs to be set
from a ->suspend_late() callback, its value doesn't get propagated to the
parent by the PM core. Let's address this limitation, by also propagating
the flag at __device_suspend_late().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To make the code more consistent, let's clear the parent's direct_complete
flag along with clearing it for suppliers, instead of as currently, when
propagating the wakeup_path flag to parents.
While changing this, let's take the opportunity to rename the affected
internal functions, to make them self-explanatory. Like this:
dpm_clear_suppliers_direct_complete -> dpm_clear_superiors_direct_complete
dpm_propagate_to_parent -> dpm_propagate_wakeup_to_parent
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM core in the device_prepare() phase, resets the wakeup_path status
flag to the value of device_may_wakeup(). This means if a ->prepare() or a
->suspend() callback for the device would update the device's wakeup
setting, this doesn't become reflected in the wakeup_path status flag.
In general this isn't a problem, because wakeup settings are not supposed
to be changed (via for example calling device_set_wakeup_enable()) during
any system wide suspend/resume phase. Nevertheless there are some users,
which can be considered as legacy, that don't conform to this behaviour.
These legacy cases should be corrected, however until that is done, let's
address the issue from the PM core, by moving the assignment of the
wakeup_path status flag to the __device_suspend() phase and after the
->suspend() callback has been invoked.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Returning an error code from dev_pm_attach_wake_irq() if
device_wakeup_attach_irq() called by it returns an error is
pointless, because the wakeup source used by it may be deleted
by user space via sysfs at any time and in particular right after
dev_pm_attach_wake_irq() has returned. Moreover, it requires
the callers of dev_pm_attach_wake_irq() to create that wakeup
source via device_wakeup_enable() upfront, but that obviously is
racy with respect to the sysfs-based manipulations of it.
To avoid the race, modify device_wakeup_attach_irq() to check
that the wakeup source it is going to use is there (and return
early otherwise), make it void (as it cannot fail after that
change) and make dev_pm_attach_wake_irq() simply call it for
the device unconditionally.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All zero read and write masks in the regmap config are used to signal no
special mask is needed and the bus defaults are used. In some devices
all zero read/write masks are the special mask and bus defaults should
not be used. To signal this a new variable is added.
For example SPI often sets bit 7 in address to signal to the device a
read is requested. On TI AFE44xx parts with SPI interfaces no bit
needs to be set as registers are either read or write only and the
operation can be determined from the address only. For this case both
masks must be zero to not effect the address.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the code slightly more readable and allows for cleaner
addition of functionality in later patches.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SoundWire bus provides sdw_read() and sdw_write() APIs for Slave
devices to program the registers. Provide support in regmap for
SoundWire bus.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the meltdown/spectre problem affects several CPU architectures, it makes
sense to have common way to express whether a system is affected by a
particular vulnerability or not. If affected the way to express the
mitigation should be common as well.
Create /sys/devices/system/cpu/vulnerabilities folder and files for
meltdown, spectre_v1 and spectre_v2.
Allow architectures to override the show function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180107214913.096657732@linutronix.de
Make the PM core handle DPM_FLAG_LEAVE_SUSPENDED directly for
devices whose "noirq", "late" and "early" driver callbacks are
invoked directly by it.
Namely, make it skip all of the system-wide resume callbacks for
such devices with DPM_FLAG_LEAVE_SUSPENDED set if they are in
runtime suspend during the "noirq" phase of system-wide suspend
(or analogous) transitions or the system transition under way is
a proper suspend (rather than anything related to hibernation) and
the device's wakeup settings are compatible with runtime PM (that
is, the device cannot generate wakeup signals at all or it is
allowed to wake up the system from sleep).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make the PM core avoid invoking the "late" and "noirq" system-wide
suspend (or analogous) callbacks provided by device drivers directly
for devices with DPM_FLAG_SMART_SUSPEND set that are in runtime
suspend during the "late" and "noirq" phases of system-wide suspend
(or analogous) transitions. That is only done for devices without
any middle-layer "late" and "noirq" suspend callbacks (to avoid
confusing the middle layer if there is one).
The underlying observation is that runtime PM is disabled for devices
during the "late" and "noirq" system-wide suspend phases, so if they
remain in runtime suspend from the "late" phase forward, it doesn't
make sense to invoke the "late" and "noirq" callbacks provided by
the drivers for them (arguably, the device is already suspended and
in the right state). Thus, if the remaining driver suspend callbacks
are to be invoked directly by the core, they can be skipped.
This change really makes it possible for, say, platform device
drivers to re-use runtime PM suspend and resume callbacks by
pointing ->suspend_late and ->resume_early, respectively (and
possibly the analogous hibernation-related callback pointers too),
to them without adding any extra "is the device already suspended?"
type of checks to the callback routines, as long as they will be
invoked directly by the core.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add helper routines to find and return a suitable subsystem callback
during the "noirq" phases of system suspend/resume (or analogous)
transitions as well as during the "late" phase of system suspend and
the "early" phase of system resume (or analogous) transitions.
The helpers will be called from additional sites going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since device_wakeup_disable() checks the device's power.can_wakeup
flag, device_init_wakeup() doesn't need to do that before calling it,
so drop that redundant check from device_init_wakeup().
No intentional changes in functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Since both device_wakeup_enable() and device_wakeup_disable() check
if dev is not NULL and whether or not power.can_wakeup is set for it,
device_set_wakeup_enable() doesn't have to do that, so drop that
check from it.
No intentional changes in functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Here are 2 driver core fixes for 4.15-rc6, resolving some reported
issues.
The first is a cacheinfo fix for DT based systems to resolve a reported
issue that has been around for a while, and the other is to resolve a
regression in the kobject uevent code that showed up in 4.15-rc1.
Both have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWkjLCA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk6GACbBZ/EqSrd5w6//4okaHJLPAi8ligAoNfcBqrH
TPQycbostUcOBHUvvoUB
=MaZG
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two driver core fixes for 4.15-rc6, resolving some reported
issues.
The first is a cacheinfo fix for DT based systems to resolve a
reported issue that has been around for a while, and the other is to
resolve a regression in the kobject uevent code that showed up in
4.15-rc1.
Both have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: fix suppressing modalias in uevents delivered over netlink
drivers: base: cacheinfo: fix cache type for non-architected system cache
Since the hwlock id 0 is valid for hardware spinlock core, but now id 0
is treated as one invalid value for regmap. Thus we should add one extra
flag for regmap config to indicate if a hardware spinlock should be used,
then id 0 can be valid for regmap to request.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a follow-up to commit a5ba91c380 ("regmap: debugfs: emit a
debug message when locking is disabled"). I figured that a user may
see this message, grep the code, come to this place and he still won't
know why we actually disabled debugfs.
Add a comment explaining the reason.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently silently omit creating the debugfs entries when regmap
locking is disabled. Users may not be aware of the reason for which
regmap files don't show up in debugfs. Add a dev_dbg() message
explaining that.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
The map->work_buf is a buffer preallocated in __regmap_init() with size
allowing it to store all 3 parts of a buffer - reg, pad and val. While
reg and val parts are always properly setup before each transaction, the
pad part is left at its default value (zeros). Until it is overwritten,
that is.
_regmap_bus_read(), when calling _regmap_raw_read() uses beginning of
work_buf as a place to store data read. Usually that is fine but if
val_bits > reg_bits && pad_bits > 0, padding area of work_buf() may get
overwritten. Since padding is not zeroed before each transaction,
garbage will be used on next calls.
This patch moves the val pointer used for _regmap_raw_read() to point
to a part of work_buf intended for storing value read.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I'll admit admit it: I've written bad driver code that tries to
configure a device's wake IRQ without having called device_init_wakeup()
first. But do you really have to ask ask me twice?
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit dfea747d2a ("drivers: base: cacheinfo: support DT overrides for
cache properties") doesn't initialise the cache type if it's present
only in DT and the architecture is not aware of it. They are unified
system level cache which are generally transparent.
This patch check if the cache type is set to NOCACHE but the DT node
indicates that it's unified cache and sets the cache type accordingly.
Fixes: dfea747d2a ("drivers: base: cacheinfo: support DT overrides for cache properties")
Reported-and-tested-by: Tan Xiaojun <tanxiaojun@huawei.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we just copy over the pointer passed to regmap_init() in
the regmap config struct. To be on the safe side: duplicate the string
with kstrdup_const() so that if an unaware user passes an address to
a stack-allocated buffer, we won't crash.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recently added support for disabling the regmap internal locking left
debugfs enabled for devices with the locking disabled. This is a problem
since debugfs allows userspace to do things like initiate reads from the
hardware which will use the scratch buffers protected by the regmap locking
so could cause data corruption.
For safety address this by just disabling debugfs for these devices. That
is overly conservative since some of the debugfs files just read internal
data structures but it's much simpler to implmement and less likely to
lead to problems with tooling that works with debugfs.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Minor naming convention tweak.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an OF/ACPI function to obtain the driver data. We want to hide
OF/ACPI details from the device drivers and abstract following the device
family of functions.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Make the PM core call dev_pm_skip_next_resume_phases() to skip the
"early resume" and "resume" phases of system-wide transitions to the
working state for a given device instead of clearing the relevant
status bits for it directly.
No intentional changes in functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The file was converted from print_fn_descriptor_symbol()
to %pF some time ago (c80cfb0406 "vsprintf: use new
vsprintf symbolic function pointer format"). kallsyms does
not seem to be needed anymore.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds