temp_crit.name and temp_input.name have a length of 16 bytes. Using
THERMAL_NAME_LENGTH (20) as length parameter for snprintf() may result in
out-of-bounds memory accesses. Replace it with sizeof().
Addresses Coverity #115679
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
we need to go over all the thermal_instance list of a cooling device
to decide which cooling state to put the cooling device to.
But at this time, as a cooling device may be referenced in multiple
thermal zones, we need to lock the list first in case
another thermal zone is updating this cooling device.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
Remove thermal_zone_device_passive(). And use
thermal_zone_trip_update() and thermal_zone_do_update()
for both active and passive cooling.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
This fixes the problem that a cooling device may be referenced by
by multiple trip points in multiple thermal zones.
With this patch, we have two stages for updating a thermal zone,
1. check if a thermal_instance needs to be updated or not
2. update the cooling device, based on the target cooling state
of all its instances.
Note that, currently, the cooling device is set to the deepest
cooling state required.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
List thermal_instance in thermal_cooling_device so that
cooling device can know the cooling state requirement
of all the thermal instances.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
thermal_instance should be referenced by both thermal zone devices
and thermal cooling devices.
Rename thermal_instance.node to thermal_instance.tz_node in this patch
and thermal_instanace.cdev_node will be introduced in next patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
Rename thermal_zone_device.cooling_devices
to thermal_zone_device.thermal_instances
thermal_zone_device.cooling_devices is not accurate
as this is a list for thermal instances, rather than cooling devices.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
This struct is used to describe the behavior for a thermal
cooling device on a certain trip point for a certain thremal zone.
thermal_cooling_device_instance is not accurate, as a cooling device
can be used for more than one trip point in one thermal zone device.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
This function is used to update the cooling state of
all the cooling devices that are bound to an active trip point.
This will be used for passive cooling as well, in the future patches.
as both active and passive cooling can share the same algorithm,
which is
1. if the temperature is higher than a trip point,
a. if the trend is THERMAL_TREND_RAISING, use higher cooling
state for this trip point
b. if the trend is THERMAL_TREND_DROPPING, use lower cooling
state for this trip point
2. if the temperature is lower than a trip point, use lower
cooling state for this trip point.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
Remove tc1/tc2 in generic thermal layer.
.get_trend() callback starts to take effect from this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Valentin, Eduardo <eduardo.valentin@ti.com>
According to ACPI spec, tc1 and tc2 are used by OSPM
to anticipate the temperature trends.
We introduced the same concept to the generic thermal layer
for passive cooling, but now it seems that these values
are hard to be used on other platforms.
So We introduce .get_trend() as a more general solution.
For the platform thermal drivers that have their own way to
anticipate the temperature trends, they should provide
their own .get_trend() callback.
Or else, we will calculate the temperature trends by simply
comparing the current temperature and the cached previous
temperature reading.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Valentin, Eduardo <eduardo.valentin@ti.com>
set upper and lower limits when binding
a thermal cooling device to a thermal zone device.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
As the active cooling devices can have multiple cooling states,
we may want only several cooling states for a certain trip point,
and other cooling states for other active trip points.
To do this, we should be able to describe the cooling device
behavior for a certain trip point, rather than for the entire thermal zone.
And when updating thermal zone, we need to check the upper and lower limit
to make sure the cooling device is set to the proper cooling state.
Note that this patch will not bring any different behavior as
upper limit is set to max_state and lower limit is set to 0
in this patch, for now.
Next patch will set these to real values.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
This is because general active cooling devices, like fans,
may have multiple speeds, which can be mapped to different cooling states.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Valentin, Eduardo <eduardo.valentin@ti.com>
Pull OLPC platform updates from Andres Salomon:
"These move the OLPC Embedded Controller driver out of
arch/x86/platform and into drivers/platform/olpc.
OLPC machines are now ARM-based (which means lots of x86 and ARM
changes), but are typically pretty self-contained.. so it makes more
sense to go through a separate OLPC tree after getting the appropriate
review/ACKs."
* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
x86: OLPC: move s/r-related EC cmds to EC driver
Platform: OLPC: move global variables into priv struct
Platform: OLPC: move debugfs support from x86 EC driver
x86: OLPC: switch over to using new EC driver on x86
Platform: OLPC: add a suspended flag to the EC driver
Platform: OLPC: turn EC driver into a platform_driver
Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
drivers: OLPC: update various drivers to include olpc-ec.h
Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver
This branch contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the branch
into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xb8w
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
"This contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the
branch into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: Kirkwood: Replace mrvl with marvell
ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
ARM: Kirkwood: Describe Dreamplug LEDs in DT.
ARM: Kirkwood: Describe iConnects LEDs in DT.
ARM: Kirkwood: Describe iConnects temperature sensor in DT.
ARM: Kirkwood: Describe IB62x0 LEDs in DT.
ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
ARM: Kirkwood: Use DT to configure SATA device.
ARM: kirkwood: use devicetree for SPI on dreamplug
ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
ARM: Kirkwood: Add basic device tree support for QNAP TS219.
ATA: sata_mv: Add device tree support
ARM: Orion: DTify the watchdog timer.
ARM: Orion: Add arch support needed for I2C via DT.
ARM: kirkwood: use devicetree for orion-spi
...
Conflicts:
drivers/watchdog/orion_wdt.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlAaIN8ACgkQGkmNcg7/o7gpMgCgtmCJeUrSCc/eVKGy5ik1BPnC
3DAAoLdqCJflwx4mrN48kkXQj9SA4Xko
=Y6yl
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
sh: explicitly include sh_dma.h in setup-sh7722.c
sh: ecovec: care CN5 VBUS if USB host mode
sh: sh7724: fixup renesas_usbhs clock settings
sh: intc: initial irqdomain support.
sh: pfc: Fix up init ordering mess.
serial: sh-sci: fix compilation breakage, when DMA is enabled
dmaengine: shdma: restore partial transfer calculation
sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
sh: Fix up recursive fault in oops with unset TTB.
sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
sh: select the fixed regulator driver on several boards
sh: ecovec: switch MMC power control to regulators
sh: add fixed voltage regulators to se7724
sh: add fixed voltage regulators to sdk7786
sh: add fixed voltage regulators to rsk
sh: add fixed voltage regulators to migor
sh: add fixed voltage regulators to kfr2r09
sh: add fixed voltage regulators to ap325rxa
sh: add fixed voltage regulators to sh7757lcr
sh: add fixed voltage regulators to sh2007
...
This contains a few patches that depend on
plugging changes in the block layer so needs to wait
for those.
It also contains a Kconfig fix for the new RAID10 support
in dm-raid.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ovN2
-----END PGP SIGNATURE-----
Merge tag 'md-3.6' of git://neil.brown.name/md
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
Now that DM_RAID supports raid10, it needs to select that code
to ensure it is included.
Cc: Jonathan Brassow <jbrassow@redhat.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
queuing writes to the md thread means that all requests go through the
one processor which may not be able to keep up with very high request
rates.
So use the plugging infrastructure to submit all requests on unplug.
If a 'schedule' is needed, we fall back on the old approach of handing
the requests to the thread for it to handle.
Signed-off-by: NeilBrown <neilb@suse.de>
Let raid5d handle stripe in batch way to reduce conf->device_lock locking.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
make_request() does stripe release for every stripe and the stripe usually has
count 1, which makes previous release_stripe() optimization not work. In my
test, this release_stripe() becomes the heaviest pleace to take
conf->device_lock after previous patches applied.
Below patch makes stripe release batch. All the stripes will be released in
unplug. The STRIPE_ON_UNPLUG_LIST bit is to protect concurrent access stripe
lru.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
It includes:
- large updates for OMAP
- support for LCD3 overlay manager (omap5)
- omapdss output cleanup
- removal of passive matrix LCD support as there are no drivers for
such panels for DSS or DSS2 and nobody complained (cleanup)
- large updates for SH Mobile
- overlay support
- separating MERAM (cache) from framebuffer driver
- some updates for Exynos and da8xx-fb
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=22b7
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.6' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- large updates for OMAP
- support for LCD3 overlay manager (omap5)
- omapdss output cleanup
- removal of passive matrix LCD support as there are no drivers for
such panels for DSS or DSS2 and nobody complained (cleanup)
- large updates for SH Mobile
- overlay support
- separating MERAM (cache) from framebuffer driver
- some updates for Exynos and da8xx-fb
- various other small patches
* tag 'fbdev-updates-for-3.6' of git://github.com/schandinat/linux-2.6: (78 commits)
da8xx-fb: fix compile issue due to missing include
fbdev: Make pixel_to_pat() failure mode more friendly
da8xx-fb: do not turn ON LCD backlight unless LCDC is enabled
fbdev: sh_mobile_lcdc: Fix vertical panning step
video: exynos mipi dsi: Fix mipi dsi regulators handling issue
video: da8xx-fb: do clock reset of revision 2 LCDC before enabling
arm: da850: configure LCDC fifo threshold
video: da8xx-fb: configure FIFO threshold to reduce underflow errors
video: da8xx-fb: fix flicker due to 1 frame delay in updated frame
video: da8xx-fb rev2: fix disabling of palette completion interrupt
da8xx-fb: add missing FB_BLANK operations
video: exynos_dp: use usleep_range instead of delay
video: exynos_dp: check the only INTERLANE_ALIGN_DONE bit during Link Training
fb: epson1355fb: Fix section mismatch
video: exynos_dp: fix wrong DPCD address during Link Training
video/smscufx: fix line counting in fb_write
aty128fb: Fix coding style issues
fbdev: sh_mobile_lcdc: Fix pan offset computation in YUV mode
fbdev: sh_mobile_lcdc: Fix overlay registers update during pan operation
fbdev: sh_mobile_lcdc: Support horizontal panning
...
Pull second vfs pile from Al Viro:
"The stuff in there: fsfreeze deadlock fixes by Jan (essentially, the
deadlock reproduced by xfstests 068), symlink and hardlink restriction
patches, plus assorted cleanups and fixes.
Note that another fsfreeze deadlock (emergency thaw one) is *not*
dealt with - the series by Fernando conflicts a lot with Jan's, breaks
userland ABI (FIFREEZE semantics gets changed) and trades the deadlock
for massive vfsmount leak; this is going to be handled next cycle.
There probably will be another pull request, but that stuff won't be
in it."
Fix up trivial conflicts due to unrelated changes next to each other in
drivers/{staging/gdm72xx/usb_boot.c, usb/gadget/storage_common.c}
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (54 commits)
delousing target_core_file a bit
Documentation: Correct s_umount state for freeze_fs/unfreeze_fs
fs: Remove old freezing mechanism
ext2: Implement freezing
btrfs: Convert to new freezing mechanism
nilfs2: Convert to new freezing mechanism
ntfs: Convert to new freezing mechanism
fuse: Convert to new freezing mechanism
gfs2: Convert to new freezing mechanism
ocfs2: Convert to new freezing mechanism
xfs: Convert to new freezing code
ext4: Convert to new freezing mechanism
fs: Protect write paths by sb_start_write - sb_end_write
fs: Skip atime update on frozen filesystem
fs: Add freezing handling to mnt_want_write() / mnt_drop_write()
fs: Improve filesystem freezing handling
switch the protection of percpu_counter list to spinlock
nfsd: Push mnt_want_write() outside of i_mutex
btrfs: Push mnt_want_write() outside of i_mutex
fat: Push mnt_want_write() outside of i_mutex
...
Pull block driver changes from Jens Axboe:
- Making the plugging support for drivers a bit more sane from Neil.
This supersedes the plugging change from Shaohua as well.
- The usual round of drbd updates.
- Using a tail add instead of a head add in the request completion for
ndb, making us find the most completed request more quickly.
- A few floppy changes, getting rid of a duplicated flag and also
running the floppy init async (since it takes forever in boot terms)
from Andi.
* 'for-3.6/drivers' of git://git.kernel.dk/linux-block:
floppy: remove duplicated flag FD_RAW_NEED_DISK
blk: pass from_schedule to non-request unplug functions.
block: stack unplug
blk: centralize non-request unplug handling.
md: remove plug_cnt feature of plugging.
block/nbd: micro-optimization in nbd request completion
drbd: announce FLUSH/FUA capability to upper layers
drbd: fix max_bio_size to be unsigned
drbd: flush drbd work queue before invalidate/invalidate remote
drbd: fix potential access after free
drbd: call local-io-error handler early
drbd: do not reset rs_pending_cnt too early
drbd: reset congestion information before reporting it in /proc/drbd
drbd: report congestion if we are waiting for some userland callback
drbd: differentiate between normal and forced detach
drbd: cleanup, remove two unused global flags
floppy: Run floppy initialization asynchronous
Pull core block IO bits from Jens Axboe:
"The most complicated part if this is the request allocation rework by
Tejun, which has been queued up for a long time and has been in
for-next ditto as well.
There are a few commits from yesterday and today, mostly trivial and
obvious fixes. So I'm pretty confident that it is sound. It's also
smaller than usual."
* 'for-3.6/core' of git://git.kernel.dk/linux-block:
block: remove dead func declaration
block: add partition resize function to blkpg ioctl
block: uninitialized ioc->nr_tasks triggers WARN_ON
block: do not artificially constrain max_sectors for stacking drivers
blkcg: implement per-blkg request allocation
block: prepare for multiple request_lists
block: add q->nr_rqs[] and move q->rq.elvpriv to q->nr_rqs_elvpriv
blkcg: inline bio_blkcg() and friends
block: allocate io_context upfront
block: refactor get_request[_wait]()
block: drop custom queue draining used by scsi_transport_{iscsi|fc}
mempool: add @gfp_mask to mempool_create_node()
blkcg: make root blkcg allocation use %GFP_KERNEL
blkcg: __blkg_lookup_create() doesn't need radix preload
Pull md updates from NeilBrown.
* 'for-next' of git://neil.brown.name/md:
DM RAID: Add support for MD RAID10
md/RAID1: Add missing case for attempting to repair known bad blocks.
md/raid5: For odirect-write performance, do not set STRIPE_PREREAD_ACTIVE.
md/raid1: don't abort a resync on the first badblock.
md: remove duplicated test on ->openers when calling do_md_stop()
raid5: Add R5_ReadNoMerge flag which prevent bio from merging at block layer
md/raid1: prevent merging too large request
md/raid1: read balance chooses idlest disk for SSD
md/raid1: make sequential read detection per disk based
MD RAID10: Export md_raid10_congested
MD: Move macros from raid1*.h to raid1*.c
MD RAID1: rename mirror_info structure
MD RAID10: rename mirror_info structure
MD RAID10: Fix compiler warning.
raid5: add a per-stripe lock
raid5: remove unnecessary bitmap write optimization
raid5: lockless access raid5 overrided bi_phys_segments
raid5: reduce chance release_stripe() taking device_lock
* set_fs(KERNEL_DS) + getname() is probably the weirdest implementation
of strdup() I've seen. Especially since they don't to copy it at all...
* filp_open() never returns NULL; it's ERR_PTR(-E...) on failure.
* file->f_dentry is never going to be NULL, TYVM.
* match_strdup() + snprintf() + kfree() is a bloody weird way to spell
match_strlcpy().
Pox on cargo-cult programmers...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Trivial support for irq domains, using either a linear map or radix tree
depending on the vector layout.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit ca5481c68e ("sh: pfc: Rudimentary
pinctrl-backed GPIO support.") introduced a regression for platforms that
were doing early GPIO API calls (from arch_initcall() or earlier),
leading to a situation where our two-stage registration logic would trip
itself up and we'd -ENODEV out of the pinctrl registration path,
resulting in endless -EPROBE_DEFER errors. Further lack of checking any
sort of errors from gpio_request() resulted in boot time warnings,
tripping on the FLAG_REQUESTED test-and-set in gpio_ensure_requested().
As it turns out there's no particular need to bother with the two-stage
registration, as the platform bus is already available at the point that
we have to start caring. As such, it's easiest to simply fold these
together in to a single init path, the ordering of which is ensured
through the platform's mux registration, as usual.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A recent commit:
commit d6fa5a4e7a
Author: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
serial: sh-sci: prepare for conversion to the shdma base library
is not sufficient to update the sh-sci driver to the new shdma driver
layout. This caused compilation breakage, when CONFIG_SERIAL_SH_SCI_DMA
is enabled. This patch trivially fixes the problem by updating the DMA
descriptor manipulation code.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The recent shdma driver split has mistakenly removed support for partial
DMA transfer size calculation on forced termination. This patch restores
it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Populate olpc_ec_priv with variables that were previously global. This
makes things a tad bit clearer, IMO.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Paul Fox <pgf@laptop.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
There's nothing about the debugfs interface for the EC driver that is
architecture-specific, so move it into the arch-independent driver.
The code is mostly unchanged with the exception of renamed variables, coding
style changes, and API updates.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Paul Fox <pgf@laptop.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
This uses the new EC driver framework in drivers/platform/olpc. The
XO-1 and XO-1.5-specific code is still in arch/x86, but the generic stuff
(including a new workqueue; no more running EC commands with IRQs disabled!)
can be shared with other architectures.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Paul Fox <pgf@laptop.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
A problem we've noticed on XO-1.75 is when we suspend in the middle of
an EC command. Don't allow that.
In the process, create a private object for the generic EC driver to use;
we have a framework for passing around a struct, use that rather than a
proliferation of global variables.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Paul Fox <pgf@laptop.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
The 1.75-based OLPC EC driver already does this; let's do it for all EC
drivers. This gives us nice suspend/resume hooks, amongst other things.
We want to run the EC's suspend hooks later than other drivers (which may
be setting wakeup masks or be running EC commands). We also want to run
the EC's resume hooks earlier than other drivers (which may want to run EC
commands).
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Paul Fox <pgf@laptop.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
This provides a new API allows different OLPC architectures to override the
EC driver. x86 and ARM OLPC machines use completely different EC backends.
The olpc_ec_cmd is synchronous, and waits for the workqueue to send the
command to the EC. Multiple callers can run olpc_ec_cmd() at once, and
they will by serialized and sleep while only one executes on the EC at a time.
We don't provide an unregister function, as that doesn't make sense within
the context of OLPC machines - there's only ever 1 EC, it's critical to
functionality, and it certainly not hotpluggable.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Paul Fox <pgf@laptop.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Switch over to using olpc-ec.h in multiple steps, so as not to break builds.
This covers every driver that calls olpc_ec_cmd().
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Paul Fox <pgf@laptop.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
The OLPC EC driver has outgrown arch/x86/platform/. It's time to both
share common code amongst different architectures, as well as move it out
of arch/x86/. The XO-1.75 is ARM-based, and the EC driver shares a lot of
code with the x86 code.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Paul Fox <pgf@laptop.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Merge Andrew's second set of patches:
- MM
- a few random fixes
- a couple of RTC leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (120 commits)
rtc/rtc-88pm80x: remove unneed devm_kfree
rtc/rtc-88pm80x: assign ret only when rtc_register_driver fails
mm: hugetlbfs: close race during teardown of hugetlbfs shared page tables
tmpfs: distribute interleave better across nodes
mm: remove redundant initialization
mm: warn if pg_data_t isn't initialized with zero
mips: zero out pg_data_t when it's allocated
memcg: gix memory accounting scalability in shrink_page_list
mm/sparse: remove index_init_lock
mm/sparse: more checks on mem_section number
mm/sparse: optimize sparse_index_alloc
memcg: add mem_cgroup_from_css() helper
memcg: further prevent OOM with too many dirty pages
memcg: prevent OOM with too many dirty pages
mm: mmu_notifier: fix freed page still mapped in secondary MMU
mm: memcg: only check anon swapin page charges for swap cache
mm: memcg: only check swap cache pages for repeated charging
mm: memcg: split swapin charge function into private and public part
mm: memcg: remove needless !mm fixup to init_mm when charging
mm: memcg: remove unneeded shmem charge type
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fx5A
-----END PGP SIGNATURE-----
Merge tag 'vfio-for-v3.6' of git://github.com/awilliam/linux-vfio
Pull VFIO core from Alex Williamson:
"This series includes the VFIO userspace driver interface for the 3.6
kernel merge window. This driver is intended to provide a secure
interface for device access using IOMMU protection for applications
like assignment of physical devices to virtual machines.
Qemu will be the first user of this interface, enabling assignment of
PCI devices to Qemu guests. This interface is intended to eventually
replace the x86-specific assignment mechanism currently available in
KVM.
This interface has the advantage of being more secure, by working with
IOMMU groups to ensure device isolation and providing it's own
filtered resource access mechanism, and also more flexible, in not
being x86 or KVM specific (extensions to enable POWER are already
working).
This driver is originally the work of Tom Lyon, but has since been
handed over to me and gone through a complete overhaul thanks to the
input from David Gibson, Ben Herrenschmidt, Chris Wright, Joerg
Roedel, and others. This driver has been available in linux-next for
the last month."
Paul Mackerras says:
"I would be glad to see it go in since we want to use it with KVM on
PowerPC. If possible we'd like the PowerPC bits for it to go in as
well."
* tag 'vfio-for-v3.6' of git://github.com/awilliam/linux-vfio:
vfio: Add PCI device driver
vfio: Type1 IOMMU implementation
vfio: Add documentation
vfio: VFIO core
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
- Fix IPoIB to stop using unsafe linkage between networking neighbour
layer and private path database.
- Small fixes for bugs found by Fengguang Wu's automated builds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zFTH
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull final RDMA changes from Roland Dreier:
- Fix IPoIB to stop using unsafe linkage between networking neighbour
layer and private path database.
- Small fixes for bugs found by Fengguang Wu's automated builds.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Use a private hash table for path lookup in xmit path
IB/qib: Fix size of cc_supported_table_entries
RDMA/ucma: Convert open-coded equivalent to memdup_user()
RDMA/ocrdma: Fix check of GSI CQs
RDMA/cma: Use PTR_RET rather than if (IS_ERR(...)) + PTR_ERR
Guenter Roeck