IPv6 IPsec tunnel gateway incorrectly sends redirect to
router or sender when network device the IPsec tunnelled packet
is arrived is the same as the one the decapsulated packet
is sent.
With this patch, it omits to send the redirect when the forwarding
skbuff carries secpath, since such skbuff should be assumed as
a decapsulated packet from IPsec tunnel by own.
It may be a rare case for an IPsec security gateway, however
it is not rare when the gateway is MIPv6 Home Agent since
the another tunnel end-point is Mobile Node and it changes
the attached network.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When XFRM policy and state are ready after TCP connection is started,
the traffic should be transformed immediately, however it does not
on IPv6 TCP.
It depends on a dst cache replacement policy with connected socket.
It seems that the replacement is always done for IPv4, however, on
IPv6 case it is done only when routing cookie is changed.
This patch fix that non-transformation dst can be changed to
transformation one.
This behavior is required by MIPv6 and improves IPv6 IPsec.
Fixes by Masahide NAKAMURA.
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add v4mapped address inline to avoid calls to ipv6_addr_type().
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ICMPv6 Target address is multicast, Linux processes the
redirect instead of dropping it. The problem is in this code in
ndisc_redirect_rcv():
if (ipv6_addr_equal(dest, target)) {
on_link = 1;
} else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) {
ND_PRINTK2(KERN_WARNING
"ICMPv6 Redirect: target address is not
link-local.\n");
return;
}
This second check will succeed if the Target address is, for example,
FF02::1 because it has link-local scope. Instead, it should be checking
if it's a unicast link-local address, as stated in RFC 2461/4861 Section
8.1:
- The ICMP Target Address is either a link-local address (when
redirected to a router) or the same as the ICMP Destination
Address (when redirected to the on-link destination).
I know this doesn't explicitly say unicast link-local address, but it's
implied.
This bug is preventing Linux kernels from achieving IPv6 Logo Phase II
certification because of a recent error that was found in the TAHI test
suite - Neighbor Disovery suite test 206 (v6LC.2.3.6_G) had the
multicast address in the Destination field instead of Target field, so
we were passing the test. This won't be the case anymore.
The patch below fixes this problem, and also fixes ndisc_send_redirect()
to not send an invalid redirect with a multicast address in the Target
field. I re-ran the TAHI Neighbor Discovery section to make sure Linux
passes all 245 tests now.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a report and initial patch by Peter Lieven.
tcp4_md5sig_key and tcp6_md5sig_key need to start with
the exact same members as tcp_md5sig_key. Because they
are both cast to that type by tcp_v{4,6}_md5_do_lookup().
Unfortunately tcp{4,6}_md5sig_key use a u16 for the key
length instead of a u8, which is what tcp_md5sig_key
uses. This just so happens to work by accident on
little-endian, but on big-endian it doesn't.
Instead of casting, just place tcp_md5sig_key as the first member of
the address-family specific structures, adjust the access sites, and
kill off the ugly casts.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 95c385 broke proper source address selection for cases in which
there is a address which is makred 'deprecated'. The commit mistakenly
changed ifa->flags to ifa_result->flags (probably copy/paste error from a
few lines above) in the 'Rule 3' address selection code.
The patch restores the previous RFC-compliant behavior.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of skbs in sk->write_queue do not have skb->dst because
we do not fill skb->dst when we allocate new skb in append_data().
BTW, I think we may not need to (or we should not) increment some stats
when using corking; if 100 sendmsg() (with MSG_MORE) result in 2 packets,
how many should we increment?
If 100, we should set skb->dst for every queued skbs.
If 1 (or 2 (*)), we increment the stats for the first queued skb and
we should just skip incrementing OutDiscards for the rest of queued skbs,
adn we should also impelement this semantics in other places;
e.g., we should increment other stats just once, not 100 times.
*: depends on the place we are discarding the datagram.
I guess should just increment by 1 (or 2).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
So I've had a deadlock reported to me. I've found that the sequence of
events goes like this:
1) process A (modprobe) runs to remove ip_tables.ko
2) process B (iptables-restore) runs and calls setsockopt on a netfilter socket,
increasing the ip_tables socket_ops use count
3) process A acquires a file lock on the file ip_tables.ko, calls remove_module
in the kernel, which in turn executes the ip_tables module cleanup routine,
which calls nf_unregister_sockopt
4) nf_unregister_sockopt, seeing that the use count is non-zero, puts the
calling process into uninterruptible sleep, expecting the process using the
socket option code to wake it up when it exits the kernel
4) the user of the socket option code (process B) in do_ipt_get_ctl, calls
ipt_find_table_lock, which in this case calls request_module to load
ip_tables_nat.ko
5) request_module forks a copy of modprobe (process C) to load the module and
blocks until modprobe exits.
6) Process C. forked by request_module process the dependencies of
ip_tables_nat.ko, of which ip_tables.ko is one.
7) Process C attempts to lock the request module and all its dependencies, it
blocks when it attempts to lock ip_tables.ko (which was previously locked in
step 3)
Theres not really any great permanent solution to this that I can see, but I've
developed a two part solution that corrects the problem
Part 1) Modifies the nf_sockopt registration code so that, instead of using a
use counter internal to the nf_sockopt_ops structure, we instead use a pointer
to the registering modules owner to do module reference counting when nf_sockopt
calls a modules set/get routine. This prevents the deadlock by preventing set 4
from happening.
Part 2) Enhances the modprobe utilty so that by default it preforms non-blocking
remove operations (the same way rmmod does), and add an option to explicity
request blocking operation. So if you select blocking operation in modprobe you
can still cause the above deadlock, but only if you explicity try (and since
root can do any old stupid thing it would like.... :) ).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Denis V. Lunev <den@openvz.org>
addrconf_dad_failure calls addrconf_dad_stop which takes referenced address
and drops the count. So, in6_ifa_put perrformed at out: is extra. This
results in message: "Freeing alive inet6 address" and not released dst entries.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix IP[V6]_ADD_MEMBERSHIP and IP[V6]_DROP_MEMBERSHIP to
return -EPROTO for connection oriented sockets.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix to netfilter from Eric Dumazet inspired me to
look around a bit by using some grep/sed stuff as looking for
this kind of bugs seemed easy to automate. This is one of them
I found where it looks like this semicolon is not valid.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up duplicate includes in
net/ipv6/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discovered by Evegniy Polyakov, if we try to sendmsg after
a connection reset, we can do incredibly stupid things.
The core issue is that inet_sendmsg() tries to autobind the
socket, but we should never do that for TCP. Instead we should
just go straight into TCP's sendmsg() code which will do all
of the necessary state and pending socket error checks.
TCP's sendpage already directly vectors to tcp_sendpage(), so this
merely brings sendmsg() in line with that.
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_addr_type() doesn't check for 'Unique Local IPv6 Unicast
Addresses' (RFC4193) and returns IPV6_ADDR_RESERVED for that range.
SCTP uses this function and will fail bind() and connect() calls that
use RFC4193 addresses, SCTP will also ignore inbound connections from
RFC4193 addresses if listening on IPV6_ADDR_ANY.
There may be other users of ipv6_addr_type() that could also have
problems.
Signed-off-by: Dave Johnson <djohnson@sw.starentnetworks.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that netdev notifications can fail, we can use this to signal
errors during registration for IPv4/IPv6. In particular, if we
fail to allocate memory for the inet device, we can fail the netdev
registration.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADVMSS value was incorrectly updated for ALL routes when the MTU
is updated because it's outside the effect of the if statement's
condition.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert rel_info to host-endian before calling ip6_tnl_err().
The things become much more straightforward that way.
The key observation (and the reason why that code actually
worked) is that after ip6_tnl_err() we either immediately
bailed out or had rel_info set to 0 or had it set to host-endian
and guaranteed to hit
(rel_type == ICMP_DEST_UNREACH && rel_code == ICMP_FRAG_NEEDED)
case. So inconsistent endianness didn't really lead to bugs,
but it had been subtle and prone to breakage. New variant is
saner and obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Loading one of the LOG target fails if a different target has already
registered itself as backend for the same family. This can affect the
ipt_LOG and ipt_ULOG modules when both are loaded.
Reported and tested by: <t.artem@mailcity.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After clearing all passwords for IPv6 peers, we need to
set allocation count to zero as well as we free the storage.
Otherwise, we panic when a user trys to (re)add a password.
Discovered and fixed by MIYAJIMA Mitsuharu <miyajima.mitsuharu@anchor.jp>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently if the link is brought down via ip link or ifconfig down,
the inet6addr_chain notifiers are not called even though all
the addresses are removed from the interface. This caused SCTP
to add duplicate addresses to it's list.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Dmitry Butskoy <dmitry@butskoy.name>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=8747
Problem Description:
It is related to the possibility to obtain MSG_ERRQUEUE messages from the udp
and raw sockets, both connected and unconnected.
There is a little typo in net/ipv6/icmp.c code, which prevents such messages
to be delivered to the errqueue of the correspond raw socket, when the socket
is CONNECTED. The typo is due to swap of local/remote addresses.
Consider __raw_v6_lookup() function from net/ipv6/raw.c. When a raw socket is
looked up usual way, it is something like:
sk = __raw_v6_lookup(sk, nexthdr, daddr, saddr, IP6CB(skb)->iif);
where "daddr" is a destination address of the incoming packet (IOW our local
address), "saddr" is a source address of the incoming packet (the remote end).
But when the raw socket is looked up for some icmp error report, in
net/ipv6/icmp.c:icmpv6_notify() , daddr/saddr are obtained from the echoed
fragment of the "bad" packet, i.e. "daddr" is the original destination
address of that packet, "saddr" is our local address. Hence, for
icmpv6_notify() must use "saddr, daddr" in its arguments, not "daddr, saddr"
...
Steps to reproduce:
Create some raw socket, connect it to an address, and cause some error
situation: f.e. set ttl=1 where the remote address is more than 1 hop to reach.
Set IPV6_RECVERR .
Then send something and wait for the error (f.e. poll() with POLLERR|POLLIN).
You should receive "time exceeded" icmp message (because of "ttl=1"), but the
socket do not receive it.
If you do not connect your raw socket, you will receive MSG_ERRQUEUE
successfully. (The reason is that for unconnected socket there are no actual
checks for local/remote addresses).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove two unnecessary EXPORT_SYMBOLs and move the
nf_conntrack_l3proto_ipv4 declaration to the correct file.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lower ip6tables, arptables and ebtables printk severity similar to
Dan Aloni's patch for iptables.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_ct_get_tuple() requires the offset to transport header and that bothers
callers such as icmp[v6] l4proto modules. This introduces new function
to simplify them.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The icmp[v6] l4proto modules parse headers in ICMP[v6] error to get tuple.
But they have to find the offset to transport protocol header before that.
Their processings are almost same as prepare() of l3proto modules.
This makes prepare() more generic to simplify icmp[v6] l4proto module
later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all initialized struct seq_operations in net/ const
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial patch removes the unneeded pointer idev returned from
__in6_dev_get(), which is never used. The check for NULL can be simply
done by if (__in6_dev_get(dev) == NULL).
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because reversing RH0 is no longer supported by deprecation
of RH0, let's make IPV6_{RECV,2292}RTHDR boolean options.
Boolean are more appropriate from standard POV.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on <draft-ietf-ipv6-deprecate-rh0-00.txt>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "fix" for emerging security threat was overkill and it broke
basic semantic of IPv6 routing header processing. We should assume
RT0 (or even RT2, depends on configuration) as "unknown" RH type so
that we
- silently ignore the routing header if segleft == 0
- send ICMPv6 Parameter Problem message back to the sender,
otherwise.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert DEBUGP to pr_debug and fix lots of non-compiling debug statements.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers pass NULL, this also doesn't seem very useful for modules.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now memory space for help and NAT are allocated by extension
infrastructure.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TRACE target can be used to follow IP and IPv6 packets through
the ruleset.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick NcHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes redundant parentheses and braces (And add one pair in a
xt_tcpudp.c macro).
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make a number of variables const and/or remove unneeded casts.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the return type of target checkentry functions to boolean.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the return type of match functions to boolean
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the return type of match functions to boolean
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the "hotdrop" variables to boolean
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing model for checksum offload does not correctly handle
devices that can offload IPV4 and IPV6 only. The NETIF_F_HW_CSUM flag
implies device can do any arbitrary protocol.
This patch:
* adds NETIF_F_IPV6_CSUM for those devices
* fixes bnx2 and tg3 devices that need it
* add NETIF_F_IPV6_CSUM to ipv6 output (incl GSO)
* fixes assumptions about NETIF_F_ALL_CSUM in nat
* adjusts bridge union of checksumming computation
Signed-off-by: David S. Miller <davem@davemloft.net>
Masahide NAKAMURA