This patch adds common driver for the Top block of the Samsung Exynos
SoC Low Power Audio Subsystem. This is a minimal driver which prepares
resources for IP blocks like I2S, audio DMA and UART and exposes
a regmap for the Top block registers. Also system power ops are added
to ensure the Audio Subsystem is operational after system suspend/resume
cycle.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
set_bit() and clear_bit() take the bit number so this code is really
doing "1 << (1 << irq)" which is a double shift bug. It's done
consistently so it won't cause a problem unless "irq" is more than 4.
Fixes: 70c6cce040 ('mfd: Support 88pm80x in 80x driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove incorrect e-mail addresses from the copyright header and
MODULE_AUTHOR() macro. These e-mail addresses are no longer in use.
The author names have not been changed, only the e-mail addresses have
been deleted from the source files.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds requesting of the clocks supplied on MCLK1, MCLK2 pins,
gating of the 32k clock is added to the arizona_clk32k_enable(),
arizona_clk32k_disable() helpers.
It's a temporary change until the CODEC's clock controller gets exposed
through the clk API and is helpful for board configurations where the
MCLK clocks are not provided by always on oscillators.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
SoC, along with a master AXP809 PMIC.
This PMIC has a new register layout, and supports some functions not
seen in other X-Powers PMICs, such as master-slave mode, or having
multiple AXP806 PMICs on the same bus with address space extension,
or supporting both I2C and RSB mode. I2C has not been tested.
This patch adds support for the interrupts of the PMIC. A regulator
sub-device is enabled, but actual regulator support will come in a
later patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK818 chip is a Power Management IC (PMIC) for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clocking
- Battery support
Both RK808 and RK818 chips are using a similar register map,
so we can reuse the RTC and Clocking functionality.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The LP873X chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Regulators.
- Configurable General Purpose Output Signals (GPO).
PMIC interacts with the main processor through i2c. PMIC has
couple of LDOs (Linear Regulators), couple of BUCKs (Step-Down DC-DC
Converter Cores) and GPOs (General Purpose Output Signals).
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Newer revisions of the ChromeOS EC add more events besides the keyboard
ones. So handle interrupts in the MFD driver and let consumers register
for notifications for the events they might care.
To keep backward compatibility, if the EC doesn't support MKBP event, we
fall back to the old MKBP key matrix host command.
Cc: Randall Spangler <rspangler@chromium.org>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Vic Yang <victoryang@google.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In order to support the Qualcomm MDM9615 SoC, add support for the
RPM regulator entries in the qcom-rpm driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
PPC splits debugfs initialization from creation of the xics device to
unlock the newly taken kvm lock earlier.
s390 prevents userspace from triggering two WARN_ON_ONCE.
MIPS fixes several issues in the management of TLB faults (Cc: stable).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXrx2ZAAoJEED/6hsPKofoo/4H/jra5NNxvpo09LWlXTwGXxBH
cwcfDZSiOFxgvWztKJOIjPI4ETL3mnZvb9SFWBZZh1U0kfZ/TGiWouwaDNlBkPYj
I3YHuPI7if+yUOmJlI3N2hWa0Wo0qiMqIjKT0pQVSLLdK/CVE+xGyS+qtXTNXHQn
pFdKlYr//7OwQEY0ow1yj5VnsFrXB1JWFyB/+N5zaCfbCaQVyZAL7rj8SUbC/32W
CiNhrvatzierKIfPerWw8DvvBKhCgWaRuLl0W+uMncrC9Qepcx9moM2beD1txK2I
iHor1TDxUPifGQONfWMAlw87FluzHF4vQ5nN2jyTi8TT+CEfZpZ43Q+DY7okD4w=
=NQP9
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"KVM:
- lock kvm_device list to prevent corruption on device creation.
PPC:
- split debugfs initialization from creation of the xics device to
unlock the newly taken kvm lock earlier.
s390:
- prevent userspace from triggering two WARN_ON_ONCE.
MIPS:
- fix several issues in the management of TLB faults (Cc: stable)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
MIPS: KVM: Propagate kseg0/mapped tlb fault errors
MIPS: KVM: Fix gfn range check in kseg0 tlb faults
MIPS: KVM: Add missing gfn range check
MIPS: KVM: Fix mapped fault broken commpage handling
KVM: Protect device ops->create and list_add with kvm->lock
KVM: PPC: Move xics_debugfs_init out of create
KVM: s390: reset KVM_REQ_MMU_RELOAD if mapping the prefix failed
KVM: s390: set the prefix initially properly
Pull block fixes from Jens Axboe:
- an NVMe fix from Gabriel, fixing a suspend/resume issue on some
setups
- addition of a few missing entries in the block queue sysfs
documentation, from Joe
- a fix for a sparse shadow warning for the bvec iterator, from
Johannes
- a writeback deadlock involving raid issuing barriers, and not
flushing the plug when we wakeup the flusher threads. From
Konstantin
- a set of patches for the NVMe target/loop/rdma code, from Roland and
Sagi
* 'for-linus' of git://git.kernel.dk/linux-block:
bvec: avoid variable shadowing warning
doc: update block/queue-sysfs.txt entries
nvme: Suspend all queues before deletion
mm, writeback: flush plugged IO in wakeup_flusher_threads()
nvme-rdma: Remove unused includes
nvme-rdma: start async event handler after reconnecting to a controller
nvmet: Fix controller serial number inconsistency
nvmet-rdma: Don't use the inline buffer in order to avoid allocation for small reads
nvmet-rdma: Correctly handle RDMA device hot removal
nvme-rdma: Make sure to shutdown the controller if we can
nvme-loop: Remove duplicate call to nvme_remove_namespaces
nvme-rdma: Free the I/O tags when we delete the controller
nvme-rdma: Remove duplicate call to nvme_remove_namespaces
nvme-rdma: Fix device removal handling
nvme-rdma: Queue ns scanning after a sucessful reconnection
nvme-rdma: Don't leak uninitialized memory in connect request private data
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus two uncore-PMU fixes, an uprobes fix, a
perf-cgroups fix and an AUX events fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Add enable_box for client MSR uncore
perf/x86/intel/uncore: Fix uncore num_counters
uprobes/x86: Fix RIP-relative handling of EVEX-encoded instructions
perf/core: Set cgroup in CPU contexts for new cgroup events
perf/core: Fix sideband list-iteration vs. event ordering NULL pointer deference crash
perf probe ppc64le: Fix probe location when using DWARF
perf probe: Add function to post process kernel trace events
tools: Sync cpufeatures headers with the kernel
toops: Sync tools/include/uapi/linux/bpf.h with the kernel
tools: Sync cpufeatures.h and vmx.h with the kernel
perf probe: Support signedness casting
perf stat: Avoid skew when reading events
perf probe: Fix module name matching
perf probe: Adjust map->reloc offset when finding kernel symbol from map
perf hists: Trim libtraceevent trace_seq buffers
perf script: Add 'bpf-output' field to usage message
Pull locking fixes from Ingo Molnar:
"Misc fixes: lockstat fix, futex fix on !MMU systems, big endian fix
for qrwlocks and a race fix for pvqspinlocks"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/pvqspinlock: Fix a bug in qstat_read()
locking/pvqspinlock: Fix double hash race
locking/qrwlock: Fix write unlock bug on big endian systems
futex: Assume all mappings are private on !MMU systems
Pull irq fix from Ingo Molnar:
"A fix for an MSI regression"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi: Make sure PCI MSIs are activated early
Highlights include:
- Stable patch from Olga to fix RPCSEC_GSS upcalls when the same user needs
multiple different security services (e.g. krb5i and krb5p).
- Stable patch to fix a regression introduced by the use of SO_REUSEPORT,
and that prevented the use of multiple different NFS versions to the
same server.
- TCP socket reconnection timer fixes.
- Patch from Neil to disable the use of IPv6 temporary addresses.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UHph
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.8-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Stable patch from Olga to fix RPCSEC_GSS upcalls when the same user
needs multiple different security services (e.g. krb5i and krb5p).
- Stable patch to fix a regression introduced by the use of
SO_REUSEPORT, and that prevented the use of multiple different NFS
versions to the same server.
- TCP socket reconnection timer fixes.
- Patch from Neil to disable the use of IPv6 temporary addresses"
* tag 'nfs-for-4.8-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Cap the transport reconnection timer at 1/2 lease period
NFSv4: Cleanup the setting of the nfs4 lease period
SUNRPC: Limit the reconnect backoff timer to the max RPC message timeout
SUNRPC: Fix reconnection timeouts
NFSv4.2: LAYOUTSTATS may return NFS4ERR_ADMIN/DELEG_REVOKED
SUNRPC: disable the use of IPv6 temporary addresses.
SUNRPC: allow for upcalls for same uid but different gss service
SUNRPC: Fix up socket autodisconnect
SUNRPC: Handle EADDRNOTAVAIL on connection failures
- powerpc/vdso: Fix build rules to rebuild vdsos correctly from Nicholas Piggin
- powerpc/ptrace: Fix coredump since ptrace TM changes from Cyril Bur
- powerpc/32: Fix csum_partial_copy_generic() from Christophe Leroy
- cxl: Set psl_fir_cntl to production environment value from Frederic Barrat
- powerpc/eeh: Switch to conventional PCI address output in EEH log from Guilherme G. Piccoli
- cxl: Use fixed width predefined types in data structure. from Philippe Bergheaud
- powerpc/vdso: Add missing include file from Guenter Roeck
- powerpc: Fix unused function warning 'lmb_to_memblock' from Alastair D'Silva
- powerpc/powernv/ioda: Fix TCE invalidate to work in real mode again from Alexey Kardashevskiy
- powerpc/cell: Add missing error code in spufs_mkgang() from Dan Carpenter
- crypto: crc32c-vpmsum - Convert to CPU feature based module autoloading from Anton Blanchard
- powerpc/pasemi: Fix coherent_dma_mask for dma engine from Darren Stevens
Benjamin Herrenschmidt:
- powerpc/32: Fix crash during static key init
- powerpc: Update obsolete comment in setup_32.c about early_init()
- powerpc: Print the kernel load address at the end of prom_init()
- powerpc/pnv/pci: Fix incorrect PE reservation attempt on some 64-bit BARs
- powerpc/xics: Properly set Edge/Level type and enable resend
Mahesh Salgaonkar:
- powerpc/book3s: Fix MCE console messages for unrecoverable MCE.
- powerpc/powernv: Fix MCE handler to avoid trashing CR0/CR1 registers.
- powerpc/powernv: Move IDLE_STATE_ENTER_SEQ macro to cpuidle.h
- powerpc/powernv: Load correct TOC pointer while waking up from winkle.
Andrew Donnellan:
- cxl: Fix sparse warnings
- cxl: Fix NULL dereference in cxl_context_init() on PowerVM guests
Michael Ellerman:
- selftests/powerpc: Specify we expect to build with std=gnu99
- powerpc/Makefile: Use cflags-y/aflags-y for setting endian options
- powerpc/pci: Fix endian bug in fixed PHB numbering
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gw2z
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some powerpc fixes for 4.8:
Misc:
- powerpc/vdso: Fix build rules to rebuild vdsos correctly from Nicholas Piggin
- powerpc/ptrace: Fix coredump since ptrace TM changes from Cyril Bur
- powerpc/32: Fix csum_partial_copy_generic() from Christophe Leroy
- cxl: Set psl_fir_cntl to production environment value from Frederic Barrat
- powerpc/eeh: Switch to conventional PCI address output in EEH log from Guilherme G. Piccoli
- cxl: Use fixed width predefined types in data structure. from Philippe Bergheaud
- powerpc/vdso: Add missing include file from Guenter Roeck
- powerpc: Fix unused function warning 'lmb_to_memblock' from Alastair D'Silva
- powerpc/powernv/ioda: Fix TCE invalidate to work in real mode again from Alexey Kardashevskiy
- powerpc/cell: Add missing error code in spufs_mkgang() from Dan Carpenter
- crypto: crc32c-vpmsum - Convert to CPU feature based module autoloading from Anton Blanchard
- powerpc/pasemi: Fix coherent_dma_mask for dma engine from Darren Stevens
Benjamin Herrenschmidt:
- powerpc/32: Fix crash during static key init
- powerpc: Update obsolete comment in setup_32.c about early_init()
- powerpc: Print the kernel load address at the end of prom_init()
- powerpc/pnv/pci: Fix incorrect PE reservation attempt on some 64-bit BARs
- powerpc/xics: Properly set Edge/Level type and enable resend
Mahesh Salgaonkar:
- powerpc/book3s: Fix MCE console messages for unrecoverable MCE.
- powerpc/powernv: Fix MCE handler to avoid trashing CR0/CR1 registers.
- powerpc/powernv: Move IDLE_STATE_ENTER_SEQ macro to cpuidle.h
- powerpc/powernv: Load correct TOC pointer while waking up from winkle.
Andrew Donnellan:
- cxl: Fix sparse warnings
- cxl: Fix NULL dereference in cxl_context_init() on PowerVM guests
Michael Ellerman:
- selftests/powerpc: Specify we expect to build with std=gnu99
- powerpc/Makefile: Use cflags-y/aflags-y for setting endian options
- powerpc/pci: Fix endian bug in fixed PHB numbering"
* tag 'powerpc-4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (26 commits)
selftests/powerpc: Specify we expect to build with std=gnu99
powerpc/vdso: Fix build rules to rebuild vdsos correctly
powerpc/Makefile: Use cflags-y/aflags-y for setting endian options
powerpc/32: Fix crash during static key init
powerpc: Update obsolete comment in setup_32.c about early_init()
powerpc: Print the kernel load address at the end of prom_init()
powerpc/ptrace: Fix coredump since ptrace TM changes
powerpc/32: Fix csum_partial_copy_generic()
cxl: Set psl_fir_cntl to production environment value
powerpc/pnv/pci: Fix incorrect PE reservation attempt on some 64-bit BARs
powerpc/book3s: Fix MCE console messages for unrecoverable MCE.
powerpc/pci: Fix endian bug in fixed PHB numbering
powerpc/eeh: Switch to conventional PCI address output in EEH log
cxl: Fix sparse warnings
cxl: Fix NULL dereference in cxl_context_init() on PowerVM guests
cxl: Use fixed width predefined types in data structure.
powerpc/vdso: Add missing include file
powerpc: Fix unused function warning 'lmb_to_memblock'
powerpc/powernv: Fix MCE handler to avoid trashing CR0/CR1 registers.
powerpc/powernv: Move IDLE_STATE_ENTER_SEQ macro to cpuidle.h
...
KVM devices were manipulating list data structures without any form of
synchronization, and some implementations of the create operations also
suffered from a lack of synchronization.
Now when we've split the xics create operation into create and init, we
can hold the kvm->lock mutex while calling the create operation and when
manipulating the devices list.
The error path in the generic code gets slightly ugly because we have to
take the mutex again and delete the device from the list, but holding
the mutex during anon_inode_getfd or releasing/locking the mutex in the
common non-error path seemed wrong.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
As we are about to hold the kvm->lock during the create operation on KVM
devices, we should move the call to xics_debugfs_init into its own
function, since holding a mutex over extended amounts of time might not
be a good idea.
Introduce an init operation on the kvm_device_ops struct which cannot
fail and call this, if configured, after the device has been created.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
- Misc fixes and cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXq0ruAAoJECgfDbjSjVRp5P8H/2OlDJdSS1l+TwOXbY95ntQ1
vxUX4vGCX5IujC+Rbt7sQV2prE3b6IktFNagpbRoWn21JkpoDMvPtYJrn5BhLtoh
fvDkZE6Wo3QztFSjaUBZWEABBt03KPX0yrAIZplu8ne/Z8KAT3zK57BPnKfmxwv+
dpxt+1wlnqAvYsoUUQZBFT4Gmk2oDiTofiIbQq7W9W/fooznLtLB+ArYtdfNJizC
JnI/vJuWceEXfjT26HexCRhA2OZskrA4ZadDhOjAqkTPN5DHfweLDuHh7IsVfDd1
wXqjc4ks3cYG0CloJ2qY2K7RpDOFIxIizixeDIuAbn9aX4sPOYYfqRm+4iRwmqQ=
=9aUO
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost fixes and cleanups from Michael Tsirkin:
"Misc fixes and cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: deprecate old transport
virtio/s390: keep early_put_chars
virtio_blk: Fix a slient kernel panic
virtio-vsock: fix include guard typo
vhost/vsock: fix vhost virtio_vsock_pkt use-after-free
9p/trans_virtio: use kvfree() for iov_iter_get_pages_alloc()
virtio: fix error handling for debug builds
virtio: fix memory leak in virtqueue_add()
Due to the (indirect) nesting of min(..., min(...)), sparse will
show a variable shadowing warning whenever bvec.h is included.
Avoid that by assigning the inner min() to a temporary variable first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch aims to get rid of endianness in queued_write_unlock(). We
want to set __qrwlock->wmode to NULL, however the address is not
&lock->cnts in big endian machine. That causes queued_write_unlock()
write NULL to the wrong field of __qrwlock.
So implement __qrwlock_write_byte() which returns the correct
__qrwlock->wmode address.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman.Long@hpe.com
Cc: arnd@arndb.de
Cc: boqun.feng@gmail.com
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1468835259-4486-1-git-send-email-xinhui.pan@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There's a perf stat bug easy to observer on a machine with only one cgroup:
$ perf stat -e cycles -I 1000 -C 0 -G /
# time counts unit events
1.000161699 <not counted> cycles /
2.000355591 <not counted> cycles /
3.000565154 <not counted> cycles /
4.000951350 <not counted> cycles /
We'd expect some output there.
The underlying problem is that there is an optimization in
perf_cgroup_sched_{in,out}() that skips the switch of cgroup events
if the old and new cgroups in a task switch are the same.
This optimization interacts with the current code in two ways
that cause a CPU context's cgroup (cpuctx->cgrp) to be NULL even if a
cgroup event matches the current task. These are:
1. On creation of the first cgroup event in a CPU: In current code,
cpuctx->cpu is only set in perf_cgroup_sched_in, but due to the
aforesaid optimization, perf_cgroup_sched_in will run until the next
cgroup switches in that CPU. This may happen late or never happen,
depending on system's number of cgroups, CPU load, etc.
2. On deletion of the last cgroup event in a cpuctx: In list_del_event,
cpuctx->cgrp is set NULL. Any new cgroup event will not be sched in
because cpuctx->cgrp == NULL until a cgroup switch occurs and
perf_cgroup_sched_in is executed (updating cpuctx->cgrp).
This patch fixes both problems by setting cpuctx->cgrp in list_add_event,
mirroring what list_del_event does when removing a cgroup event from CPU
context, as introduced in:
commit 68cacd2916 ("perf_events: Fix stale ->cgrp pointer in update_cgrp_time_from_cpuctx()")
With this patch, cpuctx->cgrp is always set/clear when installing/removing
the first/last cgroup event in/from the CPU context. With cpuctx->cgrp
correctly set, event_filter_match works as intended when events are
sched in/out.
After the fix, the output is as expected:
$ perf stat -e cycles -I 1000 -a -G /
# time counts unit events
1.004699159 627342882 cycles /
2.007397156 615272690 cycles /
3.010019057 616726074 cycles /
Signed-off-by: David Carrillo-Cisneros <davidcc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1470124092-113192-1-git-send-email-davidcc@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
STMPE1600 is a 16-bit port expander.
Datasheet is available here :
http://www2.st.com/content/st_com/en/products/interfaces-and-transceivers/
i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html
Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
this update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset
This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.
For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As STMPE1801/1601/24xx has a SYS_CTRL register and
STMPE1601/2403 has even a SYS_CTRL2 register, add
STMPE_IDX_SYS_CTRL/2 and update driver code accordingly
This update prepares the ground for not yet supported STMPE1600
which share similar REG_SYS_CTRL register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This reverts commit 874f9c7da9.
Geert Uytterhoeven reports:
"This change seems to have an (unintendent?) side-effect.
Before, pr_*() calls without a trailing newline characters would be
printed with a newline character appended, both on the console and in
the output of the dmesg command.
After this commit, no new line character is appended, and the output
of the next pr_*() call of the same type may be appended, like in:
- Truncating RAM at 0x0000000040000000-0x00000000c0000000 to -0x0000000070000000
- Ignoring RAM at 0x0000000200000000-0x0000000240000000 (!CONFIG_HIGHMEM)
+ Truncating RAM at 0x0000000040000000-0x00000000c0000000 to -0x0000000070000000Ignoring RAM at 0x0000000200000000-0x0000000240000000 (!CONFIG_HIGHMEM)"
Joe Perches says:
"No, that is not intentional.
The newline handling code inside vprintk_emit is a bit involved and
for now I suggest a revert until this has all the same behavior as
earlier"
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Requested-by: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
properly by the tracing user space tools. This was due to the
TRACE_DEFINE_ENUM() being set to a define, when it should have been set
to the enum itself. The define was of the MASK that used the BIT to shift.
The BIT was the enum and by adding that, everything gets converted nicely.
The MASK is still kept just in case it gets converted to an enum in the
future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXqeA/AAoJEKKk/i67LK/8wLAH/0nD8L5pxtn+pZi3mQnWNwbn
qEBtfKK8cvnt0IWH2HlKmRKLAiIJfp8UrkGoPiLT7Nb83PlKaw3UT868t7eDmknu
b29SsZroMgvJ1MeeNH9Yzk7cK3/K213VO02P4ce8EWSELYCqFlxJDE3dhl52K9Lj
clJSoZbIGTLlx4pk6zZnPksTt3Z9WZXcVJITwxEiz/Cr+CKAWZpLoPPUaqJOmA4j
9oS6d++0DYZdz3cWCmYBBkphmc5IQkBNZWGMYLcAR+M+m5fsN+baWlP3Dhq4j7he
WknHwu4WDFMk6a2Kh0Ggi6yUWVUIkLNY2Z4QUF2gNmJT1g/FH5lZka4/kIxjvKw=
=rgBA
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix tick_stop tracepoint symbols for user export.
Luiz Capitulino noticed that the tick_stop tracepoint wasn't being
parsed properly by the tracing user space tools.
This was due to the TRACE_DEFINE_ENUM() being set to a define, when it
should have been set to the enum itself. The define was of the MASK
that used the BIT to shift. The BIT was the enum and by adding that,
everything gets converted nicely. The MASK is still kept just in case
it gets converted to an enum in the future"
* tag 'trace-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix tick_stop tracepoint symbols for user export
Pull drm fixes from Dave Airlie:
"This contains a bunch of amdgpu fixes, and some i915 regression fixes.
It also contains some fixes for an older regression with some EDID
changes and some 6bpc panels.
Then there are the lockdep, cirrus and rcar-du regression fixes from
this window"
* tag 'drm-fixes-for-4.8-rc2' of git://people.freedesktop.org/~airlied/linux:
drm/cirrus: Fix NULL pointer dereference when registering the fbdev
drm/edid: Set 8 bpc color depth for displays with "DFP 1.x compliant TMDS".
drm/i915/dp: Revert "drm/i915/dp: fall back to 18 bpp when sink capability is unknown"
drm/edid: Add 6 bpc quirk for display AEO model 0.
drm: Paper over locking inversion after registration rework
drm: rcar-du: Link HDMI encoder with bridge
drm/ttm: Wait for a BO to become idle before unbinding it from GTT
drm/i915/fbdev: Check for the framebuffer before use
drm/amdgpu: update golden setting of polaris10
drm/amdgpu: update golden setting of stoney
drm/amdgpu: update golden setting of polaris11
drm/amdgpu: update golden setting of carrizo
drm/amdgpu: update golden setting of iceland
drm/amd/amdgpu: change pptable output format from ASCII to binary
drm/amdgpu/ci: add mullins to default case for smc ucode
drm/amdgpu/gmc7: add missing mullins case
drm/i915: Never fully mask the the EI up rps interrupt on SNB/IVB
drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL
The symbols used in the tick_stop tracepoint were not being converted
properly into integers in the trace_stop format file. Instead we had this:
print fmt: "success=%d dependency=%s", REC->success,
__print_symbolic(REC->dependency, { 0, "NONE" },
{ (1 << TICK_DEP_BIT_POSIX_TIMER), "POSIX_TIMER" },
{ (1 << TICK_DEP_BIT_PERF_EVENTS), "PERF_EVENTS" },
{ (1 << TICK_DEP_BIT_SCHED), "SCHED" },
{ (1 << TICK_DEP_BIT_CLOCK_UNSTABLE), "CLOCK_UNSTABLE" })
User space tools have no idea how to parse "TICK_DEP_BIT_SCHED" or the other
symbols used to do the bit shifting. The reason is that the conversion was
done with using the TICK_DEP_MASK_* symbols which are just macros that
convert to the BIT shift itself (with the exception of NONE, which was
converted properly, because it doesn't use bits, and is defined as zero).
The TICK_DEP_BIT_* needs to be denoted by TRACE_DEFINE_ENUM() in order to
have this properly converted for user space tools to parse this event.
Cc: stable@vger.kernel.org
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Fixes: e6e6cc22e0 ("nohz: Use enum code for tick stop failure tracing message")
Reported-by: Luiz Capitulino <lcapitulino@redhat.com>
Tested-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Bharat Kumar Gogada reported issues with the generic MSI code, where the
end-point ended up with garbage in its MSI configuration (both for the vector
and the message).
It turns out that the two MSI paths in the kernel are doing slightly different
things:
generic MSI: disable MSI -> allocate MSI -> enable MSI -> setup EP
PCI MSI: disable MSI -> allocate MSI -> setup EP -> enable MSI
And it turns out that end-points are allowed to latch the content of the MSI
configuration registers as soon as MSIs are enabled. In Bharat's case, the
end-point ends up using whatever was there already, which is not what you
want.
In order to make things converge, we introduce a new MSI domain flag
(MSI_FLAG_ACTIVATE_EARLY) that is unconditionally set for PCI/MSI. When set,
this flag forces the programming of the end-point as soon as the MSIs are
allocated.
A consequence of this is that we have an extra activate in irq_startup, but
that should be without much consequence.
tglx:
- Several people reported a VMWare regression with PCI/MSI-X passthrough. It
turns out that the patch also cures that issue.
- We need to have a look at the MSI disable interrupt path, where we write
the msg to all zeros without disabling MSI in the PCI device. Is that
correct?
Fixes: 52f518a3a7 "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts"
Reported-and-tested-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Reported-and-tested-by: Foster Snowhill <forst@forstwoof.ru>
Reported-by: Matthias Prager <linux@matthiasprager.de>
Reported-by: Jason Taylor <jason.taylor@simplivity.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1468426713-31431-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes a regression introduced by commit b810253bd9 ("cxl:
Add mechanism for delivering AFU driver specific events").
It changes the type u8 to __u8 in the uapi header cxl.h, because the
former is a kernel internal type, and may not be defined in userland
build environments, in particular when cross-compiling libcxl on x86_64
linux machines (RHEL6.7 and Ubuntu 16.04).
This patch also changes the size of the field data_size, and makes it
constant, to support 32-bit userland applications running on big-endian
ppc64 kernels transparently.
mpe: This is an ABI change, however the ABI was only added during the
4.8 merge window so has never been part of a released kernel - therefore
we give ourselves permission to change it.
Fixes: b810253bd9 ("cxl: Add mechanism for delivering AFU driver specific events")
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When I initially added the unsafe_[get|put]_user() helpers in commit
5b24a7a2aa ("Add 'unsafe' user access functions for batched
accesses"), I made the mistake of modeling the interface on our
traditional __[get|put]_user() functions, which return zero on success,
or -EFAULT on failure.
That interface is fairly easy to use, but it's actually fairly nasty for
good code generation, since it essentially forces the caller to check
the error value for each access.
In particular, since the error handling is already internally
implemented with an exception handler, and we already use "asm goto" for
various other things, we could fairly easily make the error cases just
jump directly to an error label instead, and avoid the need for explicit
checking after each operation.
So switch the interface to pass in an error label, rather than checking
the error value in the caller. Best do it now before we start growing
more users (the signal handling code in particular would be a good place
to use the new interface).
So rather than
if (unsafe_get_user(x, ptr))
... handle error ..
the interface is now
unsafe_get_user(x, ptr, label);
where an error during the user mode fetch will now just cause a jump to
'label' in the caller.
Right now the actual _implementation_ of this all still ends up being a
"if (err) goto label", and does not take advantage of any exception
label tricks, but for "unsafe_put_user()" in particular it should be
fairly straightforward to convert to using the exception table model.
Note that "unsafe_get_user()" is much harder to convert to a clever
exception table model, because current versions of gcc do not allow the
use of "asm goto" (for the exception) with output values (for the actual
value to be fetched). But that is hopefully not a limitation in the
long term.
[ Also note that it might be a good idea to switch unsafe_get_user() to
actually _return_ the value it fetches from user space, but this
commit only changes the error handling semantics ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AC100 is a multifunction device with an audio codec subsystem and
an RTC subsystem. These two subsystems share a common register space
and host interface.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A few fixes for amdgpu and ttm for 4.8
- fix a ttm regression caused by the new pipelining code
- fixes for mullins on amdgpu
- updated golden settings for amdgpu
* 'drm-next-4.8' of git://people.freedesktop.org/~agd5f/linux:
drm/ttm: Wait for a BO to become idle before unbinding it from GTT
drm/amdgpu: update golden setting of polaris10
drm/amdgpu: update golden setting of stoney
drm/amdgpu: update golden setting of polaris11
drm/amdgpu: update golden setting of carrizo
drm/amdgpu: update golden setting of iceland
drm/amd/amdgpu: change pptable output format from ASCII to binary
drm/amdgpu/ci: add mullins to default case for smc ucode
drm/amdgpu/gmc7: add missing mullins case
Pull more block fixes from Jens Axboe:
"As mentioned in the pull the other day, a few more fixes for this
round, all related to the bio op changes in this series.
Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf. I
wanted to do that change right after or right before -rc1, so that
risk of conflict was reduced. I just rebased the series on top of
current master, and no new ->bi_rw usage has snuck in"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: rename bio bi_rw to bi_opf
target: iblock_execute_sync_cache() should use bio_set_op_attrs()
mm: make __swap_writepage() use bio_set_op_attrs()
block/mm: make bdev_ops->rw_page() take a bool for read/write
Pull drm zpos property support from Dave Airlie:
"This tree was waiting on some media stuff I hadn't had time to get a
stable branchpoint off, so I just waited until it was all in your tree
first.
It's been around a bit on the list and shouldn't affect anything
outside adding the generic API and moving some ARM drivers to using
it"
* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
drm: rcar: use generic code for managing zpos plane property
drm/exynos: use generic code for managing zpos plane property
drm: sti: use generic zpos for plane
drm: add generic zpos property
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit abf545484d changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull more vfs updates from Al Viro:
"Assorted cleanups and fixes.
In the "trivial API change" department - ->d_compare() losing 'parent'
argument"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cachefiles: Fix race between inactivating and culling a cache object
9p: use clone_fid()
9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
vfs: make dentry_needs_remove_privs() internal
vfs: remove file_needs_remove_privs()
vfs: fix deadlock in file_remove_privs() on overlayfs
get rid of 'parent' argument of ->d_compare()
cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
affs ->d_compare(): don't bother with ->d_inode
fold _d_rehash() and __d_rehash() together
fold dentry_rcuwalk_invalidate() into its only remaining caller
Pull qstr constification updates from Al Viro:
"Fairly self-contained bunch - surprising lot of places passes struct
qstr * as an argument when const struct qstr * would suffice; it
complicates analysis for no good reason.
I'd prefer to feed that separately from the assorted fixes (those are
in #for-linus and with somewhat trickier topology)"
* 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
qstr: constify instances in adfs
qstr: constify instances in lustre
qstr: constify instances in f2fs
qstr: constify instances in ext2
qstr: constify instances in vfat
qstr: constify instances in procfs
qstr: constify instances in fuse
qstr constify instances in fs/dcache.c
qstr: constify instances in nfs
qstr: constify instances in ocfs2
qstr: constify instances in autofs4
qstr: constify instances in hfs
qstr: constify instances in hfsplus
qstr: constify instances in logfs
qstr: constify dentry_init_security
- New vsock device support in host and guest
- Platform IOMMU support in host and guest,
including compatibility quirks for legacy systems.
- Misc fixes and cleanups.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXofvbAAoJECgfDbjSjVRpUTIH/iEoK9h636tBayXy0PXkPby0
6fMaRFy6H1HgEttgDhJE8Pqg/ba3qaW9Em0fHyFq7Mp2waFHAZ8hAT8phC6TAK3c
CIBnfzyyuI8u3N9SnNOfelPVcwCBfuALuuTsXB/rwKbYQEVv+U5Rdt3Vyx9+lXkj
P005klz7PfqxFhQrrnj4Eh7VawtHwmMuLH8YoWpCZpM71dHPo6eL+3ftKwhH2boo
qK86uVprwba03Pewpm13vQnotemfVfUUkjXd4EJpG3dx7E0KZosuj0ZG9OV8mPGQ
Cl2gBdUhocdJgeUnAHmf6tumYi9KFlYfy6xLy44YMmN7FL3E9nQjaKZp25UKfiM=
=ztIm
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost updates from Michael Tsirkin:
- new vsock device support in host and guest
- platform IOMMU support in host and guest, including compatibility
quirks for legacy systems.
- misc fixes and cleanups.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
VSOCK: Use kvfree()
vhost: split out vringh Kconfig
vhost: detect 32 bit integer wrap around
vhost: new device IOTLB API
vhost: drop vringh dependency
vhost: convert pre sorted vhost memory array to interval tree
vhost: introduce vhost memory accessors
VSOCK: Add Makefile and Kconfig
VSOCK: Introduce vhost_vsock.ko
VSOCK: Introduce virtio_transport.ko
VSOCK: Introduce virtio_vsock_common.ko
VSOCK: defer sock removal to transports
VSOCK: transport-specific vsock_transport functions
vhost: drop vringh dependency
vop: pull in vhost Kconfig
virtio: new feature to detect IOMMU device quirk
balloon: check the number of available pages in leak balloon
vhost: lockless enqueuing
vhost: simplify work flushing
* x86 nested virt tweak and OOPS fix
* Simplify pvclock code (vdso bits acked by Andy Lutomirski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXpKOnAAoJEL/70l94x66D5z4H/R2660Vy3brQrI8lGxCtkXJt
AVe8PwI8nDfYJ/UkMZ2KcHPSvy+sHW2ydaZXYNqXHVBeTaUxiPW9rTgK61ebypGL
1tPOgJ3kGZF6XEdAz6gS8LniNFc+D3W6Y6sRylkEsqPj39/hxe7QMoOMSCQ9imbW
WMIx7/81i1EMw6oi+9FVtq+yHCpvyfFnD8t1TDsYWOReVn1J15SxbEs4Ih+hBMLz
HZ5DEjp9cAmzeR7GLje5eH1t6TEEoNb1MNgFWuscoAsDf8D9DKqRB9s0hC+TLFYn
oZbGSqjQwu3/VMblgedinH6X9MTm8V0zW29ToGnDcoO00AUmdlNmXSaZUhvT/Rs=
=H5cD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
- ARM bugfix and MSI injection support
- x86 nested virt tweak and OOPS fix
- Simplify pvclock code (vdso bits acked by Andy Lutomirski).
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
nvmx: mark ept single context invalidation as supported
nvmx: remove comment about missing nested vpid support
KVM: lapic: fix access preemption timer stuff even if kernel_irqchip=off
KVM: documentation: fix KVM_CAP_X2APIC_API information
x86: vdso: use __pvclock_read_cycles
pvclock: introduce seqcount-like API
arm64: KVM: Set cpsr before spsr on fault injection
KVM: arm: vgic-irqfd: Workaround changing kvm_set_routing_entry prototype
KVM: arm/arm64: Enable MSI routing
KVM: arm/arm64: Enable irqchip routing
KVM: Move kvm_setup_default/empty_irq_routing declaration in arch specific header
KVM: irqchip: Convey devid to kvm_set_msi
KVM: Add devid in kvm_kernel_irq_routing_entry
KVM: api: Pass the devid in the msi routing entry
This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom iProc,
STMPE and ChromeOS EC controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TdEI
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom
iProc, STMPE and ChromeOS EC controllers"
* tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
regulator: pwm: Document pwm-dutycycle-unit and pwm-dutycycle-range
regulator: pwm: Support extra continuous mode cases
pwm: Add ChromeOS EC PWM driver
dt-bindings: pwm: Add binding for ChromeOS EC PWM
mfd: cros_ec: Add EC_PWM function definitions
mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
pwm: atmel: Use of_device_get_match_data()
pwm: atmel: Fix checkpatch warnings
pwm: atmel: Fix disabling of PWM channels
dt-bindings: pwm: Add R-Car H3 device tree bindings
pwm: rcar: Use ARCH_RENESAS
pwm: tegra: Add support for Tegra186
dt-bindings: pwm: tegra: Add compatible string for Tegra186
pwm: tegra: Avoid overflow when calculating duty cycle
pwm: tegra: Allow 100 % duty cycle
pwm: tegra: Add support for reset control
pwm: tegra: Rename mmio_base to regs
pwm: tegra: Remove useless padding
pwm: tegra: Drop NUM_PWM macro
pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value
...
Pull block fixes from Jens Axboe:
"Here's the second round of block updates for this merge window.
It's a mix of fixes for changes that went in previously in this round,
and fixes in general. This pull request contains:
- Fixes for loop from Christoph
- A bdi vs gendisk lifetime fix from Dan, worth two cookies.
- A blk-mq timeout fix, when on frozen queues. From Gabriel.
- Writeback fix from Jan, ensuring that __writeback_single_inode()
does the right thing.
- Fix for bio->bi_rw usage in f2fs from me.
- Error path deadlock fix in blk-mq sysfs registration from me.
- Floppy O_ACCMODE fix from Jiri.
- Fix to the new bio op methods from Mike.
One more followup will be coming here, ensuring that we don't
propagate the block types outside of block. That, and a rename of
bio->bi_rw is coming right after -rc1 is cut.
- Various little fixes"
* 'for-linus' of git://git.kernel.dk/linux-block:
mm/block: convert rw_page users to bio op use
loop: make do_req_filebacked more robust
loop: don't try to use AIO for discards
blk-mq: fix deadlock in blk_mq_register_disk() error path
Include: blkdev: Removed duplicate 'struct request;' declaration.
Fixup direct bi_rw modifiers
block: fix bdi vs gendisk lifetime mismatch
blk-mq: Allow timeouts to run while queue is freezing
nbd: fix race in ioctl
block: fix use-after-free in seq file
f2fs: drop bio->bi_rw manual assignment
block: add missing group association in bio-cloning functions
blkcg: kill unused field nr_undestroyed_grps
writeback: Write dirty times for WB_SYNC_ALL writeback
floppy: fix open(O_ACCMODE) for ioctl-only open
Pull more input updates from Dmitry Torokhov:
"Two new drivers for touchscreen controllers:
- Silead touchscreen controllers
- SiS 9200 family touchscreen controllers
and a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: silead - remove some dead code
Input: sis-i2c - select CONFIG_CRC_ITU_T
Input: add driver for SiS 9200 family I2C touchscreen controllers
Input: ili210x - fix permissions on "calibrate" attribute
Input: elan_i2c - properly wake up touchpad on ASUS laptops
Input: add driver for Silead touchscreens
Input: elantech - fix debug dump of the current packet
Input: rotary_encoder - support binary encoding of states
Input: xpad - power off wireless 360 controllers on suspend
Input: i8042 - break load dependency between atkbd/psmouse and i8042
Input: synaptics-rmi4 - do not check for NULL when calling of_node_put()
Input: cros_ec_keyb - cleanup use of dev
We don't want to miss a lease period renewal due to the TCP connection
failing to reconnect in a timely fashion. To ensure this doesn't happen,
cap the reconnection timer so that we retry the connection attempt
at least every 1/2 lease period.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
