The local variable search in regulator_of_get_init_node takes the value
returned by either of_get_child_by_name or of_node_get, both of which
get a node. If this node is not put before returning, it could cause a
memory leak. Hence put search before a mid-loop return statement.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190724083231.10276-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "ti,lp87565" compatible string is still in of_lp87565_match_table,
but current code will return -EINVAL because lp87565->dev_type is unknown.
This was working in earlier kernel versions, so fix it.
Fixes: 7ee63bd747 ("regulator: lp87565: Add 4-phase lp87561 regulator support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190711113517.26077-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactoring of axp20x driver introduced a bug in AXP803's DCDC6
regulator definition. AXP803_DCDC6_1120mV_STEPS was obtained by
subtracting 0x47 and 0x33. This should be 0x14 (hex) and not 14
(dec).
Refactoring also carried over a bug in DCDC5 regulator definition.
Number of possible voltages must be for 1 bigger than maximum valid
voltage index, because 0 is also valid and it means lowest voltage.
Fixes: 1dbe0ccb06 ("regulator: axp20x-regulator: add support for AXP803")
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20190713090717.347-3-jernej.skrabec@siol.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactoring of the driver introduced bugs in AXP806's DCDCA and DCDCD
regulator definitions.
In DCDCA case, AXP806_DCDCA_1120mV_STEPS was obtained by subtracting
0x47 and 0x33. This should be 0x14 (hex) and not 14 (dec).
In DCDCD case, axp806_dcdcd_ranges[] contains two ranges with same
start and end macros, which is clearly wrong. Second range starts at
1.6V so it should use AXP806_DCDCD_1600mV_[START|END] macros. They are
already defined but unused.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20190713090717.347-2-jernej.skrabec@siol.net
Signed-off-by: Mark Brown <broonie@kernel.org>
- Set 'struct device' fwnode when registering a new device
- New Drivers
- Add support for ROHM BD70528 PMIC
- New Device Support
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
- New Functionality
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
- Fix-ups
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
- Bug Fixes
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera
-----BEGIN PGP SIGNATURE-----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=A3jw
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Set 'struct device' fwnode when registering a new device
New Drivers:
- Add support for ROHM BD70528 PMIC
New Device Support:
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
New Functionality:
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
Fix-ups:
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
Bug Fixes:
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera"
* tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: hi655x-pmic: Fix missing return value check for devm_regmap_init_mmio_clk
mfd: madera: Fixup SPDX headers
mfd: madera: Remove some unused registers and fix some defaults
mfd: intel-lpss: Release IDA resources
mfd: intel-lpss: Add Intel Elkhart Lake PCH PCI IDs
mfd: cs5535-mfd: Remove ifdef OLPC noise
mfd: stmfx: Fix macro definition spelling
dt-bindings: mfd: Add link to ROHM BD71847 Datasheet
MAINAINERS: Swap words in INTEL PMIC MULTIFUNCTION DEVICE DRIVERS
mfd: cros_ec_dev: Register cros_ec_accel_legacy driver as a subdevice
mfd: rk808: Prepare rk805 for poweroff
mfd: rk808: Check pm_power_off pointer
mfd: cros_ec: differentiate SCP from EC by feature bit
dt-bindings: Add binding for cros-ec-rpmsg
mfd: madera: Add Madera core support for CS47L92
mfd: madera: Add Madera core support for CS47L15
mfd: madera: Update DT bindings to add additional CODECs
mfd: madera: Add supply mapping for MICVDD
mfd: madera: Fix potential uninitialised use of variable
mfd: madera: Fix bad reference to pinctrl.txt file
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
A couple of new features in the core, the most interesting one
being support for complex regulator coupling configurations
initially targeted at nVidia Tegra SoCs, and some new drivers but
otherwise quite a quiet release.
- Core support for gradual ramping of voltages for devices that
can't manage large changes in hardware from Bartosz Golaszewski.
- Core support for systems that have complex coupling requirements
best described via code, contributed by Dmitry Osipenko.
- New drivers for Dialog SLG51000, Qualcomm PM8005 and ST
Microelectronics STM32-Booster.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl0jIZwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PG+B/9EQnjM29THpBKM6bKdl8cYcf3Hq/FX
KNtXjwaTM0DqYtpk1RkaHgecxTJwesJ0k9AYijh0ieeMhb5UES280+6B4NqPb7xr
UmFBbNcdk9G+x9q1TyT8akRMkCugEMscQodyk4npzZRjGv8qUsNJUY71Bq2T/JJx
QXo5fKlWICzBahF87DCB5pKC7PKfNkx3BWCrGGXOqoBX2ZEKytyWlCa0nGUZ+LqL
GqXmmIjKL7H8MP3avmrrRHYpeF5DLXAzH+HEIM9Y0F1cRcdgOS1Exv2eG+90a634
yybVDBX2d5zfiEIoRnpldtB52EGXjvwbo7w1mFwh9UgJRbOCZgb+ZQXT
=26r6
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A couple of new features in the core, the most interesting one being
support for complex regulator coupling configurations initially
targeted at nVidia Tegra SoCs, and some new drivers but otherwise
quite a quiet release.
Summary:
- Core support for gradual ramping of voltages for devices that can't
manage large changes in hardware from Bartosz Golaszewski.
- Core support for systems that have complex coupling requirements
best described via code, contributed by Dmitry Osipenko.
- New drivers for Dialog SLG51000, Qualcomm PM8005 and ST
Microelectronics STM32-Booster"
* tag 'regulator-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (52 commits)
regulator: max77650: use vsel_step
regulator: implement selector stepping
regulator: max77650: add MODULE_ALIAS()
regulator: max77620: remove redundant assignment to variable ret
dt-bindings: regulator: add support for the stm32-booster
regulator: add support for the stm32-booster
regulator: s2mps11: Adjust supported buck voltages to real values
regulator: s2mps11: Fix buck7 and buck8 wrong voltages
gpio: Fix return value mismatch of function gpiod_get_from_of_node()
regulator: core: Expose some of core functions needed by couplers
regulator: core: Introduce API for regulators coupling customization
regulator: s2mps11: Add support for disabling S2MPS11 regulators in suspend
regulator: s2mps11: Reduce number of rdev_get_id() calls
regulator: qcom_spmi: Do NULL check for lvs
regulator: qcom_spmi: Fix math of spmi_regulator_set_voltage_time_sel
regulator: da9061/62: Adjust LDO voltage selection minimum value
regulator: s2mps11: Fix ERR_PTR dereference on GPIO lookup failure
regulator: qcom_spmi: add PMS405 SPMI regulator
dt-bindings: qcom_spmi: Document pms405 support
arm64: dts: msm8998-mtp: Add pm8005_s1 regulator
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXRozKAAKCRBiEGxRG/Sl
25okAP9I0Rmscpqjb/+GEeXH4EmL3moGzc9o/BzHRqfeO4wqYAEA+8f7L20xHe8g
tvEGfP7mN/oBmcAfqgH5K9F4eJsBRAw=
=NkCn
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- Add a new LED common module for ti-lmu driver family
- Modify MFD ti-lmu bindings
- add ti,brightness-resolution
- add the ramp up/down property
- Add regulator support for LM36274 driver to lm363x-regulator.c
- New LED class drivers with DT bindings:
- leds-spi-byte
- leds-lm36274
- leds-lm3697 (move the support from MFD to LED subsystem)
- Simplify getting the I2C adapter of a client:
- leds-tca6507
- leds-pca955x
- Convert LED documentation to ReST
* tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
dt: leds-lm36274.txt: fix a broken reference to ti-lmu.txt
docs: leds: convert to ReST
leds: leds-tca6507: simplify getting the adapter of a client
leds: leds-pca955x: simplify getting the adapter of a client
leds: lm36274: Introduce the TI LM36274 LED driver
dt-bindings: leds: Add LED bindings for the LM36274
regulator: lm363x: Add support for LM36274
mfd: ti-lmu: Add LM36274 support to the ti-lmu
dt-bindings: mfd: Add lm36274 bindings to ti-lmu
leds: max77650: Remove set but not used variable 'parent'
leds: avoid flush_work in atomic context
leds: lm3697: Introduce the lm3697 driver
mfd: ti-lmu: Remove support for LM3697
dt-bindings: ti-lmu: Modify dt bindings for the LM3697
leds: TI LMU: Add common code for TI LMU devices
leds: spi-byte: add single byte SPI LED driver
dt-bindings: leds: Add binding for spi-byte LED.
dt-bindings: mfd: LMU: Add ti,brightness-resolution
dt-bindings: mfd: LMU: Add the ramp up/down property
Use the new vsel_step field in the regulator description to instruct
the regulator API on the required voltage ramping. Switch to using the
generic regmap helpers for voltage setting and remove the old set_voltage
callback that handcoded the selector stepping.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190703161035.31808-3-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators require that the requested voltage be reached gradually
by setting all or some of the intermediate values. Implement a new field
in the regulator description struct that allows users to specify the
number of selectors by which the regulator API should step when ramping
the voltage up/down.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190703161035.31808-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Define a MODULE_ALIAS() in the regulator sub-driver for max77650 so that
the appropriate module gets loaded together with the core mfd driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190703084849.9668-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable ret is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190703082009.18779-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the 3.3V booster regulator embedded in stm32h7 and stm32mp1
devices, that can be used to supply ADC analog input switches.
This regulator is supplied by vdda. It's controlled by using SYSCFG:
- STM32H7 has a unique register to set/clear the booster enable bit
- STM32MP1 has separate set and clear registers to configure it.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was registering buck regulators with unsupported range of
voltages for S2MPS11 devices. Basically it assumed that all 256 values
are possible for a single 8-bit I2C register controlling buck's voltage.
This is not true, as datasheet describes subset of these which can be
used.
For example for buck[12346] the minimum voltage is 650 mV which
corresponds to register value of 0x8. The driver was however
registering regulator starting at 600 mV, so for a step of 6.25 mV this
gave the same result. However this allowed to try to configure
regulators to unsupported values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750
mV, not 600 mV. Using wrong minimal value caused shifting of these
regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was
reported as 1.2 V).
On most of the boards these regulators are left in default state so this
was only affecting reported voltage. However if any driver wanted to
change them, then effectively it would set voltage 150 mV higher than
intended.
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the LP87565_DEVICE_TYPE_LP87561_Q1 case does not have a
break statement, causing it to fall through to a dev_err message.
Fix this by adding in the missing break statement.
Addresses-Coverity: ("Missing break in switch")
Fixes: 7ee63bd747 ("regulator: lp87565: Add 4-phase lp87561 regulator support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the rk809 and rk817 regulator driver.
Their specifications are as follows：
1. The RK809 and RK809 consist of 5 DCDCs, 9 LDOs
and have the same registers for these components except dcdc5.
2. The dcdc5 is a boost dcdc for RK817 and is a buck for RK809.
3. The RK817 has one switch but The Rk809 has two.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Acked-by: Mark Brown <broonie@kernel.org>
[rebased on top of 5.2-rc1]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Split the bd718x7.h to ROHM common and bd718x7 specific parts
so that we do not need to add same things in every new ROHM
PMIC header. Please note that this change requires changes also
in bd718x7 sub-device drivers for regulators and clk.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In case the requested gpio property is not found in the device tree, some
callers of gpiod_get_from_of_node() expect a return value of NULL, others
expect -ENOENT.
In particular devm_fwnode_get_index_gpiod_from_child() expects -ENOENT.
Currently it gets a NULL, which breaks the loop that tries all
gpio_suffixes. The result is that a gpio property is not found, even
though it is there.
This patch changes gpiod_get_from_of_node() to return -ENOENT instead
of NULL when the requested gpio property is not found in the device
tree. Additionally it modifies all calling functions to properly
evaluate the return value.
Another approach would be to leave the return value of
gpiod_get_from_of_node() as is and fix the bug in
devm_fwnode_get_index_gpiod_from_child(). Other callers would still need
to be reworked. The effort would be the same as with the chosen solution.
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Expose some of internal functions that are required for implementation of
customized regulator couplers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Right now regulator core supports only one type of regulators coupling,
the "voltage max-spread" which keeps voltages of coupled regulators in a
given range from each other. A more sophisticated coupling may be required
in practice, one example is the NVIDIA Tegra SoCs which besides the
max-spreading have other restrictions that must be adhered. Introduce API
that allow platforms to provide their own customized coupling algorithms.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver supported turning off regulators in suspend only for S2MPS14
device. However this makes also sense for S2MPS11 and can reduce the
power consumption during suspend to RAM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Store the regulator ID instead of calling rdev_get_id() every time.
This makes code slightly easier to read as shorter 'rdev_id' variable is
used instead of full call. This can also speed things up by reducing
number of calls, although effect was not measured.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Low-voltage switches (lvs) don't have set_points since the voltage ranges
of the output are really controlled by the inputs. This is a problem for
the newly added linear range support in the probe(), as that will cause
a null pointer dereference error on older platforms like msm8974 which
happen to need to control some of the implemented lvs.
Fix this by adding the appropriate null check.
Fixes: 86f4ff7a0c ("regulator: qcom_spmi: enable linear range info")
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
spmi_regulator_set_voltage_time_sel() calculates the amount of delay
needed as the result of setting a new voltage. Essentially this is the
absolute difference of the old and new voltages, divided by the slew rate.
The implementation of spmi_regulator_set_voltage_time_sel() is wrong.
It attempts to calculate the difference in voltages by using the
difference in selectors and multiplying by the voltage step between
selectors. This ignores the possibility that the old and new selectors
might be from different ranges, which have different step values. Also,
the difference between the selectors may encapsulate N ranges inbetween,
so a summation of each selector change from old to new would be needed.
Lets avoid all of that complexity, and just get the actual voltage
represented by both the old and new selector, and use those to directly
compute the voltage delta. This is more straight forward, and has the
side benifit of avoiding issues with regulator implementations that don't
have hardware register support to get the current configured range.
Fixes: e92a404741 ("regulator: Add QCOM SPMI regulator driver")
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reported-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the DA9061 and DA9062 datasheets the LDO voltage selection
registers have a lower value of 0x02. This applies to voltage registers
VLDO1_A, VLDO2_A, VLDO3_A and VLDO4_A. This linear offset of 0x02 was
previously not observed by the driver, causing the LDO output voltage to
be systematically lower by two steps (= 0.1V).
This patch fixes the minimum linear selector offset by setting it to a
value of 2 and increases the n_voltages by the same amount allowing
voltages in the range 0x02 -> 0.9V to 0x38 -> 3.6V to be correctly
selected. Also fixes an incorrect calculaton for the n_voltages value in
the regulator LDO2.
These fixes effect all LDO regulators for DA9061 and DA9062.
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Felix Riemann <felix.riemann@sma.de>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If devm_gpiod_get_from_of_node() call returns ERR_PTR, it is assigned
into an array of GPIO descriptors and used later because such error is
not treated as critical thus it is not propagated back to the probe
function.
All code later expects that such GPIO descriptor is either a NULL or
proper value. This later might lead to dereference of ERR_PTR.
Only devices with S2MPS14 flavor are affected (other do not control
regulators with GPIOs).
Fixes: 1c984942f0 ("regulator: s2mps11: Pass descriptor instead of GPIO number")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PMS405 has 5 HFSMPS and 13 LDO regulators,
This commit adds support for one of the 5 HFSMPS regulators (s3) to
the spmi regulator driver.
The PMIC HFSMPS 430 regulators have 8 mV step size and a voltage
control scheme consisting of two 8-bit registers defining a 16-bit
voltage set point in units of millivolts
S3 controls the cpu voltages (s3 is a buck regulator of type HFS430);
it is therefore required so we can enable voltage scaling for safely
running cpufreq.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM8005 is used on the msm8998 MTP. The S1 regulator is VDD_GFX, ie
it needs to be on and controlled inorder to use the GPU. Add support to
drive the PM8005 regulators so that we can bring up the GPU on msm8998.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
spmi_regulator_common_get_mode and spmi_regulator_common_set_mode use
multi-level ifs which mirror a switch statement. Refactor to use a switch
statement to make the code flow more clear.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The LP8756x family has a single output 4-phase regulator
configuration. Add support for the same. The control
lies in the master buck which is buck0 for 4-phase
configuration. Enable/disable/voltage set happen via
buck0 registers.
Data Sheet: https://www.ti.com/lit/ds/symlink/lp87561-q1.pdf
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The conversion here is really trivial: just a bunch of title
markups and very few puntual changes is enough to make it to
be parsed by Sphinx and generate a nice html.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This finalizes the descriptor conversion of the MAX8952 driver
by letting the VID0 and VID1 GPIOs be fetched from descriptors.
Both VID0 and VID1 must be supplied for the VID selection to work,
I add some code to preserve the semantics that if only one of
the two VID gpios is supplied, it will be initialized to low.
This might be a bit overzealous, but I want to preserve any
implicit semantics.
This is currently only used by device tree in-kernel but it is
still also possible to supply the same GPIOs using a machine
descriptor table if a board file is used.
Ideally this should be phased over to using gpio-regulator.c
that does the same thing, but it might require some refactoring
and needs testing on real hardware.
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building with CONFIG_MFD_88PM800 and CONFIG_REGULATOR_88PM800
enabled as loadable modules, we see the following warning:
warning: same module names found:
drivers/regulator/88pm800.ko
drivers/mfd/88pm800.ko
Rework so that the file is named 88pm800-regulator.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the Wolfson Micro WM831x DCDC converter to use
a GPIO descriptor for the GPIO driving the DVS pin.
There is just one (non-DT) machine in the kernel using this, and
that is the Wolfson Micro (now Cirrus) Cragganmore 6410 so we
patch this board to pass a descriptor table and fix up the driver
accordingly.
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: patches@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just one driver specific fix here, for a boot regression introduced
during some modernization work on the tps6507x driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlz+aOcTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PtiB/96XSSJtLQxArYN2tnTPzeq2asZK3y6
nH1r+d9GAbAj8rIzO9qRSEz/x9oZcikYqR2QdyXSI4pJNH+KRbNpktMTq5HHtm7E
9KNRtz8Ni4dR6Paz04vWA2gUaEps5uMCMDKk38gnL21PLQlaaAn4M0TN/iBBLdgR
8n8tTgPez6gyqtZZ17cwyHAKh4z7Vln5Ps+dyHwLbbzXg0RFwGwRXXIVLFfnGu9E
euBinP6MS3SYvbgnas0+5uXbpGNhXeVPSKnP+muRvTkCs9TxjgV55IUhrWaxXb3+
mrhgElvZ45AwqpQbyQ1+dW7nXQhzFLK6YCVD25BfNe5iq4o1GAjI61CJ
=Dz+r
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"Just one driver specific fix here, for a boot regression introduced
during some modernization work on the tps6507x driver"
* tag 'regulator-fix-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps6507x: Fix boot regression due to testing wrong init_data pointer
This driver does not use any symbols from <linux/gpio.h>
no <linux/gpio/consumer.h> so just drop the includes.
Cc: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding regulator support for the LM36274 backlight driver.
This device can leverage this existing code as the functionality
and registers are common enough between the LM36274 and the LM363x
series of devices.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published bythe free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190116.345887520@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nishka Dasgupta