Use "new" start address register 0x69 (bits 16-20) instead of "old" 0x31
(bits 16-17) and 0x51 (bits 18-19). This is needed for panning to work
correctly on Trio3D/2X cards (and does no harm on other ones).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable Data Transfer Position Control (DTPC). This is needed at least on
Virge/DX to correctly display at higher pixclocks.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable pixel multiplexing in 15/16bpp modes when pixclock is over 115MHz
on Trio3D (86C365) cards to fix artifacts on the left side of screen.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for S3 Trio3D (86C365) cards to s3fb driver. Tested with one 4MB card.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Maximize virtual vertical framebuffer size during init to allow fast scrolling
(accelerated by panning).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows the driver to work in multi-domain PCI
configurations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows the driver to work in multi-domain PCI
configurations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows the driver to work in multi-domain PCI
configurations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for ZGI Z9 DDR2 POST. The init sequence is from XGI's
xgifb driver.
Tested with ARM board using a PCI card with XGI Z9s and 32 MB DDR2
memory. After a cold reset the POST succeeds.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move DDR2 register setting code into separate subroutines. No changes
in functionality.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Detect the XGI Z9 RAM type as "documented" by the XGI's xgifb driver.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Z7 and Z9 have the same PCI ID, so additional checking is needed to
detect Z9. The method was "documented" in XGI's xgifb driver.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move XGI POST RAM type detection into a separate subroutine to make
further code changes easier. No changes in functionality
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently there is no indication if R/W test fails during POST. This can
happen e.g. when user plugs in a card with unsupported type of memory.
Since the driver will be unusable, it's better to fail the whole POST
if the memory cannot be configured properly.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove incorrect Matrox G200eV support that was previously added by
commit e3a1938805
A serious issue with the incorrect G200eV support that reproduces on the
Matrox G200eV equipped IBM x3650 M2 is the total lack of text (login
banner, login prompt, etc) on the console when X is not running and
total lack of text on all of the virtual consoles after X is started.
Any concerns that the incorrect code (upstream since October 2008) has
been successfully used on non-IBM G200eV equipped system(s) appear to be
unwarranted. In addition to the serious/non-intermittent nature of
issues that have been spotted on IBM systems, complete removal of the
incorrect code is clearly supported by the following Matrox (Yannick
Heneault) provided input:
"It impossible that this patch should have work on a system.
The patch only declare the G200eV as a regular G200 which is
not case. Many registers are different, including at least the
PLL programming sequence. If the G200eV is programmed like a
regular G200, it will not display anything."
v1 - Initial patch that removed the incorrect code for _all_
G200eV equipped systems.
v2 - Darrick Wong provided patch that blacklisted the incorrect
code on G200eV equipped IBM systems leaving it enabled on
all G200eV equipped non-IBM systems.
v3 - Same code changes included with v1 plus additional
justification for complete removal of the incorrect code.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Yannick Heneault <yannick_heneault@matrox.com>
Cc: Christian Toutant <ctoutant@matrox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
video: change to new flag variable
scsi: change to new flag variable
rtc: change to new flag variable
rapidio: change to new flag variable
pps: change to new flag variable
net: change to new flag variable
misc: change to new flag variable
message: change to new flag variable
memstick: change to new flag variable
isdn: change to new flag variable
ieee802154: change to new flag variable
ide: change to new flag variable
hwmon: change to new flag variable
dma: change to new flag variable
char: change to new flag variable
fs: change to new flag variable
xtensa: change to new flag variable
um: change to new flag variables
s390: change to new flag variable
mips: change to new flag variable
...
Fix up trivial conflict in drivers/hwmon/Makefile
Add dss.dpll4_m4_ck (DSS FCLK) initialization for OMAP4. This is used
to compute the pixel clock for DPI interface and also to reconfigure
the DSS FCLK to the desired rate, corresponding to the rate computed
for pixel clock.
Adding these cpu_is_44xx() checks are meant to be temporary, until a
cleaner implementation to manage these checks are added. Currently this
is needed to get DVI display running on OMAP4 PandaBoard
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
[tomi.valkeinen@ti.com: minor changes due to conflicts]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP2 does not have dpll4_m4_ck source clock for dss functional clock,
but later OMAPs do. Currently we check for cpu type in multiple places
to find out if dpll4_m4_ck is available.
This patch cleans up dss.c by using the fact that dss.dpll4_m4_ck
pointer is NULL on OMAP2. This allows us to remove many of the cpu
checks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (46 commits)
msm: scm: Check for interruption immediately
msm: scm: Fix improper register assignment
msm: scm: Mark inline asm as volatile
msm: iommu: Enable HTW L2 redirection on MSM8960
msm: iommu: Don't read from write-only registers
msm: iommu: Remove dependency on IDR
msm: iommu: Use ASID tagging instead of VMID tagging
msm: iommu: Rework clock logic and add IOMMU bus clock control
msm: iommu: Clock control for the IOMMU driver
msm: mdp: Set the correct pack pattern for XRGB/ARGB
msm_fb: Fix framebuffer console
msm: mdp: Add support for RGBX 8888 image format.
video: msmfb: Put the partial update magic value into the fix_screen struct.
msm: clock: Migrate to clkdev
msm: clock: Remove references to clk_ops_pcom
msm: headsmp.S: Fix section mismatch
msm: Use explicit GPLv2 licenses
msm: iommu: Enable IOMMU support for MSM8960
msm: iommu: Generalize platform data for multiple targets
msm: iommu: Create a Kconfig item for the IOMMU driver
...
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32: (40 commits)
unicore32: rewrite arch-specific tlb.h to use asm-generic version
unicore32: modify io_p2v and io_v2p macros, and adjust PKUNITY_mmio_BASEs
unicore32: replace unicore32-specific iomap functions with generic lib implementation
unicore32 machine related: add frame buffer driver for pkunity-v3 soc
unicore32 machine related files: add i2c bus drivers for pkunity-v3 soc
unicore32 io: redefine __REG(x) and re-use readl/writel funcs
unicore32 i8042 upgrade and bugfix: adjust resource request region type
unicore32 upgrade to v2.6.38-rc5: add one more paramter for pte_alloc_map call
unicore32 i8042: adjust io funcs of i8042-unicore32io.h
unicore32: rename PKUNITY_IOSPACE_BASE to PKUNITY_MMIO_BASE
unicore32: modify function names and parameters for irq_chips
unicore32: remove unused lines in arch/unicore32/include/asm/irq.h
unicore32 time.c: change calculate method for clock_event_device
unicore32: ADD MAINTAINER for unicore32 architecture
unicore32 machine related files: ps2 driver
unicore32 machine related files: pci bus handling
unicore32 machine related files: hardware registers
unicore32 machine related files: core files
unicore32 additional architecture files: boot process
unicore32 additional architecture files: low-level lib: misc
...
Acked-by: Arnd Bergmann <arnd@arndb.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
fbdev: sh_mobile_lcdc: Add YUV framebuffer support
viafb: split pll configs up
viafb: remove duplicated clock storage
viafb: always return the best possible clock
viafb: remove duplicated clock information
fbdev: sh_mobile_lcdcfb: add backlight support
viafb: factor lcd scaling parameters out
viafb: strip some structures
viafb: remove unused data_mode and device_type
viafb: kill lcd_panel_id
video via: make local variables static
video via: fix iomem access
video/via: drop deprecated (and unused) i2c_adapter.id
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
change from original version -- by advice of Paul Mundt
1. remove videomemorysize definitions
2. remove unifb_enable and unifb_setup
3. use dev_warn instead of printk in fb driver
4. remove judgement for FB_ACCEL_PUV3_UNIGFX
5. adjust clk_get and clk_set_rate calls
6. add resources definitions
7. remove unifb_option
8. adjust register for platform_device
9. adjust unifb_ops position and unifb_regs assignment position
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
