Nobody is using sched_clock_func() anymore now that sched_clock
supports up to 64 bits. Remove the hook so that new code only
uses sched_clock_register().
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The ARM architected system counter has at least 56 usable bits.
Add support for counters with more than 32 bits to the generic
sched_clock implementation so we can increase the time between
wakeups due to dealing with wrap-around on these devices while
benefiting from the irqtime accounting and suspend/resume
handling that the generic sched_clock code already has. On my
system using 56 bits over 32 bits changes the wraparound time
from a few minutes to an hour. For faster running counters (GHz
range) this is even more important because we may not be able to
execute the timer in time to deal with the wraparound if only 32
bits are used.
We choose a maxsec value of 3600 seconds because we assume no
system will go idle for more than an hour. In the future we may
need to increase this value.
Note: All users should switch over to the 64-bit read function so
we can remove setup_sched_clock() in favor of sched_clock_register().
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In the next patch we're going to increase the number of bits that
the generic sched_clock can handle to be greater than 32. With
more than 32 bits the wraparound time can be larger than what can
fit into the units that msecs_to_jiffies takes (unsigned int).
Luckily, the wraparound is initially calculated in nanoseconds
which we can easily use with hrtimers, so switch to using an
hrtimer.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Fixup hrtimer intitialization order issue]
Signed-off-by: John Stultz <john.stultz@linaro.org>
We're going to increase the cyc value to 64 bits in the near
future. Doing that is going to break the custom seqcount
implementation in the sched_clock code because 64 bit numbers
aren't guaranteed to be atomic. Replace the cyc_copy with a
seqcount to avoid this problem.
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
There is a small race between when the cycle count is read from
the hardware and when the epoch stabilizes. Consider this
scenario:
CPU0 CPU1
---- ----
cyc = read_sched_clock()
cyc_to_sched_clock()
update_sched_clock()
...
cd.epoch_cyc = cyc;
epoch_cyc = cd.epoch_cyc;
...
epoch_ns + cyc_to_ns((cyc - epoch_cyc)
The cyc on cpu0 was read before the epoch changed. But we
calculate the nanoseconds based on the new epoch by subtracting
the new epoch from the old cycle count. Since epoch is most likely
larger than the old cycle count we calculate a large number that
will be converted to nanoseconds and added to epoch_ns, causing
time to jump forward too much.
Fix this problem by reading the hardware after the epoch has
stabilized.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
2013-06-12 14:02:13 -07:00
Renamed from arch/arm/kernel/sched_clock.c (Browse further)