In fib6_add(), it is possible that fib6_add_1() picks an intermediate
node and sets the node's fn->leaf to NULL in order to add this new
route. However, if fib6_add_rt2node() fails to add the new
route for some reason, fn->leaf will be left as NULL and could
potentially cause crash when fn->leaf is accessed in fib6_locate().
This patch makes sure fib6_repair_tree() is called to properly repair
fn->leaf in the above failure case.
Here is the syzkaller reported general protection fault in fib6_locate:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 0 PID: 40937 Comm: syz-executor3 Not tainted
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task: ffff8801d7d64100 ti: ffff8801d01a0000 task.ti: ffff8801d01a0000
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] __ipv6_prefix_equal64_half include/net/ipv6.h:475 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] ipv6_prefix_equal include/net/ipv6.h:492 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] fib6_locate_1 net/ipv6/ip6_fib.c:1210 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] fib6_locate+0x281/0x3c0 net/ipv6/ip6_fib.c:1233
RSP: 0018:ffff8801d01a36a8 EFLAGS: 00010202
RAX: 0000000000000020 RBX: ffff8801bc790e00 RCX: ffffc90002983000
RDX: 0000000000001219 RSI: ffff8801d01a37a0 RDI: 0000000000000100
RBP: ffff8801d01a36f0 R08: 00000000000000ff R09: 0000000000000000
R10: 0000000000000003 R11: 0000000000000000 R12: 0000000000000001
R13: dffffc0000000000 R14: ffff8801d01a37a0 R15: 0000000000000000
FS: 00007f6afd68c700(0000) GS:ffff8801db400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004c6340 CR3: 00000000ba41f000 CR4: 00000000001426f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
ffff8801d01a37a8 ffff8801d01a3780 ffffed003a0346f5 0000000c82a23ea0
ffff8800b7bd7700 ffff8801d01a3780 ffff8800b6a1c940 ffffffff82a23ea0
ffff8801d01a3920 ffff8801d01a3748 ffffffff82a223d6 ffff8801d7d64988
Call Trace:
[<ffffffff82a223d6>] ip6_route_del+0x106/0x570 net/ipv6/route.c:2109
[<ffffffff82a23f9d>] inet6_rtm_delroute+0xfd/0x100 net/ipv6/route.c:3075
[<ffffffff82621359>] rtnetlink_rcv_msg+0x549/0x7a0 net/core/rtnetlink.c:3450
[<ffffffff8274c1d1>] netlink_rcv_skb+0x141/0x370 net/netlink/af_netlink.c:2281
[<ffffffff82613ddf>] rtnetlink_rcv+0x2f/0x40 net/core/rtnetlink.c:3456
[<ffffffff8274ad38>] netlink_unicast_kernel net/netlink/af_netlink.c:1206 [inline]
[<ffffffff8274ad38>] netlink_unicast+0x518/0x750 net/netlink/af_netlink.c:1232
[<ffffffff8274b83e>] netlink_sendmsg+0x8ce/0xc30 net/netlink/af_netlink.c:1778
[<ffffffff82564aff>] sock_sendmsg_nosec net/socket.c:609 [inline]
[<ffffffff82564aff>] sock_sendmsg+0xcf/0x110 net/socket.c:619
[<ffffffff82564d62>] sock_write_iter+0x222/0x3a0 net/socket.c:834
[<ffffffff8178523d>] new_sync_write+0x1dd/0x2b0 fs/read_write.c:478
[<ffffffff817853f4>] __vfs_write+0xe4/0x110 fs/read_write.c:491
[<ffffffff81786c38>] vfs_write+0x178/0x4b0 fs/read_write.c:538
[<ffffffff817892a9>] SYSC_write fs/read_write.c:585 [inline]
[<ffffffff817892a9>] SyS_write+0xd9/0x1b0 fs/read_write.c:577
[<ffffffff82c71e32>] entry_SYSCALL_64_fastpath+0x12/0x17
Note: there is no "Fixes" tag as this seems to be a bug introduced
very early.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we know in some target's checkentry it may dereference par.entryinfo
to check entry stuff inside. But when sched action calls xt_check_target,
par.entryinfo is set with NULL. It would cause kernel panic when calling
some targets.
It can be reproduce with:
# tc qd add dev eth1 ingress handle ffff:
# tc filter add dev eth1 parent ffff: u32 match u32 0 0 action xt \
-j ECN --ecn-tcp-remove
It could also crash kernel when using target CLUSTERIP or TPROXY.
By now there's no proper value for par.entryinfo in ipt_init_target,
but it can not be set with NULL. This patch is to void all these
panics by setting it with an ipt_entry obj with all members = 0.
Note that this issue has been there since the very beginning.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rxrpc_service_prealloc_one() doesn't set the socket pointer on any new call
it preallocates, but does add it to the rxrpc net namespace call list.
This, however, causes rxrpc_put_call() to oops when the call is discarded
when the socket is closed. rxrpc_put_call() needs the socket to be able to
reach the namespace so that it can use a lock held therein.
Fix this by setting a call's socket pointer immediately before discarding
it.
This can be triggered by unloading the kafs module, resulting in an oops
like the following:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: rxrpc_put_call+0x1e2/0x32d
PGD 0
P4D 0
Oops: 0000 [#1] SMP
Modules linked in: kafs(E-)
CPU: 3 PID: 3037 Comm: rmmod Tainted: G E 4.12.0-fscache+ #213
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
task: ffff8803fc92e2c0 task.stack: ffff8803fef74000
RIP: 0010:rxrpc_put_call+0x1e2/0x32d
RSP: 0018:ffff8803fef77e08 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff8803fab99ac0 RCX: 000000000000000f
RDX: ffffffff81c50a40 RSI: 000000000000000c RDI: ffff8803fc92ea88
RBP: ffff8803fef77e30 R08: ffff8803fc87b941 R09: ffffffff82946d20
R10: ffff8803fef77d10 R11: 00000000000076fc R12: 0000000000000005
R13: ffff8803fab99c20 R14: 0000000000000001 R15: ffffffff816c6aee
FS: 00007f915a059700(0000) GS:ffff88041fb80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000030 CR3: 00000003fef39000 CR4: 00000000001406e0
Call Trace:
rxrpc_discard_prealloc+0x325/0x341
rxrpc_listen+0xf9/0x146
kernel_listen+0xb/0xd
afs_close_socket+0x3e/0x173 [kafs]
afs_exit+0x1f/0x57 [kafs]
SyS_delete_module+0x10f/0x19a
do_syscall_64+0x8a/0x149
entry_SYSCALL64_slow_path+0x25/0x25
Fixes: 2baec2c3f8 ("rxrpc: Support network namespacing")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
list.dev has not been initialized and so the copy_to_user is copying
data from the stack back to user space which is a potential
information leak. Fix this ensuring all of list is initialized to
zero.
Detected by CoverityScan, CID#1357894 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some situations tcp_send_loss_probe() can realize that it's unable
to send a loss probe (TLP), and falls back to calling tcp_rearm_rto()
to schedule an RTO timer. In such cases, sometimes tcp_rearm_rto()
realizes that the RTO was eligible to fire immediately or at some
point in the past (delta_us <= 0). Previously in such cases
tcp_rearm_rto() was scheduling such "overdue" RTOs to happen at now +
icsk_rto, which caused needless delays of hundreds of milliseconds
(and non-linear behavior that made reproducible testing
difficult). This commit changes the logic to schedule "overdue" RTOs
ASAP, rather than at now + icsk_rto.
Fixes: 6ba8a3b19e ("tcp: Tail loss probe (TLP)")
Suggested-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzcaller reported the following use-after-free issue in rt6_select():
BUG: KASAN: use-after-free in rt6_select net/ipv6/route.c:755 [inline] at addr ffff8800bc6994e8
BUG: KASAN: use-after-free in ip6_pol_route.isra.46+0x1429/0x1470 net/ipv6/route.c:1084 at addr ffff8800bc6994e8
Read of size 4 by task syz-executor1/439628
CPU: 0 PID: 439628 Comm: syz-executor1 Not tainted 4.3.5+ #8
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
0000000000000000 ffff88018fe435b0 ffffffff81ca384d ffff8801d3588c00
ffff8800bc699380 ffff8800bc699500 dffffc0000000000 ffff8801d40a47c0
ffff88018fe435d8 ffffffff81735751 ffff88018fe43660 ffff8800bc699380
Call Trace:
[<ffffffff81ca384d>] __dump_stack lib/dump_stack.c:15 [inline]
[<ffffffff81ca384d>] dump_stack+0xc1/0x124 lib/dump_stack.c:51
sctp: [Deprecated]: syz-executor0 (pid 439615) Use of struct sctp_assoc_value in delayed_ack socket option.
Use struct sctp_sack_info instead
[<ffffffff81735751>] kasan_object_err+0x21/0x70 mm/kasan/report.c:158
[<ffffffff817359c4>] print_address_description mm/kasan/report.c:196 [inline]
[<ffffffff817359c4>] kasan_report_error+0x1b4/0x4a0 mm/kasan/report.c:285
[<ffffffff81735d93>] kasan_report mm/kasan/report.c:305 [inline]
[<ffffffff81735d93>] __asan_report_load4_noabort+0x43/0x50 mm/kasan/report.c:325
[<ffffffff82a28e39>] rt6_select net/ipv6/route.c:755 [inline]
[<ffffffff82a28e39>] ip6_pol_route.isra.46+0x1429/0x1470 net/ipv6/route.c:1084
[<ffffffff82a28fb1>] ip6_pol_route_output+0x81/0xb0 net/ipv6/route.c:1203
[<ffffffff82ab0a50>] fib6_rule_action+0x1f0/0x680 net/ipv6/fib6_rules.c:95
[<ffffffff8265cbb6>] fib_rules_lookup+0x2a6/0x7a0 net/core/fib_rules.c:223
[<ffffffff82ab1430>] fib6_rule_lookup+0xd0/0x250 net/ipv6/fib6_rules.c:41
[<ffffffff82a22006>] ip6_route_output+0x1d6/0x2c0 net/ipv6/route.c:1224
[<ffffffff829e83d2>] ip6_dst_lookup_tail+0x4d2/0x890 net/ipv6/ip6_output.c:943
[<ffffffff829e889a>] ip6_dst_lookup_flow+0x9a/0x250 net/ipv6/ip6_output.c:1079
[<ffffffff82a9f7d8>] ip6_datagram_dst_update+0x538/0xd40 net/ipv6/datagram.c:91
[<ffffffff82aa0978>] __ip6_datagram_connect net/ipv6/datagram.c:251 [inline]
[<ffffffff82aa0978>] ip6_datagram_connect+0x518/0xe50 net/ipv6/datagram.c:272
[<ffffffff82aa1313>] ip6_datagram_connect_v6_only+0x63/0x90 net/ipv6/datagram.c:284
[<ffffffff8292f790>] inet_dgram_connect+0x170/0x1f0 net/ipv4/af_inet.c:564
[<ffffffff82565547>] SYSC_connect+0x1a7/0x2f0 net/socket.c:1582
[<ffffffff8256a649>] SyS_connect+0x29/0x30 net/socket.c:1563
[<ffffffff82c72032>] entry_SYSCALL_64_fastpath+0x12/0x17
Object at ffff8800bc699380, in cache ip6_dst_cache size: 384
The root cause of it is that in fib6_add_rt2node(), when it replaces an
existing route with the new one, it does not update fn->rr_ptr.
This commit resets fn->rr_ptr to NULL when it points to a route which is
replaced in fib6_add_rt2node().
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syszkaller reported use-after-free in tipc [1]
When msg->rep skb is freed, set the pointer to NULL,
so that caller does not free it again.
[1]
==================================================================
BUG: KASAN: use-after-free in skb_push+0xd4/0xe0 net/core/skbuff.c:1466
Read of size 8 at addr ffff8801c6e71e90 by task syz-executor5/4115
CPU: 1 PID: 4115 Comm: syz-executor5 Not tainted 4.13.0-rc4+ #32
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
print_address_description+0x73/0x250 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x24e/0x340 mm/kasan/report.c:409
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:430
skb_push+0xd4/0xe0 net/core/skbuff.c:1466
tipc_nl_compat_recv+0x833/0x18f0 net/tipc/netlink_compat.c:1209
genl_family_rcv_msg+0x7b7/0xfb0 net/netlink/genetlink.c:598
genl_rcv_msg+0xb2/0x140 net/netlink/genetlink.c:623
netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2397
genl_rcv+0x28/0x40 net/netlink/genetlink.c:634
netlink_unicast_kernel net/netlink/af_netlink.c:1265 [inline]
netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1291
netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1854
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
sock_write_iter+0x31a/0x5d0 net/socket.c:898
call_write_iter include/linux/fs.h:1743 [inline]
new_sync_write fs/read_write.c:457 [inline]
__vfs_write+0x684/0x970 fs/read_write.c:470
vfs_write+0x189/0x510 fs/read_write.c:518
SYSC_write fs/read_write.c:565 [inline]
SyS_write+0xef/0x220 fs/read_write.c:557
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x4512e9
RSP: 002b:00007f3bc8184c08 EFLAGS: 00000216 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000718000 RCX: 00000000004512e9
RDX: 0000000000000020 RSI: 0000000020fdb000 RDI: 0000000000000006
RBP: 0000000000000086 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000216 R12: 00000000004b5e76
R13: 00007f3bc8184b48 R14: 00000000004b5e86 R15: 0000000000000000
Allocated by task 4115:
save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:551
kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:489
kmem_cache_alloc_node+0x13d/0x750 mm/slab.c:3651
__alloc_skb+0xf1/0x740 net/core/skbuff.c:219
alloc_skb include/linux/skbuff.h:903 [inline]
tipc_tlv_alloc+0x26/0xb0 net/tipc/netlink_compat.c:148
tipc_nl_compat_dumpit+0xf2/0x3c0 net/tipc/netlink_compat.c:248
tipc_nl_compat_handle net/tipc/netlink_compat.c:1130 [inline]
tipc_nl_compat_recv+0x756/0x18f0 net/tipc/netlink_compat.c:1199
genl_family_rcv_msg+0x7b7/0xfb0 net/netlink/genetlink.c:598
genl_rcv_msg+0xb2/0x140 net/netlink/genetlink.c:623
netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2397
genl_rcv+0x28/0x40 net/netlink/genetlink.c:634
netlink_unicast_kernel net/netlink/af_netlink.c:1265 [inline]
netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1291
netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1854
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
sock_write_iter+0x31a/0x5d0 net/socket.c:898
call_write_iter include/linux/fs.h:1743 [inline]
new_sync_write fs/read_write.c:457 [inline]
__vfs_write+0x684/0x970 fs/read_write.c:470
vfs_write+0x189/0x510 fs/read_write.c:518
SYSC_write fs/read_write.c:565 [inline]
SyS_write+0xef/0x220 fs/read_write.c:557
entry_SYSCALL_64_fastpath+0x1f/0xbe
Freed by task 4115:
save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_slab_free+0x71/0xc0 mm/kasan/kasan.c:524
__cache_free mm/slab.c:3503 [inline]
kmem_cache_free+0x77/0x280 mm/slab.c:3763
kfree_skbmem+0x1a1/0x1d0 net/core/skbuff.c:622
__kfree_skb net/core/skbuff.c:682 [inline]
kfree_skb+0x165/0x4c0 net/core/skbuff.c:699
tipc_nl_compat_dumpit+0x36a/0x3c0 net/tipc/netlink_compat.c:260
tipc_nl_compat_handle net/tipc/netlink_compat.c:1130 [inline]
tipc_nl_compat_recv+0x756/0x18f0 net/tipc/netlink_compat.c:1199
genl_family_rcv_msg+0x7b7/0xfb0 net/netlink/genetlink.c:598
genl_rcv_msg+0xb2/0x140 net/netlink/genetlink.c:623
netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2397
genl_rcv+0x28/0x40 net/netlink/genetlink.c:634
netlink_unicast_kernel net/netlink/af_netlink.c:1265 [inline]
netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1291
netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1854
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
sock_write_iter+0x31a/0x5d0 net/socket.c:898
call_write_iter include/linux/fs.h:1743 [inline]
new_sync_write fs/read_write.c:457 [inline]
__vfs_write+0x684/0x970 fs/read_write.c:470
vfs_write+0x189/0x510 fs/read_write.c:518
SYSC_write fs/read_write.c:565 [inline]
SyS_write+0xef/0x220 fs/read_write.c:557
entry_SYSCALL_64_fastpath+0x1f/0xbe
The buggy address belongs to the object at ffff8801c6e71dc0
which belongs to the cache skbuff_head_cache of size 224
The buggy address is located 208 bytes inside of
224-byte region [ffff8801c6e71dc0, ffff8801c6e71ea0)
The buggy address belongs to the page:
page:ffffea00071b9c40 count:1 mapcount:0 mapping:ffff8801c6e71000 index:0x0
flags: 0x200000000000100(slab)
raw: 0200000000000100 ffff8801c6e71000 0000000000000000 000000010000000c
raw: ffffea0007224a20 ffff8801d98caf48 ffff8801d9e79040 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801c6e71d80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff8801c6e71e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8801c6e71e80: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff8801c6e71f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8801c6e71f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to commit e6afc8ace6 ("udp: remove
headers from UDP packets before queueing"), when udp packets are being
peeked the requested extra offset is always 0 as there is no need to skip
the udp header. However, when the offset is 0 and the next skb is
of length 0, it is only returned once. The behaviour can be seen with
the following python script:
from socket import *;
f=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
g=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
f.bind(('::', 0));
addr=('::1', f.getsockname()[1]);
g.sendto(b'', addr)
g.sendto(b'b', addr)
print(f.recvfrom(10, MSG_PEEK));
print(f.recvfrom(10, MSG_PEEK));
Where the expected output should be the empty string twice.
Instead, make sk_peek_offset return negative values, and pass those values
to __skb_try_recv_datagram/__skb_try_recv_from_queue. If the passed offset
to __skb_try_recv_from_queue is negative, the checked skb is never skipped.
__skb_try_recv_from_queue will then ensure the offset is reset back to 0
if a peek is requested without an offset, unless no packets are found.
Also simplify the if condition in __skb_try_recv_from_queue. If _off is
greater then 0, and off is greater then or equal to skb->len, then
(_off || skb->len) must always be true assuming skb->len >= 0 is always
true.
Also remove a redundant check around a call to sk_peek_offset in af_unix.c,
as it double checked if MSG_PEEK was set in the flags.
V2:
- Moved the negative fixup into __skb_try_recv_from_queue, and remove now
redundant checks
- Fix peeking in udp{,v6}_recvmsg to report the right value when the
offset is 0
V3:
- Marked new branch in __skb_try_recv_from_queue as unlikely.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dereference before check is wrong and leads to an oops when
p_filter_chain is NULL. The check needs to be done on the pointer to
prevent NULL dereference.
Fixes: f93e1cdcf4 ("net/sched: fix filter flushing")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on yet another syzkaller report, I found
that our IP_MAX_MTU enforcements were not properly done.
gcc seems to reload dev->mtu for min(dev->mtu, IP_MAX_MTU), and
final result can be bigger than IP_MAX_MTU :/
This is a problem because device mtu can be changed on other cpus or
threads.
While this patch does not fix the issue I am working on, it is
probably worth addressing it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For sw_flow_actions, the actions_len only represents the kernel part's
size, and when we dump the actions to the userspace, we will do the
convertions, so it's true size may become bigger than the actions_len.
But unfortunately, for OVS_PACKET_ATTR_ACTIONS, we use the actions_len
to alloc the skbuff, so the user_skb's size may become insufficient and
oops will happen like this:
skbuff: skb_over_panic: text:ffffffff8148fabf len:1749 put:157 head:
ffff881300f39000 data:ffff881300f39000 tail:0x6d5 end:0x6c0 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:129!
[...]
Call Trace:
<IRQ>
[<ffffffff8148be82>] skb_put+0x43/0x44
[<ffffffff8148fabf>] skb_zerocopy+0x6c/0x1f4
[<ffffffffa0290d36>] queue_userspace_packet+0x3a3/0x448 [openvswitch]
[<ffffffffa0292023>] ovs_dp_upcall+0x30/0x5c [openvswitch]
[<ffffffffa028d435>] output_userspace+0x132/0x158 [openvswitch]
[<ffffffffa01e6890>] ? ip6_rcv_finish+0x74/0x77 [ipv6]
[<ffffffffa028e277>] do_execute_actions+0xcc1/0xdc8 [openvswitch]
[<ffffffffa028e3f2>] ovs_execute_actions+0x74/0x106 [openvswitch]
[<ffffffffa0292130>] ovs_dp_process_packet+0xe1/0xfd [openvswitch]
[<ffffffffa0292b77>] ? key_extract+0x63c/0x8d5 [openvswitch]
[<ffffffffa029848b>] ovs_vport_receive+0xa1/0xc3 [openvswitch]
[...]
Also we can find that the actions_len is much little than the orig_len:
crash> struct sw_flow_actions 0xffff8812f539d000
struct sw_flow_actions {
rcu = {
next = 0xffff8812f5398800,
func = 0xffffe3b00035db32
},
orig_len = 1384,
actions_len = 592,
actions = 0xffff8812f539d01c
}
So as a quick fix, use the orig_len instead of the actions_len to alloc
the user_skb.
Last, this oops happened on our system running a relative old kernel, but
the same risk still exists on the mainline, since we use the wrong
actions_len from the beginning.
Fixes: ccea74457b ("openvswitch: include datapath actions with sampled-packet upcall to userspace")
Cc: Neil McKee <neil.mckee@inmon.com>
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anuradha reported that statically added groups for interfaces enslaved
to a VRF device were not persisting. The problem is that igmp queries
and reports need to use the data in the in_dev for the real ingress
device rather than the VRF device. Update igmp_rcv accordingly.
Fixes: e58e415968 ("net: Enable support for VRF with ipv4 multicast")
Reported-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was added in commit e57a784d8c ("pkt_sched: set root qdisc
before change() in attach_default_qdiscs()") to hide duplicates
from "tc qdisc show" for incative deivices.
After 59cc1f61f ("net: sched: convert qdisc linked list to hashtable")
it triggered when classful qdisc is added to inactive device because
default qdiscs are added before switching root qdisc.
Anyway after commit ea32746953 ("net: sched: avoid duplicates in
qdisc dump") duplicates are filtered right in dumper.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sfq_enqueue() drops head packet or packet from another queue it
have to update backlog at upper qdiscs too.
Fixes: 2ccccf5fb4 ("net_sched: update hierarchical backlog too")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Traffic filters could keep direct pointers to classes in classful qdisc,
thus qdisc destruction first removes all filters before freeing classes.
Class destruction methods also tries to free attached filters but now
this isn't safe because tcf_block_put() unlike to tcf_destroy_chain()
cannot be called second time.
This patch set class->block to NULL after first tcf_block_put() and
turn second call into no-op.
Fixes: 6529eaba33 ("net: sched: introduce tcf block infractructure")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If fi->fib_metrics could not be allocated in fib_create_info()
we attempt to dereference a NULL pointer in free_fib_info_rcu() :
m = fi->fib_metrics;
if (m != &dst_default_metrics && atomic_dec_and_test(&m->refcnt))
kfree(m);
Before my recent patch, we used to call kfree(NULL) and nothing wrong
happened.
Instead of using RCU to defer freeing while we are under memory stress,
it seems better to take immediate action.
This was reported by syzkaller team.
Fixes: 3fb07daff8 ("ipv4: add reference counting to metrics")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time quite a few fixes for iwlwifi and one major regression fix
for brcmfmac. For the iwlwifi aggregation bug a small change was
needed for mac80211, but as Johannes is still away the mac80211 patch
is taken via wireless-drivers tree.
brcmfmac
* fix firmware crash (a recent regression in bcm4343{0,1,8}
iwlwifi
* Some simple PCI HW ID fix-ups and additions for family 9000
* Remove a bogus warning message with new FWs (bug #196915)
* Don't allow illegal channel options to be used (bug #195299)
* A fix for checksum offload in family 9000
* A fix serious throughput degradation in 11ac with multiple streams
* An old bug in SMPS where the firmware was not aware of SMPS changes
* Fix a memory leak in the SAR code
* Fix a stuck queue case in AP mode;
* Convert a WARN to a simple debug in a legitimate race case (from
which we can recover)
* Fix a severe throughput aggregation on 9000-family devices due to
aggregation issues, needed a small change in mac80211
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZkte/AAoJEG4XJFUm622bjqUH/01JNHIGh7WI2YHm9qA//uC0
L35j/nYwiBX47LREkVhgS2goR3BYihricM1w1uwv/1E/JJqECWVe7rPodoM4sYqh
jVVPy3ZYIK/Kk8i7v2W+VIeqR0b2q4PBt+UtruEBH1o8ESKZPDMqudq+AAbHeiih
tWJpPmS+IFW8yWaF9+v5DhWx5q4/JNvZgmNarS5/aPF+2bTR9Gw0bf8PUdyLip6J
rsv0W9e9SqmVBYkRoC4WMgM/RJbUh1d66SPQ3Yrv/nFL6cTgecC2IxQx7pCGUq9n
LbDJy6HCi+3mBJyMkVVs9iaXZiaNm7eUmEq16ENpiAnsQy5h9i/jVpySC0R/BzQ=
=KXB+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
This time quite a few fixes for iwlwifi and one major regression fix
for brcmfmac. For the iwlwifi aggregation bug a small change was
needed for mac80211, but as Johannes is still away the mac80211 patch
is taken via wireless-drivers tree.
brcmfmac
* fix firmware crash (a recent regression in bcm4343{0,1,8}
iwlwifi
* Some simple PCI HW ID fix-ups and additions for family 9000
* Remove a bogus warning message with new FWs (bug #196915)
* Don't allow illegal channel options to be used (bug #195299)
* A fix for checksum offload in family 9000
* A fix serious throughput degradation in 11ac with multiple streams
* An old bug in SMPS where the firmware was not aware of SMPS changes
* Fix a memory leak in the SAR code
* Fix a stuck queue case in AP mode;
* Convert a WARN to a simple debug in a legitimate race case (from
which we can recover)
* Fix a severe throughput aggregation on 9000-family devices due to
aggregation issues, needed a small change in mac80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Filtering the ACK packet was not put at the right place.
At this place, we already allocated a child and put it
into accept queue.
We absolutely need to call tcp_child_process() to release
its spinlock, or we will deadlock at accept() or close() time.
Found by syzkaller team (Thanks a lot !)
Fixes: 8fac365f63 ("tcp: Add a tcp_filter hook before handle ack packet")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dst is created by addrconf_dst_alloc() for a host route or an
anycast route, dst->dev points to loopback dev while rt6->rt6i_idev
points to a real device.
When the real device goes down, the current cleanup code only checks for
dst->dev and assumes rt6->rt6i_idev->dev is the same. This causes the
refcount leak on the real device in the above situation.
This patch makes sure to always release the refcount taken on
rt6->rt6i_idev during dst_dev_put().
Fixes: 587fea7411 ("ipv6: mark DST_NOGC and remove the operation of
dst_free()")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__tcp_ulp_find_autoload returns tcp_ulp_ops after taking a reference on
the module. Then, if ->init fails, tcp_set_ulp propagates the error but
nothing releases that reference.
Fixes: 734942cc4e ("tcp: ULP infrastructure")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function msg_reverse(), we reverse the header while trying to
reuse the original buffer whenever possible. Those rejected/returned
messages are always transmitted as unicast, but the msg_non_seq field
is not explicitly set to zero as it should be.
We have seen cases where multicast senders set the message type to
"NOT dest_droppable", meaning that a multicast message shorter than
one MTU will be returned, e.g., during receive buffer overflow, by
reusing the original buffer. This has the effect that even the
'msg_non_seq' field is inadvertently inherited by the rejected message,
although it is now sent as a unicast message. This again leads the
receiving unicast link endpoint to steer the packet toward the broadcast
link receive function, where it is dropped. The affected unicast link is
thereafter (after 100 failed retransmissions) declared 'stale' and
reset.
We fix this by unconditionally setting the 'msg_non_seq' flag to zero
for all rejected/returned messages.
Reported-by: Canh Duc Luu <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On L2 bearers, the TIPC broadcast function is sending out packets using
the corresponding L2 broadcast address. At reception, we filter such
packets under the assumption that they will also be delivered as
broadcast packets.
This assumption doesn't always hold true. Under high load, we have seen
that a switch may convert the destination address and deliver the packet
as a PACKET_MULTICAST, something leading to inadvertently dropped
packets and a stale and reset broadcast link.
We fix this by extending the reception filtering to accept packets of
type PACKET_MULTICAST.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ip route get $daddr iif eth0 from $saddr" causes:
BUG: KASAN: use-after-free in ip_route_input_rcu+0x1535/0x1b50
Call Trace:
ip_route_input_rcu+0x1535/0x1b50
ip_route_input_noref+0xf9/0x190
tcp_v4_early_demux+0x1a4/0x2b0
ip_rcv+0xbcb/0xc05
__netif_receive_skb+0x9c/0xd0
netif_receive_skb_internal+0x5a8/0x890
Problem is that inet_rtm_getroute calls either ip_route_input_rcu (if an
iif was provided) or ip_route_output_key_hash_rcu.
But ip_route_input_rcu, unlike ip_route_output_key_hash_rcu, already
associates the dst_entry with the skb. This clears the SKB_DST_NOREF
bit (i.e. skb_dst_drop will release/free the entry while it should not).
Thus only set the dst if we called ip_route_output_key_hash_rcu().
I tested this patch by running:
while true;do ip r get 10.0.1.2;done > /dev/null &
while true;do ip r get 10.0.1.2 iif eth0 from 10.0.1.1;done > /dev/null &
... and saw no crash or memory leak.
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: David Ahern <dsahern@gmail.com>
Fixes: ba52d61e0f ("ipv4: route: restore skb_dst_set in inet_rtm_getroute")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_SCHED or CONFIG_NET_RX_BUSY_POLL is /not/ set and
we try a narrow __sk_buff load of tc_index or napi_id, respectively,
then verifier rightfully complains that it's misconfigured, because
we need to set target_size in each of the two cases. The rewrite
for the ctx access is just a dummy op, but needs to pass, so fix
this up.
Fixes: f96da09473 ("bpf: simplify narrower ctx access")
Reported-by: Shubham Bansal <illusionist.neo@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this filters cannot be attached.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: 6529eaba33 ("net: sched: introduce tcf block infractructure")
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA layer frees the original skb when an xmit function returns NULL,
meaning an error occurred. But if the tagging code copied the original
skb, it is responsible of freeing the copy if an error occurs.
The ksz tagging code currently has two issues: if skb_put_padto fails,
the skb copy is not freed, and the original skb will be freed twice.
To fix that, move skb_put_padto inside both branches of the skb_tailroom
condition, before freeing the original skb, and free the copy on error.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates to tp_reserve can race with reads of the field in
packet_set_ring. Avoid this by holding the socket lock during
updates in setsockopt PACKET_RESERVE.
This bug was discovered by syzkaller.
Fixes: 8913336a7e ("packet: add PACKET_RESERVE sockopt")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When iteratively building a UDP datagram with MSG_MORE and that
datagram exceeds MTU, consistently choose UFO or fragmentation.
Once skb_is_gso, always apply ufo. Conversely, once a datagram is
split across multiple skbs, do not consider ufo.
Sendpage already maintains the first invariant, only add the second.
IPv6 does not have a sendpage implementation to modify.
A gso skb must have a partial checksum, do not follow sk_no_check_tx
in udp_send_skb.
Found by syzkaller.
Fixes: e89e9cf539 ("[IPv4/IPv6]: UFO Scatter-gather approach")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 55917a21d0 ("netfilter: x_tables: add context to know if
extension runs from nft_compat") introduced a member nft_compat to
xt_tgchk_param structure.
But it didn't set it's value for ipt_init_target. With unexpected
value in par.nft_compat, it may return unexpected result in some
target's checkentry.
This patch is to set all it's fields as 0 and only initialize the
non-zero fields in ipt_init_target.
v1->v2:
As Wang Cong's suggestion, fix it by setting all it's fields as
0 and only initializing the non-zero fields.
Fixes: 55917a21d0 ("netfilter: x_tables: add context to know if extension runs from nft_compat")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dcd87999d4 ("igmp: net: Move igmp namespace init to correct file")
moved the igmp sysctls initialization from tcp_sk_init to igmp_net_init. This
function is only called as part of per-namespace initialization, only if
CONFIG_IP_MULTICAST is defined, otherwise igmp_mc_init() call in ip_init is
compiled out, casuing the igmp pernet ops to not be registerd and those sysctl
being left initialized with 0. However, there are certain functions, such as
ip_mc_join_group which are always compiled and make use of some of those
sysctls. Let's do a partial revert of the aforementioned commit and move the
sysctl initialization into inet_init_net, that way they will always have
sane values.
Fixes: dcd87999d4 ("igmp: net: Move igmp namespace init to correct file")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196595
Reported-by: Gerardo Exequiel Pozzi <vmlinuz386@gmail.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link between two nodes come up, both endpoints will initially
send out a STATE message to the peer, to increase the probability that
the peer endpoint also is up when the first traffic message arrives.
Thereafter, if the establishing link is the second link between two
nodes, this first "traffic" message is a TUNNEL_PROTOCOL/SYNCH message,
helping the peer to perform initial synchronization between the two
links.
However, the initial STATE message may be lost, in which case the SYNCH
message will be the first one arriving at the peer. This should also
work, as the SYNCH message itself will be used to take up the link
endpoint before initializing synchronization.
Unfortunately the code for this case is broken. Currently, the link is
brought up through a tipc_link_fsm_evt(ESTABLISHED) when a SYNCH
arrives, whereupon __tipc_node_link_up() is called to distribute the
link slots and take the link into traffic. But, __tipc_node_link_up() is
itself starting with a test for whether the link is up, and if true,
returns without action. Clearly, the tipc_link_fsm_evt(ESTABLISHED) call
is unnecessary, since tipc_node_link_up() is itself issuing such an
event, but also harmful, since it inhibits tipc_node_link_up() to
perform the test of its tasks, and the link endpoint in question hence
is never taken into traffic.
This problem has been exposed when we set up dual links between pre-
and post-4.4 kernels, because the former ones don't send out the
initial STATE message described above.
We fix this by removing the unnecessary event call.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"The pull requests are getting smaller, that's progress I suppose :-)
1) Fix infinite loop in CIPSO option parsing, from Yujuan Qi.
2) Fix remote checksum handling in VXLAN and GUE tunneling drivers,
from Koichiro Den.
3) Missing u64_stats_init() calls in several drivers, from Florian
Fainelli.
4) TCP can set the congestion window to an invalid ssthresh value
after congestion window reductions, from Yuchung Cheng.
5) Fix BPF jit branch generation on s390, from Daniel Borkmann.
6) Correct MIPS ebpf JIT merge, from David Daney.
7) Correct byte order test in BPF test_verifier.c, from Daniel
Borkmann.
8) Fix various crashes and leaks in ASIX driver, from Dean Jenkins.
9) Handle SCTP checksums properly in mlx4 driver, from Davide
Caratti.
10) We can potentially enter tcp_connect() with a cached route
already, due to fastopen, so we have to explicitly invalidate it.
11) skb_warn_bad_offload() can bark in legitimate situations, fix from
Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
net: avoid skb_warn_bad_offload false positives on UFO
qmi_wwan: fix NULL deref on disconnect
ppp: fix xmit recursion detection on ppp channels
rds: Reintroduce statistics counting
tcp: fastopen: tcp_connect() must refresh the route
net: sched: set xt_tgchk_param par.net properly in ipt_init_target
net: dsa: mediatek: add adjust link support for user ports
net/mlx4_en: don't set CHECKSUM_COMPLETE on SCTP packets
qed: Fix a memory allocation failure test in 'qed_mcp_cmd_init()'
hysdn: fix to a race condition in put_log_buffer
s390/qeth: fix L3 next-hop in xmit qeth hdr
asix: Fix small memory leak in ax88772_unbind()
asix: Ensure asix_rx_fixup_info members are all reset
asix: Add rx->ax_skb = NULL after usbnet_skb_return()
bpf: fix selftest/bpf/test_pkt_md_access on s390x
netvsc: fix race on sub channel creation
bpf: fix byte order test in test_verifier
xgene: Always get clk source, but ignore if it's missing for SGMII ports
MIPS: Add missing file for eBPF JIT.
bpf, s390: fix build for libbpf and selftest suite
...
Some drivers handle rx buffer reordering internally (and by extension
handle also the rx ba session timer internally), but do not ofload the
addba/delba negotiation.
Add an api for these drivers to properly tear-down the ba session,
including sending a delba.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
skb_warn_bad_offload triggers a warning when an skb enters the GSO
stack at __skb_gso_segment that does not have CHECKSUM_PARTIAL
checksum offload set.
Commit b2504a5dbe ("net: reduce skb_warn_bad_offload() noise")
observed that SKB_GSO_DODGY producers can trigger the check and
that passing those packets through the GSO handlers will fix it
up. But, the software UFO handler will set ip_summed to
CHECKSUM_NONE.
When __skb_gso_segment is called from the receive path, this
triggers the warning again.
Make UFO set CHECKSUM_UNNECESSARY instead of CHECKSUM_NONE. On
Tx these two are equivalent. On Rx, this better matches the
skb state (checksum computed), as CHECKSUM_NONE here means no
checksum computed.
See also this thread for context:
http://patchwork.ozlabs.org/patch/799015/
Fixes: b2504a5dbe ("net: reduce skb_warn_bad_offload() noise")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 7e3f2952ee ("rds: don't let RDS shutdown a connection
while senders are present"), refilling the receive queue was removed
from rds_ib_recv(), along with the increment of
s_ib_rx_refill_from_thread.
Commit 73ce4317bf ("RDS: make sure we post recv buffers")
re-introduces filling the receive queue from rds_ib_recv(), but does
not add the statistics counter. rds_ib_recv() was later renamed to
rds_ib_recv_path().
This commit reintroduces the statistics counting of
s_ib_rx_refill_from_thread and s_ib_rx_refill_from_cq.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Reviewed-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With new TCP_FASTOPEN_CONNECT socket option, there is a possibility
to call tcp_connect() while socket sk_dst_cache is either NULL
or invalid.
+0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 4
+0 fcntl(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0
+0 setsockopt(4, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0
+0 connect(4, ..., ...) = 0
<< sk->sk_dst_cache becomes obsolete, or even set to NULL >>
+1 sendto(4, ..., 1000, MSG_FASTOPEN, ..., ...) = 1000
We need to refresh the route otherwise bad things can happen,
especially when syzkaller is running on the host :/
Fixes: 19f6d3f3c8 ("net/tcp-fastopen: Add new API support")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now xt_tgchk_param par in ipt_init_target is a local varibale,
par.net is not initialized there. Later when xt_check_target
calls target's checkentry in which it may access par.net, it
would cause kernel panic.
Jaroslav found this panic when running:
# ip link add TestIface type dummy
# tc qd add dev TestIface ingress handle ffff:
# tc filter add dev TestIface parent ffff: u32 match u32 0 0 \
action xt -j CONNMARK --set-mark 4
This patch is to pass net param into ipt_init_target and set
par.net with it properly in there.
v1->v2:
As Wang Cong pointed, I missed ipt_net_id != xt_net_id, so fix
it by also passing net_id to __tcf_ipt_init.
v2->v3:
Missed the fixes tag, so add it.
Fixes: ecb2421b5d ("netfilter: add and use nf_ct_netns_get/put")
Reported-by: Jaroslav Aster <jaster@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
->reencode_message() and last minute RADOS semantic changes in v12.1.2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJZhI6QAAoJEEp/3jgCEfOLeQYH/0b92RFzmsqwPI+U7iXdD06O
r0EXbT5dydMngJkWz/i3jBX8cMBvZyNhBh77VPDYXoFUp8//8uv5w73BkXe8JE08
+gLZU4oP/k7kl/YBYXgCcJYj7eIBFzqNvsWurKKHY/X3xrvEZ0HT+oub92xOUgRM
IBnZb1gZ4TJQT1MxqKOwb5aqcxaXlrOGfX7Di0aU3PFQXj5VnBI25NUQF1bgd9+A
MbhHpob6cbWZWzVdf0fTl28q9pStq4qggevRSM/5ZH/bETO8C80XYTuaPoLcQ0pY
VfpwgWIAPwotw9KU7W+ane13BURw76+pWMHaUZgiJKRyuRMBOT/gaER+AUeuR1o=
=XH7K
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.13-rc4' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A bunch of fixes and follow-ups for -rc1 Luminous patches: issues with
->reencode_message() and last minute RADOS semantic changes in
v12.1.2"
* tag 'ceph-for-4.13-rc4' of git://github.com/ceph/ceph-client:
libceph: make RECOVERY_DELETES feature create a new interval
libceph: upmap semantic changes
crush: assume weight_set != null imples weight_set_size > 0
libceph: fallback for when there isn't a pool-specific choose_arg
libceph: don't call ->reencode_message() more than once per message
libceph: make encode_request_*() work with r_mempool requests
Fix a TCP loss recovery performance bug raised recently on the netdev
list, in two threads:
(i) July 26, 2017: netdev thread "TCP fast retransmit issues"
(ii) July 26, 2017: netdev thread:
"[PATCH V2 net-next] TLP: Don't reschedule PTO when there's one
outstanding TLP retransmission"
The basic problem is that incoming TCP packets that did not indicate
forward progress could cause the xmit timer (TLP or RTO) to be rearmed
and pushed back in time. In certain corner cases this could result in
the following problems noted in these threads:
- Repeated ACKs coming in with bogus SACKs corrupted by middleboxes
could cause TCP to repeatedly schedule TLPs forever. We kept
sending TLPs after every ~200ms, which elicited bogus SACKs, which
caused more TLPs, ad infinitum; we never fired an RTO to fill in
the holes.
- Incoming data segments could, in some cases, cause us to reschedule
our RTO or TLP timer further out in time, for no good reason. This
could cause repeated inbound data to result in stalls in outbound
data, in the presence of packet loss.
This commit fixes these bugs by changing the TLP and RTO ACK
processing to:
(a) Only reschedule the xmit timer once per ACK.
(b) Only reschedule the xmit timer if tcp_clean_rtx_queue() deems the
ACK indicates sufficient forward progress (a packet was
cumulatively ACKed, or we got a SACK for a packet that was sent
before the most recent retransmit of the write queue head).
This brings us back into closer compliance with the RFCs, since, as
the comment for tcp_rearm_rto() notes, we should only restart the RTO
timer after forward progress on the connection. Previously we were
restarting the xmit timer even in these cases where there was no
forward progress.
As a side benefit, this commit simplifies and speeds up the TCP timer
arming logic. We had been calling inet_csk_reset_xmit_timer() three
times on normal ACKs that cumulatively acknowledged some data:
1) Once near the top of tcp_ack() to switch from TLP timer to RTO:
if (icsk->icsk_pending == ICSK_TIME_LOSS_PROBE)
tcp_rearm_rto(sk);
2) Once in tcp_clean_rtx_queue(), to update the RTO:
if (flag & FLAG_ACKED) {
tcp_rearm_rto(sk);
3) Once in tcp_ack() after tcp_fastretrans_alert() to switch from RTO
to TLP:
if (icsk->icsk_pending == ICSK_TIME_RETRANS)
tcp_schedule_loss_probe(sk);
This commit, by only rescheduling the xmit timer once per ACK,
simplifies the code and reduces CPU overhead.
This commit was tested in an A/B test with Google web server
traffic. SNMP stats and request latency metrics were within noise
levels, substantiating that for normal web traffic patterns this is a
rare issue. This commit was also tested with packetdrill tests to
verify that it fixes the timer behavior in the corner cases discussed
in the netdev threads mentioned above.
This patch is a bug fix patch intended to be queued for -stable
relases.
Fixes: 6ba8a3b19e ("tcp: Tail loss probe (TLP)")
Reported-by: Klavs Klavsen <kl@vsen.dk>
Reported-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have tcp_schedule_loss_probe() base the TLP scheduling decision based
on when the RTO *should* fire. This is to enable the upcoming xmit
timer fix in this series, where tcp_schedule_loss_probe() cannot
assume that the last timer installed was an RTO timer (because we are
no longer doing the "rearm RTO, rearm RTO, rearm TLP" dance on every
ACK). So tcp_schedule_loss_probe() must independently figure out when
an RTO would want to fire.
In the new TLP implementation following in this series, we cannot
assume that icsk_timeout was set based on an RTO; after processing a
cumulative ACK the icsk_timeout we see can be from a previous TLP or
RTO. So we need to independently recalculate the RTO time (instead of
reading it out of icsk_timeout). Removing this dependency on the
nature of icsk_timeout makes things a little easier to reason about
anyway.
Note that the old and new code should be equivalent, since they are
both saying: "if the RTO is in the future, but at an earlier time than
the normal TLP time, then set the TLP timer to fire when the RTO would
have fired".
Fixes: 6ba8a3b19e ("tcp: Tail loss probe (TLP)")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pure refactor. This helper will be required in the xmit timer fix
later in the patch series. (Because the TLP logic will want to make
this calculation.)
Fixes: 6ba8a3b19e ("tcp: Tail loss probe (TLP)")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c2ed1880fd ("net: ipv6: check route protocol when
deleting routes"), ipv6 route checks rt protocol when trying to
remove a rt entry.
It introduced a side effect causing 'ip -6 route flush cache' not
to work well. When flushing caches with iproute, all route caches
get dumped from kernel then removed one by one by sending DELROUTE
requests to kernel for each cache.
The thing is iproute sends the request with the cache whose proto
is set with RTPROT_REDIRECT by rt6_fill_node() when kernel dumps
it. But in kernel the rt_cache protocol is still 0, which causes
the cache not to be matched and removed.
So the real reason is rt6i_protocol in the route is not set when
it is allocated. As David Ahern's suggestion, this patch is to
set rt6i_protocol properly in the route when it is installed and
remove the codes setting rtm_protocol according to rt6i_flags in
rt6_fill_node.
This is also an improvement to keep rt6i_protocol consistent with
rtm_protocol.
Fixes: c2ed1880fd ("net: ipv6: check route protocol when deleting routes")
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds