Remove harmful BUG_ON() from ata_bmdma_qc_issue(),
as it casts too wide of a net and breaks sata_mv.
It also crashes the kernel while doing the BUG_ON().
There's already a WARN_ON_ONCE() further down to catch
the case of POLLING for a BMDMA operation.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
Fix DSM/TRIM commands in sata_mv (v2).
These need to be issued using old-school "BM DMA",
rather than via the EDMA host queue.
Since the chips don't have proper BM DMA status,
we need to be more careful with setting the ATA_DMA_INTR bit,
since DSM/TRIM often has a long delay between "DMA complete"
and "command complete".
GEN_I chips don't have BM DMA, so no TRIM for them.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
ata_qc_issue() BUG_ON()s on data commands w/o data, which may be
submitted via SG_IO. Be less of a drama queen and just trigger
WARN_ON_ONCE() and fail the command with AC_ERR_SYSTEM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stefan Hübner <stefan.huebner@stud.tu-ilmenau.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dma_dwc_xfer_setup() returns an int and "dma_chan" needs to be signed
for the error handling to work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
88SE9128 can do FBS and sets it in HOST_CAP but forgets to set FBSCP
in PORT_CMD. Implement AHCI_HFLAG_YES_FBS and apply it to 88SE9128.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Winbond W83759A controller is fully supported by pata_legacy driver
so remove no longer needed pata_winbond driver.
Leave PATA_WINBOND_VLB config option for compatibility reasons
and teach pata_legacy to preserve the old behavior of pata_winbond
driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit d62f5576 (pata_cmd64x: fix handling of address setup timings)
incorrectly called ata_timing_compute() on UDMA mode on 0 @UT leading
to devide by zero fault. Revert it until better fix is available.
This is reported in bko#16607 by Milan Kocian who also root caused it.
https://bugzilla.kernel.org/show_bug.cgi?id=16607
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-root-caused-by: Milan Kocian <milan.kocian@wq.cz>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Just scrubbing some warnings so I can see real problem ones in the build
noise. For 32bit we need to coax gcc politely into believing we really
honestly intend to the casts. Using (u64)(unsigned long) means we cast from
a pointer to a type of the right size and then extend it. This stops the
warning spew.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sage Weil <sage@newdream.net>
ceph_get_inode() returns an ERR_PTR and it doesn't return a NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86, Pentium4: Clear the P4_CCCR_FORCE_OVF flag
tracing/trace_stack: Fix stack trace on ppc64
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
Eliminate sparse warning - bad constant expression
cifs: check for NULL session password
missing changes during ntlmv2/ntlmssp auth and sign
[CIFS] Fix ntlmv2 auth with ntlmssp
cifs: correction of unicode header files
cifs: fix NULL pointer dereference in cifs_find_smb_ses
cifs: consolidate error handling in several functions
cifs: clean up error handling in cifs_mknod
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, tsc, sched: Recompute cyc2ns_offset's during resume from sleep states
sched: Fix rq->clock synchronization when migrating tasks
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: handle events as edge-triggered
xen: use percpu interrupts for IPIs and VIRQs
* '2.6.36-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/xfsdev:
xfs: do not discard page cache data on EAGAIN
xfs: don't do memory allocation under the CIL context lock
xfs: Reduce log force overhead for delayed logging
xfs: dummy transactions should not dirty VFS state
xfs: ensure f_ffree returned by statfs() is non-negative
xfs: handle negative wbc->nr_to_write during sync writeback
writeback: write_cache_pages doesn't terminate at nr_to_write <= 0
xfs: fix untrusted inode number lookup
xfs: ensure we mark all inodes in a freed cluster XFS_ISTALE
xfs: unlock items before allowing the CIL to commit
No need to call input_free_device() after input_unregister_device().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Huaxu and Rudolf want me to be the hwmon coretemp driver maintainer and
remove their names from the coretemp maintainer entry.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit 8bf0223ed515be24de0c671eedaff49e78bebc9c (hwmon, k8temp: Fix
temperature reporting for ASB1 processor revisions) fixed temperature
reporting for ASB1 CPUs. But those CPU models (model 0x6b, 0x6f, 0x7f)
were packaged both as AM2 (desktop) and ASB1 (mobile). Thus the commit
leads to wrong temperature reporting for AM2 CPU parts.
The solution is to determine the package type for models 0x6b, 0x6f,
0x7f.
This is done using BrandId from CPUID Fn8000_0001_EBX[15:0]. See
"Constructing the processor Name String" in "Revision Guide for AMD
NPT Family 0Fh Processors" (Rev. 3.46).
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: stable@kernel.org [.32.x, .33.x, .34.x, .35.x]
Reported-by: Vladislav Guberinic <neosisani@gmail.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix the following build warning:
CC [M] drivers/hwmon/coretemp.o
drivers/hwmon/coretemp.c: In function "coretemp_init":
drivers/hwmon/coretemp.c:521: warning: unused variable "n"
drivers/hwmon/coretemp.c:521: warning: unused variable "p"
Introduced by commit 851b29cb3b. When
you drop code, you also have to drop the variables this code was
using.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
If on Pentium4 CPUs the FORCE_OVF flag is set then an NMI happens
on every event, which can generate a flood of NMIs. Clear it.
Reported-by: Vince Weaver <vweaver1@eecs.utk.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As reported by Anton Blanchard when we use
percpu_counter_read_positive() to make our orphan socket limit checks,
the check can be off by up to num_cpus_online() * batch (which is 32
by default) which on a 128 cpu machine can be as large as the default
orphan limit itself.
Fix this by doing the full expensive sum check if the optimized check
triggers.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
We used to use i_head_snapc to keep track of which snapc the current epoch
of dirty data was dirtied under. It is used by queue_cap_snap to set up
the cap_snap. However, since we queue cap snaps for any dirty caps, not
just for dirty file data, we need to keep a valid i_head_snapc anytime
we have dirty|flushing caps. This fixes a NULL pointer deref in
queue_cap_snap when writing back dirty caps without data (e.g.,
snaptest-authwb.sh).
Signed-off-by: Sage Weil <sage@newdream.net>
Casting "pep->tx_desc_dma" to to a struct tx_desc pointer makes gcc
complain:
drivers/net/pxa168_eth.c:657: warning:
cast to pointer from integer of different size
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mii_ioctl() function changed recently. It now takes a struct
ifreq pointer directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple issues here:
* Some resources weren't released.
* If alloc_etherdev() failed it would have caused a NULL dereference
because "pep" would be null when we checked "if (pep->clk)".
* Also it's better to propagate the error codes from mdiobus_register()
instead of just returning -ENOMEM.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"pep->pd" isn't checked consistently in this function. For example it's
dereferenced unconditionally on the next line after the end of the if
condition. This function is only called from pxa168_eth_probe() and
pep->pd is always non-NULL so I removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that phylib will call adjust_link before returning
from {,of_}phy_connect(), which may cause the following [very rare,
though] oops upon reopening the device:
Unable to handle kernel paging request for data at address 0x0000024c
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0
P1021 RDB
Modules linked in:
NIP: c0345dac LR: c0345dac CTR: c0345d84
TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0
[...]
NIP [c0345dac] adjust_link+0x28/0x19c
LR [c0345dac] adjust_link+0x28/0x19c
Call Trace:
[c0d25f00] [000045e1] 0x45e1 (unreliable)
[c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554
[...]
Here is why. Drivers store phydev in their private structures, e.g.
gianfar driver:
static int init_phy(struct net_device *dev)
{
...
priv->phydev = of_phy_connect(...);
...
}
So that adjust_link could retrieve it back:
static void adjust_link(struct net_device *dev)
{
...
struct phy_device *phydev = priv->phydev;
...
}
If the device has been opened before, then phydev->state is set to
PHY_HALTED (or undefined if the driver didn't call phy_stop()).
Now, phy_connect starts the PHY state machine before returning phydev to
the driver:
phy_start_machine(phydev, NULL);
if (phydev->irq > 0)
phy_start_interrupts(phydev);
return phydev;
The time between 'phy_start_machine()' and 'return phydev' is undefined.
The start machine routine delays execution for 1 second, which is enough
for most cases. But under heavy load, or if you're unlucky, it is quite
possible that PHY state machine will execute before phy_connect()
returns, and so adjust_link callback will try to dereference phydev,
which is not yet ready.
To fix the issue, simply initialize the PHY's state to PHY_READY during
phy_attach(). This will ensure that phylib won't call adjust_link before
phy_start().
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this error on an s390 allyesconfig build:
linux-2.6/drivers/net/caif/caif_spi.c:98:
undefined reference to `dma_free_coherent'
Cc: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pa-risc and ia64 have stacks that grow upwards. Check that
they do not run into other mappings. By making VM_GROWSUP
0x0 on architectures that do not ever use it, we can avoid
some unpleasant #ifdefs in check_stack_guard_page().
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When converting this to the new wait_for macro I inverted the wait
condition, which causes all sorts of problems. So correct it to fix
several failures caused by the bad wait (flickering, bad output
detection, tearing, etc.).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparse spotted that the kzalloc() in pm_qos_power_open() in the
current Linus' git tree had its parameters swapped. Fix this.
Signed-off-by: David Alan Gilbert <linux@treblig.org>
Acked-by: mark gross <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Xen events are logically edge triggered, as Xen only calls the event
upcall when an event is newly set, but not continuously as it remains set.
As a result, use handle_edge_irq rather than handle_level_irq.
This has the important side-effect of fixing a long-standing bug of
events getting lost if:
- an event's interrupt handler is running
- the event is migrated to a different vcpu
- the event is re-triggered
The most noticable symptom of these lost events is occasional lockups
of blkfront.
Many thanks to Tom Kopec and Daniel Stodden in tracking this down.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Tom Kopec <tek@acm.org>
Cc: Daniel Stodden <daniel.stodden@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
IPIs and VIRQs are inherently per-cpu event types, so treat them as such:
- use a specific percpu irq_chip implementation, and
- handle them with handle_percpu_irq
This makes the path for delivering these interrupts more efficient
(no masking/unmasking, no locks), and it avoid problems with attempts
to migrate them.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Eliminiate sparse warning during usage of crypto_shash_* APIs
error: bad constant expression
Allocate memory for shash descriptors once, so that we do not kmalloc/kfree it
for every signature generation (shash descriptor for md5 hash).
From ed7538619817777decc44b5660b52268077b74f3 Mon Sep 17 00:00:00 2001
From: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Date: Tue, 24 Aug 2010 11:47:43 -0500
Subject: [PATCH] eliminate sparse warnings during crypto_shash_* APis usage
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
We should pass the data to the data register.
Signed-off-by: Jianwei Yang <jianwei.yang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It looks like there is an off-by-one error in one of your changes to
drivers/staging/rar_register/rar_register.c:
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This build bug triggers:
drivers/built-in.o: In function `mantis_exit':
(.text+0x377413): undefined reference to `ir_input_unregister'
drivers/built-in.o: In function `mantis_input_init':
(.text+0x3774ff): undefined reference to `__ir_input_register'
If MANTIS_CORE is enabled but IR_CORE is not. Add the correct
dependency.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Get rid of indirect p1275 PROM call buffer.
sparc64: Fill a missing delay slot.
sparc64: Make lock backoff really a NOP on UP builds.
sparc64: simple microoptimizations for atomic functions
sparc64: Make rwsems 64-bit.
sparc64: Really fix atomic64_t interface types.
