[ Upstream commit 63fbf8013b ]
There need to enable pclk_gpio when do irq_create_mapping, since it will
do access to gpio controller.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20201013063731.3618-3-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7faa8ffb6 ]
In function rockchip_dt_node_to_map, a new_map variable is
allocated by:
new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map),
GFP_KERNEL);
This uses devres and attaches new_map to the pinctrl driver.
This cause a leak since new_map is not released when the probed
driver is removed. Fix it by using kcalloc to allocate new_map
and free it in `rockchip_dt_free_map`
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200506100903.15420-1-dafna.hirschfeld@collabora.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
When fall-through warnings was enabled by default the following warning
was starting to show up:
../drivers/pinctrl/pinctrl-rockchip.c: In function ‘rockchip_gpio_set_config’:
../drivers/pinctrl/pinctrl-rockchip.c:2783:3: warning: this statement may fall
through [-Wimplicit-fallthrough=]
rockchip_gpio_set_debounce(gc, offset, true);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/pinctrl/pinctrl-rockchip.c:2795:2: note: here
default:
^~~~~~~
Rework so that the compiler doesn't warn about fall-through. Add
'return -ENOTSUPP;' to match the comment.
Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20190726112812.19665-1-anders.roxell@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-rockchip.c:3221:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-rockchip.c:3223:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rk3188 has pins that are not handled through the regular iomuxing
for handling either nand-flash or an emmc and are set through only one
specifal setting. So utilize the routing function to simply do that
setting depending on one of the core nand/emmc signals that are actually
regular pins handled through pinctrl.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Right now we expect the pin-rounting settings to be in the same area
as the iomux setting itself. And while that seems to be true for all
newer Rockchip socs, back in the wild west days of old this wasn't true.
Nowadays pin settings in the GRF normally stay in the GRF and the same
is true for pins configured from PMU registers. But old socs like the
rk3188 really sprinkle pin settings somewhat randomly through both
for its bank0.
Therefore add the option to specify a location for the route setting,
so that we can map older socs correctly. We'll keep "same" as the
default, so that we only need to specify a location in the corner-cases
described above.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.
Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.
Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Could only support PIN_CONFIG_INPUT_DEBOUNCE now as the HW block
is too simple to support others. But even wrt. debounce capability,
it now could only support very limited period of time to satisfy the
real usecase. But still be useful to enable the crippled HW debounce
to prevent any spurious glitches from waking up the system if the
gpio is conguired as wakeup interrupt source.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 4 banks (GPIO0 ~ GPIO3), bank0 is in PD_PMU
subsystem, bank1/bank2/bank3 are in PD_BUS subsystem.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adjust words in these descriptions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit extra messages for a memory allocation failure in these functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We generally leave the GPIO clock disabled, unless an interrupt is
requested or we're accessing IO registers. We forgot to do this for the
->get_direction() callback, which means we can sometimes [1] get
incorrect results [2] from, e.g., /sys/kernel/debug/gpio.
Enable the clock, so we get the right results!
[1] Sometimes, because many systems have 1 or mor interrupt requested on
each GPIO bank, so they always leave their clock on.
[2] Incorrect, meaning the register returns 0, and so we interpret that
as "input".
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rk3288 also has one function that can be routed to one of two pins,
the hdmi cec functionality can use either gpio7c0 or gpio7c7.
So add the route switching support for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the gmac-m1 optimization(bit10) is selected, the gpio function
of gmac pins is not valid. We may use the rmii mode for gmac interface,
the pins such as rx_d2, rx_d3, which the rgmii mode used, but rmii not
used could be taken as gpio function. So gmac_rxd0m1 selects the bit2,
and gmac_rxd0m3 select bit10 is more correct.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The offset of gpio0 and gpio1 bank drive strength is 0x8, not 0x4.
But the mux is 0x4, we couldn't use the IOMUX_WIDTH_4BIT flag, so
we give them actual offset.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pins from GPIO1A0 to GPIO1B1 are special, need to recalculate
iomux. And the register offset is larger than the u8 range, so changed
to u32.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pins like i2c SCL/SDA need the schmitt input function
to avoid crosstalk problems.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 3 IP blocks pin routes need to be switched, that are
emmc-cmd, spi, i2s. And there are some pins need to be recalced,
which are gpio2c4~gpio2c7 and gpio2d0.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The other Socs also need the feature of recalced iomux, so
make it as a common interface like iomux route feature.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output
buffers without actually enabling input and/or output on a
pin. We are chiseling out some details of pin control
electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the
tree to use this pin controller and consolidate earlier
spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control.
All users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for
RK3228, RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register
access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes.
-----BEGIN PGP SIGNATURE-----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=dUFL
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
There are 2 IP blocks pin routes need to be switched, that are
uart2dbg, pcie_clkreq.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 8 IP blocks pin routes need to be switched, that are
uart2dbg, gmac-m1-optimized, pdm, spi, i2s2, card, tsp, cif.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 9 IP blocks pin routes need to be switched, that are
pwm-0, pwm-1, pwm-2, pwm-3, sdio, spi, emmc, uart2, uart1.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the some rockchip SOCS, some things like rk3399 specific uart2 can use
multiple pins. Somewhere between the pin io-cells and the uart it seems
to have some sort of switch to decide to which pin to actually route the
data.
+-------+ +--------+ /- GPIO4_B0 (pinmux 2)
| uart2 | -- | switch | --- GPIO4_C0 (pinmux 2)
+-------+ +--------+ \- GPIO4_C3 (pinmux 2)
(switch selects one of the 3 pins base on the GRF_SOC_CON7[BIT0, BIT1])
The routing switch is determined by one pin of a specific group to be set
to its special pinmux function. If the pinmux setting is wrong for that
pin the ip block won't work correctly anyway.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With real-time preemption, regmap functions cannot be used in the
implementation of irq_chip since they use spinlocks which may sleep.
Move the setting of the mux for IRQs to an irq_bus_sync_unlock handler
where we are allowed to sleep.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to avoid calling regmap functions from irq handlers, so the next
commit is going to move the call to rockchip_set_mux() into an
irq_bus_sync_unlock handler. But we can't return an error from there so
we still need to check the settings from rockchip_irq_set_type() and we
will use this new rockchip_verify_mux() function from there.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This lock is used from rockchip_irq_set_type() which is part of the
irq_chip implementation and thus must use raw_spinlock_t as documented
in Documentation/gpio/driver.txt.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
regmap_update_bits does its own locking and everything else accessed
here is a local variable so there is no need to lock around it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[adapted rk1108 dtsi to keep bisectability]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we are trying to enable/disable the clk of irq's gpio bank when
unmask/mask irq. But the kernel's "lazy disable approach" will skip masking
irq when the irq chip doesn't support irq_disable ops.
So we may hit this case:
irq_enable-> enable clk
irq_disable-> noop
irq_enable-> enable clk again
irq_disable-> noop
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To prevent external signal crosstalk, some pins need to
enable input schmitt, like i2c pins, 32k-input pin and so on.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Note, the iomux of following pins are special, need to
be recalculated specially.
- gpio2_b4
- gpio2_b7
- gpio2_c7
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pins are special at a bank so that add
IOMUX_RECALCED type to indicate which iomux source
of the bank need to be recalculated. If the mux
recalculateed callback and IOMUX_RECALCED type
were set, recalculate the pins' iomux by using
mux recalculated data struct.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.
In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.
We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This add pinctrl support for Rockchip RK1108 Soc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Series-changes: 2
- add pull and drive-strength functionality
Series-changes: 3
- two minor CodingStyle fixes adviced by Heiko
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_ROCKCHIP
drivers/pinctrl/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rockchip_irq_gc_mask_set_bit() function is not exported our used
outside of ppinctrl-rockchip.c so fix the following sparse error by
making it static:
drivers/pinctrl/pinctrl-rockchip.c:2010:6: warning:
symbol 'rockchip_irq_gc_mask_set_bit' was not declared.
Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When building with 'make W=1', we get harmless warnings about
five drivers in drivers/pinctrl, which all contain a copy of
the same line:
drivers/pinctrl/freescale/pinctrl-imx1-core.c:160:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
This replaces the somewhat nonstandard 'static const inline'
with 'static inline const', which has the same meaning but
does not cause this warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the pinctrl pull bias setting, since the pull up/down
setting is the contrary for gpio0(just the gpio0a and gpio0b) and
gpio2(just the gpio2c and gpio2d).
From the TRM said, the gpio0a pull polarity setting:
gpio0a_p
GPIO0A PE/PS programmation section, every
GPIO bit corresponding to 2bits[PS:PE]
2'b00: Z(Normal operation);
2'b11: weak 1(pull-up);
2'b01: weak 0(pull-down);
2'b10: Z(Normal operation);
Then, the other gpios setting as the following:
gpio1a_p (e.g.: gpio1, gpio2a, gpio2b, gpio3...)
GPIO1A PU/PD programmation section, every
GPIO bit corresponding to 2bits
2'b00: Z(Normal operation);
2'b01: weak 1(pull-up);
2'b10: weak 0(pull-down);
2'b11: Z(Normal operation);
For example,(rk3399evb board)
sdmmc_cd --->gpio0_a7
localhost / # io -r -4 0xff320040
ff320040: 00004d5f
In general,the value should be 0x0000cd5f since the pin has been set
in the dts.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: linux-gpio@vger.kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the get_direction to support the gpio
interface.
The gpio direction is not used on rockchip platform when use the gpio
debugfs.
Tested on kylin board. (RK3036 SoCs)
The repro steps:
$/sys/class/gpio/
echo 53 > export
$/sys/class/gpio/gpio53# cat direction
in
In general, the gpio53 should be out value, but the direction is the
default value 'in', since the get_direction didn't supported in rockchip
pinctrl.
So, we should add this patch to support it.
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Reported-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jianqun Xu