The netvsc VF skb handler should make sure that skb is not
shared. Similar logic already exists in bonding and team device
drivers.
This is not an issue in practice because the VF devicex
does not send up shared skb's. But the netvsc driver
should do the right thing if it did.
Fixes: 0c195567a8 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when resegmenting an unexpected UDP GRO packet, the full UDP
checksum will be calculated for every new SKB created by skb_segment()
because the netdev features passed in by udp_rcv_segment() lack any
information about checksum offload capabilities.
Usually, we have no need to perform this calculation again, as
1) The GRO implementation guarantees that any packets making it to the
udp_rcv_segment() function had correct checksums, and, more
importantly,
2) Upon the successful return of udp_rcv_segment(), we immediately pull
the UDP header off and either queue the segment to the socket or
hand it off to a new protocol handler.
Unless userspace has set the IP_CHECKSUM sockopt to indicate that they
want the final checksum values, we can pass the needed netdev feature
flags to __skb_gso_segment() to avoid checksumming each segment in
skb_segment().
Fixes: cf329aa42b ("udp: cope with UDP GRO packet misdirection")
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sprgs are a set of 4 general purpose sprs provided for software use.
SPRG3 is special in that it can also be read from userspace. Thus it is
used on linux to store the cpu and numa id of the process to speed up
syscall access to this information.
This register is overwritten with the guest value on kvm guest entry,
and so needs to be restored on exit again. Thus restore the value on
the guest exit path in kvmhv_p9_guest_entry().
Cc: stable@vger.kernel.org # v4.20+
Fixes: 95a6432ce9 ("KVM: PPC: Book3S HV: Streamlined guest entry/exit path on P9 for radix guests")
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Under XIVE, the ESB pages of an interrupt are used for interrupt
management (EOI) and triggering. They are made available to guests
through a mapping of the XIVE KVM device.
When a device is passed-through, the passthru_irq helpers,
kvmppc_xive_set_mapped() and kvmppc_xive_clr_mapped(), clear the ESB
pages of the guest IRQ number being mapped and let the VM fault
handler repopulate with the correct page.
The ESB pages are mapped at offset 4 (KVM_XIVE_ESB_PAGE_OFFSET) in the
KVM device mapping. Unfortunately, this offset was not taken into
account when clearing the pages. This lead to issues with the
passthrough devices for which the interrupts were not functional under
some guest configuration (tg3 and single CPU) or in any configuration
(e1000e adapter).
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
According to Documentation/virtual/kvm/locking.txt, the srcu read lock
should be taken when accessing the memslots of the VM. The XIVE KVM
device needs to do so when configuring the page of the OS event queue
of vCPU for a given priority and when marking the same page dirty
before migration.
This avoids warnings such as :
[ 208.224882] =============================
[ 208.224884] WARNING: suspicious RCU usage
[ 208.224889] 5.2.0-rc2-xive+ #47 Not tainted
[ 208.224890] -----------------------------
[ 208.224894] ../include/linux/kvm_host.h:633 suspicious rcu_dereference_check() usage!
[ 208.224896]
other info that might help us debug this:
[ 208.224898]
rcu_scheduler_active = 2, debug_locks = 1
[ 208.224901] no locks held by qemu-system-ppc/3923.
[ 208.224902]
stack backtrace:
[ 208.224907] CPU: 64 PID: 3923 Comm: qemu-system-ppc Kdump: loaded Not tainted 5.2.0-rc2-xive+ #47
[ 208.224909] Call Trace:
[ 208.224918] [c000200cdd98fa30] [c000000000be1934] dump_stack+0xe8/0x164 (unreliable)
[ 208.224924] [c000200cdd98fa80] [c0000000001aec80] lockdep_rcu_suspicious+0x110/0x180
[ 208.224935] [c000200cdd98fb00] [c0080000075933a0] gfn_to_memslot+0x1c8/0x200 [kvm]
[ 208.224943] [c000200cdd98fb40] [c008000007599600] gfn_to_pfn+0x28/0x60 [kvm]
[ 208.224951] [c000200cdd98fb70] [c008000007599658] gfn_to_page+0x20/0x40 [kvm]
[ 208.224959] [c000200cdd98fb90] [c0080000075b495c] kvmppc_xive_native_set_attr+0x8b4/0x1480 [kvm]
[ 208.224967] [c000200cdd98fca0] [c00800000759261c] kvm_device_ioctl_attr+0x64/0xb0 [kvm]
[ 208.224974] [c000200cdd98fcf0] [c008000007592730] kvm_device_ioctl+0xc8/0x110 [kvm]
[ 208.224979] [c000200cdd98fd10] [c000000000433a24] do_vfs_ioctl+0xd4/0xcd0
[ 208.224981] [c000200cdd98fdb0] [c000000000434724] ksys_ioctl+0x104/0x120
[ 208.224984] [c000200cdd98fe00] [c000000000434768] sys_ioctl+0x28/0x80
[ 208.224988] [c000200cdd98fe20] [c00000000000b888] system_call+0x5c/0x70
legoater@boss01:~$
Fixes: 13ce3297c5 ("KVM: PPC: Book3S HV: XIVE: Add controls for the EQ configuration")
Fixes: e6714bd167 ("KVM: PPC: Book3S HV: XIVE: Add a control to dirty the XIVE EQ pages")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The XICS-on-XIVE KVM device needs to allocate XIVE event queues when a
priority is used by the OS. This is referred as EQ provisioning and it
is done under the hood when :
1. a CPU is hot-plugged in the VM
2. the "set-xive" is called at VM startup
3. sources are restored at VM restore
The kvm->lock mutex is used to protect the different XIVE structures
being modified but in some contexts, kvm->lock is taken under the
vcpu->mutex which is not permitted by the KVM locking rules.
Introduce a new mutex 'lock' for the KVM devices for them to
synchronize accesses to the XIVE device structures.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Show the '^' character when a policy rule has flag IMA_INMASK.
Fixes: 80eae209d6 ("IMA: allow reading back the current IMA policy")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
This patch prevents memory access beyond the evm_tfm array by checking the
validity of the index (hash algorithm) passed to init_desc(). The hash
algorithm can be arbitrarily set if the security.ima xattr type is not
EVM_XATTR_HMAC.
Fixes: 5feeb61183 ("evm: Allow non-SHA1 digital signatures")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
When the event queue is full of phy up and down events and reached the
threshold, we will queue a shutdown-event, and set phy->in_shutdown so that
we will not queue a shutdown-event again. But before the shutdown-event can
be executed, every phy-down event will clear
phy->in_shutdown and a new shutdown-event will be queued. The queue will
be full of these shutdown-events.
Fix this by only clear phy->in_shutdown in sas_phye_shutdown(), that is
after the first shutdown-event has been executed.
Fixes: f12486e06a ("scsi: libsas: shut down the PHY if events reached the threshold")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If alloc_workqueue fails in alua_init, it should return -ENOMEM, otherwise
it will trigger null-ptr-deref while unloading module which calls
destroy_workqueue dereference
wq->lock like this:
BUG: KASAN: null-ptr-deref in __lock_acquire+0x6b4/0x1ee0
Read of size 8 at addr 0000000000000080 by task syz-executor.0/7045
CPU: 0 PID: 7045 Comm: syz-executor.0 Tainted: G C 5.1.0+ #28
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1
Call Trace:
dump_stack+0xa9/0x10e
__kasan_report+0x171/0x18d
? __lock_acquire+0x6b4/0x1ee0
kasan_report+0xe/0x20
__lock_acquire+0x6b4/0x1ee0
lock_acquire+0xb4/0x1b0
__mutex_lock+0xd8/0xb90
drain_workqueue+0x25/0x290
destroy_workqueue+0x1f/0x3f0
__x64_sys_delete_module+0x244/0x330
do_syscall_64+0x72/0x2a0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 03197b61c5 ("scsi_dh_alua: Use workqueue for RTPG")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SME is enabled, the smartpqi driver won't work on the HP DL385 G10
machine, which causes the failure of kernel boot because it fails to
allocate pqi error buffer. Please refer to the kernel log:
....
[ 9.431749] usbcore: registered new interface driver uas
[ 9.441524] Microsemi PQI Driver (v1.1.4-130)
[ 9.442956] i40e 0000:04:00.0: fw 6.70.48768 api 1.7 nvm 10.2.5
[ 9.447237] smartpqi 0000:23:00.0: Microsemi Smart Family Controller found
Starting dracut initqueue hook...
[ OK ] Started Show Plymouth Boot Scre[ 9.471654] Broadcom NetXtreme-C/E driver bnxt_en v1.9.1
en.
[ OK ] Started Forward Password Requests to Plymouth Directory Watch.
[[0;[ 9.487108] smartpqi 0000:23:00.0: failed to allocate PQI error buffer
....
[ 139.050544] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 139.589779] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts
Basically, the fact that the coherent DMA mask value wasn't set caused the
driver to fall back to SWIOTLB when SME is active.
For correct operation, lets call the dma_set_mask_and_coherent() to
properly set the mask for both streaming and coherent, in order to inform
the kernel about the devices DMA addressing capabilities.
Signed-off-by: Lianbo Jiang <lijiang@redhat.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the user tries to remove a zfcp port via sysfs, we only rejected it if
there are zfcp unit children under the port. With purely automatically
scanned LUNs there are no zfcp units but only SCSI devices. In such cases,
the port_remove erroneously continued. We close the port and this
implicitly closes all LUNs under the port. The SCSI devices survive with
their private zfcp_scsi_dev still holding a reference to the "removed"
zfcp_port (still allocated but invisible in sysfs) [zfcp_get_port_by_wwpn
in zfcp_scsi_slave_alloc]. This is not a problem as long as the fc_rport
stays blocked. Once (auto) port scan brings back the removed port, we
unblock its fc_rport again by design. However, there is no mechanism that
would recover (open) the LUNs under the port (no "ersfs_3" without
zfcp_unit [zfcp_erp_strategy_followup_success]). Any pending or new I/O to
such LUN leads to repeated:
Done: NEEDS_RETRY Result: hostbyte=DID_IMM_RETRY driverbyte=DRIVER_OK
See also v4.10 commit 6f2ce1c6af ("scsi: zfcp: fix rport unblock race
with LUN recovery"). Even a manual LUN recovery
(echo 0 > /sys/bus/scsi/devices/H:C:T:L/zfcp_failed)
does not help, as the LUN links to the old "removed" port which remains
to lack ZFCP_STATUS_COMMON_RUNNING [zfcp_erp_required_act].
The only workaround is to first ensure that the fc_rport is blocked
(e.g. port_remove again in case it was re-discovered by (auto) port scan),
then delete the SCSI devices, and finally re-discover by (auto) port scan.
The port scan includes an fc_rport unblock, which in turn triggers
a new scan on the scsi target to freshly get new pure auto scan LUNs.
Fix this by rejecting port_remove also if there are SCSI devices
(even without any zfcp_unit) under this port. Re-use mechanics from v3.7
commit d99b601b63 ("[SCSI] zfcp: restore refcount check on port_remove").
However, we have to give up zfcp_sysfs_port_units_mutex earlier in unit_add
to prevent a deadlock with scsi_host scan taking shost->scan_mutex first
and then zfcp_sysfs_port_units_mutex now in our zfcp_scsi_slave_alloc().
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: b62a8d9b45 ("[SCSI] zfcp: Use SCSI device data zfcp scsi dev instead of zfcp unit")
Fixes: f8210e3488 ("[SCSI] zfcp: Allow midlayer to scan for LUNs when running in NPIV mode")
Cc: <stable@vger.kernel.org> #2.6.37+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With this early return due to zfcp_unit child(ren), we don't use the
zfcp_port reference from the earlier zfcp_get_port_by_wwpn() anymore and
need to put it.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: d99b601b63 ("[SCSI] zfcp: restore refcount check on port_remove")
Cc: <stable@vger.kernel.org> #3.7+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ip_dev_find() can return NULL so add a check for NULL pointer.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlzu9swACgkQlvcN/ahK
BwqUOwgAj4S9jbhER39gl+ifvrL8cCc7tq5H5LxSElinu/RMnzKWmdXZ9Z5aiIdq
QLVSe1cg90sad/0zeha4E9HOzKiIOdWMIv++OToIwToAfmpl2DgY0UcUbiqkQEuA
aae3T1E6tDfTYKmqxUhqolE1ZvxmLLVyjV9KOVE4HUuSsLIRr5d8eyrjJPkC/dGY
lKhsHz80oi8X8sPx/CA6Xk1uAVoPCOh4mFPovqOJepl9DnStw8QxeoBzMAqoKBPo
evyI6+HeI3Bh8IyPs1x7NJsNYAbiuAGMuOgKNohPqO+CAIsOLV26fUWwZfpwxBuA
1+x+gckxPeHsKJS6AMcMk8gSyPBk/w==
=6Adp
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2019-05-29' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
qxl: Drop WARN when u/s tries to mmap a prime buffer (Gerd)
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190529211833.GA195708@art_vandelay
our extensions and, thus, the documentation build in general. Who knew
that those deprecation warnings it was outputting actually meant we should
change something? This set of fixes makes the build work again with
Sphinx 2.0 and eliminates the warnings for 1.8. As part of that, we also
need a few fixes to the docs for places where the new Sphinx is more
strict.
It is a bit late in the cycle for this kind of change, but it does fix
problems that people are experiencing now.
There has been some talk of raising the minimum version of Sphinx we
support. I don't want to do that abruptly, though, so these changes add
some glue to continue to support versions back to 1.3. We will be adding
some infrastructure soon to nudge users of old versions forward, with the
idea of maybe increasing our minimum version (and removing this glue)
sometime in the future.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAlzsYw8PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YGuwH+gOk2lGPpI7tsIsctUr3TTviYbu9EywGINUA
c2pPQBHbC13F/QKkb/WArnIhM7eRMWxNy1IlrzqTTLRcAteJihoRNldLVpImxwHJ
DaULovUHRO9uNuVORGV4RLOBUUkrguoz4X7OZooT3tluRZcL58C3Qn8MbZYiZYf1
ZJKHVJxfSedyHYTK1H5qB9uAAvdoNGLjvK8pzA9S7HgHM9viuOlY2GTHn4uvlmI+
qgnbVRNeEb8IRFztvKy2RyMAisx2o5v/lfpKVM+OC9EJgkpw+mw55YUdfDeNavJg
2d3xv8zgS1TP+qAmba2uVwiRDNChTKxz72nbaqZZGOt16StRiyY=
=hrKI
-----END PGP SIGNATURE-----
Merge tag 'docs-5.2-fixes2' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"The Sphinx 2.0 release contained a few incompatible API changes that
broke our extensions and, thus, the documentation build in general.
Who knew that those deprecation warnings it was outputting actually
meant we should change something? This set of fixes makes the build
work again with Sphinx 2.0 and eliminates the warnings for 1.8. As
part of that, we also need a few fixes to the docs for places where
the new Sphinx is more strict.
It is a bit late in the cycle for this kind of change, but it does fix
problems that people are experiencing now.
There has been some talk of raising the minimum version of Sphinx we
support. I don't want to do that abruptly, though, so these changes
add some glue to continue to support versions back to 1.3. We will be
adding some infrastructure soon to nudge users of old versions
forward, with the idea of maybe increasing our minimum version (and
removing this glue) sometime in the future"
* tag 'docs-5.2-fixes2' of git://git.lwn.net/linux:
drm/i915: Maintain consistent documentation subsection ordering
scripts/sphinx-pre-install: make it handle Sphinx versions
docs: Fix conf.py for Sphinx 2.0
docs: fix multiple doc build warnings in enumeration.rst
lib/list_sort: fix kerneldoc build error
docs: fix numaperf.rst and add it to the doc tree
doc: Cope with the deprecation of AutoReporter
doc: Cope with Sphinx logging deprecations
Max Uvarov says:
====================
net: phy: dp83867: add some fixes
v3: use phy_modify_mmd()
v2: fix minor comments by Heiner Kallweit and Florian Fainelli
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY_INTERFACE_MODE_RGMII_RXID is less then TXID
so code to set tx delay is never called.
Fixes: 2a10154abc ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy state machine calls _config_init just after
reset.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After reset SGMII Autoneg timer is set to 2us (bits 6 and 5 are 01).
That is not enough to finalize autonegatiation on some devices.
Increase this timer duration to maximum supported 16ms.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For supporting 10Mps speed in SGMII mode DP83867_10M_SGMII_RATE_ADAPT bit
of DP83867_10M_SGMII_CFG register has to be cleared by software.
That does not affect speeds 100 and 1000 so can be done on init.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected. Warn the user when the
PHY fails to boot the firmware and refuse to initialise.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call. This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If blk_mq_init_allocated_queue() fails, make sure to free the poll
stat callback struct allocated.
Signed-off-by: Jes Sorensen <jsorensen@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix the following sparse context imbalance regression introduced in
a patch that fixed sleeping function called from invalid context bug.
kbuild test robot reported on:
tree/branch: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-linus
Regressions in current branch:
drivers/usb/usbip/stub_dev.c:399:9: sparse: sparse: context imbalance in 'stub_probe' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:418:13: sparse: sparse: context imbalance in 'stub_disconnect' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:464:1-10: second lock on line 476
Error ids grouped by kconfigs:
recent_errors
├── i386-allmodconfig
│ └── drivers-usb-usbip-stub_dev.c:second-lock-on-line
├── x86_64-allmodconfig
│ ├── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_disconnect-different-lock-contexts-for-basic-block
│ └── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_probe-different-lock-contexts-for-basic-block
└── x86_64-allyesconfig
└── drivers-usb-usbip-stub_dev.c:second-lock-on-line
This is a real problem in an error leg where spin_lock() is called on an
already held lock.
Fix the imbalance in stub_probe() and stub_disconnect().
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fixes: 0c9e8b3cad ("usbip: usbip_host: fix BUG: sleeping function called from invalid context")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sh_eth_close() resets the MAC and then calls phy_stop()
so that mdio read access result is incorrect without any error
according to kernel trace like below:
ifconfig-216 [003] .n.. 109.133124: mdio_access: ee700000.ethernet-ffffffff read phy:0x01 reg:0x00 val:0xffff
According to the hardware manual, the RMII mode should be set to 1
before operation the Ethernet MAC. However, the previous code was not
set to 1 after the driver issued the soft_reset in sh_eth_dev_exit()
so that the mdio read access result seemed incorrect. To fix the issue,
this patch adds a condition and set the RMII mode register in
sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs.
Note that when I have tried to move the sh_eth_dev_exit() calling
after phy_stop() on sh_eth_close(), but it gets worse (kernel panic
happened and it seems that a register is accessed while the clock is
off).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Kselftest update for Linux 5.2-rc3 consists of
- Alexandre Belloni's fixes to rtc regressions introduced in kselftest
Makefile test run output refactoring work from Kees Cook.
- ftrace test checkbashisms fixes from Masami Hiramatsu
-----BEGIN PGP SIGNATURE-----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=zYD6
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- Alexandre Belloni's fixes to rtc regressions introduced in kselftest
Makefile test run output refactoring work from Kees Cook.
- ftrace test checkbashisms fixes from Masami Hiramatsu
* tag 'linux-kselftest-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: rtc: rtctest: specify timeouts
selftests/harness: Allow test to configure timeout
selftests/ftrace: Add checkbashisms meta-testcase
selftests/ftrace: Make a script checkbashisms clean
This patch fixes a complain about possible sleep during
spinlock aquired
"BUG: sleeping function called from invalid context at
include/crypto/algapi.h:426"
for the ctr(aes) and ctr(des) s390 specific ciphers.
Instead of using a spinlock this patch introduces a mutex
which is save to be held in sleeping context. Please note
a deadlock is not possible as mutex_trylock() is used.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
In cifs_read_allocate_pages, in case of ENOMEM, we go through
whole rdata->pages array but we have failed the allocation before
nr_pages, therefore we may end up calling put_page with NULL
pointer, causing oops
Signed-off-by: Roberto Bergantinos Corpas <rbergant@redhat.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXO303xQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qlb7AP4179SWPy9RFxvxyjTmpPFPL9oR0Q26
sOTyIBN99MUTsgEA0FNWz7/FWtFDa1wbh0tEVreaTQlKEeoIYF96dkN0iwE=
=BJgg
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"This fixes a memory leak from the error path in the event filter
logic"
* tag 'trace-v5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Avoid memory leak in predicate_parse()
to avoid screen corruption during modprobe.
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling sys_ni_syscall through a syscall_fn_t pointer trips indirect
call Control-Flow Integrity checking due to a function type
mismatch. Use SYSCALL_DEFINE0 for __arm64_sys_ni_syscall instead and
remove the now unnecessary casts.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Although a syscall defined using SYSCALL_DEFINE0 doesn't accept
parameters, use the correct function type to avoid indirect call
type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Syscall wrappers in <asm/syscall_wrapper.h> use const struct pt_regs *
as the argument type. Use const in syscall_fn_t as well to fix indirect
call type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now a063057d7c ("block: Fix a race between request queue removal and
the block cgroup controller") has been reverted, and blkcg_exit_queue()
won't be called in blk_cleanup_queue() any more.
So don't need to protect generic_make_request_checks() with
blk_queue_enter(), then the total mess can be cleaned.
37f9579f4c ("blk-mq: Avoid that submitting a bio concurrently with device
removal triggers a crash") is reverted.
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 498f6650ae ("block: Fix a race between the cgroup code and
request queue initialization") moves what blk_exit_queue does into
blk_cleanup_queue() for fixing issue caused by changing back
queue lock.
However, after legacy request IO path is killed, driver queue lock
won't be used at all, and there isn't story for changing back
queue lock. Then the issue addressed by Commit 498f6650ae doesn't
exist any more.
So move move blk_exit_queue into __blk_release_queue.
This patch basically reverts the following two commits:
498f6650ae block: Fix a race between the cgroup code and request queue initialization
24ecc35853 block: Ensure that a request queue is dissociated from the cgroup controller
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With gcc 4.1:
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_switch_fetching_mode’:
sound/firewire/fireface/ff-protocol-latter.c:97: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_begin_session’:
sound/firewire/fireface/ff-protocol-latter.c:170: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:197: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:205: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_finish_session’:
sound/firewire/fireface/ff-protocol-latter.c:214: warning: integer constant is too large for ‘long’ type
Fix this by adding the missing "ULL" suffixes.
Add the same suffix to the last constant, to maintain consistency.
Fixes: fd1cc9de64 ("ALSA: fireface: add support for Fireface UCX")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I don't think this is userspace visible but SIGKILL does not have
any si_codes that use the fault member of the siginfo union. Correct
this the simple way and call force_sig instead of force_sig_fault when
the signal is SIGKILL.
The two know places where synchronous SIGKILL are generated are
do_bad_area and fpsimd_save. The call paths to force_sig_fault are:
do_bad_area
arm64_force_sig_fault
force_sig_fault
force_signal_inject
arm64_notify_die
arm64_force_sig_fault
force_sig_fault
Which means correcting this in arm64_force_sig_fault is enough
to ensure the arm64 code is not misusing the generic code, which
could lead to maintenance problems later.
Cc: stable@vger.kernel.org
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: af40ff687b ("arm64: signal: Ensure si_code is valid for all fault signals")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We met another Acer Aspire laptop which has the problem on the
headset-mic, the Pin 0x19 is not set the corret configuration for a
mic and the pin presence can't be detected too after plugging a
headset. Kailang suggested that we should set the coeff to enable the
mic and apply the ALC269_FIXUP_LIFEBOOK_EXTMIC. After doing that,
both headset-mic presence and headset-mic work well.
The existing ALC255_FIXUP_ACER_MIC_NO_PRESENCE set the headset-mic
jack to be a phantom jack. Now since the jack can support presence
unsol event, let us imporve it to set the jack to be a normal jack.
https://bugs.launchpad.net/bugs/1821269
Fixes: 5824ce8de7 ("ALSA: hda/realtek - Add support for Acer Aspire E5-475 headset mic")
Cc: Chris Chiu <chiu@endlessm.com>
CC: Daniel Drake <drake@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a vCPU is connected to the KVM device, it is done using its vCPU
identifier in the guest. Fix the enforced limit on the vCPU identifier
by taking into account the SMT mode.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Tested-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When a CPU is hot-unplugged, the EQ is deconfigured using a zero size
and a zero address. In this case, there is no need to check the flag
and queue size validity. Move the checks after the queue reset code
section to fix CPU hot-unplug.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Tested-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Improve the release of the XIVE KVM device by clearing the file
address_space, which is used to unmap the interrupt ESB pages when a
device is passed-through.
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently the HV KVM code takes the kvm->lock around calls to
kvm_for_each_vcpu() and kvm_get_vcpu_by_id() (which can call
kvm_for_each_vcpu() internally). However, that leads to a lock
order inversion problem, because these are called in contexts where
the vcpu mutex is held, but the vcpu mutexes nest within kvm->lock
according to Documentation/virtual/kvm/locking.txt. Hence there
is a possibility of deadlock.
To fix this, we simply don't take the kvm->lock mutex around these
calls. This is safe because the implementations of kvm_for_each_vcpu()
and kvm_get_vcpu_by_id() have been designed to be able to be called
locklessly.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently the Book 3S KVM code uses kvm->lock to synchronize access
to the kvm->arch.rtas_tokens list. Because this list is scanned
inside kvmppc_rtas_hcall(), which is called with the vcpu mutex held,
taking kvm->lock cause a lock inversion problem, which could lead to
a deadlock.
To fix this, we add a new mutex, kvm->arch.rtas_token_lock, which nests
inside the vcpu mutexes, and use that instead of kvm->lock when
accessing the rtas token list.
This removes the lockdep_assert_held() in kvmppc_rtas_tokens_free().
At this point we don't hold the new mutex, but that is OK because
kvmppc_rtas_tokens_free() is only called when the whole VM is being
destroyed, and at that point nothing can be looking up a token in
the list.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently the HV KVM code uses kvm->lock in conjunction with a flag,
kvm->arch.mmu_ready, to synchronize MMU setup and hold off vcpu
execution until the MMU-related data structures are ready. However,
this means that kvm->lock is being taken inside vcpu->mutex, which
is contrary to Documentation/virtual/kvm/locking.txt and results in
lockdep warnings.
To fix this, we add a new mutex, kvm->arch.mmu_setup_lock, which nests
inside the vcpu mutexes, and is taken in the places where kvm->lock
was taken that are related to MMU setup.
Additionally we take the new mutex in the vcpu creation code at the
point where we are creating a new vcore, in order to provide mutual
exclusion with kvmppc_update_lpcr() and ensure that an update to
kvm->arch.lpcr doesn't get missed, which could otherwise lead to a
stale vcore->lpcr value.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Stephen Hemminger