We were cheating with our barriers; using the smp ones rather than the
real device ones. That was fine, until rpmsg came along, which is
used to talk to a real device (a non-SMP CPU).
Unfortunately, just putting back the real barriers (reverting
d57ed95d) causes a performance regression on virtio-pci. In
particular, Amos reports netbench's TCP_RR over virtio_net CPU
utilization increased up to 35% while throughput went down by up to
14%.
By comparison, this branch is in the noise.
Reference: https://lkml.org/lkml/2011/12/11/22
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (31 commits)
[S390] disassembler: mark exception causing instructions
[S390] Enable exception traces by default
[S390] return address of compat signals
[S390] sysctl: get rid of dead declaration
[S390] dasd: fix fixpoint divide exception in define_extent
[S390] dasd: add sanity check to detect path connection error
[S390] qdio: fix kernel panic for zfcp 31-bit
[S390] Add s390x description to Documentation/kdump/kdump.txt
[S390] Add VMCOREINFO_SYMBOL(high_memory) to vmcoreinfo
[S390] dasd: fix expiration handling for recovery requests
[S390] outstanding interrupts vs. smp_send_stop
[S390] ipc: call generic sys_ipc demultiplexer
[S390] zcrypt: Fix error return codes.
[S390] zcrypt: Rework length parameter checking.
[S390] cleanup trap handling
[S390] Remove Kerntypes leftovers
[S390] topology: increase poll frequency if change is anticipated
[S390] entry[64].S improvements
[S390] make arch/s390 subdirectories depend on config option
[S390] kvm: move cmf host id constant out of lowcore
...
Fix up conflicts in arch/s390/kernel/{smp.c,topology.c} due to the
sysdev removal clashing with "topology: get rid of ifdefs" which moved
some of that code around.
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move invalidate_bdev, block_sync_page into fs/block_dev.c. Export
kill_bdev as well, so brd doesn't have to open code it. Reduce
buffer_head.h requirement accordingly.
Removed a rather large comment from invalidate_bdev, as it looked a bit
obsolete to bother moving. The small comment replacing it says enough.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If an IO request is build on an alias device without prefix enabled
we try to calculate with zero data from the alias device. This
triggers a BUG statement with fixpoint divide exception.
This case is very unlikely and can only happen if the pathgroup is
lost with an alias device already in use.
Prevent the alias device from being used in this case.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Prevents possible data corruption by detecting cabling error.
Therefor read and compare the UID for all available channel paths.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The queue_start_poll function pointer field in struct qdio_initialize
had to change its type and become a vector of function pointers to
support asynchronous delivery of storage blocks so rename the field to
make the type change explicit and ensure no other user of qdio tries
to use the field the old way. During setting up the qdio queues, only
dereference vector elements if the vector is actually allocated.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The 'expires' value of a ccw requests defines how long the device
driver should wait for a response from the evice after the request has
been submitted to the channel subsystem. After the expiration time
(e.g. 30 seconds) the waiting request will be cancelled and started
again. This protects the DASD devices from beeing blocked by errors
that cause the answering I/O interrupt to be lost.
In case of error recovery requests, this 'expires' value used to be
set to 0, so in case of a lost interrupt, such a recovery request
would never expire and block the device. To prevent this kind of
problem, all recovery requests need to have an expires value > 0 as
well. If not specified otherwise, this should be the same expires
value as for the original request.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix length checking of the expected reply and remove re-adjustment of
expected control block length.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
drivers/s390/cio/qdio_setup.c:24:32:
warning: non-ANSI function declaration of function 'qdio_allocate_aob'
While at it also simplify the function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sysdev.h file should not be needed by any in-kernel code, so remove
the .h file from these random files that seem to still want to include
it.
The sysdev code will be going away soon, so this include needs to be
removed no matter what.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "Venkatesh Pallipadi
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
This moves the 'cpu sysdev_class' over to a regular 'cpu' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Userspace relies on events and generic sysfs subsystem infrastructure
from sysdev devices, which are made available with this conversion.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Len Brown <lenb@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If recovery is triggered in presence of pending asynchronous
deliveries of storage blocks we do a forced cleanup after
the corresponding tasklets are completely stopped and trigger
appropriate notifications for the correspondingerror state.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case there are no system resources to run a recovery we have to clear
recovery bitmasks so a further automatic or manual driven recovery can
fix up the device.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETIUCV device driver allows to connect a Linux guest on z/VM to
another z/VM guest based on the z/VM communication facility IUCV.
Multiple output paths to different guests are possible, as well as
multiple input paths from different guests.
With this feature, you can configure multiple point-to-point NETIUCV
interfaces between your Linux on System z instance and another z/VM
guest.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
zfcp_scsi_slave_destroy erroneously always tried to finish its task
even if the corresponding previous zfcp_scsi_slave_alloc returned
early. This can lead to kernel page faults on accessing uninitialized
fields of struct zfcp_scsi_dev in zfcp_erp_lun_shutdown_wait. Take the
port field of the struct to determine if slave_alloc returned early.
This zfcp bug is exposed by 4e6c82b (in turn fixing f7c9c6b to be
compatible with 21208ae) which can call slave_destroy for a
corresponding previous slave_alloc that did not finish.
This patch is based on James Bottomley's fix suggestion in
http://www.spinics.net/lists/linux-scsi/msg55449.html.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Cc: <stable@kernel.org> #2.6.38+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This include file is not needed for any driver to be referencing, so
remove it from the tape_class.h file.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reflect the fact that a refrence is not obtained to the
resulting neighbour entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
Setup timer for processing messages in request queue after a
successful AP bus device reset.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The functions called by chsc_chp_vary operate on pointers to channel
path ids not channel path links. (This worked by chance since the id
is the first member of the link structure)
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a driver wants to do command mode IO while CIO is doing
online path verification we ignore this request and provide
a fake irb when we are done and the driver can do IO again.
For transport mode IO we have no such mechanism, giving the
driver no other chance then to retry the action until we are
done. This is not very reliable.
Provide a fake irb for transport mode IO as well.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a driver requests to do IO, we will adjust the mask of
paths to be used to exclude varied offline paths.
Drivers trying to do IO solely on paths which are online but some
way defective may lack the information to do proper error handling.
There is no reason to allow the usage of known to be broken paths.
Thus restrict the paths a ccw driver can use for IO to a subset of
the paths cio found usable (this also excludes offline paths).
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Using the generic css_schedule_eval to evaluate subchannels
while resuming from hibernation is very slow when used with
many devices. Provide a new evaluation trigger which exploits
css_sched_sch_todo and use this in the resume callback for
ccw devices.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (86 commits)
ipv4: fix redirect handling
ping: dont increment ICMP_MIB_INERRORS
sky2: fix hang in napi_disable
sky2: enforce minimum ring size
bonding: Don't allow mode change via sysfs with slaves present
f_phonet: fix page offset of first received fragment
stmmac: fix pm functions avoiding sleep on spinlock
stmmac: remove spin_lock in stmmac_ioctl.
stmmac: parameters auto-tuning through HW cap reg
stmmac: fix advertising 1000Base capabilties for non GMII iface
stmmac: use mdelay on timeout of sw reset
sky2: version 1.30
sky2: used fixed RSS key
sky2: reduce default Tx ring size
sky2: rename up/down functions
sky2: pci posting issues
sky2: fix hang on shutdown (and other irq issues)
r6040: fix check against MCRO_HASHEN bit in r6040_multicast_list
MAINTAINERS: change email address for shemminger
pch_gbe: Move #include of module.h
...
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch avoids SIGA-r calls in case of SIGA-r required. It only calls
SIGA-r if a threshold of free buffer is reached. CPU consumption is
reduced as a consequence.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when use dst_get_neighbour to get neighbour, we need
rcu_read_lock to protect, since dst_get_neighbour uses
rcu_dereference.
Signed-off-by: David S. Miller <davem@davemloft.net>
Invocation of dev_alloc_name() is re-inserted, because the created
net_device name is used to create the device name for the iucv bus.
This device is created before the register_netdev call.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch "qeth: exploit asynchronous delivery of storage blocks"
added a WARN_ON in qeth_schedule_recovery. A device recovery should
not cause a kernel warning. This is obviously a debugging left-over
that we forgot to remove.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without appropriate configuration at the SE, a HiperSockets device
cannot be used for sniffing. Setting the sniffer attribute is rejected
with -EPERM.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new .bus_name to virtio_config_ops then modify virtio_net to
call through to it in an ethtool .get_drvinfo routine to report
bus_info in ethtool -i output which is consistent with other
emulated NICs and the output of lspci.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the kernel is started in kdump mode, zfcpdump should not be
initialized because both dump methods can't be used at the same time.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Setup timer for processing messages in request queue, if sending an AP
message returns with reason code AP_RESPONSE_RESET_IN_PROGRESS.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change them over to plain "ETHERNET"
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'for-3.2/core' of git://git.kernel.dk/linux-block: (29 commits)
block: don't call blk_drain_queue() if elevator is not up
blk-throttle: use queue_is_locked() instead of lockdep_is_held()
blk-throttle: Take blkcg->lock while traversing blkcg->policy_list
blk-throttle: Free up policy node associated with deleted rule
block: warn if tag is greater than real_max_depth.
block: make gendisk hold a reference to its queue
blk-flush: move the queue kick into
blk-flush: fix invalid BUG_ON in blk_insert_flush
block: Remove the control of complete cpu from bio.
block: fix a typo in the blk-cgroup.h file
block: initialize the bounce pool if high memory may be added later
block: fix request_queue lifetime handling by making blk_queue_cleanup() properly shutdown
block: drop @tsk from attempt_plug_merge() and explain sync rules
block: make get_request[_wait]() fail if queue is dead
block: reorganize throtl_get_tg() and blk_throtl_bio()
block: reorganize queue draining
block: drop unnecessary blk_get/put_queue() in scsi_cmd_ioctl() and blk_get_tg()
block: pass around REQ_* flags instead of broken down booleans during request alloc/free
block: move blk_throtl prototypes to block/blk.h
block: fix genhd refcounting in blkio_policy_parse_and_set()
...
Fix up trivial conflicts due to "mddev_t" -> "struct mddev" conversion
and making the request functions be of type "void" instead of "int" in
- drivers/md/{faulty.c,linear.c,md.c,md.h,multipath.c,raid0.c,raid1.c,raid10.c,raid5.c}
- drivers/staging/zram/zram_drv.c
Fix several compile errors on s390 caused by splitting module.h.
Some include additions [e.g. qdio_setup.c, zfcp_qdio.c] are in
anticipation of pending changes queued for s390 that increase
the modular use footprint.
[PG: added additional obvious changes since Heiko's original patch]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A kernel panic may occur during sending or receiving network packets
on a machine without adapter interrupts since commit d36deae.
The bug is triggered by writing to the shared indicator address which
is set to 0 if the machine doesn't have adapter interrupts.
Make the reading and setting of the shared indicator dependent on the
adapter interrupt feature and while at it move the code to the
file containing the adapter interrupt related code.
Thanks to Jan Jaeger for tracking this down.
Reported-by: Jan Jaeger <jan.jaeger@westnet.com.au>
Tested-by: Jan Jaeger <jan.jaeger@westnet.com.au>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
to_kvmdev and dev_to_virtio both use container_of. Avoid to nest the
two macros to quiet the following sparse warning:
drivers/s390/kvm/kvm_virtio.c:337:20: warning: symbol '__mptr' shadows an earlier one
drivers/s390/kvm/kvm_virtio.c:337:20: originally declared here
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix two NULL pointer warnings in the dasd driver:
drivers/s390/block/dasd_eckd.c:2353:20: warning: Using plain integer as NULL pointer
drivers/s390/block/dasd_eckd.c:2415:44: warning: Using plain integer as NULL pointer
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Mark the device as suspended and delay execution of the path
verification worker to prevent mix-up.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The multicast poll check for the outbound queue is redundant since
3d6c76f "[S390] qdio: outbound tasklet scan threshold". Remove the check.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't leave outbound SBALs in error state after a target full condition.
Reset the state to not initialized to make the error handling consistent
across all types of errors.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Running under z/VM with QIOASSIST enabled, qdio queues could stall if EQBS
did not extract all SBAL states. Add an instant retry for EQBS and, if the
retry fails, set up a timer to ensure outstanding SBALs are processed later.
While at it, optimize qdio_do_eqbs and qdio_do_sqbs to eliminate 3 jumps on
the hot path.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a timestamp per queue and update the timestamp when the queue is
scanned. Add the queue timestamps and the timestamp of the last
adapter interrupt to the debugfs output. The timestamps are useful
for debugging stall conditions.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The buffer for read configuration data has to be initialized with an
EBCDIC string to show support for extended UIDs to z/VM.
If this read configuration data CQR needs to be retried, the buffer
may have changed in between. So re-initialize the buffer to get a
correct extended UID under z/VM.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After terminating a request in the dasd_sleep_on_immediatly function,
wait for the clear interrupt to be received before starting the
new request. This prevents the requests from getting mixed up.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add missing module.h include to prevent build breakage after the
module.h split work hits Linus' tree.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for CHSC I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix coding style, remove forward declerations, simplify code.
Also remove a superfluous get_device/put_device pair in
ccwgroup_create_from_string.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Put sysfs attributes of ccwgroup devices in an attribute group to
ensure that these attributes are actually present when userspace
is notified via uevents.
Cc: stable@kernel.org
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Split out addressing mode bits from PSW_BASE_BITS, rename PSW_BASE_BITS
to PSW_MASK_BASE, get rid of psw_user32_bits, remove unused function
enabled_wait(), introduce PSW_MASK_USER, and drop PSW_MASK_MERGE macros.
Change psw_kernel_bits / psw_user_bits to contain only the bits that
are always set in the respective mode.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch provides the architecture specific part of the s390 kdump
support.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add access function for real memory needed by s390 kdump backend.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Print a message in case we do not receive an IRQ in time (for internal
I/O). Also print the ID of the last used channel path, since it is
possible that not the device itself but this specific path might have
a defect.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Current IRQ statistics support does not show detail counts for I/O
interrupts which are processed internally only. The result is a
summation count which is way off such as this one:
CPU0 CPU1 CPU2
I/O: 1331 710 442
[...]
QAI: 15 16 16 [I/O] QDIO Adapter Interrupt
QDI: 1 0 0 [I/O] QDIO Interrupt
DAS: 706 645 381 [I/O] DASD
C15: 26 10 0 [I/O] 3215
C70: 0 0 0 [I/O] 3270
TAP: 0 0 0 [I/O] Tape
VMR: 0 0 0 [I/O] Unit Record Devices
LCS: 0 0 0 [I/O] LCS
CLW: 0 0 0 [I/O] CLAW
CTC: 0 0 0 [I/O] CTC
APB: 0 0 0 [I/O] AP Bus
Fix this by moving I/O interrupt accounting into the common I/O layer.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
Ensure that adapter interrupts are correctly processed when they are
retrieved using TEST PENDING INTERRUPTION.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is very little benefit in allowing to let a ->make_request
instance update the bios device and sector and loop around it in
__generic_make_request when we can archive the same through calling
generic_make_request from the driver and letting the loop in
generic_make_request handle it.
Note that various drivers got the return value from ->make_request and
returned non-zero values for errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
FICON Express8S supports hardware data router, which requires an
adapted qdio request format.
This part 2/2 exploits the functionality in zfcp.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FICON Express8S supports hardware data router, which requires an
adapted qdio request format.
This part 1/2 provides the qdio base required for exploitation in
zfcp.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
DIF/DIX support for zfcp is no longer experimental,
and config option is no longer necessary.
Return error from queuecommand for unsupported data directions.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make sure that only assigned storage increments are unassigned when
attaching a storage element.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Data is only used to temporarily hold information to be copied to the user
level, so it should be freed before leaving the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch extends the HiperSockets device driver to send and receive
af_iucv traffic over HiperSockets transport.
TX: Driver uses new asynchronous delivery of storage blocks to pass
flow control/congestion information from the HiperSockets microcode
to the af_iucv socket.
RX: Memory for incoming traffic is preallocated and passed to
HiperSockets layer. If receiver is not capable to clean its buffers
shared with HiperSockets and pass new memory to the HiperSockets
layer this will cause flow control/congestion events on the
sender.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exploits the QDIO support for asynchronous delivery of storage
blocks for Hipersockets. The exploitation is not configured per default and
may be enabled via the function qeth_configure_cq.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that signal adapter commands are issued if they are
indicated to be required.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that signal adapter commands are issued if they are
indicated to be required.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces support for asynchronous delivery of storage blocks for
Hipersockets. Upper layers may exploit this functionality to reuse SBALs for
which the delivery status is still pending.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OSA cards can be configured to support 1 or 4 output queues. This
does not apply to HiperSockets. This patch limits determination of
the configured number of output queues to OSA cards only, but excludes
HiperSockets.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In layer 3 mode IPv6 over VLAN does not work on newer OSA levels in
case the sender and receiver run on the same (shared) OSA adapter.
Keep vlan info in the skb so the qdio header is filled with the
required vlan tag.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the code for getting an unsigned long from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This patch replaces the code for getting an unsigned long from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
To use raw track access some special storage server commands are
needed. Older storage hardware may not support these commands.
So check if raw track access is possible while setting the DASD
online.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The size of the buffer that is used to store DASD statistics input
strings depends on the user input. If the input string is to large,
the write operation could fail with -ENOMEM. To avoid this, use
vmalloc instead of kmalloc.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The SIGA-W may return with the busy bit set which means the device was
blocked. The busy loop which retries the SIGA-W for 100us may not be
long enough when running under a heavily loaded hypervisor.
Extend the retry mechanism by adding a longer second stage which retries
the SIGA-W for up to 10s. In difference to the first retry loop the second
stage is using mdelay to stop the cpu between the retries and thereby
avoid additional preassure in on the hypervisor.
If the second stage retry is successfull a device reset is avoided.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch extends the DASD statistics to allow for a more detailed
analysis of DASD I/O operations. In particular we want the statistics
to provide answers to the following questions:
- How many requests used a PAV alias?
- How many requests used High Performance FICON?
- How do read request perform versus write requests?
The existing DASD statistics interface has several shortcomings
- The interface for global data is a formatted text table in procfs
(/proc/dasd/statistics). The layout is meant for human readers and
is not to easy to parse. If values get to large for the table
layout, they get scaled down.
- The statistics which are collected per block device can be
accessed via an ioctl interface, which can only be extended by
defining a new ioctl.
- There is no statistics interface for individual PAV base and alias
devices.
To overcome theses shortcomings we create a new DASD statistics
interface in debugfs. This interface will contain one entry for global
data, one per DASD block device, and one per DASD base and alias
device. Each file contains the statistic data in easy to parse
name/value and name/array pairs. The existing interfaces will remain
functional, but they will not be extended.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add toleration support for ap devices with device type 10.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The following race can occur with qdio devices that use the shared device
state change indicator:
Device (Shared DSCI) CPU0 CPU1
===============================================================================
1. DSCI 0 => 1,
INT pending
2. Thinint handler
* si_used = 1
* Inbound tasklet_schedule
* DSCI 1 => 0
3. DSCI 0 => 1,
INT pending
4. Thinint handler
* si_used = 1
* Inbound tasklet_schedu
le
=> NOP
5. Inbound tasklet run
6. DSCI = 1,
INT surpressed
7. DSCI 1 => 0
The race would lead to a stall where new data in the input queue is
not recognized so the device stops working in case of no further traffic.
Fix the race by resetting the DSCI before scheduling the inbound tasklet
so the device generates an interrupt if new data arrives in the above
scenario in step 6.
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (51 commits)
PM: Improve error code of pm_notifier_call_chain()
PM: Add "RTC" to PM trace time stamps to avoid confusion
PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
PM / Suspend: Add .suspend_again() callback to suspend_ops
PM / OPP: Introduce function to free cpufreq table
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
...
- unify vlan and nonvlan rx path
- kill card->vlangrp and qeth_l3_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables pm_notifier_call_chain() to get the actual error code
in the callback rather than always assume -EINVAL by converting all
PM notifier calls to return encapsulate error code with
notifier_from_errno().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qdio SBAL entry flag is made-up of four different values that are
independent of one another. Some of the bits are reserved by the
hardware and should not be changed by qdio. Currently all four values
are overwritten since the SBAL entry flag is defined as an u32.
Split the SBAL entry flag into four u8's as defined by the hardware
and don't touch the reserved bits.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge irq.c and s390_ext.c into irq.c. That way all external interrupt
related functions are together.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Interrupt sources like pfault, sclp, dasd_diag and virtio all use the
service signal external interrupt subclass mask in control register 0
to enable and disable the corresponding interrupt.
Because no reference counting is implemented each subsystem thinks it
is the only user of subclass and sets and clears the bit like it wants.
This leads to case that unloading the dasd diag module under z/VM
causes both sclp and pfault interrupts to be masked. The result will
be locked up system sooner or later.
Fix this by introducing a new way to set (register) and clear
(unregister) the service signal subclass mask bit in cr0.
Also convert all drivers.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide sysfs attributes that contain the CPC name and the HMC network
name of the machine the operating system is running on. This information
is retrieved with the operation communication parameters (OCF) sclp
interface.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Update affected channel path descriptors when receiving channel path
availability information.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Prevent the following compile warning for !CONFIG_64BIT:
CC drivers/s390/cio/qdio_main.o
drivers/s390/cio/qdio_main.c: In function ‘handle_outbound’:
drivers/s390/cio/qdio_main.c:1449: warning: ‘state’ may be used uninitialized in this function
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sendmask check is not needed. Remove it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The registration of an ap device will be skipped, if the device type
probing fails.
Add names of current crypto adapters to the Kconfig help.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Return codes are on purpose not handled or used. So remove them.
Acked-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix return code handling within monwrite_new_hdr(). Return code handling
is everwhere implemented, the return code of the diagnose function was
just not passed.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Check return value of itcw_add_dcw() for error code and return it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the tape block device driver. It's not of real use but has
already created some confusion when users wanted to access tape devices
and used the block device nodes instead of the character device nodes.
Also remove the whole tape documentation since it's completely outdated
and we have the device drivers book which is the place where everything
is properly documented.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In ccw_device_set_online we basically start path verification and
wait for the device to reach a final state. If it turns out that the
device has no useable path we schedule the deregistration of the
device (which is still in an non-final state) and wake up the waiting
process. The deregistration process will set a final state, but if
the wake up happens to be prior to this, the device will hang forever
in ccw_device_set_online.
To fix this just set the final NOT_OPER state prior to the scheduled
deregistration of the device.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
This patch uses the ndo_set_features callback during normal device
startup or recovery to turn on hardware RX checksum. Patch was done
with much help from Michal Miroslaw, thx!!!
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: don't delay blk_run_queue_async
scsi: remove performance regression due to async queue run
blk-throttle: Use task_subsys_state() to determine a task's blkio_cgroup
block: rescan partitions on invalidated devices on -ENOMEDIA too
cdrom: always check_disk_change() on open
block: unexport DISK_EVENT_MEDIA_CHANGE for legacy/fringe drivers
-Wunused-but-set-variable generates compile warnings. The affected
variables are removed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-Wunused-but-set-variable generates a compile warning for lcs' tasklet
function. Invoked functions contain already error handling; thus
additional return code checking is not needed here.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused return code handling. The claw driver is mostly dead, so
just make sure it keeps compiling without warnings.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill in the owner of qeth's ccw device driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves FFDC (first failure data capture) by requesting
a hardware trace in case the device driver, the hardware or a user
detects an error.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set rx csum default to hw checksumming again.
Remove sysfs interface for rx csum (checksumming) and TSO (large_send).
With the new hw_features it does not work to keep the old sysfs
interface in parallel. Convert options.checksum_type to new hw_features.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The termination of running CQR caused by reserve/release operations
may lead to an IO error if reserve/release is done in a tight loop.
Prevent this by increasing the retry counter after termination.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix initial usecount of attached and assigned storage increments so
they can be set offline.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Force dev_alloc_name() to be called from register_netdevice() by
dev_get_valid_name(). That allows to remove multiple explicit
dev_alloc_name() calls.
The possibility to call dev_alloc_name in advance remains.
This also fixes veth creation regresion caused by
84c49d8c3e
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pfault, dasd diag and virtio all use the same external interrupt number.
The respective interrupt handlers decide by the subcode if they are
meant to handle the interrupt.
Counting is currently done before looking at the subcode which means
each handler counts an interrupt even if it is not handling it.
Fix this by moving the kstat code after the code which looks at the
subcode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In-kernel disk event polling doesn't matter for legacy/fringe drivers
and may lead to infinite event loop if ->check_events() implementation
generates events on level condition instead of edge.
Now that block layer supports suppressing exporting unlisted events,
simply leaving disk->events cleared allows these drivers to keep the
internal revalidation behavior intact while avoiding weird
interactions with userland event handler.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
options.large_send was easy to get rid of. options.checksum_type has deeper
roots so is left for later cleanup.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When evaluating sense data in dasd_eckd_check_for_device_change, we
must always check for the type of sense data in byte 27, bit 0, to
make sure that the rest of the sense data is interpreted correctly.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The qdio hardware may surpress further interrupts as long as a SBAL is in
the error state. That can lead to unnotified data in the SBALs following
the error state. To prevent this behaviour change the SBAL[s] in error
state immediately to another program owned state so interrupts are again
received for further traffic on the device.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd_open function uses the private_data pointer of the gendisk to
find the dasd_block structure that matches the gendisk. When a DASD
device is set offline, we set the private_data pointer of the gendisk
to NULL and later remove the dasd_block structure, but there is still
a small race window, in which dasd_open could first read a pointer
from the private_data field and then try to use it, after the structure
has already been freed.
To close this race window, we will store a pointer to the dasd_devmap
structure of the base device in the private_data field. The devmap
entries are not deleted, and we already have proper locking and
reference counting in place, so that we can safely get from a devmap
pointer to the dasd_device and dasd_block structures of the device.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cio_ignore purge function is intended to only remove CCW devices
which are in the offline state. There is a time frame after the purge
function finished where a CCW device is scheduled for removal but
still accessible. When the device is set online during this time
frame, it may first appear online before it is then removed.
Fix this by preventing that CCW devices can be set online while there
is work (such as removal triggered by the purge function) for it
pending. Also ensure that the purge function does not schedule devices
for removal which are in the process of being set online.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reorder the initialization sequence of the qdio module to avoid
writing to an uninitialized debug feature entry. Also reorder
the exit function to restore a consistent cleanup path.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] cmpxchg: implement cmpxchg64()
[S390] xchg/cmpxchg: move to own header file
[S390] ccwgroup_driver: remove duplicate members
[S390] ccw_bus_type: make it static
[S390] ccw_driver: remove duplicate members
[S390] qdio: prevent handling of buffers if count is zero
[S390] setup: register bss section as resource
[S390] setup: simplify setup_resources()
[S390] wire up sys_syncfs
[S390] wire up sys_clock_adjtime
[S390] wire up sys_open_by_handle_at
[S390] wire up sys_name_to_handle_at
[S390] oprofile: disable hw sampling for CONFIG_32BIT
[S390] early: limit savesys cmd string handling
[S390] early: Fix possible overlapping data buffer
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
Remove the owner and name members of struct
ccwgroup_driver and convert all drivers to store
this data in the embedded struct device_driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rusty Russell