Using newer backing devices can cause the required padding at the end of
buffer as well as the number of queues to change after a failover.
Since we currently assume that these values never change, after a
failover to a backing device with different capabilities, we can get
errors from the vnic server, attempt to free long term buffers that are
no longer there, or not free long term buffers that should be freed.
This patch resolves the issue by checking whether any of these values
change, and if so perform the necessary re-allocations.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet descriptor generation for IPv6 is broken.
Properly set L3 and L4 protocol flags for IPv6 descriptors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set some missing fields in the IP control offload buffer. This buffer is
used to enable checksum and TCP segmentation offload in the VNIC server.
The buffer length field and the checksum offloading bits were not set
properly, so fix that here.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to architecture limitations, the IBM VNIC client driver is unable
to perform MAC address changes unless the device has "logged in" to
its backing device. Currently, pending MAC changes are handled before
login, resulting in an error and failure to change the MAC address.
Moving that chunk to the end of the ibmvnic_login function, when we are
sure that it was successful, fixes that.
The MAC address can be changed when the device is up or down, so
only check if the device is in a "PROBED" state before setting the
MAC address.
Fixes: c26eba03e4 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the dma_mapping_error call to use the correct dma_addr
which is inside the ibmvnic_vpd struct. Moreover, it fixes an uninitialized
warning regarding a local dma_addr variable which is not used anymore.
Fixes: 4e6759be28 ("ibmvnic: Feature implementation of VPD for the ibmvnic driver")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements and enables VDP support for the ibmvnic driver.
Moreover, it includes the implementation of suitable structs, signal
transmission/handling and functions which allows the retrival of firmware
information from the ibmvnic card through the ethtool command.
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the login buffer to include client data for the vnic driver,
this includes the OS name, LPAR name, and device name. This update
allows this information to be available in the VIOS.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For all non-fatal reset conditions, the hypervisor will send a failover when
we attempt to initialize the crq and the vnic client is expected to handle
that failover instead of the existing non-fatal reset. To handle this, we
need to return from init with a return code that indicates that we have hit
this case.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ibmvnic reset infrastructure to include a new reset option that will
allow changing of tunable parameters. There currently is no way to request
different capabilities from the vnic server on the fly so this patch
achieves this by resetting the driver and attempting to log in with the
requested changes. If the reset operation fails, the old values of the
tunable parameters are stored in the "fallback" struct and we attempt to
login with the fallback values.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables TSO support. It includes additional
buffers reserved exclusively for large packets. Throughput
is greatly increased with TSO enabled, from about 1 Gb/s to
9 Gb/s on our test systems.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables scatter gather support. Since there is no
HW/FW scatter-gather support at this time, the driver needs to
loop through each fragment and copy it to a contiguous, pre-mapped
buffer entry.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch correctly sets the number of additional header descriptors
that will be sent in an indirect SCRQ entry.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State is initially reported as UNKNOWN. Before register call
netif_carrier_off(). Once the device is opened, call netif_carrier_on() in
order to set the state to UP.
Signed-off-by: Mick Tarsel <mjtarsel@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with
const vio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a248878d7a ("ibmvnic: Check for transport event on driver resume")
removed the loop to kick irqs on driver resume but didn't remove the now
unused loop variable 'i'.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease debugging of the ibmvnic driver add a series of netdev_dbg()
statements to track driver status, especially during initialization,
removal, and resetting of the driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that any resources allocated during probe are released if the
probe of the driver fails.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reporting any return code for a receive buffer as an "rx error" only
produces alarming noise and the only values that have been observed to be
used in this field are not error conditions. Change this to a netdev_dbg
with a more descriptive message.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .get_channels (ethtool -l) functionality
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .get_ringparam (ethtool -g) functionality
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vnic server reports the statistics buffer in big endian format and must
be converted to cpu endian in order to be displayed correctly on little
endian lpars.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add counters to report number of packets, bytes, and dropped packets for
each transmit queue and number of packets, bytes, and interrupts for each
receive queue. Modify ethtool callbacks to report the new statistics.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCRQ resources are freed during renegotiation, but they are not
re-allocated afterwards due to some changes in the initialization
process. Fix that by re-allocating the memory after renegotation.
SCRQ's can also be freed if a server capabilities request fails.
If this were encountered during a device reset for example,
SCRQ's may not be re-allocated. This operation is not necessary
anymore so remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On resume, the ibmvnic driver will fail to resume normal operation.
The main crq gets closed on suspend by the vnic server and doesn't get
reopened again as the interrupt for the transport event that would reset
the main crq comes in after the driver has been suspended.
This patch resolves the issue by removing the calls to kick the receive
interrupts handlers and instead directly invoking the main crq interrupt
handler. This will ensure that we see the transport event necessary to
properly resume the driver.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently creates RX/TX queues during device probe, but
assigns IRQ's to them during device open. On reset, however,
IRQ's are assigned when resetting the queues. If there is a reset
while the device is closed and the device is later opened, the driver will
request IRQ's twice, causing the open to fail. This patch assigns
the IRQ's in the ibmvnic_init function after the queues are reset or
initialized, ensuring IRQ's are only requested once.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The update to ibmvnic_init to allow an EAGAIN return code broke
the calling of ibmvnic_init from ibmvnic_probe. The code now
will return from this point in the probe routine if anything
other than EAGAIN is returned. The check should be to see if rc
is non-zero and not equal to EAGAIN.
Without this fix, the vNIC driver can return 0 (success) from
its probe routine due to ibmvnic_init returning zero, but before
completing the probe process and registering with the netdev layer.
Fixes: 6a2fb0e99f (ibmvnic: driver initialization for kdump/kexec)
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch stores the return code of the REQUEST_MAP_RSP sub-CRQ command
in the private data structure, where it can be later checked during
device open or a reset.
In the case of a reset, the mapping request to the vNIC Server may fail,
especially in the case of a partition migration. The driver attempts to
handle this by re-allocating the buffer and re-sending the mapping request.
The original error handling implementation was removed. The separate
function handling the REQUEST_MAP response message was also removed,
since it is now simple enough to be handled in the ibmvnic_handle_crq
function.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ibmvnic driver is not in the VNIC_OPEN state, return from
ibmvnic_resume callback. If we are not in the VNIC_OPEN state, interrupts
may not be initialized and directly calling the interrupt handler will
cause a crash.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When booting into the kdump/kexec kernel, pHyp and vios
are not prepared for the initialization crq request and
a failover transport event is generated. This is not
handled correctly.
At this point in initialization the driver is still in
the 'probing' state and cannot handle a full reset of the
driver as is normally done for a failover transport event.
To correct this we catch driver resets while still in the
'probing' state and return EAGAIN. This results in the
driver tearing down the main crq and calling ibmvnic_init()
again.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug where, in the case of a device reset,
the polling routine will never complete, causing napi_disable
to sleep indefinitely when attempting to close the device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a kernel panic resulting from data access of a NULL
pointer during device close. The pending_scrq routine is
meant to determine whether there is a valid sub-CRQ message
awaiting processing. When the device is closing, however,
there is a possibility that NULL messages can be processed
because pending_scrq will always return 1 even if there
no valid message in the queue.
It's not clear what this closing state check was originally
meant to accomplish, so just remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixup a typo so that the entire SCRQ buffer is cleaned.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_tx_disable to guarantee that TX queues are disabled
when __ibmvnic_close is called by the device reset routine.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX buffer pools are disabled while awaiting a device
reset if firmware indicates that the resource is closed.
This patch fixes a bug where pools were not being
subsequently enabled after the device reset, causing
the device to become inoperable.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling a driver reset due to a failover of the backing
server on the vios, doing the netdev_notify_peers() can cause
network traffic to stall or halt. Remove the netdev notify call
for failover resets.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IBM vNIC protocol provides support for the user to initiate
a failover from the client LPAR in case the current backing infrastructure
is deemed inadequate or in an error state.
Support for two H_VIOCTL sub-commands for vNIC devices are required
to implement this function. These commands are H_GET_SESSION_TOKEN
and H_SESSION_ERR_DETECTED.
"[H_GET_SESSION_TOKEN] is used to obtain a session token from a VNIC client
adapter. This token is opaque to the caller and is intended to be used in
tandem with the SESSION_ERROR_DETECTED vioctl subfunction."
"[H_SESSION_ERR_DETECTED] is used to report that the currently active
backing device for a VNIC client adapter is behaving poorly, and that
the hypervisor should attempt to fail over to a different backing device,
if one is available."
To provide tools access to this functionality the vNIC driver creates a
sysfs file that, when written to, will send a request to pHyp to failover
to a different backing device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the mtu is currently not supported in the ibmvnic driver.
Implement .ndo_change_mtu in the driver so that attempting to use ifconfig
to change the mtu will fail and present the user with an error message.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original author left the project and so far has not
responded to emails sent to the listed address.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ibmvnic driver is resetting, we can just reset the sub crqs
instead of releasing all of their resources and re-allocting them.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting the ibmvnic driver there is not a need to release
and re-allocate the resources for the tx and rx pools. These
resources can just be reset to avoid the re-allocations.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver reset operation occurs there is not a need to release
the CRQ resources and re-allocate them. Instead a reset of the CRQ
will suffice.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not want to process any receive frames if the ibmvnic_poll
routine is invoked while a reset is in process. Also, before
replenishing the rx pools in the ibmvnic_poll, we want to
make sure the adapter is not in the process of closing.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If H_CLOSED is returned, halt RX buffer replenishment activity
until firmware sends a notification that the driver can reset.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables transmissions and reports carrier off if xmit
function returns that the hardware TX queue is closed. The driver can
then await a signal from firmware to determine the correct reset method.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle non-fatal error conditions. The process to do this when
resetting the driver is to just do __ibmvnic_close followed by
__ibmvnic_open.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Allen