Enabling the LP1 suspend mode for Tegra devices.
Tested-by: Marc Dietrich <marvin24@gmx.de> # paz00 board
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable the HDMI output as well as DDC and hotplug detection on Beaver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Beaver uses the RT5640 audio CODEC. Instantiate this on the I2C bus, and
add the top-level "sound" node to hook everything together and provide a
"sound card" device.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use TEGRA_GPIO() macro to name all GPIOs referenced by GPIO properties,
and some interrupts properties. Use standard GPIO flag defines too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Replace /include/ (dtc) with #include (C pre-processor) for all Tegra DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.
This allows future use of #defines and header files in order to define
names for various constants, such as the IDs and flags in GPIO
specifiers. Use of those features will increase the readability of the
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add support for general-purpose LEDs present on Beaver
Signed-off-by: Eric Brower <ebrower@nvidia.com>
[swarren: put new node in correct sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra30's boot ROM masks the top 1MiB of RAM. Fix the memory node in
Beaver's DT file to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Adding the PM configuration of PMC when the platform support suspend
function.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds "non-removable" property of MMC host where the eMMC device
is for Tegra platform.
And the "keep-power-in-suspend" property was used for the SDIO device that
need this to go into suspend mode (e.g. BRCM43xx series).
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The GPIO pin of SD slot card detection should active low.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
No Tegra30 Platform is running PLL_P at another rate than 408MHz, nor is
any using any other PLL as UART source clock. Move attribute into SoC
level dtsi file to slim down board DT files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds support for Tegra30 Beaver board in upstream kernel.
Beaver board is a Tegra30 SoC based development board, it has
following features:
- T30 or T33 SoC (Qual core ARM Cortex A9)
- 2 GB DDR3L
- 16 GB EMMC
- 1 SD slot
- 1 USB Standart A port and 1 USB micro AB port
- PCI-E Gig Ethernet
- Audio input/output
- SATA port
- HDMI output
- UART and JTAG
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
