Replace dev_kfree_skb with dev_kfree_skb_any in vmnet3_tx_xmit which
can be called in hard irq and other contexts. vmnet3_tx_xmit only
frees skbs that it has dropped.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit d25f06ea46 "vmxnet3: fix netpoll race condition",
the vmxnet3 driver fails to build when CONFIG_PCI_MSI is disabled,
because it unconditionally references the vmxnet3_msix_rx()
function.
To fix this, use the same #ifdef in the caller that exists around
the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3's netpoll driver is incorrectly coded. It directly calls
vmxnet3_do_poll, which is the driver internal napi poll routine. As the netpoll
controller method doesn't block real napi polls in any way, there is a potential
for race conditions in which the netpoll controller method and the napi poll
method run concurrently. The result is data corruption causing panics such as this
one recently observed:
PID: 1371 TASK: ffff88023762caa0 CPU: 1 COMMAND: "rs:main Q:Reg"
#0 [ffff88023abd5780] machine_kexec at ffffffff81038f3b
#1 [ffff88023abd57e0] crash_kexec at ffffffff810c5d92
#2 [ffff88023abd58b0] oops_end at ffffffff8152b570
#3 [ffff88023abd58e0] die at ffffffff81010e0b
#4 [ffff88023abd5910] do_trap at ffffffff8152add4
#5 [ffff88023abd5970] do_invalid_op at ffffffff8100cf95
#6 [ffff88023abd5a10] invalid_op at ffffffff8100bf9b
[exception RIP: vmxnet3_rq_rx_complete+1968]
RIP: ffffffffa00f1e80 RSP: ffff88023abd5ac8 RFLAGS: 00010086
RAX: 0000000000000000 RBX: ffff88023b5dcee0 RCX: 00000000000000c0
RDX: 0000000000000000 RSI: 00000000000005f2 RDI: ffff88023b5dcee0
RBP: ffff88023abd5b48 R8: 0000000000000000 R9: ffff88023a3b6048
R10: 0000000000000000 R11: 0000000000000002 R12: ffff8802398d4cd8
R13: ffff88023af35140 R14: ffff88023b60c890 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff88023abd5b50] vmxnet3_do_poll at ffffffffa00f204a [vmxnet3]
#8 [ffff88023abd5b80] vmxnet3_netpoll at ffffffffa00f209c [vmxnet3]
#9 [ffff88023abd5ba0] netpoll_poll_dev at ffffffff81472bb7
The fix is to do as other drivers do, and have the poll controller call the top
half interrupt handler, which schedules a napi poll properly to recieve frames
Tested by myself, successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: stable@vger.kernel.org
Reviewed-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: pv-drivers@vmware.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This update cleans up the MSI-X/MSI enablement code, fixes
vmxnet3_acquire_msix_vectors() invalid return values and
enables a dead code in case VMXNET3_LINUX_MIN_MSIX_VECT
MSI-X vectors were allocated.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: pv-drivers@vmware.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent conversion to skb_set_hash() was incorrect. 'skb' is
uninitialized at this point.
Fixes: 0b68070347 ('net: vmxnet3 calls skb_set_hash')
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for virtual IOMMU to the vmxnet3 module. We
switch to DMA consistent mappings for anything we pass to the device.
There were a few places where we already did this, but using pci_blah();
these have been fixed to use dma_blah(), along with all new occurrences
where we've replaced kmalloc() and friends.
Also fix two small bugs:
1) use after free of rq->buf_info in vmxnet3_rq_destroy()
2) a cpu_to_le32() that should have been a cpu_to_le64()
Acked-by: George Zhang <georgezhang@vmware.com>
Acked-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux is free to call ethtool ops as soon as a netdev exists when probe
finishes. However, we only allocate vmxnet3 tx/rx queues and initialize the
rx_buf_per_pkt field in struct vmxnet3_adapter when the interface is
opened (UP).
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/ethtool.c
drivers/net/vmxnet3/vmxnet3_drv.c
drivers/net/wireless/iwlwifi/dvm/tx.c
net/ipv6/route.c
The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.
The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.
The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.
The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 fails to set netif_carrier_off on probe, meaning that when an interface
is opened the __LINK_STATE_NOCARRIER bit is already cleared, and so
/sys/class/net/<ifname>/operstate remains in the unknown state. Correct this by
setting netif_carrier_off on probe, like other drivers do.
Also, while we're at it, lets remove the netif_carrier_ok checks from the
link_state_update function, as that check is atomically contained within the
netif_carrier_[on|off] functions anyway
Tested successfully by myself
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VMXNET3 device provides RSS hash value for received packets,
but it is not being used.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than generating a different RSS key on each boot, just use
a predetermined value that will map same flow to same value on
every device for more predictable testing. This is already done
on most hardware drivers.
Initial key value just some arbitrary bits extracted once
from /dev/random.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This static variable is never set, it initializes to 0 which
is VMXNET3_INTR_BUDDYSHARE, and never changes.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An atomic counter of devices present is maintained but never used.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the standard netdev_xxx() and dev_xxx() wrappers to format
log messages.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_dbg() rather than dev_dbg() because the former prints
the device name which is more useful than the pci name.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This messages that occur during boot time from this device
when netdev_err is called before calling register_netdevice().
Switch to using dev_XXX macros which correlate message with PCI info which
is available.
Rather than fixing the features message, just remove it since
the information is redundant and available through ethtool.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The uncommitted[] array was set but never used except in a debug
message. Remove it.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_alloc_skb_align, rather than open code using dev_alloc_skb.
Change allocation at startup to use GFP_KERNEL.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: VMware, Inc. <pv-drivers@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 has a 16Kbytes limit per tx descriptor, that happened to work
as long as we provided PAGE_SIZE fragments.
Our stack can now build larger fragments, so we need to split them to
the 16kbytes boundary.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: jongman heo <jongman.heo@samsung.com>
Tested-by: jongman heo <jongman.heo@samsung.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_open() can complete before register_netdev() returns.
Fix vmxnet3_probe_device() to support this.
Signed-off-by: Steve Hodgson <steve@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix log messages and corrects some typos
Change logging of failure to enable MSI/MSI-X to display device's PCI
address instead of eth%d. Rectify a typo.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix transport header size
Fix the transpoert header size for UDP packets.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently shown that vmxnet3 devices on transmit, will drop very small udp
frames consistently. This is due to a regression introduced by commit
39d4a96fd7. This commit attempts to introduce an
optimization to the tx path, indicating that the underlying hardware behaves
optimally when at least 54 bytes of header data are available for direct access.
This causes problems however, if the entire frame is less than 54 bytes long.
The subsequent pskb_may_pull in vmxnet3_parse_and_copy_hdr fails, causing an
error return code, which leads to vmxnet3_tq_xmit dropping the frame.
Fix it by placing a cap on the copy length. For frames longer than 54 bytes, we
do the pull as we normally would. If the frame is shorter than that, copy the
whole frame, but no more. This ensures that we still get the optimization for
qualifying frames, but don't do any damange for frames that are too short.
Also, since I'm unable to do this, it wuold be great if vmware could follow up
this patch with some additional code commentary as to why 54 bytes is an optimal
pull length for a virtual NIC driver. The comment that introduced this was
vague on that. Thanks!
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Max Matveev <mmatveev@redhat.com>
CC: Max Matveev <mmatveev@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct spelling in "uncommited" to "uncommitted" in
drivers/net/vmxnet3/vmxnet3_drv.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use existing helpers to clarify skb headers manipulation.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that support modification of the RX flow hash indirection
table initialise it in the same way: RX rings are assigned to table
entries in rotation. Make that default policy explicit by having them
call a ethtool_rxfh_indir_default() function.
In the ethtool core, add support for a zero size value for
ETHTOOL_SRXFHINDIR, which resets the table to this default.
Partly-suggested-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The vmxnet3 driver enables vlan filters if filtering is enabled for
any vlan. In promiscuous mode the filter table is cleared to in
order to disable filtering. However, if a vlan device is subsequently
created that vlan will be added to the filter, re-engaging it. As a
result, not only do we not see all the vlans in promiscuous mode, we
don't even see vlans for which a filter was previously created.
CC: Scott J. Goldman <scottjg@vmware.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HIGHDMA is being disabled even when dma64 is true. This patch fixes it.
CC: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parent device for netdev should be set before netdev_info() can be called
otherwise there is a NULL pointer dereference and probe() fails.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>--
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 device supports only power-of-two number of queues. The driver
therefore needs to check this and rounds down the number of queues to the
nearest power of two.
Signed-off-by: Yong Wang <yongwang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
If the rx ring is completely empty, then the device may never fire an rx
interrupt. Unfortunately, the rx interrupt is what triggers populating the
rx ring with fresh buffers, so this will cause networking to lock up.
This patch replenishes the skb in recv descriptor as soon as it is
peeled off while processing rx completions. If the skb/buffer
allocation fails, existing one is recycled and the packet in hand is
dropped. This way none of the RX desc is ever left empty, thus avoiding
starvation
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving packets from another guest on the same hypervisor, it's
generally possible to receive large packets because no segmentation is
necessary and these packets are handled by LRO. However, when doing
routing or bridging we must disable LRO and lose this benefit. In
these cases GRO can still be used and it is very effective because the
packets which are segmented in the hypervisor are received very close
together and can easily be merged.
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: Scott Goldman <scottjg@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the vmxnet3 driver to use the new vlan model. In doing so
it fixes missing tags in tcpdump and failure to do checksum offload when
tx vlan offload is disabled.
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing some backporting I noticed that vmxnet3 had a variable that was set
but never used. Get rid of it, and stop the compiler from griping
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
Convert vmxnet3 driver to 64 bit statistics interface.
This driver was already counting packet per queue in a 64 bit value so not
a huge change. Eliminate unused old net_device_stats structure.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resending this patch with few changes.
Avoid multiple queues when MSI or MSI-X not available
Limit number of Tx queues to 1 if MSI/MSI-X support is not configured in
the kernel. This will make number of tx and rx queues equal when MSI/X
is not configured thus providing better performance.
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also removes private feature flags that were always set to true.
You may want to move vmxnet3_set_features() to vmxnet3_drv.c as a following
cleanup.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of single tx and rx queues, three MSI-x vectors are allocated instead
of two. This patch fixes that.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to cmd register is racey, especially in smp environments. Protect
it using a spinlock.
Signed-off-by: Matthieu Bucchianeri <matthieu@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small possibility of a race where the suspend routine gets
called, while a napi callback is still pending and when that comes up,
it enables interrupts which just got disabled in the suspend routine.
This change adds napi disable call in suspend and enable in resume to
avoid race.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a performance enhancement fix. vmxnet3 device performs better when
provided with at least 54 bytes (ethernet 14 + IP 20+ TCP 20) in the first SG
buffer. For UDP packets driver provides lesser than that in first sg. This
change fixes the same. Also avoid the redundant pskb_may_pull() call.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make hw vlan tag stripping as enabled by default. Thereby remove
the code to conditionally enable it later.
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While activating the device get it's MAC address from netdev. This will allow
the MAC address configured using ifconfig to persist through the reset.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug while changing ring size when MTU is changed.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>
There were several paths that didn't release their locks.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are using skb_transport_offset(skb) instead of skb->csum_start
for NETIF_F_HW_CSUM offload. This does not matter now, but if someone
implements checksumming of encapsulated packets then this will break silently.
TSO output paths are left as they are, since they are for IP+TCP only
(might be worth converting though).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_scheduled_work() is on its way out. This patch contains simple
conversions to replace flush_scheduled_work() usage with direct
cancels and flushes.
Directly cancel the used works on driver detach and flush them in
other cases.
The conversions are mostly straight forward and the only dangers are,
* Forgetting to cancel/flush one or more used works.
* Cancelling when a work should be flushed (ie. the work must be
executed once scheduled whether the driver is detaching or not).
I've gone over the changes multiple times but it would be much
appreciated if you can review with the above points in mind.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: netdev@vger.kernel.org
Add multiqueue support to vmxnet3 driver
This change adds multiqueue and thus receive side scaling support
to vmxnet3 device driver. Number of rx queues is limited to 1 in cases
where MSI is not configured or one MSIx vector is not available per rx
queue
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by sparse:
drivers/net/vmxnet3/vmxnet3_drv.c:876:38: warning: cast from restricted __be16
drivers/net/vmxnet3/vmxnet3_drv.c:876:38: warning: cast from restricted __be16
drivers/net/vmxnet3/vmxnet3_drv.c:876:24: warning: restricted __be16 degrades to integer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a le64, not a le32, typo in one place only.
Noticed by sparse:
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: warning: incorrect type in assignment (different base types)
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: expected restricted __le64 [usertype] confPA
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: got restricted __le32 [usertype] <noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's easier to just annotate the constants as little endian types and set/clear
the flags directly.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gcc doesn't usually handle inline across compilation units, and the
functions don't have to be global in scope. Move the set/reset flag
functions int the existing vmxnet3 header.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an overflow bug in vmxnet3 Tx descriptor
This patch fixes a bug where a 16K buffer on a Tx descriptor was overflowing
into the 'gen' bit in the descriptor thereby corrupting the descriptor and
stalling the transmit ring.
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Matthew Delco <delcoM@vmware.com>
Signed-off-by: Ronghua Zhang <ronghua@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respect the interrupt type set in VM configuration.
When interrupt type is not auto, do not ignore the interrupt type set from
VM configuration.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold rtnl_lock to get the right link state.
While asynchronously resetting the device, hold rtnl_lock to get the
right value from netif_running. If a reset is scheduled, and the device
goes thru close and open, it may happen that reset and open may run in
parallel. Holding rtnl_lock will avoid this.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change initializes the state of link at the time when driver is
loaded. The ethtool output for 'link detected' and 'link speed'
is thus valid even before the interface is brought up.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new bit map 'intrCtrl' is introduced in the DriverShared area. The
driver should update VMXNET3_IC_DISABLE_ALL bit before writing IMR.
Signed-off-by: Ronghua Zang <ronghua@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network drivers do not have to update last_rx, unless they need it for
their private use.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman