Check the aspeed timeout status register to see if the system has booted
from the secondary boot source. If so, set the watchdog device
bootstatus flag for "Card previously reset the CPU."
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the WDIOF_CARDRESET support for the Renesas platform
watchdog, to know if the board reboot is due to a watchdog reset.
This is done via the WOVF bit (bit 4) of the RWTCSRA register, which
indicates if RWTCNT overflowed, triggering the reset in last boot.
Signed-off-by: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
[takeshi.kihara.df: changed to read the RWTCSRA register while clock is
enabled]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"Fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"Fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case I replaced "Fall" with a proper
"Fall through" comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of
depending on it. This is merged with the same pattern
for all the ISA drivers and some other Kconfig cleanups
related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of
this SoC from the ARM tree.
- Move the documentation over to driver-api to conform with
the rest of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h>
that we want to get rid of.
- Managed to remove VLA allocation from two drivers pending
more fixes in this area for the next merge window.
- Misc janitorial fixes.
-----BEGIN PGP SIGNATURE-----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=C5t5
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJawdL2AAoJEGCrR//JCVInuH0P/RJAZh1nTD+TR34ZhJq2TBoo
PgygwDU7Z2+tQVU+EZ453Gywz9/NMRFk1RWAZqrLix4ZtyIMvC6A1qfT2yH1Y7Fb
Qh6tccQeLe4ezq5u4S/46R/fQXu3Txr92yVwzJJUuPyU0arF9rv5MmI8e6p7L1en
yb74kSEaCe+/eMlsEj1Cc1dgthDNXGKIURHkRsILoweysCpesjiTg4qDcL+yTibV
FP2wjVbniKESMKS6qL71tiT5sexvLsLwMNcGiHPj94qCIQuI7DLhLdBVsL5Su6gI
sbtgv0dsq4auRYAbQdMaH1hFvu6WptsuttIbOMnz2Yegi2z28H8uVXkbk2WVLbqG
ZESUwutGh8MzOL2RJ4jyyQq5sfo++CRGlfKjr6ImZRv03dv0pe/W85062cK5cKNs
cgDDJjGRorOXW7dyU6jG2gRqODOQBObIv3w5efdq5OgzOWlbI4EC+Y5u1Z0JF/76
pSwtGXA6YhwC+9LLAlnVTHG+yOwuLmAICgoKcTbzTVDKA2YQZG/cYuQfI5S1wD8e
X6urPx3Md2GCwLXQ9mzKBzKZUpu/Tuhx0NvwF4qVxy6x1PELjn68zuP7abDHr46r
57/09ooVN+iXXnEGMtQVS/OPvYHSa2NgTSZz6Y86lCRbZmUOOlK31RDNlMvYNA+s
3iIVHovno/JuJnTOE8LY
=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
clk_disable_unprepare() was added to one error path,
but there is another one. The patch makes sure clk is
disabled at the both of them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The blackfin architecture is getting removed, so this driver has
become obsolete.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allow the device tree to specify a watchdog to fallover to
the alternate boot source.
The aspeeed watchdog can set a latch directing flash chip select 0 to
chip select 1, allowing boot from an alternate media if the watchdog
is not reset in time. On the ast2400 bank 1 also goes to flash bank 1,
while on the ast2500 the chip selects are swapped.
Also clear the secondary boot bit during the machine restart operation.
Otherwise, the system will switch to the alternate boot after every
reboot, which is not desired.
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Nuvoton NPCM750 has a watchdog implemented as a single register
inside the timer peripheral.
This driver exposes that watchdog as a standard watchdog device with
coarse timeout intervals, limited by the combination of prescaler and
counter that is provided by the hardware. The calculation is taken from
the Nuvoton vendor tree.
The watchdog is left running if a bootloader had it going. The rate is
the one specified in the device tree, or the default value (obtained
from the datasheet).
There is a pre-timeout IRQ that is wired up. This timeout always occurs
1024 clocks before the timeout.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The resource allocation in WDAT watchdog has off-one-by error, it sets
one byte more than the actual end address. This may eventually lead
to unexpected resource conflicts.
Fixes: 058dfc7670 (ACPI / watchdog: Add support for WDAT hardware watchdog)
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqlyPEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGNa0H/RIa/StQuYu/SBwa
JRqQFmkIsx+gG+FyamJrqGzRfyjounES8PbfyaN3cCrzYgeRwMp1U/bZW6/l5tkb
OjTtrCJ6CJaa21fC/7aqn3rhejHciKyk83EinMu5WjDpsQcaF2xKr3SaPa62Ja24
fhawKq3CnUa+OUuAbicVX8yn4viUB6x8FjSN/IWfp3Cs4IBR7SGxxD7A4MET9FbQ
5OOu0al8ly9QeCggTtJyk+cApeLfexEBTbUur9gm7GcH9jhUtJSyZCZsDJx6M2yb
CwdgF4fyk58c1fuHvTFb0AdUns55ba3nicybRHHMVbDpZIG9v4/M1yJETHHf5cD7
t3rFjrY=
=+Ldf
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc5' into devel
Linux 4.16-rc5 merged into the GPIO devel branch to resolve
a nasty conflict between fixes and devel in the RCAR driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some platforms lose this state in suspend. It should be safe to do this
unconditionally.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
RK3399 has rst_pulse_length in CONTROL_REG[4:2], determining the length
of pulse to issue for system reset. We shouldn't clobber this value,
because that might make the system reset ineffective. On RK3399, we're
seeing that a value of 000b (meaning 2 cycles) yields an unreliable
(partial?) reset, and so we only fully reset after the watchdog fires a
second time. If we retain the system default (010b, or 8 clock cycles),
then the watchdog reset is much more reliable.
Read-modify-write retains the system value and improves reset
reliability.
It seems we were intentionally clobbering the response mode previously,
to ensure we performed a system reset (we don't support an interrupt
notification), so retain that explicitly.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If clk_prepare_enable(wdt->rtc_enable) fails,
wdt->enable clock is left enabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Assert RESET_SYSTEM bit for any reset and set MODE field from reset
type.
The watchdog control register has a RESET_SYSTEM bit that is really
closer to activate a reset, and RESET_SYSTEM_MODE field that chooses
how much to reset.
Before this patch, a node without these optional property would do a
SOC reset, but a node with properties requesting a cpu or SOC reset
would do nothing and a node requesting a system reset would do a
SOC reset.
Fixes: b7f0b8ad25 ("drivers/watchdog: ASPEED reference dev tree properties for config")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On iWave's boards iwg20d and iwg22d the only way to reboot the system is
by means of the watchdog.
This patch adds a restart handler to rwdt_ops, and also makes sure we
keep its priority to the lowest level, in order to not override other
more effective handlers.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Due to commits:
* "ARM: shmobile: Add watchdog support",
* "ARM: shmobile: rcar-gen2: Add watchdog support", and
* "soc: renesas: rcar-rst: Enable watchdog as reset trigger for Gen2",
we now have everything we needed for the watchdog to work on Gen2 and
RZ/G1.
However, on early revisions of some R-Car Gen2 SoCs, and depending on SMP
configuration, the system may fail to restart on watchdog time-out, and
lock up instead.
Specifically:
- On R-Car H2 ES1.0 and M2-W ES1.0, watchdog restart fails unless
only the first CPU core is in use (using e.g. the "maxcpus=1" kernel
commandline option).
- On R-Car V2H ES1.1, watchdog restart fails unless SMP is disabled
completely (using CONFIG_SMP=n during build configuration, or using
the "nosmp" or "maxcpus=0" kernel commandline options).
This commit adds "renesas,rcar-gen2-wdt" as compatible string for R-Car
Gen2 and RZ/G1, but also prevents the system from using the watchdog
driver in cases where the system would fail to restart by blacklisting
the affected SoCs, using the minimum known working revisions (ES2.0 on R-Car
H2, and ES3.0 on M2-W), and taking the actual SMP software configuration
into account.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
[Geert: blacklisting logic]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On R-Car Gen2 and RZ/G1 the watchdog IP clock needs to be always ON,
on R-Car Gen3 we power the IP down during suspend.
This commit adds suspend/resume support, so that the watchdog counting
"pauses" during suspend on all of the SoCs compatible with this driver
and on those we are now adding support for (R-Car Gen2 and RZ/G1).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
-----BEGIN PGP SIGNATURE-----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=zDIl
-----END PGP SIGNATURE-----
Merge tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag into asm-generic
Remove metag architecture
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
* tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
i2c: img-scb: Drop METAG dependency
media: img-ir: Drop METAG dependency
watchdog: imgpdc: Drop METAG dependency
MAINTAINERS/CREDITS: Drop METAG ARCHITECTURE
tty: Remove metag DA TTY and console driver
clocksource: Remove metag generic timer driver
irqchip: Remove metag irqchip drivers
Drop a bunch of metag references
docs: Remove remaining references to metag
docs: Remove metag docs
metag: Remove arch/metag/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that arch/metag/ has been removed, remove the METAG dependency from
the IMG IR device driver. The hardware is also present on MIPS SoCs so
the driver still has value.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Update driver version number to reflect changes.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a few dynamic debug messages to aid in module level debug.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make whether or not the hpwdt watchdog delivers a pretimeout NMI
programable by the user.
The underlying iLO hardware is programmable as to whether or not
a pre-timeout NMI is delivered to the system before the iLO resets
the system. However, the iLO does not allow for programming the
length of time that NMI is delivered before the system is reset.
By watchdog API, in hpwdt_set_pretimeout a val == 0 disables the NMI.
When val != 0, hpwdt_set_pretimeout will enable the pretimeout NMI
provided the current timeout is greator than the HW specified
pretimeout length. Otherwise an error is returned.
In set_timeout, if the new timeout is <= an already established pretimeout,
the pretimeout is canceled. This matches the action watchdog_set_timeout
in the watchdog core would do if an hpwdt specific set_timeout
function wasn't specified.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The intent of this parameter is unclear and it sets up a
race between the reset of the system by ASR and crashdump.
The length of time between receipt of the pretimeout NMI
and the ASR reset of the system is fixed by hardware.
Turning the parameter off doesn't necessairly prevent a crash dump.
Also, having the ASR reset occur while the system is crash dumping
doesn't imply that the dump was hung given the short duration
between the NMI and the reset.
This parameter is not a substitute for having a architected watchdog
crashdump hang detection paridigm.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Modify prior change to not claim an NMI unless originated
from iLO to apply only to iLO5 and later going forward.
This restores hpwdt traditional behavior of calling panic
if the NMI is NMI_IO_CHECK, NMI_SERR, or NMI_UNKNOWN for
legacy hardware.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Include the nmistat in the nmi_panic message to give support
an indication why the NMI was called (e.g. a timeout or generate
nmi button.)
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If devm_reset_control_get_exclusive() fails, asm9260_wdt_probe()
returns immediately. But clks has been already enabled at that point,
so it is required to disable them or to move the code around.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Licence text is specifying "GPLv2" but the MODULE_LICENSE is set to "GPLv2
or later".
See include/linux/module.h:
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
When on it, add SPDX identifier tag.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will preserve wdd->timeout value if
no parameter nor timeout-secs dt property is set.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will preserve wdd->timeout value if
no parameter nor timeout-secs dt property is set.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will preserve wdd->timeout value if no parameter
nor timeout-secs dt property is set.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
Following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt to make use of
the parameter logic.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
Following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt to make use of
the parameter logic.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Eddie James