If DW_MMC_CARD_NO_USE_HOLD isn't set, it's usesd by default.
Enve if SDMMC_CMD_USB_HOLD_REG is set in prepare_command(), but it
doesn't set in pre_stop_abort().
To maintain the consistency, add the checking condition for this.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If there is no property "clock-freq-min-max", mmc->f_min should be set
to 400K by default. But Some SoC can be used 100K.
When 100K is used, MMC core will try to check from 400K to 100K.
Reported-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If display the debug message, this message should be spamming.
If flags is maintained the previous value, didn't display the debug
message.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Developer wants to see the real register value, not register offset.
This patch fixed to display the real value of register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Trivial fix to spelling mistake "desciptor" to "descriptor" in
dev_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now there are no variant drivers using dw_mci_suspend
and dw_mci_resume, so let's remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We could disable biu clk if gpio card detect available,
or it is a non-removable device.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add dw_mci_runtime_suspend/resume interfaces
and expose it to dw_mci variant driver to support runtime
PM.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When dma->start is failed,then it has to fall back to PIO mode
for current transfer.
But Host controller was already set to bits relevant to DMA operation.
If needs to use the PIO mode, Host controller has to stop the DMA
operation. (It's more stable than now.)
When it occurred error, it's not running any request.
Fixes: 3fc7eaef44 ("mmc: dw_mmc: Add external dma interface support")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the "reset" as name of reset controller.
This is for preventing the wrong operation. Even if some SoC has reset
controller, doesn't define "resets" in device-tree.
Then it might be waiting for reset controller and it should be stuck.
Fixes: d6786fefe8 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remvoe the deprecated "supports-highspeed" property.
DWMMC controller will not use this property anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
msize and rx_wmark are properly initialized, we dont't
need to assign them again.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's very prone to make mistake as we might forget
to replace all PAGE_SIZEs with new values if we try
to modify the ring buffer size for whatever reasons.
Let's use a macro to define it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The original log didn't figure out that we could still
finish this transfer by PIO mode even if failing to use
DMA. And it should be kept for debug level instead of
error one.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We could see an obvious race condition by test that
the former write operation by IDMAC aiming to clear
OWN bit reach right after the later configuration of
the same desc, which makes the IDMAC be in SUSPEND
state as the OWN bit was cleared by the asynchronous
write operation of IDMAC. The bug can be very easy
reproduced on RK3288 or similar when we reduce the
running rate of system buses and keep the CPU running
faster. So as two separate masters, IDMAC and cpu
write the same descriptor stored on the same address,
and this should be protected by adding check of OWN
bit before preparing new descriptors.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We intend to add more check for descriptors when
preparing desc. Let's spilt out the separate body
to make the dw_mci_translate_sglist not so lengthy.
After spliting out these two functions, we could
remove dw_mci_translate_sglist and call both of them
when staring idmac.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following log we found indicate the fact that dw_mmc
didn't treat EBE or SBE as a similar problem as CRC error.
-EIO is quite not informative as it may indicate that the device
is broken rather than that of tuning stuff.
...
[ 89.057226] bcmsdh_sdmmc: Failed to Read byte F1:@0x1001f=ff, Err: -5
[ 89.058811] bcmsdh_sdmmc: Failed to Read byte F1:@0x1001f=ff, Err: -5
[ 89.059415] bcmsdh_sdmmc: Failed to Read byte F1:@0x1000e=ff, Err: -84
[ 89.254248] dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 199
[ 89.273912] dhd_set_suspend: Remove extra suspend setting
[ 89.274478] dhd_enable_packet_filter: enter, value = 0
64 bytes from 112.90.83.112: icmp_seq=24 ttl=53 time=1321 ms
64 bytes from 112.90.83.112: icmp_seq=25 ttl=53 time=319 ms
64 bytes from 112.90.83.112: icmp_seq=26 ttl=53 time=69.8 ms
64 bytes from 112.90.83.112: icmp_seq=27 ttl=53 time=37.5 ms
...
For the host, when failing to sample cmd's response due to
tuning stuff, we still return -EIO as it's quite vague to figure
out whether it related to signal or just the broken devices, especially
for the card type detection when booting kernel as all things go well
but the cmd set used.
But for the data phase, if receiving the cmd's response which
carriess data transfer, we should have more confidence that it
is very probably related to the tuning stuff.
Just as the log shown above, we sometimes suffer too much
this kind of pain as the dw_mmc return -EIO for the case, so
mmc-core will not do retune and caller drivers like bcm's wifi
driver, still retry the failure more and more until dw_mmc
finally generate CRC.
Adrian suggested that drivers who care the specific cases should
call mmc_retune_needed rather than doing it in mmc core. It makes
sense but I'm considering that -EILSEQ actually means illegal sequence
, so we use it for CRC cases. Meanwhile, SBE/EBE indicate the illegal
sequence of start bit or end bit for data0~7. So I realize that we should
use -EILSEQ for them both as well CRC cases.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dwmmc host controller may in unknown state when entering kernel boot. One
example is when booting from eMMC, bootloader need initialize MMC host
controller into some state so it can read. In order to make sure MMC host
controller in a clean initial state, this reset support is added.
With this patch, a 'resets' property can be added into dw_mmc device
tree node. The hardware logic is: dwmmc host controller IP receives a reset
signal from a 'reset provider' (eg. power management unit). The 'resets'
property points to this reset signal. So, during dwmmc driver probe,
it can use this signal to reset itself.
Refer to [1] for more information.
[1] Documentation/devicetree/bindings/reset/reset.txt
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If ciu/biu clock are NULL, clk_disable_unprepare should be just
returned. In clk_disable_unprepare(), already checked whether clk is
error or NULL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention to remove it comes from the conflict of
what the mmc-core does with the way dw_mmc treats disable-wp.
We could see that 'disable-wp' is supported by core but
it's deprecated by dw_mmc as we don't expect it to be existed
for each slot subnode but should be in the parent node. Based
on searching for all the upstream dts using dw_mmc, we're
confident that none of them use the deprecated way. Maybe
we should take old dtb in consideration but it was a flag day
since the time we was considering to take it away. The fact is
that there are none of dts using the deprecated way since v3.18
or even earlier. So personally I don't believe the old dtb
would/could bootup current kernel(may not?). Let's remove it now.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When there is no Card which is set to "broken-cd", it's displayed a clock
information continuously. Because it's polling for detecting card.
This patch is fixed this problem.
Fixes: 65257a0dee ("mmc: dw_mmc: remove UBSAN warning in dw_mci_setup_bus()")
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This flag needs to use the trim/discard/erase commands.
dwmmc controller enables this flag by default.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DATA_OVER(the same for RI/TI of IDMAC) interrupt may come
up together with data error interrupts. If so, the interrupt
routine set EVENT_DATA_ERR to the pending_events and schedule
the tasklet but we may still fallback to the IDMAC interrupt
case as the tasklet may come up a little late, namely right
after the IDMAC interrupt checking. This will casue dw_mmc
unmap sg twice. We can easily see it with CONFIG_DMA_API_DEBUG
enabled.
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1096 check_unmap+0x7bc/0xb38
dwmmc_exynos 12200000.mmc: DMA-API: device driver tries to free DMA memory it
has not allocated [device address=0x000000006d9d2200]
[size=128 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.7.0-rc4 #26
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0112b4c>] (unwind_backtrace) from [<c010d888>] (show_stack+0x20/0x24)
[<c010d888>] (show_stack) from [<c03fab0c>] (dump_stack+0x80/0x94)
[<c03fab0c>] (dump_stack) from [<c0123548>] (__warn+0xf8/0x110)
[<c0123548>] (__warn) from [<c01235a8>] (warn_slowpath_fmt+0x48/0x50)
[<c01235a8>] (warn_slowpath_fmt) from [<c042ac90>] (check_unmap+0x7bc/0xb38)
[<c042ac90>] (check_unmap) from [<c042b25c>] (debug_dma_unmap_sg+0x118/0x148)
[<c042b25c>] (debug_dma_unmap_sg) from [<c077512c>] (dw_mci_dma_cleanup+0x7c/0xb8)
[<c077512c>] (dw_mci_dma_cleanup) from [<c0773f24>] (dw_mci_stop_dma+0x40/0x50)
[<c0773f24>] (dw_mci_stop_dma) from [<c0777d04>] (dw_mci_tasklet_func+0x130/0x3b4)
[<c0777d04>] (dw_mci_tasklet_func) from [<c0129760>] (tasklet_action+0xb4/0x150)
..[snip]..
---[ end trace 256f83eed365daf0 ]---
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since v2.80a, dwmmc controller introduced the card write threshold for
HS400 mode. So CardThrCtl can be supported during write operation, not
only read operation.
(Note: Only use the write threshold when mode is HS400.)
To use more compatible, removed "_rd_" from function name.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the quirks flag. (DW_MCI_QUIRK_BROKEN_DTO)
For removing this, enabled the dto_timer by defaults.
It doesn't see any I/O performance degression.
In future, dwmmc controller should not use the quirks flag.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes following UBSAN warnings in dw_mci_setup_bus().
UBSAN: Undefined behaviour in drivers/mmc/host/dw_mmc.c:1102:14
shift exponent 250 is too large for 32-bit type 'unsigned int'
Call trace:
[<ffffff90080908a8>] dump_backtrace+0x0/0x380
[<ffffff9008090c3c>] show_stack+0x14/0x20
[<ffffff90087457b8>] dump_stack+0xe0/0x120
[<ffffff90087b1360>] ubsan_epilogue+0x18/0x68
[<ffffff90087b1a94>] __ubsan_handle_shift_out_of_bounds+0x18c/0x1bc
[<ffffff9008d89cb8>] dw_mci_setup_bus+0x3a0/0x438
[...]
UBSAN: Undefined behaviour in drivers/mmc/host/dw_mmc.c:1132:27
shift exponent 250 is too large for 32-bit type 'unsigned int'
Call trace:
[<ffffff90080908a8>] dump_backtrace+0x0/0x380
[<ffffff9008090c3c>] show_stack+0x14/0x20
[<ffffff90087457b8>] dump_stack+0xe0/0x120
[<ffffff90087b1360>] ubsan_epilogue+0x18/0x68
[<ffffff90087b1a94>] __ubsan_handle_shift_out_of_bounds+0x18c/0x1bc
[<ffffff9008d89c9c>] dw_mci_setup_bus+0x384/0x438
[...]
The warnings are caused because of bit shift which is used to
filter spamming message for CONFIG_MMC_CLKGATE, but the config is
already removed. So this patch just removes the shift.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the DesignWare state machine description, after we get a
"response error" or "response CRC error" we move into data transfer
mode. That means that we don't necessarily need to special case
trying to deal with the failure right away. We can wait until we are
notified that the data transfer is complete (with or without errors)
and then we can deal with the failure.
It may sound strange to defer dealing with a command that we know will
fail anyway, but this appears to fix a bug. During tuning (CMD19) on
a specific card on an rk3288-based system, we found that we could get
a "response CRC error". Sending the stop command after the "response
CRC error" would then throw the system into a confused state causing
all future tuning phases to report failure.
When in the confused state, the controller would show these (hex codes
are interrupt status register):
CMD ERR: 0x00000046 (cmd=19)
CMD ERR: 0x0000004e (cmd=12)
DATA ERR: 0x00000208
DATA ERR: 0x0000020c
CMD ERR: 0x00000104 (cmd=19)
CMD ERR: 0x00000104 (cmd=12)
DATA ERR: 0x00000208
DATA ERR: 0x0000020c
...
...
It is inherently difficult to deal with the complexity of trying to
correctly send a stop command while a data transfer is taking place
since you need to deal with different corner cases caused by the fact
that the data transfer could complete (with errors or without errors)
during various places in sending the stop command (dw_mci_stop_dma,
send_stop_abort, etc)
Instead of adding a bunch of extra complexity to deal with this, it
seems much simpler to just use the more straightforward (and less
error-prone) path of letting the data transfer finish. There
shouldn't be any huge benefit to sending the stop command slightly
earlier, anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Alim Akhtar <alim.akhtar@gmail.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The IDMAC_SET_BUFFER1_SIZE() macro modifies des1, but does
not check if the value being passed is big or little endian
desptire the des1 field being marked as __le32.
Fix the issue by ensuring the values are changed from the
cpu endian to the descriptor endian by using cpu_to_le32.
Spotted whilst doing big endian conversion work on Exynos,
and stops the mmc worker thread from stalling.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver enables HLE errors as part of DW_MCI_ERROR_FLAGS but
nothing in the interrupt handler actually handles them and ACKs them.
That means that if we ever get an HLE error we'll just keep getting
interrupts and we'll wedge things.
We really don't expect HLE errors but if we ever get them we shouldn't
silently ignore them.
Note that I have seen HLE errors while constantly ejecting and
inserting cards (ejecting while inserting, etc).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The main reason to add this check is to avoid unnecessary
mmc_request like the on-going cmd and the corresponding sbc
if the card is removed. Although we have already checked this in
dw_mci_handle_cd for runtime usage of sd card and dw_mci_init_slot
for noremovable devices, but there is a timing gap before it really
calls dw_mci_get_cd as mmc_detect_change needs some delay here.
Another gain here is that we could save some checkings of card status
after sd card been removed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_get_cd have already dealt with these for
both of internal card-detect and gpio card-detect.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In linux/mmc/host.h, mmc_card_is_removable() is already defined.
It should be maintainted more easier than now.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to DesignWare TRM, BLKSIZ is 16bits.
Then it's correct that max_blk_size should be 0xFFFF, not 0x10000.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, no dw_mmc variant drivers use this callback, let's
remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine_terminate_all is deprecated and should be
replaced by more explicit synchronous and asynchronous
terminate functions. This change is based on the
commit b36f09c3c4 ("dmaengine: Add transfer termination
synchronization support"). Currently dw_mci_stop_dma
may be called under the spinlock, let's migrate
dmaengine_terminate_all to async terminate. This could
avoid the race condition of use-after-free resouce of
dmaengine once slave-dma driver implement the synchronize
method.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch make num_slots to 1 if pdata->num_slot is not
defined. Meanwhile, we need to make sure num_slots should
not larger that the supported slots
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_probe clear interrupts and disable all interrupts firstly.
While it clear interrupt again before enable some interrupts. We
can't see any reason to clear it twice here, so remove the second one.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mmc already use mmc_of_parse to get "broken-cd" property,
but it considered "broken-cd" to be a quirk in its driver. We
don't need this quirk here, and just take what we need from
mmc->caps.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch implement hw_reset function for DesignWare
MMC controller. By adding this feature, mmc blk can
do some basic recovery.
Set the following resets:
software reset – BMOD[0] for IDMAC only
DMA reset - CTRL[2]
FIFO reset - CTRL[1] bits
Program the CARD_RESET register with a value of 0 for the bit
corresponding to the card number; This programming asserts the
RST_n signal and resets the card. After a minimum of 1 ?s, de-asserts the
RST_n signal and takes the card out of reset. The application can program
a new CMD only after a minimum of 200 us
This implementation can be easily tested by cutting off->On vmmc
while doing data accessing in background to simulate that case.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes the prepare_command hook from entire dw_mmc driver.
Now, almost all SoCs are using by default, except Exynos.
It seems that dwmmc controller is using unnecessary hook.
To know whether needs to set this bit or not,
add the DW_MMC_CARD_NO_USE_HOLD bit.
If some SoCs need to disable this in future, just set the
DW_MMC_CARD_NO_USE_HOLD bit.
set_bit(DW_MMC_CARD_NO_USE_HOLD, &slot->flags),
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver stores the physical address of the MMIO registers
in a pointer, which requires the use of type casts, and is actually
broken if anyone ever has this device on a 32-bit SoC in registers
above 4GB. Gcc warns about this possibility when the driver is built
with ARM LPAE enabled:
mmc/host/dw_mmc.c: In function 'dw_mci_edmac_start_dma':
mmc/host/dw_mmc.c:702:17: warning: cast from pointer to integer of different size
cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
^
mmc/host/dw_mmc-pltfm.c: In function 'dw_mci_pltfm_register':
mmc/host/dw_mmc-pltfm.c:63:19: warning: cast to pointer from integer of different size
host->phy_regs = (void *)(regs->start);
This changes the code to use resource_size_t, which gets rid of the
warning, the bug and the useless casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When card is running with DDR mode, dwmmc needs to set DDR_REG bit at
UHS_REG register.
Before this patch, dwmmc controller doesn't consider this.
If this patch is not applied, CRC or other error shoulds be occurred.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "host->dms->ch" pointer is NULL here so we can't use it to print the
error message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add some macros for HCON register operations
to make code more readable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK31xx
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
