Fix tg3_set_power_state to drive GPIOs properly based on the
TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0
and D3 power state changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup proper GPIO settings in tp->grc_local_ctrl before calling
tg3_set_power() state in tg3_get_invariants() and after chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so
that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling
tg3_set_power_state() in tg3_get_invariants(). This will allow
tg3_set_power_state() to drive the GPIOs correctly based on the config.
information in eeprom.
On the 5752, there are no pull-up resistors on the GPIO pins and it is
necessary to drive the unused GPIOs as output.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor 5752 fixes mostly for correctness and add 5752 PHY ID.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0,
and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1
to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use check of TG3_FLG2_5750_PLUS in tg3_get_invariants to set
TG3_FLG2_5705_PLUS flag.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrite checks in tg3_get_invariants to use TG3_FLG2_5705_PLUS and
TG3_FLG2_5750_PLUS flags.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrite of a couple of troublesome multi-way if statements to use
TG3_FLG2_5705_PLUS flag.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a number of two-way if statements checking for 5750, and/or
5752 to reference the newly-defined TG3_FLG2_5750_PLUS flag instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for
ASIC_REV_5750 or ASIC_REV_5752.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a number of three-way if statements checking for 5705, 5750,
and 5752 to reference the equivalent TG3_FLG2_5705_PLUS flag instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3.
I did this separately in case patches like this (i.e. new PCI IDs)
need to come from more "official" sources.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hard-coded definition of bcm5752 PCI ID to tg3_pci_tbl.
Next patch will change entry to use pci_ids.h-based definition.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ASIC_REV_5752 definition.
Track-down all references to ASIC_REV_5750 and mirror them with
references to the newly defined ASIC_REV_5752.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix non-legacy multichannel ISO receive, broken by Parag Wardukar's
allocation fix. Multichannel ISO receive still sucks; it should be possible
to use both legacy and non-legacy modes at the same time, but with this
patch, things are no worse than they were in 2.6.11 and allocation is
still done at the correct time.
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Print the correct value in the DBGMSG in dma_rcv_tasklet().
See OHCI 1.1 section 8.7, page 103 ff.
- Print tlabels as %d everywhere.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We do not longer use DLT_LINUX_SLL for activ/pass filters but
DLT_PPP_WITHDIRECTION witch need 1 as outbound flag.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My version of gcc doesn't warn about this error (declaration in the
middle of a set of statements).
The fix is simple (this also corrects return code; for init functions it
should be zero or error).
I can't use list.h, since sk_buff doesn't have a list_head but instead
has two struct sk_buff pointers, and I want to avoid any extra memory
allocation.
send outgoing packets in order
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_add() and kobject_del() don't emit hotplug events anymore.
We need to do it ourselves now.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_add() and kobject_del() don't emit hotplug events anymore. Do it
ourselves if we are finished populating the device directory.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_add() and kobject_del() don't emit hotplug events anymore. Do it
ourselves if we are finished populating the device directory.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
platform_add_devices can be used from within modules, so it should be
exported. This can for example happen if you have hotpluggable firmware in
an FPGA on a system on chip processor; in our case the FPGA is probed for
devices and the FPGA base code registers the devices it has found with the
kernel.
(akpm: I think this is reasonable from a licensing POV: it's unlikely that
anyone would be interested in merging such specialised modules into mainline,
and it's a GPL export).
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Tue, 2005-03-15 at 09:25 +0100, Hannes Reinecke wrote:
> The current implementation of the firmware class breaks a fundamental
> assumption in udevd: that the physical device can be initialised fully
> prior to executing the next event for that device.
Here we add a TIMEOUT value to the hotplug environment of the firmware
requesting event. I will adapt udevd not to wait for anything else, if
it finds a TIMEOUT key.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The it87 and via686a hardware monitoring drivers each create a sysfs
file named "alarms" in R/W mode, while they should really create it in
read-only mode. Since we don't provide a store function for these files,
write attempts to these files will do something undefined (I guess) and
bad (I am sure). My own try resulted in a locked terminal (where I
attempted the write) and a 100% CPU load until next reboot.
As a side note, wouldn't it make sense to check, when creating sysfs
files, that readable files have a non-NULL show method, and writable
files have a non-NULL store method? I know drivers are not supposed to
do stupid things, but there is already a BUG_ON for several conditions
in sysfs_create_file, so maybe we could add two more?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here comes a small cleanup patch for the via686a driver. I noticed the
following two non-fatal problems:
1* The device parent is explicitely set, but it's not needed because the
i2c core will do as the client is registered.
2* snprintf is used where strlcpy would suffice.
Fixing them brings the via686a driver in line with what other similar
drivers do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Real fix for big endian machines - crc must be calculated
using little endian byte order.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updates to the Ethernet/RNDIS gadget driver (mostly for RNDIS):
- Fix brown-paper bag goof with RNDIS packet TX ... the wrong length
field got set, so Windows would ignore data packets it received.
- More consistent handling of CDC output filters (but not yet hooking
things up so RNDIS uses the mechanism).
- Zerocopy RX for RNDIS packets too (saving CPU cycles).
- Use the pre-allocated interrupt/status request and buffer, rather
than allocating and freeing one of each every few seconds (which
could fail).
- Some more "sparse" tweaks, making both dual-speed and single-speed
configurations happier.
- RNDIS speeds are reported in units of 100bps, not bps.
Plus two minor cleanups (whitespace, messaging).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of a bunch of redundant NULL pointer checks in drivers/usb/*,
there's no need to check a pointer for NULL before calling kfree() on it.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/class/audio.c
===================================================================
Checking for NULL before calling kfree() is redundant. This patch removes
these redundant checks and also makes a few tiny whitespace changes.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please accept the attached patch which adds the vendorid 0x0745 and
modelid 0x0001 (ID 0745:0001) "Syntech Information Co., Ltd."
The device is an USB IR cradle for a barcode scanner (CPT-8001C) from
Cipherlab.
From: Peter Favrholdt <pfavr@mip.sdu.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -u kernel-source-2.6.11/drivers/usb/serial/pl2303.c ../kernel-source-2.6.11/drivers/usb/serial/pl2303.c
I'm attaching a patch to fix status when using Siemens X65
mobile. This mobile use first byte instead of normal UART_STATE
byte.
From: Flavio Leitner <fbl@conectiva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/serial/pl2303.c
===================================================================
It's possible to unplug usb device and do tiocmset() and tiocmget() without
valid interface in pl2303 module.
The patch below check this and return -ENODEV if interface was removed.
From: Flavio Leitner <fbl@conectiva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -purN linux-05-04-11/drivers/usb/serial/pl2303.c linux-05-04-11.usb/drivers/usb/serial/pl2303.c
In response to complaints about excessive latency in the uhci-hcd driver
I'm planning to convert it to a top-half/bottom-half design. It turns out
that to do this, the USB API has to be modified slightly since the driver
will not be able to meet one of the guarantees in the current API. This
patch changes some kerneldoc, specifying the weaker guarantee.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a quirk to the OHCI driver that lets it work with an old
Compaq implementation. It also removes some needless strings from
the non-debug version of the driver.
Signed-off-by: Chris Clayton <chris_clayton@f1internet.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hmm, another case of a Zaurus ROM not telling the expected conformance lie;
this patch handles the lies told by the SL5600.
From: bender647@gmail.com
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the attached patch adds another USB device ID to the list. Seems the
device is known under multiple IDs.
Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Chan