[ Upstream commit 94dad6bed3 ]
For UARTs, the local pull-ups should be on the RX pin, not the TX pin.
UARTs transmit active-low, so a disconnected RX pin should be pulled
high instead of left floating to prevent noise being interpreted as
transmissions.
This gets rid of bogus sysrq events when the UART console is not
connected.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201204064805.6480-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
150MHz is a fundamental limitation of RK3328 Soc, w/o this limitation,
eMMC, for instance, will run into 200MHz clock rate in HS200 mode, which
makes the RK3328 boards not always boot properly. By adding it in
rk3328.dtsi would also obviate the worry of missing it when adding new
boards.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Cc: stable@vger.kernel.org
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Liang Chen <cl@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the missing clock property for the watchdog on rk3328.
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
[set wdt node to always enabled, as it is not board-specific]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds #sound-dai-cells to use HDMI node as audio
codec from device tree of rk3328 boards.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch enables HDMI CEC on RK3328 devices.
(Unusual) source for the cec clock is taken from the vendor kernel.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Various rk3328 based boards experience occasional sdmmc0 write errors.
This is due to the rk3328.dtsi tx drive levels being set to 4ma, vs
8ma per the rk3328 datasheet default settings.
Fix this by setting the tx signal pins to 8ma.
Inspiration from tonymac32's patch,
dc1212b347
Fixes issues on the rk3328-roc-cc and the rk3328-rock64 (as per the
above commit message).
Tested on the rk3328-roc-cc board.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Several rk3328 based boards experience high rgmii tx error rates.
This is due to several pins in the rk3328.dtsi rgmii pinmux that are
missing a defined pull strength setting.
This causes the pinmux driver to default to 2ma (bit mask 00).
These pins are only defined in the rk3328.dtsi, and are not listed in
the rk3328 specification.
The TRM only lists them as "Reserved"
(RK3328 TRM V1.1, 3.3.3 Detail Register Description, GRF_GPIO0B_IOMUX,
GRF_GPIO0C_IOMUX, GRF_GPIO0D_IOMUX).
However, removal of these pins from the rgmii pinmux definition causes
the interface to fail to transmit.
Also, the rgmii tx and rx pins defined in the dtsi are not consistent
with the rk3328 specification, with tx pins currently set to 12ma and
rx pins set to 2ma.
Fix this by setting tx pins to 8ma and the rx pins to 4ma, consistent
with the specification.
Defining the drive strength for the undefined pins eliminated the high
tx packet error rate observed under heavy data transfers.
Aligning the drive strength to the TRM values eliminated the occasional
packet retry errors under iperf3 testing.
This allows much higher data rates with no recorded tx errors.
Tested on the rk3328-roc-cc board.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
two being part of a family and sharing bigger parts of the devicetree.
rk3328 got sound-related upgrades and a wider patch drops mmc display-wp
fields from nodes which shouldn't use it.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlxTAa0QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgYrMB/93qkhsRz6kGXyeGWLQFYVJZET1IsHIqRUl
HDu/NwvZRPheupjgk37lAbTvQ8TeE8zb8i5I3lbhSZr1m8GL1Bsc3XZc2l8FXA9f
jib3xCaykp/qZMjgqSsesZmwcMzpUdMuGvK4NLLIWNWW+u3jQzo8N4eyXexRzY29
4Z69GodfMbsvFfi9mJ63pb2iTJhU+h1pLm4X8Df5DE4i1QyL9+vOiVYFM7AaMhMC
bBHzkQiJZC5hlhKUcCCW22T62yPnCHQdRG7SNPVyh/zSl3GvtL1CP9CHFDsPHG/j
443k+McXCvRCSK1wjRJraffD8gluBa/QgjFZj7hvuooOX7aGlM2E
=Bc63
-----END PGP SIGNATURE-----
Merge tag 'v5.1-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New boards are the Rock Pi 4, NanoPC-T4 and NanoPi-M4, with the last
two being part of a family and sharing bigger parts of the devicetree.
rk3328 got sound-related upgrades and a wider patch drops mmc display-wp
fields from nodes which shouldn't use it.
* tag 'v5.1-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: clean up the abuse of disable-wp
arm64: dts: rockchip: 'Fix' nanopi4 uSD card detect
arm64: dts: rockchip: Add NanoPC-T4 IR receiver
arm64: dts: rockchip: Refine nanopi4 differences
arm64: dts: rockchip: Add DT for NanoPi M4
arm64: dts: rockchip: add ROCK Pi 4 DTS support
arm64: dts: rockchip: Add devicetree for NanoPC-T4
arm64: dts: rockchip: enable analog audio node for rock64
arm64: dts: rockchip: move rk3328 #sound-dai-cells to the soc dtsi
arm64: dts: rockchip: add rk3328 ACODEC node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The rk3328 i2s and spdif controllers only ever have one output
connection, so as with all implementations of the rk3066 i2s
controllers we can keep the #sound-dai-cells in the main dtsi
instead of having it repeated in each board.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds audio codec (ACODEC) node that converts to analog
audio signal from I2S for rk3328.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the chain of display nodes from the core display-subsystem
through the one vop to the dw-hdmi output.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
changes in v3:
- drop reg from hdmi-in-port
changes in v2:
- remove trailing 0 from vop irq
The rk3328 uses a hdmiphy from Innosilicon, so add the necessary node
to the rk3328 soc devicetree.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Adding a GRF GPIO controller labled "grf_gpio" to rk3328, currently
providing access to the GPIO_MUTE pin, which is manupulated by the
GRF_SOC_CON10 register.
The GPIO_MUTE pin is referred to as <&grf_gpio 0>.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
[dropped default-status disabled]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Do minor rearrangement as well to keep ordering consistent.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Update all 64bit rockchip devicetree files to use SPDX-License-Identifiers.
All devicetrees claim to be either GPL or X11 while the actual license
text is MIT. Therefore we use MIT for the SPDX tag as X11 is clearly
wrong.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add clocks in iommu nodes, since we are going to control clocks in
rockchip iommu driver.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
minor additions like pins for 2ch i2s0 and the cif test clocks as well
as a default rate for ACLK_VIO that should be 400MHz according to the TRM.
The rk3328 got uart dmas fixed - a non-critical fix, as nobody was using
that so far.
New boards are the rk3328-based roc-rk3328-cc, the rk3368-based Lion-SOM
+ baseborad from Theobroma Systems and a standalone variant of the Sapphire
board, as a lot of people where using that without the Exkavator baseboard.
Sapphire also saw a lot of small cleanups of things that are not part
of the actual Sapphire board, but the baseboard instead. The rk3399-puma
board got i2s and tsadc support and Gru got its DP node enabled.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqpTQoQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgZ0uCACl6GsROypjpCGLtCsxlaAXdjk0EuBI3rzy
wW2AkmeJQHvMPYIAodVUTqEJW7w2M4V0LbF1YOzebSyLMckejKy2jQGNcjQeQ//p
QAIilflqxqYHTzx9Abv1EpX9uYVsLA46TUnInHAlo+SyDcDAx5/D37oASS+EvlKS
AHniQE5XfH/zf/0ASRqyzKXI+rxhovinUCeVxsJmWS5+jUchUy/PTgx3OBnTahd+
JYjEOygTfPJoVXI3LBsQhuZdGZAVoCrDETsur8tMBBHwUHDQxy2rpLwzqv72C+SR
kdO93Xgjz1+mML3qivJPKYPlc4OabFKgP9BzMnBsALJPXykX7cQw
=Ay+8
-----END PGP SIGNATURE-----
Merge tag 'v4.17-rockchip-dts64-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts64 changes for 4.17" from Heiko Stübner:
The rk3399 gained support its Cadence displayport controller and some
minor additions like pins for 2ch i2s0 and the cif test clocks as well
as a default rate for ACLK_VIO that should be 400MHz according to the TRM.
The rk3328 got uart dmas fixed - a non-critical fix, as nobody was using
that so far.
New boards are the rk3328-based roc-rk3328-cc, the rk3368-based Lion-SOM
+ baseborad from Theobroma Systems and a standalone variant of the Sapphire
board, as a lot of people where using that without the Exkavator baseboard.
Sapphire also saw a lot of small cleanups of things that are not part
of the actual Sapphire board, but the baseboard instead. The rk3399-puma
board got i2s and tsadc support and Gru got its DP node enabled.
* tag 'v4.17-rockchip-dts64-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: remove keep-power-in-suspend from sdhci of rk3399-sapphire
arm64: dts: rockchip: assign clock rate for ACLK_VIO on rk3399
arm64: dts: rockchip: add a standalone version of the rk3399 sapphire
arm64: dts: rockchip: move rk3399-sapphire pwr_btn to daughterboard
arm64: dts: rockchip: move rk3399-sapphire i2s2 to daughterboard
arm64: dts: rockchip: move rk3399-sapphire sdio to excavator baseboard
arm64: dts: rockchip: enable I2S codec on rk3399-puma-haikou
arm64: dts: rockchip: move i2s0 node from baseboard to SoM on rk3399-puma
arm64: dts: rockchip: vdd_log on rk3399-sapphire is not an i2c slave
arm64: dts: rockchip: add Haikou baseboard with RK3368-uQ7 SoM
arm64: dts: rockchip: add RK3368-uQ7 (Lion) SoM
dt-bindings: add RK3368-uQ7 SoM and EVK base board
arm64: dts: rockchip: Fix RK3328 UART DMAs
arm64: dts: rockchip: enable DP for rk3399-gru
arm64: dts: rockchip: add cdn-dp node for rk3399.
arm64: dts: rockchip: add i2s0-2ch-bus pins on rk3399
arm64: dts: rockchip: enable tsadc on rk3399-puma
arm64: dts: rockchip: add roc-rk3328-cc board
arm64: dts: rockchip: Add cif test clocks for rk3399
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
Fix up all instances of the incorrect clock names across the 64-bit DTs.
Fixes: d717f7352e ("arm64: dts: rockchip: add sdmmc/sdio/emmc nodes for RK3328 SoCs")
Fixes: b790c2cab5 ("arm64: dts: add Rockchip rk3368 core dtsi and board dts for the r88 board")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Using a serial console on RK3328 provokes an error from
of_dma_request_slave_channel() since the UART nodes have a "dmas"
property but are missing the mandatory "dma-names" to go with it.
Replace the bogus "#dma-cells" - these UARTs are DMA channel consumers,
not providers - with the appropriate names instead. DMA still doesn't
actually work, since the PL330 driver doesn't quite implement everything
the 8250 driver demands, but at least it makes the DT correct.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We get a moderate number of new machines this time, and only one
new SoC variant (Actions S700):
Actions:
S700 Soc and CubieBoard7 development board
Allo.com Sparky Single-board-computer
Allwinner:
Orange Pi R1 development board
Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
Axentia Nattis/Natte digital signage
sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
SolidRun Humminboard2 development board
Variscite DART-MX6 SoM and Carrier-board
Technologic TS-4600 and TS-7970 development board
Toradex Colibri iMX7D SoM board
v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
Moxa UC-8410A Series industrial computer
Gemini:
D-Link DNS-313 NAS enclosure
OMAP:
LogicPD OMAP35xx SOM-LV devkit
LogicPD OMAP35xx Torpedo devkit
Renesas:
r8a77970 (V3M) Starter Kit board
r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
Aspeed clk controller support
Freescale LS1088A, LS1021A device support
Gemini Ethernet, PCI, TVE, panel
Keystone gpio, qspi, more uarts
Mediatek cpufreq, regulator, clock, reset
Marvell thermal, cpufreq, nand
Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
Rockchip Mipi, GPU, display
Samsung Exynos5433 PMU, power domain, nfc
Spreadtrum: sc9860 clocks
Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qN1F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
This patch adds an efuse node in the device tree for rk3228 SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Probably due to some copy-paste mistake, the tsadc of rk3328 ended up
with a 0 as 4th element that shouldn't be there, as interrupts on the
rk3328 only have multiples of 3, making dtc complain. So remove it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The latest dtc warns about an extraneous cell in the interrupt
property of two of the iommu device nodes:
Warning (interrupts_property): interrupts size is (16), expected multiple of 12 in /iommu@ff373f00
Warning (interrupts_property): interrupts size is (16), expected multiple of 12 in /iommu@ff900800
This removes the typo.
Fixes: cede4c79de ("arm64: dts: rockchip: add rk3368 iommu nodes")
Fixes: 49c82f2b7c ("arm64: dts: rockchip: add rk3328 iommu nodes")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
There are 4 pwm channels built in rk3328 soc, need to configure
the both APB clock and bus clock.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The gmac2phy controller of rk3328 is connected to integrated PHY
directly inside, add the node for the integrated PHY support.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add thermal zone and dynamic CPU power coefficients for rk3328
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add tsadc needed main information for rk3328 SoC.
50000Hz is the max clock rate supported by tsadc module.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the core grf subnode for the io-domain controller.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Chen-Yu Tsai