Add back 82580 loopback tests to ethtool.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
clockevents_config_and_register is more clever and correct than doing it
by hand; so use it.
[vgupta: fixed build failure due to missing ; in patch]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Some ARC SMP systems lack native atomic R-M-W (LLOCK/SCOND) insns and
can only use atomic EX insn (reg with mem) to build higher level R-M-W
primitives. This includes a SystemC based SMP simulation model.
So rwlocks need to use a protecting spinlock for atomic cmp-n-exchange
operation to update reader(s)/writer count.
The spinlock operation itself looks as follows:
mov reg, 1 ; 1=locked, 0=unlocked
retry:
EX reg, [lock] ; load existing, store 1, atomically
BREQ reg, 1, rety ; if already locked, retry
In single-threaded simulation, SystemC alternates between the 2 cores
with "N" insn each based scheduling. Additionally for insn with global
side effect, such as EX writing to shared mem, a core switch is
enforced too.
Given that, 2 cores doing a repeated EX on same location, Linux often
got into a livelock e.g. when both cores were fiddling with tasklist
lock (gdbserver / hackbench) for read/write respectively as the
sequence diagram below shows:
core1 core2
-------- --------
1. spin lock [EX r=0, w=1] - LOCKED
2. rwlock(Read) - LOCKED
3. spin unlock [ST 0] - UNLOCKED
spin lock [EX r=0,w=1] - LOCKED
-- resched core 1----
5. spin lock [EX r=1] - ALREADY-LOCKED
-- resched core 2----
6. rwlock(Write) - READER-LOCKED
7. spin unlock [ST 0]
8. rwlock failed, retry again
9. spin lock [EX r=0, w=1]
-- resched core 1----
10 spinlock locked in #9, retry #5
11. spin lock [EX gets 1]
-- resched core 2----
...
...
The fix was to unlock using the EX insn too (step 7), to trigger another
SystemC scheduling pass which would let core1 proceed, eliding the
livelock.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Anton reported
| LTP tests syscalls/process_vm_readv01 and process_vm_writev01 fail
| similarly in one testcase test_iov_invalid -> lvec->iov_base.
| Testcase expects errno EFAULT and return code -1,
| but it gets return code 1 and ERRNO is 0 what means success.
Essentially test case was passing a pointer of -1 which access_ok()
was not catching. It was doing [@addr + @sz <= TASK_SIZE] which would
pass for @addr == -1
Fixed that by rewriting as [@addr <= TASK_SIZE - @sz]
Reported-by: Anton Kolesov <Anton.Kolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
If a load or store is the last instruction in a zero-overhead-loop, and
it's misaligned, the loop would execute only once.
This fixes that problem.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This patch adds the default pin configuration and some init verbs for
setting COEFs, in addition to the correction of input pin AMP caps
for MacBook Air 6,1 and 6,2. With these changes, the headphone jack
detection starts working properly.
[trivial space fixes by tiwai]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Signed-off-by: Ben Whitten <benwhitten@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On AMD family 14h, applying microcode patch on the a core (core0)
would also affect the other core (core1) in the same compute
unit. The driver would skip applying the patch on core1, but it
still need to update kernel structures to reflect the proper
patch level.
The current logic is not updating the struct
ucode_cpu_info.cpu_sig.rev of the skipped core. This causes the
/sys/devices/system/cpu/cpu1/microcode/version to report
incorrect patch level as shown below:
$ grep . cpu?/microcode/version
cpu0/microcode/version:0x600063d
cpu1/microcode/version:0x6000626
cpu2/microcode/version:0x600063d
cpu3/microcode/version:0x6000626
cpu4/microcode/version:0x600063d
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: <bp@alien8.de>
Cc: <jacob.w.shin@gmail.com>
Cc: <herrmann.der.user@googlemail.com>
Link: http://lkml.kernel.org/r/1285806432-1995-1-git-send-email-suravee.suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In case of usb phy reinitialization:
e.g. insmod usb-module(usb works well) -> rmmod usb-module -> insmod usb-module
It found the PHY_CLK_VALID bit didn't work if it's not with the power-on reset.
So we just check PHY_CLK_VALID bit during the stage with POR, this can be met
by the tricky of checking FSL_SOC_USB_PRICTRL register.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a bunch of failure exits in ffs_fs_mount() with
seriously broken recovery logics. Most of that appears to stem
from misunderstanding of the ->kill_sb() semantics; unlike
->put_super() it is called for *all* superblocks of given type,
no matter how (in)complete the setup had been. ->put_super()
is called only if ->s_root is not NULL; any failure prior to
setting ->s_root will have the call of ->put_super() skipped.
->kill_sb(), OTOH, awaits every superblock that has come from
sget().
Current behaviour of ffs_fs_mount():
We have struct ffs_sb_fill_data data on stack there. We do
ffs_dev = functionfs_acquire_dev_callback(dev_name);
and store that in data.private_data. Then we call mount_nodev(),
passing it ffs_sb_fill() as a callback. That will either fail
outright, or manage to call ffs_sb_fill(). There we allocate an
instance of struct ffs_data, slap the value of ffs_dev (picked
from data.private_data) into ffs->private_data and overwrite
data.private_data by storing ffs into an overlapping member
(data.ffs_data). Then we store ffs into sb->s_fs_info and attempt
to set the rest of the things up (root inode, root dentry, then
create /ep0 there). Any of those might fail. Should that
happen, we get ffs_fs_kill_sb() called before mount_nodev()
returns. If mount_nodev() fails for any reason whatsoever,
we proceed to
functionfs_release_dev_callback(data.ffs_data);
That's broken in a lot of ways. Suppose the thing has failed in
allocation of e.g. root inode or dentry. We have
functionfs_release_dev_callback(ffs);
ffs_data_put(ffs);
done by ffs_fs_kill_sb() (ffs accessed via sb->s_fs_info), followed by
functionfs_release_dev_callback(ffs);
from ffs_fs_mount() (via data.ffs_data). Note that the second
functionfs_release_dev_callback() has every chance to be done to freed memory.
Suppose we fail *before* root inode allocation. What happens then?
ffs_fs_kill_sb() doesn't do anything to ffs (it's either not called at all,
or it doesn't have a pointer to ffs stored in sb->s_fs_info). And
functionfs_release_dev_callback(data.ffs_data);
is called by ffs_fs_mount(), but here we are in nasal daemon country - we
are reading from a member of union we'd never stored into. In practice,
we'll get what we used to store into the overlapping field, i.e. ffs_dev.
And then we get screwed, since we treat it (struct gfs_ffs_obj * in
disguise, returned by functionfs_acquire_dev_callback()) as struct
ffs_data *, pick what would've been ffs_data ->private_data from it
(*well* past the actual end of the struct gfs_ffs_obj - struct ffs_data
is much bigger) and poke in whatever it points to.
FWIW, there's a minor leak on top of all that in case if ffs_sb_fill()
fails on kstrdup() - ffs is obviously forgotten.
The thing is, there is no point in playing all those games with union.
Just allocate and initialize ffs_data *before* calling mount_nodev() and
pass a pointer to it via data.ffs_data. And once it's stored in
sb->s_fs_info, clear data.ffs_data, so that ffs_fs_mount() knows that
it doesn't need to kill the sucker manually - from that point on
we'll have it done by ->kill_sb().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: stable <stable@vger.kernel.org> # 3.3+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The put_device(dev) at the bottom of the loop of device_shutdown
may result in the dev being cleaned up. In device_create_release,
the dev is kfreed.
However, device_shutdown attempts to use the dev pointer again after
put_device by referring to dev->parent.
Copy the parent pointer instead to avoid this condition.
This bug was found on Chromium OS's chromeos-3.8, which is based on v3.8.11.
See bug report : https://code.google.com/p/chromium/issues/detail?id=297842
This can easily be reproduced when shutting down with
hidraw devices that report battery condition.
Two examples are the HP Bluetooth Mouse X4000b and the Apple Magic Mouse.
For example, with the magic mouse :
The dev in question is "hidraw0"
dev->parent is "magicmouse"
In the course of the shutdown for this device, the input event cleanup calls
a put on hidraw0, decrementing its reference count.
When we finally get to put_device(dev) in device_shutdown, kobject_cleanup
is called and device_create_release does kfree(dev).
dev->parent is no longer valid, and we may crash in
put_device(dev->parent).
This change should be applied on any kernel with this change :
d1c6c030fc
Cc: stable@vger.kernel.org
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In kobj_ns_current_may_mount the default should be to allow the
mount. The test is only for a single kobj_ns_type at a time, and unless
there is a reason to prevent it the mounting sysfs should be allowed.
Subsystems that are not registered can't have are not involved so can't
have a reason to prevent mounting sysfs.
This is a bug-fix to:
commit 7dc5dbc879
Author: Eric W. Biederman <ebiederm@xmission.com>
Date: Mon Mar 25 20:07:01 2013 -0700
sysfs: Restrict mounting sysfs
Don't allow mounting sysfs unless the caller has CAP_SYS_ADMIN rights
over the net namespace. The principle here is if you create or have
capabilities over it you can mount it, otherwise you get to live with
what other people have mounted.
Instead of testing this with a straight forward ns_capable call,
perform this check the long and torturous way with kobject helpers,
this keeps direct knowledge of namespaces out of sysfs, and preserves
the existing sysfs abstractions.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
That came in via the userns tree during the 3.12 merge window.
Reported-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 666b9adc80 terminated vmbus
version negotiation incorrectly. We need to terminate the version
negotiation only if the current negotiation were to timeout.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Olaf Hering <ohering@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code does not correctly negotiate the version numbers for the util
driver when hosted on earlier hosts. The version numbers presented by this
driver were not compatible with the version numbers supported by Windows Server
2008. Fix this problem.
I would like to thank Olaf Hering (ohering@suse.com) for identifying the problem.
Reported-by: Olaf Hering <ohering@suse.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unset init_clients_timer and amthif_stall_timers
in mei_reset in order to cancel timer ticking and hence
avoid recursive reset calls.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bus layer omitted check for client state transition while waiting
for read completion
The client state transition may occur for example as result
of firmware initiated reset
Add mei_cl_is_transitioning wrapper to reduce the code
repetition.:
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. u8 counters are prone to hard to detect overflow:
make them unsigned long to match bit_ functions argument type
2. don't check me_clients_num for negativity, it is unsigned.
3. init all the me client counters from one place
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Outgoing packets sent by via-rhine have their VLAN PCP field off by one
(when hardware acceleration is enabled). The TX descriptor expects only VID
and PCP (without a CFI/DEI bit).
Peter Boström noticed and reported the bug.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 'tty: ar933x_uart: add device tree support
and binding documentation' introduced a new doc in
bindins/tty/serial.
According to a recent thread [1] on the linux-serial
list, the binding documentation of serial drivers
should be added into bindings/serial.
Move the documentation of qca,ar9330-uart to the
correct place.
1. http://marc.info/?l=linux-serial&m=137771295411517
Cc: devicetree@vger.kernel.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For controller versions greater than 1.6, setting ULPI_PHY_CLK_SEL
bit when USB_EN bit is already set causes instability issues with
PHY_CLK_VLD bit. So USB_EN is set only for IP controller version
below 1.6 before setting ULPI_PHY_CLK_SEL bit
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My locking rework/race fixes caused a regression in the
registration, causing uevent notifications for wireless
devices before the device is really fully registered and
available in nl80211.
Fix this by moving the device_add() under rtnl and move
the rfkill to afterwards (it can't be under rtnl.)
Reported-and-tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver uses platform_driver_probe() to obtain platform data
if any. However, that function is placed in the .init section so
it must be called upon driver module initialization.
The problem was reported by Fenguang Wu resulting in a kernel
oops because the .init section was already freed.
[ 48.966342] Switched to clocksource tsc
[ 48.970002] kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
[ 48.970851] BUG: unable to handle kernel paging request at ffffffff82196446
[ 48.970957] IP: [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] PGD 1e76067 PUD 1e77063 PMD f388063 PTE 8000000002196163
[ 48.970957] Oops: 0011 [#1]
[ 48.970957] CPU: 0 PID: 17 Comm: kworker/0:1 Not tainted 3.11.0-rc7-00444-gc52dd7f #23
[ 48.970957] Workqueue: events brcmf_driver_init
[ 48.970957] task: ffff8800001d2000 ti: ffff8800001d4000 task.ti: ffff8800001d4000
[ 48.970957] RIP: 0010:[<ffffffff82196446>] [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] RSP: 0000:ffff8800001d5d40 EFLAGS: 00000286
[ 48.970957] RAX: 0000000000000001 RBX: ffffffff820c5620 RCX: 0000000000000000
[ 48.970957] RDX: 0000000000000001 RSI: ffffffff816f7380 RDI: ffffffff820c56c0
[ 48.970957] RBP: ffff8800001d5d50 R08: ffff8800001d2508 R09: 0000000000000002
[ 48.970957] R10: 0000000000000000 R11: 0001f7ce298c5620 R12: ffff8800001c76b0
[ 48.970957] R13: ffffffff81e91d40 R14: 0000000000000000 R15: ffff88000e0ce300
[ 48.970957] FS: 0000000000000000(0000) GS:ffffffff81e84000(0000) knlGS:0000000000000000
[ 48.970957] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 48.970957] CR2: ffffffff82196446 CR3: 0000000001e75000 CR4: 00000000000006b0
[ 48.970957] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 48.970957] DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
[ 48.970957] Stack:
[ 48.970957] ffffffff816f7df8 ffffffff820c5620 ffff8800001d5d60 ffffffff816eeec9
[ 48.970957] ffff8800001d5de0 ffffffff81073dc5 ffffffff81073d68 ffff8800001d5db8
[ 48.970957] 0000000000000086 ffffffff820c5620 ffffffff824f7fd0 0000000000000000
[ 48.970957] Call Trace:
[ 48.970957] [<ffffffff816f7df8>] ? brcmf_sdio_init+0x18/0x70
[ 48.970957] [<ffffffff816eeec9>] brcmf_driver_init+0x9/0x10
[ 48.970957] [<ffffffff81073dc5>] process_one_work+0x1d5/0x480
[ 48.970957] [<ffffffff81073d68>] ? process_one_work+0x178/0x480
[ 48.970957] [<ffffffff81074188>] worker_thread+0x118/0x3a0
[ 48.970957] [<ffffffff81074070>] ? process_one_work+0x480/0x480
[ 48.970957] [<ffffffff8107aa17>] kthread+0xe7/0xf0
[ 48.970957] [<ffffffff810829f7>] ? finish_task_switch.constprop.57+0x37/0xd0
[ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[ 48.970957] [<ffffffff81a6923a>] ret_from_fork+0x7a/0xb0
[ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[ 48.970957] Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
[ 48.970957] RIP [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] RSP <ffff8800001d5d40>
[ 48.970957] CR2: ffffffff82196446
[ 48.970957] ---[ end trace 62980817cd525f14 ]---
Cc: <stable@vger.kernel.org> # 3.10.x, 3.11.x
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815
[ 2.883807] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000048
[ 2.883813] IP: [<ffffffff815a65e0>] pfifo_fast_enqueue+0x90/0x90
[ 2.883834] CPU: 1 PID: 3220 Comm: kworker/u8:90 Not tainted
3.11.1-monotone-l0 #6
[ 2.883834] Hardware name: Microsoft Corporation Surface with
Windows 8 Pro/Surface with Windows 8 Pro,
BIOS 1.03.0450 03/29/2013
On Surface Pro, suspend to ram gives a NULL pointer dereference in
pfifo_fast_enqueue(). The stack trace reveals that the offending
call is clearing carrier in mwifiex_usb suspend handler.
Since commit 1499d9f "mwifiex: don't drop carrier flag over suspend"
has removed the carrier flag handling over suspend/resume in SDIO
and PCIe drivers, I'm removing it in USB driver too. This also fixes
the bug for Surface Pro.
Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815
We have 4 bytes of interface header for packets delivered to SDIO
and PCIe, but not for USB interface.
In Tx AMSDU case, currently 4 bytes of garbage data is unnecessarily
appended for USB packets. This sometimes leads to a firmware hang,
because it may not interpret the data packet correctly.
Problem is fixed by removing this redundant headroom for USB.
Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added USB ID for Corega WLUSB2GTST USB adapter.
Cc: <stable@vger.kernel.org>
Reported-by: Joerg Kalisch <the_force@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This supercedes the older patch ("cw1200: Don't perform SPI transfers in
interrupt context") that badly attempted to fix this problem.
This is a far simpler solution, which has the added benefit of
actually working.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit aec8e88c94.
This solution turned out to cause interrupt delivery problems, and
rather than trying to fix this approach, it has been scrapped in favor
of an alternative (and far simpler) implementation.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For pcie8897, the hs_cfg cancel command (0xe5) times out when host
comes out of suspend. This is caused by an incompleted host sleep
handshake between driver and firmware.
Like SDIO interface, PCIe also needs to go through firmware power
save events to complete the handshake for host sleep configuration.
Only USB interface doesn't require power save events for hs_cfg.
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The private array at the end of the rtl_priv struct is not aligned.
On ARM architecture, this causes an alignment trap and is fixed by aligning
that array with __align(sizeof(void *)). That should properly align that
space according to the requirements of all architectures.
Reported-by: Jason Andrews <jasona@cadence.com>
Tested-by: Jason Andrews <jasona@cadence.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevents race conditions when un-aggregated frames are pending in the
driver.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If request_firmware_nowait() fails in p54u_load_firmware(),
p54u_load_firmware_cb is not called and no one decrements usb_dev refcnt.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When .release_buffered_frames was implemented, only A-MPDU packets were
buffered internally. Now that this has changed, the BUF_AMPDU flag needs
to be checked before calling ath_tx_addto_baw
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Optimize LNA check" tried
to use the "rs_firstaggr" flag to optimize the LNA
combining algorithm when processing subframes in
an A-MPDU. This doesn't appear to work well in practice,
so revert it and use the old method of relying on
"rs_moreaggr".
Cc: stable@vger.kernel.org # 3.11
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This might trip up tx completion processing, although the condition that
triggers this should not (yet) occur in practice.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a regression from commit
"ath9k: shrink a few data structures by reordering fields"
When cloning a buffer, the stale flag (part of bf_state now) needs to be
reset after copying the state to prevent tx processing hangs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch "mac80211: select and adjust bitrates according to
channel mode" causes regression and breaks the extended supported rate
IE setting. Since "i" is starting with 8, so this is not necessary
to introduce "skip" here.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Reviewed-by: Jason Abele <jason@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an Ad-Hoc node receives packets with the Cell ID or its own MAC
address as source address, it hits a WARN_ON in sta_info_insert_check()
With many packets, this can massively spam the logs. One way that this
can easily happen is through having Cisco APs in the area with rouge AP
detection and countermeasures enabled.
Such Cisco APs will regularly send fake beacons, disassoc and deauth
packets that trigger these warnings.
To fix this issue, drop such spoofed packets early in the rx path.
Cc: stable@vger.kernel.org
Reported-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix kernel warning when using WEXT for configuring ad-hoc mode,
e.g. "iwconfig wlan0 essid test channel 1"
WARNING: at net/wireless/chan.c:373 cfg80211_chandef_usable+0x50/0x21c [cfg80211]()
The warning is caused by an uninitialized variable center_freq1.
Cc: stable@vger.kernel.org
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit f5ea1100 cleans up the disk to host conversions for
node directory entries, but because a variable is reused in
xfs_node_toosmall() the next node is not correctly found.
If the original node is small enough (<= 3/8 of the node size),
this change may incorrectly cause a node collapse when it should
not. That will cause an assert in xfstest generic/319:
Assertion failed: first <= last && last < BBTOB(bp->b_length),
file: /root/newest/xfs/fs/xfs/xfs_trans_buf.c, line: 569
Keep the original node header to get the correct forward node.
(When a node is considered for a merge with a sibling, it overwrites the
sibling pointers of the original incore nodehdr with the sibling's
pointers. This leads to loop considering the original node as a merge
candidate with itself in the second pass, and so it incorrectly
determines a merge should occur.)
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
[v3: added Dave Chinner's (slightly modified) suggestion to the commit header,
cleaned up whitespace. -bpm]
Determine if we've created a new file by examining the directory change
attribute and/or the O_EXCL flag.
This fixes a regression when doing a non-exclusive create of a new file.
If the FILE_CREATED flag is not set, the atomic_open() command will
perform full file access permissions checks instead of just checking
for MAY_OPEN.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Use MONITOR_FLAG_ACTIVE, which is a flag mask, instead of
NL80211_MNTR_FLAG_ACTIVE, which is a flag index, when checking if the
hardware supports active monitoring.
Cc: stable@vger.kernel.org
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
