This patch fixes the following checkpatch errors:
ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {
ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {
ERROR: space prohibited after that '!' (ctx:BxW)
+ if (! netif_carrier_ok(tp->dev) &&
^
ERROR: space required after that ',' (ctx:VxV)
+#define GET_REG32_LOOP(base,len) \
^
ERROR: "(foo*)" should be "(foo *)"
+ memcpy(data, ((char*)&val) + b_offset, b_count);
ERROR: do not use assignment in if condition
+ if ((err = tg3_do_mem_test(tp, mem_tbl[i].offset,
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 52cdf8526f,
entitled "tg3: Prevent a PCIe tx glitch". The problem does not have
any visible side-effects and happens too early for the driver to do
anything about it. The proper place for this code is within the
device's bootcode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the code so that the driver version can be reported
to the firmware in addition to the current use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 is coded to refuse to attach to 5717 serdes devices. Now that the
hardware is better supported, we can relax this restriction. This patch
also fixes a recently introduced bug which will cause serdes parallel
detection not to work with 5780 class devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_start_xmit_dma_bug() function was missing code to process IPv6
TSO packets. This patch adds the missing support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt coalescing setup code used the TG3_FLG2_USING_MSIX flag to
determine whether or not to configure the rx coalescing parameters.
This is incorrect for the single MSI-X vector case. This patch changes
the code to look at the TG3_FLG3_ENABLE_RSS instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 2601d8a004. A
spectacular set of coincidences made it look as though the table was
setup incorrectly. The original version was correct.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ 56 was not freed anywhere (neither in i596_open() on error nor in
i596_close()), rx_bufs were not freed if init_i596_mem() fails,
netif_stop_queue() was not called.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_alloc_skb() failed then free already allocated skbs.
remove_rx_bufs() can be called multiple times, so set rbd->skb to NULL
to avoid double free. remove_rx_bufs() was moved upwards to be seen by
init_rx_bufs().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is loaded in guest OS, the pci variables is_virtfn and is_physfn are
both set to 0. This change uses registers in controller to determine the same.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Non privileged (VF) driver will not be able to carry out any of the FW update,
etc. operations. Disable the tools interface by not creating the sysfs nodes.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver checks TSO capability from FW before enabling it.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document that dev_get_stats() returns the same stats pointer it was
given. Remove const qualification from the returned pointer since the
caller may do what it likes with that structure.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit be1f3c2c02 "net: Enable 64-bit
net device statistics on 32-bit architectures" I redefined struct
net_device_stats so that it could be used in a union with struct
rtnl_link_stats64, avoiding the need for explicit copying or
conversion between the two. However, this is unsafe because there is
no locking required and no lock consistently held around calls to
dev_get_stats() and use of the statistics structure it returns.
In commit 28172739f0 "net: fix 64 bit
counters on 32 bit arches" Eric Dumazet dealt with that problem by
requiring callers of dev_get_stats() to provide storage for the
result. This means that the net_device::stats64 field and the padding
in struct net_device_stats are now redundant, so remove them.
Update the comment on net_device_ops::ndo_get_stats64 to reflect its
new usage.
Change dev_txq_stats_fold() to use struct rtnl_link_stats64, since
that is what all its callers are really using and it is no longer
going to be compatible with struct net_device_stats.
Eric Dumazet suggested the separate function for the structure
conversion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we stop the Tx DMA channels, we poll bits 16:31 in
FH_TSSR_RX_STATUS_REG. From 4965 and up, only the bits 16:26 are legal.
Bits 27:31 are not used and are always unset.
Polling them will lead to fail on timeout but since the timeout is quite
small, the stall was not felt.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Intel Wireless WiFi Next Gen AGN support two major categories:
1. Intel Wireless WiFi 4965 AGN device
2. Intel Wireless-N/Advanced-N/Ultimate-N family
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
ucode errors were redefined in new ucode images and all new errors
were showing as advanced sysasserts which was misleading. new errors
are not sequential so additional lookup table added. errors do not
overlap so both are used to support older and newer ucode images.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
To enable 6050 series Gen 2 devices:
1) new PCI_IDs are added;
2) new EEPROM version and calibration version numbers defined;
3) new hardware REV number defined;
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Propagate changes to upper atm layer, so userspace netmontor knows when DSL
showtime reached.
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a signal change event occurs call netif_carrier_on/off.
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add notifier chain for changes in atm_dev.
Clients like br2684 will call register_atmdevice_notifier() to be notified of
changes. Drivers will call atm_dev_signal_change() to notify clients like
br2684 of the change.
On DSL and ATM devices it's usefull to have a know if you have a carrier
signal. netdevice LOWER_UP changes can be propagated to userspace via netlink
monitor.
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement "Unhandled Interrupts" statistic so we can detect when the
hardware tells us that it things we have work to do but we don't find
anything ...
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error path in mpc52xx_fec_probe() is broken.
We must free everything that we've allocated.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If of_iomap() or irq_of_parse_and_map() fail then np must be freed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ax_ei_open() failed we must free previously requested irq.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes an unnecessary bank select before resetting the
controller.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all code that needs to be run at TX timeout is done in the
calling context, where bottom halves are disabled. Some of the code
blocks, so it needs to be done in a different context. This patch
adds in a work struct which is scheduled at TX timeout. Then the
timeout code is executed within work queue context.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit eedc765ca4 merged changes from
net-2.6 that added and then removed efx_nic::port_num, which was also
added in net-next-2.6. The end result should be that it is removed,
since it is now unused.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 72dccb01e8 (bnx2: Update vlan_features)
In order to enable TSO on vlan devices, tg3 needs to update
dev->vlan_features.
Tested on HP NC326m (aka BCM5715S (rev a3))
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now core network is able to handle 64 bit netdevice stats on 32 bit
arches, we can provide them for tg3, since hardware maintains 64 bit
counters.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now core network is able to handle 64 bit netdevice stats on 32 bit
arches, we can provide them for bnx2, since hardware maintains some 64
bit counters.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use CONFIG_NEED_DMA_MAP_STATE to see if a platform does real
DMA unmapping.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
We could use DEFINE_DMA_UNMAP_ADDR instead but using
CONFIG_NEED_DMA_MAP_STATE is a simpler way to see if a platform does
real DMA unmapping.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we need to shape traffic using low speeds, we need to
disable tso on network interface :
ethtool -K eth0.2240 tso off
It seems vlan interfaces miss the set_tso() ethtool method.
Before enabling TSO, we must check real device supports
TSO for VLAN-tagged packets and enables TSO.
Note that a TSO change on real device propagates TSO setting
on all vlans, even if admin selected a different TSO setting.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes IPV6 over IPv4 GRE tunnel propagate the transport
class field from the underlying IPV6 header to the IPV4 Type Of Service
field. Without the patch, all IPV6 packets in tunnel look the same to QoS.
This assumes that IPV6 transport class is exactly the same
as IPv4 TOS. Not sure if that is always the case? Maybe need
to mask off some bits.
The mask and shift to get tclass is copied from ipv6/datagram.c
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were always using the max transmit power when scanning. Now we use the
values passed to the driver by the mac80211 stack, so that we comply with
regulations.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a complete rewrite of the scanning code. It now includes a
state machine to scan all four possible sets of channels independently:
2.4GHz active, 2.4GHz passive, 5GHz active and 5GHz passive. The wl1271
firmware doesn't allow these sets to be mixed, so up to several scan commands
have to be issued. This patch also allows scanning more than 24 channels per
set, by breaking the sets into smaller parts if needed (the firmware can scan
a maximum of 24 channels at a time).
Previously, the scanning code was erroneously scanning all channels possible
actively, not complying with the CRDA values. This is also fixed with this
patch.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scanning code is going to get a bit more complex, with proper support for
active/passive scans together with 2.4GHz and 5GHz. In the future, also a
new type of scan (periodic scan) will be added. When all this is
implemented, the code is going to be much more complex, so we'd better
separate it into a separate file.
This patch doesn't have any impact on functionality.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 interface to temporarily disable dynamic PS changed, make
corresponding changes to the driver.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch requests mac80211 to disable dynamic PSM based on sense events
coming from the firmware. Effectively, whenever there is bluetooth traffic,
the mac80211 is forced into full PSM mode.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interface for hardware ARP configuration changed in the mac80211. Change
driver accordingly.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
