While fw-sbp2 takes the necessary time to reconnect to a logical unit
after bus reset, the SCSI core keeps sending new commands. They are all
immediately completed with host busy status, and application clients or
filesystems will break quickly. The SCSI device might even be taken
offline: http://bugzilla.kernel.org/show_bug.cgi?id=9734
The only remedy seems to be to block the SCSI device until reconnect.
Alas the SCSI core has no useful API to block only one logical unit i.e.
the scsi_device, therefore we block the entire Scsi_Host. This
currently corresponds to an SBP-2 target. In case of targets with
multiple logical units, we need to satisfy the dependencies between
logical units by carefully tracking the blocking state of the target and
its units. We block all logical units of a target as soon as one of
them needs to be blocked, and keep them blocked until all of them are
ready to be unblocked.
Furthermore, as the history of the old sbp2 driver has shown, the
scsi_block_requests() API is a minefield with high potential of
deadlocks. We therefore take extra measures to keep logical units
unblocked during __scsi_add_device() and during shutdown.
This avoids I/O errors during reconnect in many but alas not in all
cases. There may still be errors after a re-login had to be performed.
Also, some bridges have been seen to cease fetching management ORBs if
I/O went on up until a bus reset. In these cases, all management ORBs
time out after mgt_orb_timeout. The old sbp2 driver is less vulnerable
or maybe not vulnerable to this, for as yet unknown reasons.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
fw-sbp2 is unable to reconnect while performing __scsi_add_device
because there is only a single workqueue thread context available for
both at the moment. This should be fixed eventually.
An actual failure of __scsi_add_device is easy to handle, but an
incomplete execution of __scsi_add_device with an sdev returned would
remain undetected and leave the SBP-2 target unusable.
Therefore we use a workaround: If there was a bus reset during
__scsi_add_device (i.e. during the SCSI probe), we remove the new sdev
immediately, log out, and attempt login and SCSI probe again.
Tested-by: Jarod Wilson <jwilson@redhat.com> (earlier version)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If fw-sbp2 was too late with requesting the reconnect, the target would
reject this. In this case, log out before attempting the reconnect.
Else several firmwares will deny the re-login because they somehow
didn't invalidate the old login.
Also, don't retry reconnects in this situation. The retries won't
succeed either.
These changes improve chances for successful re-login and shorten the
period during which the logical unit is inaccessible.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
When a reconnect failed but re-login succeeded, __scsi_add_device was
called again.
In those cases, __scsi_add_device succeeded and returned the pointer to
the existing scsi_device. fw-sbp2 then continued orderly, except that
it missed to call sbp2_cancel_orbs. SCSI core would call fw-sbp2's
eh_abort_handler eventually if there had been an outstanding command.
This patch avoids the needless lookups and temporary allocations in SCSI
core and I/O stall and timeout until eh_abort_handler hits.
Also, __scsi_add_device tolerating calls for devices which already exist
is undocumented behavior on which we shouldn't rely.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
for easier readable logs if more than one SBP-2 device is present.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Like the old sbp2 driver, wait for the write transaction to the
AGENT_RESET to complete before proceeding (after login, after reconnect,
or in SCSI error handling).
There is one occasion where AGENT_RESET is written to from atomic
context when getting DEAD status for a command ORB. There we still
continue without waiting for the transaction to complete because this
is more difficult to fix...
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Several different SBP-2 bridges accept a login early while the IDE
device is still powering up. They are therefore unable to respond to
SCSI INQUIRY immediately, and the SCSI core has to retry the INQUIRY.
One of these retries is typically successful, and all is well.
But in case of Momobay FX-3A, the INQUIRY retries tend to fail entirely.
This can usually be avoided by waiting a little while after login before
letting the SCSI core send the INQUIRY. The old sbp2 driver handles
this more gracefully for as yet unknown reasons (perhaps because it
waits for fetch agent resets to complete, unlike fw-sbp2 which quickly
proceeds after requesting the agent reset). Therefore the workaround is
not as much necessary for sbp2.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
This should help to interpret user reports. E.g. one can look up the
vendor OUI (first three bytes of the GUID) and thus tell what is what.
Also simplifies the math in the GUID sysfs attribute.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
If a device is being unplugged while fw-sbp2 had a login or reconnect on
schedule, it would take about half a minute to shut the fw_unit down:
Jan 27 18:34:54 stein firewire_sbp2: logged in to fw2.0 LUN 0000 (0 retries)
<unplug>
Jan 27 18:34:59 stein firewire_sbp2: sbp2_scsi_abort
Jan 27 18:34:59 stein scsi 25:0:0:0: Device offlined - not ready after error recovery
Jan 27 18:35:01 stein firewire_sbp2: orb reply timed out, rcode=0x11
Jan 27 18:35:06 stein firewire_sbp2: orb reply timed out, rcode=0x11
Jan 27 18:35:12 stein firewire_sbp2: orb reply timed out, rcode=0x11
Jan 27 18:35:17 stein firewire_sbp2: orb reply timed out, rcode=0x11
Jan 27 18:35:22 stein firewire_sbp2: orb reply timed out, rcode=0x11
Jan 27 18:35:27 stein firewire_sbp2: orb reply timed out, rcode=0x11
Jan 27 18:35:32 stein firewire_sbp2: orb reply timed out, rcode=0x11
Jan 27 18:35:32 stein firewire_sbp2: failed to login to fw2.0 LUN 0000
Jan 27 18:35:32 stein firewire_sbp2: released fw2.0
After this patch, typically only a few seconds spent in __scsi_add_device
remain:
Jan 27 19:05:50 stein firewire_sbp2: logged in to fw2.0 LUN 0000 (0 retries)
<unplug>
Jan 27 19:05:56 stein firewire_sbp2: sbp2_scsi_abort
Jan 27 19:05:56 stein scsi 33:0:0:0: Device offlined - not ready after error recovery
Jan 27 19:05:56 stein firewire_sbp2: released fw2.0
The benefit of this is less noise in the syslog. It furthermore avoids
a few wasted CPU cycles and needlessly prolonged lifetime of a few
driver objects.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
There is a race between shutdown and creation of devices: fw-core may
attempt to add a device with the same name of an already existing
device. http://bugzilla.kernel.org/show_bug.cgi?id=9828
Impact of the bug: Happens rarely (when shutdown of a device coincides
with creation of another), forces the user to unplug and replug the new
device to get it working.
The fix is obvious: Free the minor number *after* instead of *before*
device_unregister(). This requires to take an additional reference of
the fw_device as long as the IDR tree points to it.
And while we are at it, we fix an additional race condition:
fw_device_op_open() took its reference of the fw_device a little bit too
late, hence was in danger to access an already invalid fw_device.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This fixes a "can't recognize device" kind of bug.
If the SCSI INQUIRY failed and hence __scsi_add_device failed due to a
bus reset, we tried a logout and then waited for the already scheduled
login work to happen. So far so good, but the generation used for the
logout was outdated, hence the logout never reached the target. The
target might therefore deny the subsequent relogin attempt, which would
also leave the target inaccessible.
Therefore fetch a fresh device->generation for the logout. Use memory
barriers to prevent our plan being foiled by compiler or hardware
optimizations.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
To be more compliant with section 7.4.8 of the SBP-2 specification,
use the mgt_ORB_timeout specified in the SBP-2 device's config rom
for login ORB attempts (though with some sanity checks). A happy
side-effect is that certain device and controller combinations that
sometimes take more than 20 seconds to get synced up (like my laptop
with just about any SBP-2 device) now function more reliably.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (silenced sparse)
Increase (and rename) the login orb reply timeout value to 20s
to match that of the old firewire stack. 2s simply didn't give
many devices enough time to spin up and reply.
Fixes inability to recognize some devices.
Failure mode was "orb reply timed out"/"failed to login".
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (style, comments, changelog)
Replace an unnecessary subtraction with a bitwise AND when determining the
value of ext_tcode in fw_fill_transaction() to save a cpu cycle or two in a
somewhat critical path.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
read_rom() obtained a fresh new fw_device.generation for each read
transaction. Hence it was able to continue reading in the middle of the
ROM even if a bus reset happened. However the device may have modified
the ROM during the reset. We would end up with a corrupt fetched ROM
image then.
Although all of this is quite unlikely, it is not impossible.
Therefore we now restart reading the ROM if the bus generation changed.
Note, the memory barrier in read_rom() is still necessary according to
tests by Jarod Wilson, despite of the ->generation access being moved up
in the call chain.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This is essentially what I've been beating on locally, and I've yet to hit
another config rom read failure with it.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
fw_device.node_id and fw_device.generation are accessed without mutexes.
We have to ensure that all readers will get to see node_id updates
before generation updates.
Fixes an inability to recognize devices after "giving up on config rom",
https://bugzilla.redhat.com/show_bug.cgi?id=429950
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reviewed by Nick Piggin <nickpiggin@yahoo.com.au>.
Verified to fix 'giving up on config rom' issues on multiple system and
drive combinations that were previously affected.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
We have to use the fw_device.generation here, not the fw_card.generation,
because the generation must never be newer than the node ID when we emit
a transaction. This cannot be guaranteed with fw_card.generation.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Verified in concert with subsequent memory barriers patch to fix 'giving
up on config rom' issues on multiple system and drive combinations that
were previously affected.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
There was a small window where a login or reconnect job could use an
already updated card generation with an outdated node ID. We have to
use the fw_device.generation here, not the fw_card.generation, because
the generation must never be newer than the node ID when we emit a
transaction. This cannot be guaranteed with fw_card.generation.
Furthermore, the target's and initiator's node IDs can be obtained from
fw_device and fw_card. Dereferencing their underlying topology objects
is not necessary.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Verified in concert with subsequent memory barriers patch to fix 'giving
up on config rom' issues on multiple system and drive combinations that
were previously affected.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Ask the target to grant 4 seconds instead of the standard and minimum of
1 second window after bus reset for reconnection. This accelerates
reconnection if there are more than one targets on the bus: If a login
and inquiry to one target blocks the fw-sbp2 workqueue for more than 1s
after bus reset, we now still can reconnect to the other target.
Before that, fw-sbp2's reconnect attempts would be rejected with "error
status: 0:9" (function rejected), and fw-sbp2 would finally re-login.
All those futile reconnect attemps cost extra time until the target
which needs re-login is ready for I/O again.
The reconnect timeout field in the login ORB doesn't have to be honored
by the target though. I found that we could get up to
- allegedly 32768s from an old OXFW911 firmware
- 256s from LSI bridges
- 4s from OXUF922 and OXFW912 bridges,
- 2s from TI bridges,
- only the standard 1s from Initio and Prolific bridges and from
Apple OpenFirmware in target mode.
We just try to get 4 seconds which already covers the case of a few
HDDs on the same bus quite nicely.
A minor drawback occurs in the following (rare and impractical) border
case:
- two initiators are there, initiator 1 holds an exclusive login to
a target,
- initiator 1 goes off the bus,
- target refuses login attempts from initiator 2 until reconnect_hold
seconds after bus reset.
An alternative approach to the issue at hand would be to parallelize
fw-sbp2's reconnect and login work.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Don't attempt to send a logout ORB if the target was already unplugged
or had its link switched off. If two targets are attached, this
enhances the chance to quickly reconnect to the remaining target when
one target is plugged out.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Previously, the fw-ohci driver used fixed-length buffers for storing
descriptors for isochronous receive DMA programs. If an application
(such as libdc1394) generated a DMA program that was too large, fw-ohci
would reach the limit of its fixed-sized buffer and return an error to
userspace.
This patch replaces the fixed-length ring-buffer with a linked-list of
page-sized buffers. Additional buffers can be dynamically allocated and
appended to the list when necessary. For a particular context, buffers
are kept around after use and reused as necessary, so there is no
allocation taking place after the DMA program is generated for the first
time.
In addition, the buffers it uses are coherent for DMA so there is no
syncing required before and after writes. This syncing wasn't properly
done in the previous version of the code.
-
This is the fourth version of my patch that replaces a fixed-length
buffer for DMA descriptors with a dynamically allocated linked-list of
buffers.
As we discovered with the last attempt, new context programs are
sometimes queued from interrupt context, making it unacceptable to call
tasklet_disable() from context_get_descriptors().
This version of the patch uses ohci->lock for all locking needs instead
of tasklet_disable/enable. There is a new requirement that
context_get_descriptors() be called while holding ohci->lock. It was
already held for the AT context, so adding the requirement for the iso
context did not seem particularly onerous. In addition, this has the
side benefit of allowing iso queue to be safely called from concurrent
user-space threads, which previously was not safe.
Signed-off-by: David Moore <dcm@acm.org>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
-
Fixes the following issues:
- Isochronous reception stopped prematurely if an application used a
larger buffer. (Reproduced with coriander.)
- Isochronous reception stopped after one or a few frames on VT630x
in OHCI 1.0 mode. (Fixes reception in coriander, but dvgrab still
doesn't work with these chips.)
Patch update: struct member alignment, whitespace nits
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The firewire-ohci driver so far lacked the ability to resume cycle
master duty after that condition happened, as added to ohci1394 in Linux
2.6.18 by commit 57fdb58fa5. This ports
this patch to fw-ohci.
The "cycle too long" condition has been seen in practice
- with IIDC cameras if a mode with packets too large for a speed is
chosen,
- sporadically when capturing DV on a VIA VT6306 card with ohci1394/
ieee1394/ raw1394/ dvgrab 2.
https://bugzilla.redhat.com/show_bug.cgi?id=415841#c7
(This does not fix Fedora bug 415841.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix extraction of the source node id from the packet header.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch corrects a number of bugs in the current OHCI 1.0
packet-per-buffer support:
1. Correctly deal with payloads that cross a page boundary. The
previous version would not split the descriptor at such a boundary,
potentially corrupting unrelated memory.
2. Allow user-space to specify multiple packets per struct
fw_cdev_iso_packet in the same way that dual-buffer allows. This is
signaled by header_length being a multiple of header_size. This
multiple determines the number of packets. The payload size allocated
per packet is determined by dividing the total payload size by the
number of packets.
3. Make sync support work properly for packet-per-buffer.
I have tested this patch with libdc1394 by forcing my OHCI 1.1
controller to use the packet-per-buffer support instead of dual-buffer.
I would greatly appreciate testing by those who have a DV devices and
other types of iso streamers to make sure I didn't cause any
regressions.
Stefan, with this patch, I'm hoping that libdc1394 will work with all
your OHCI 1.0 controllers now.
The one bit of future work that remains for packet-per-buffer support is
the automatic compaction of short payloads that I discussed with
Kristian.
Signed-off-by: David Moore <dcm@acm.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch fixes the problem where different OHCI 1.1 controllers behave
differently when a received iso packet straddles three or more buffers
when using the dual-buffer receive mode. Two changes are made in order
to handle this situation:
1. The packet sync DMA descriptor is given a non-zero header length and
non-zero payload length. This is because zero-payload descriptors are
not discussed in the OHCI 1.1 specs and their behavior is thus
undefined. Instead we use a header size just large enough for a single
header and a payload length of 4 bytes for this first descriptor.
2. As we process received packets in the context's tasklet, read the
packet length out of the headers. Keep track of the running total of
the packet length as "excess_bytes", so we can ignore any descriptors
where no packet starts or ends. These descriptors may not have had
their first_res_count or second_res_count fields updated by the
controller so we cannot rely on those values.
The main drawback of this patch is that the excess_bytes value might get
"out of sync" with the packet descriptors if something strange happens
to the DMA program. I'm not if such a thing could ever happen, but I
appreciate any suggestions in making it more robust.
Also, the packet-per-buffer support may need a similar fix to deal with
issue 1, but I haven't done any work on that yet.
Stefan, I'm hoping that with this patch, all your OHCI 1.1 controllers
will work properly with an unmodified version of libdc1394.
Signed-off-by: David Moore <dcm@acm.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
SBP2_MAX_SECTORS is nowhere used in fw-sbp2.
It merely got copied over from sbp2 where it played a role in the past.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes. I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.
The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev. (basically all inquiries it
issues can now be directly mapped).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Third rendition of FireWire OHCI 1.0 Isochronous Receive support, using a
zer-copy method similar to OHCI 1.1 which puts the IR data payload directly
into the userspace buffer. The zero-copy implementation eliminates the
video artifacts, audio popping, and buffer underrun problems seen with
version 1 of this patch, as well as fixing a regression in OHCI 1.1 support
introduced by version 2 of this patch.
Successfully tested in OHCI 1.1 mode on the following chipsets:
- NEC uPD72847 (rev 01), OHCI 1.1 (PCI)
- Ti XIO2200(A) (rev 01), OHCI 1.1 (PCIe)
- Ti TSB41AB2 (rev 01), OHCI 1.1 (PCI on SB Audigy)
- Apple UniNorth 2 (rev 81), OHCI 1.1 (PowerBook G4 onboard)
Successfully tested in OHCI 1.0 mode on the following chipsets:
- Agere FW323 (rev 06), OHCI 1.0 (Mac Mini onboard)
- Agere FW323 (rev 06), OHCI 1.0 (PCI)
- Via VT6306 (rev 46), OHCI 1.0 (PCI)
- NEC OrangeLink (rev 01), OHCI 1.0 (PCI)
- NEC uPD72847 (rev 01), OHCI 1.1 (PCI)
- Ti XIO2200(A) (rev 01), OHCI 1.1 (PCIe)
The bulk of testing was done in an x86_64 system, but was also successfully
sanity-tested on other systems, including a PPC(32) PowerBook G4 and an i686
EPIA M10k. Crude benchmarking (watching top during capture) puts the cpu
utilization during capture on the EPIA's 1GHz Via C3 processor around 13%,
which is down from 30% with the v1 code.
Some implementation details:
To maintain the same userspace API as dual-buffer mode, we set up two
descriptors for every incoming packet. The first is an INPUT_MORE descriptor,
pointing to a buffer large enough to hold just the packet's iso headers,
immediately followed by an INPUT_LAST descriptor, pointing to a chunk of the
userspace buffer big enough for the packet's data payload. With this setup,
each incoming packet fills in these two descriptors in a manner that very
closely emulates dual-buffer receive, to the point where the bulk of the
handle_ir_* code is now identical between the two (and probably primed for
some restructuring to share code between them).
The only caveat I have at the moment is that neither of my OHCI 1.0 Via
VT6307-based FireWire controllers work particularly well with this code
for reasons I have yet to figure out.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Since patch "fw-sbp2: use an own workqueue (fix system responsiveness)"
increased parallelism between fw-sbp2 and fw-core, it was possible that
fw-sbp2 didn't release the SCSI device when the FireWire device was
disconnected.
This happened if sbp2_update() ran during sbp2_login(), because a bus
reset occurred during sbp2_login(). The sbp2_login() work would [try
to] reschedule itself because it failed due to the bus reset, and it
would _not_ drop its reference on the target. However, sbp2_update()
would schedule sbp2_login() too before sbp2_login() rescheduled itself
and hence sbp2_update() would take an additional reference. And then
we would have one reference too many.
The fix is to _always_ drop the reference when leaving the sbp2_login()
work. If the sbp2_login() work reschedules itself, it takes a
reference, but only if it wasn't already rescheduled by sbp2_update().
Ditto in the sbp2_reconnect() work.
The resulting code is actually simpler than before: We _always_ take
a reference when successfully scheduling work. And we _always_ drop
a reference when leaving a workqueue job. No exceptions.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The ohci_enable() function shared between pci_probe and pci_resume
takes a host endian config rom, but ohci->config_rom is __be32. This
sets up the config rom in the wrong endian on little endian machine,
specifically, BusOptions will be initialized to a 0 max receive size.
This patch changes the way we reuse the config rom so that we avoid
this problem.
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
New warning since commit ab88ca488b,
"firewire: fw-ohci: missing dma_unmap_single":
drivers/firewire/fw-ohci.c: In function 'at_context_transmit':
drivers/firewire/fw-ohci.c:609: warning: 'payload_bus' may be used
uninitialized in this function
Access to payload_bus is conditional on packet->payload_length > 0,
and that won't change while in at_context_queue_packet.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
because there seems to be more time needed to implement this.
Also, change related error return values to more appropriate ones.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This duplicates the read cycle timer feature of raw1394 (added in Linux
2.6.21) in firewire-core's userspace ABI. The argument to the ioctl is
reordered though to ensure 32/64 bit compatibility.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Check NodeID.nodeNumber as per OHCI 1.1 clause 7.2.3.2. See also IEEE
1394a table 5B-1.
Also, demote the "node ID not valid" message from error to notification
as it is not an error condition.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
at_context_queue_packet() didn't clean up in an early exit path.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
It seems unlikely, but access to self_id_cpu[0] could at least in theory
be deferred until after the loop over self_id_cpu[1..n] or even after
the subsequent reg_read. Enforce the desired order by a read barrier.
Also prevent the reg_read from being reordered relative to the for loop.
This isn't necessary if the loop's conditional printk counts as an
implicit barrier, but better make it explicit.
(self_id_cpu[] is a coherent DMA buffer.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Firewire-sbp2 did very uncooperative things in the kernel's shared
workqueue: Sleeping until reception of management status from the
target for up to 2 seconds, and performing SCSI inquiry and all of the
setup of SCSI command set drivers via scsi_add_device. If there were
transient or permanent error conditions, this caused long blockage of
the kernel's events process, noticeable e.g. by blocked keyboard input.
We now allocate a workqueue process exclusive to fw-sbp2. As a side
effect, this also increases parallelism of fw-sbp2's login and reconnect
work versus fw-core's device discovery and device update work which is
performed in the shared workqueue.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
On rare occasions, the ability to set one of the workaround flags at
runtime may save the day.
People who experience I/O errors with firewire-sbp2 while the old sbp2
driver worked for them should try workarounds=1 and report to the devel
mailinglist whether that improves things. Firewire-sbp2 defaults to the
SCSI stack's maximum transfer size per command, while sbp2 limits them
to 128 kBytes. Flag 1 accomplishes just that.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On IOMMU-less noncoherent architectures, orb->callback will memcpy the
whole SCSI command buffer for READ-like SCSI commands. It is therefore
friendlier to enable IRQs before the call, like before patch "Add
ref-counting for sbp2 orbs".
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Sparse warned about it although it was apparently harmless:
drivers/firewire/fw-cdev.c:624:23: warning: symbol 'interrupt' shadows an earlier one
include/asm/hw_irq.h:29:13: originally declared here
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes (papers over) "Sleep problems with kernels >= 2.6.21 on powerpc",
http://lkml.org/lkml/2007/8/25/155. The issue is that the FireWire
controller's pci_dev.current_state of iBook G3 and presumably older
PowerBooks is still in PCI_UNKNOWN instead of PCI_D0 when the firewire
driver's .suspend method is called.
Like it was suggested earlier in http://lkml.org/lkml/2006/10/24/13, we
do not fail .suspend anymore if pci_set_power_state failed.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This handles the case where we get the status write before getting the
complete_transaction callback ("status write for unknown orb"). In
this case, we just assume that the initial orb pointer transaction
succeeded and finish the orb. To prevent the transaction callback
from touching freed memory, we ref-count the orb structures.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix panic in run_timer_softirq right after "modprobe -r firewire-ohci"
if a FireWire disk was attached and firewire-sbp2 loaded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
As far as I know, all CardBus FireWire 400 adapters have a maximum
payload of 1024 bytes which is less than the speed-dependent limit of
2048 bytes. Fw-sbp2 has to take the host adapter's limit into account.
This apparently fixes Juju's incompatibility with my CardBus cards, a
NEC based card and a VIA based card.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
collapsed with fw-sbp2 patch "Drop cast to non-const char * in host
template initialization." from Kristian Høgsberg
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Found and debugged by Jay Fenlason <fenlason@redhat.com>.
The bug was especially noticeable with direct I/O over fw-sbp2.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
This check is bogus:
- Maximum asynchronous payload size for S800...S3200 is 4096.
- The p->payload_length is totally uninteresting. Only the
request->length of the subsequently allocated and initialized
struct fw_request is of significance.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
The CPU must not touch the buffer after it was DMA-mapped.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
The CPU must not touch the buffer after it was DMA-mapped.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
- The CPU must not touch the buffer after it was DMA-mapped.
- The size argument of dma_unmap_single(...page_table...) was bogus.
- Move a comment closer to the code to which it refers to.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Add rudimentary check for the case that the page table overflows due to
merging of s/g elements by the IOMMU. This would have lead to
overwriting of arbitrary memory.
After this change I expect that an offending command will be
unsuccessfully retried until the scsi_device is taken offline by SCSI
core. It's a border case and not worth to implement a recovery
strategy.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Replace a cast with a container_of(). As long as nobody reorders the
structure elements, they do the same thing, but container_of() is more
readable.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added complete_command_orb)
Acked-by: Kristian Høgsberg <krh@redhat.com>
This affects of course only the "soft shutdown" case, e.g. "modprobe -r
firewire-sbp2", while it doesn't matter for hot unplug.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
This currently only affects one bridge in the hardwired blacklist.
I don't own one of those, hence haven't tested it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
cleanup after "firewire: support S100B...S400B and link slower than PHY"
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Use a speed probe to determine the speed over 1394b buses and of nodes
which report a link speed less than their PHY speed.
Log the effective maximum speed of newly created nodes in dmesg.
Also, read the config ROM (except bus info block) at the maximum speed
rather than S100. This isn't a real optimization though because we
still only use quadlet read requests for the entire ROM.
The patch also adds support for S1600 and S3200, although such hardware
does not exist yet.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Table-based gap count optimization cannot be used if 1394b repeater PHYs
are present. But it does work with 1394b leaf nodes.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
cleanup after support of single-buffer requests was dropped
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Alas that won't work so good, because nobody reads help texts.
I thought about adding some crude multiple choice selection (build the
old stack, build the new stack, build both stacks). It's possible, but
it would introduce awkward dummy config variables.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
descriptor.data_address is little endian
Tested-by: Olaf Hering <olh@suse.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
This patch fixes an OOPS on cdev release for an fd where iso context
creation failed.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The struct is part of the userspace interface and can not use
bitfields. This patch replaces the bitfields with a __u32 'control'
word and provides access macros to set the bits.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
It's a low-impact design, that just makes suspend/resume look like
a bus reset to the upper level drivers, but it should be sufficient.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The attribute /sys/bus/scsi/devices/*:*:*:*/ieee1394_id, as generated by
the old sbp2 driver, is typically used to create persistently named
links in /dev/disk/by-id.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Fix this warning on x86-64
drivers/firewire/fw-cdev.c:798: warning: initialization from incompatible pointer type
by making the return code of ioctl_send_request() the same as all the
other ioctl_xxx() return codes.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Of course everybody immediately associates "fw-" with FireWire, not
firmware or firewall or whatever. But "firewire-" has a nice ring to
it too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Hoegsberg <krh@bitplanet.net>
need it for page_private(), not all targets have it pulled indirectly
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SCSI layer only passes sg requests down, so drop the
use_sg == 0, request_bufflen != 0 case.
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Avoids an extra allocation and simplifies lifetime rules for the scsi_host.
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch loads fw-sbp2 if sbp2 is still in the config file. So one can
go back and forth between releases without worry about the root
filesystem drivers.
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Existing mkinitrd scripts still have to be adapted, unless they grok
module aliases.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Drop filenames from file preamble, drop editor annotations and
use standard indent style for block comments.
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (fixed typo)
With the CRC ITU-T implementation available in lib/ we can use that instead.
This also fixes a bug in the topology map crc computation.
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (fixed Kconfig)
Currently create context always returns 0 and the other iso
ioctls will expect user space to pass that in for subsequent ioctls.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Also, with this change, refactor ioctl dispatch code to do the
copying from and to user space as indicated by the IOC annotations.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Make firewire entry points not 'extern':
drivers/firewire/fw-device.c:160:25: warning: function 'fw_device_get' with external linkage has definition
drivers/firewire/fw-device.c:167:13: warning: function 'fw_device_put' with external linkage has definition
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
You don't know what type is used to implement u64.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
(Reverted part which moved it from eh_abort_handler to eh_host_reset_handler)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In some situations we can receive the ORB status write before we
have received the ORB pointer write response. When this happens,
we assume that the fw_transaction is finished and free the ORB
struct containing the fw_transaction.
This fix make the status write logic only accept status writes
for ORBs where the initial ORB pointer write transaction finished.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Or the SAM status codes from the device sense data into the
command error code.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Some devices have a really long power-on cycle, and we fail to
successfully probe these if they're plugged in and then turned on.
There's really no down-side to bumping the number of retries and the
retry delay, and most devices will get picked up within the first couple
of retries anyway.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In case the topology build fails, we want to retain the old topology
info until another reset finishes and results in a valid new tree. If
we clear card->irm_node to NULL and the topology build fails, we end up
dereferencing a NULL pointer in a few places.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Generalize the way we keep track of the various resources and
assign a unique handle to each resource.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Make event struct layout common part include the closure and add a
union for all event types; provide a mechanism for setting the
bus reset event closure.
Shuffle struct fw_cdev_queue_iso fields around to be 64-bit safe.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We dynamically create an attribute group for the key present on the
device in hand and point device->group to it. This way the device
core adds the sysfs attributes for us as the device is added.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Marc Butler <marc@adaptivecode.com>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added whitespace)
We export the entire config rom, so this is technically redundant,
but should make udev rules and HAL integration easier.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The device_type struct is useful for setting attributes for a device
and overriding .release and .uevent for a group of devices. This patch
uses it this way to clean up the sysfs code a bit.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This serializes the update callback with the probe and remove callback from
the driver core and prevents remove from being called while update is
running for the same device.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Setting these at create_context time or start_iso time doesn't matter
much, but raw1394 sets them at start_iso time so that will be easier to
emulate this way.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The dualbuffer DMA setup did not account for the iso trailer word
and thus didn't work correctly. With this fixed we can drop the
dual buffer fallback mode.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
