* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: (53 commits)
hwmon: (vt8231) fix sparse warning
hwmon: (sis5595) fix sparse warning
hwmon: (w83627hf) don't assume bank 0
hwmon: (w83627hf) Fix setting fan min right after driver load
hwmon: (w83627hf) De-macro sysfs callback functions
hwmon: Add new combined driver for FSC chips
hwmon: (ibmpex) Release IPMI user if hwmon registration fails
hwmon: (dme1737) Add sch311x support
hwmon: (dme1737) group functions logically
hwmon: (dme1737) cleanups
hwmon: IBM power meter driver
hwmon: (coretemp) Add support for Celeron 4xx
hwmon: (lm87) Disable VID when it should be
hwmon: (w83781d) Add individual alarm and beep files
hwmon: VRM is not read from registers
MAINTAINERS: update hwmon subsystem git trees
hwmon: Fix the code examples in documentation
hwmon: update sysfs interface document - error handling
hwmon: (thmc50) Fix a debug message
hwmon: (thmc50) Don't create temp3 if not enabled
...
Convert from class_device to device for hwmon_device_register/unregister
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Three main sets of changes:
1) dmi_get_system_info() return value should have been marked const,
since callers should not be changing that data.
2) const-ify DMI internals, since DMI firmware tables should,
whenever possible, be marked const to ensure we never ever write to
that data area.
3) const-ify DMI API, to enable marking tables const where possible
in low-level drivers.
And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.
The bulk of the changes are #2 and #3, which are interrelated. #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With this patch the abituguru refuses to load on non Abit motherboards, as
discussed in lkml CONFIG_BREAK_MY_MACHINE thread.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds a new driver for the hardware monitoring features of the
third revision of the Abit uGuru chip, found on recent Abit
motherboards. This is an entirely different beast then the first and
second revision (its again a winbond microcontroller, but the "protocol"
to talk to it and the bank addresses are very different.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch fixes the detection of volt inputs with a reading of more then 240
units.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix a potential race condition when some hardware monitoring platform
drivers are being unloaded. I believe that the driver data pointer
shouldn't be cleared before all the sysfs files are removed, otherwise
a sysfs callback might attempt to dereference a NULL pointer. I'm not
sure exactly what the driver core protects drivers against, so let's
play it safe.
While we're here, clear the driver data pointer when probe fails, so
as to not leave an invalid pointer behind us.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix an unused return value warning for the abituguru driver.
Also make sure the sysfs files are created before we register with
the hwmon class, and delete the sysfs files on driver removal.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch contains rudimentary suspend / resume support for the uguru,
this protects the uguru and the driver against suspend / resume cycles,
so there is no reason to unload the driver in your suspend / resume
scripts.
Only include suspend / resume functions when CONFIG_PM is set.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains 2 sets of fixes for the abituguru:
1) Much improved timeout handling, drasticly reducing the amount of
timeout errors on some motherboards
2) Fix the exit paths in the bank1 sensor type detect code to always
restore the original settings even on an error. Without this our
special test settings could remain seriously confusing the system
BIOS's setup menu.
Both are very much related and are must haves, to avoid messing up the
uguru CMOS settings.
Detailed changes:
- Much improved timeout / wait for status handling. Many thanks to Sunil
Kumar, for all his testing, ideas and patches! The code now first busy
waits, polling the uguru for the expected status as this usually
succeeds pretty quickly (within 90 reads). To avoid unnecessary CPU burn
in timeout conditions, the amount of busy waiting has been halved from
previous versions (120 tries instead of 250). This is not a problem,
because this version goes to sleep after 120 attemps for 1 jiffy and
then tries again, it does this sleep and try again 5 times before
finally giving up. This (almost?) completly removes the timeout errors
some people have seen regulary. Apparently some older uguru versions
sometimes are distracted for a (relatively) long time. This solves this.
- These timeout errors not only occur in the sending address part of
reading the uguru but also in the wait for read state, so errors in
this state are now handled as retryable just like send address state
errors and are only logged and reported to userspace if 3 executive
tries fail.
- Fix a very nasty bug in the bank1 sensor type detection code, where it
would not restore the original settings in any of the error paths!
- Since not successfully restoring the original settings can seriously
confuse the system BIOS (hang when entering the relevant setup menu),
we now try restoring them 3 times before giving up.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the abituguru driver is seeing some more widespread testing
it has turned out that one the first generation of Abit uGuru
motherboards, with uGuru revision 1, the autodetect bank1 sensor type
code doesn't (always) work. This patch adds a module param to override
the autodetect, and it adds validity checks for the value of the 2
other autodetection override module params. An example of howto use
the new param can be found here:
http://lm-sensors.org/wiki/Configurations/Abit/AN7
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One of my testers had a problem where the driver only saw 2 of the 4 fan
sensors his uGuru has, this fixes this.
-accept 0x40 (bit 6) being high as a valid fan sensor setting for all fans
not just fan 1, I have a feeling this bit indicates whether or not a fan is
actually connected .
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes to the Abit uGuru driver as requested in review by Jean Delvare:
- exactly calculate the sysfs_names array length using macro
- use snprintf when generating names to double check that the sysfs_names
array does not overflow.
- use ARRAY_SIZE and / or defines to determine number of loops in for loops
instead of using hardcoded values.
- In abituguru_probe(), refactor the error path leaving a single call to kfree
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New hardware monitoring driver for the Abit uGuru
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds