Mark request status as done for Read Local Version HCI command. In AMP
initialization this HCI command is the last and needs to be completed.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With Bluetooth 1.1 controllers the last command in the HCI init sequence
will be a write_local_name, however there was no callback to indicate
init request completion in this case. This patch fixes the issue by
adding the necessary callback to the write_local_name_complete handler.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch updates the Device Connected events to match the latest API
by adding a flags parameter to them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
If controller is reset during the discovery procedure, Start Discovery
command stops working. This can be easily reproduced by running
"hciconfig hci0 reset" while discovering devices, for instance.
We should force discovery state to DISCOVERY_STOPPED in case we receive
a reset command complete event. Otherwise we may stuck in one of the
active discovery states (DISCOVERY_INQUIRY, DISCOVERY_LE_SCAN and
DISCOVERY_RESOLVING) and subsequent Start Discovery commands will simply
fail.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch makes sure that legacy pairing vs SSP infomation gets
properly propageted to the device_found events in the form of the legacy
pairing flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes it possible to set the local name before powering on
the device. The name will be applied using the hci_write_local_name
command once the device gets powered on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The local name should only be updated as a consequence of a
hci_read_local_name if we are in the HCI_SETUP state. In all other
scenarios it should only be updated through hci_write_local_name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Currently there are no events to other management sockets if the class of
device got changed. So make sure they are sent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Whenever we update the local device name the EIR data also needs to be
updated to reflect this. The update_eir() function in mgmt.c depends on
hdev->dev_name to be up to date so the patch also makes sure that the
mgmt function is called from hci_event.c after the update has happened.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements support for the Set LE mgmt command. Now, in
addition to the enable_le module parameter user space needs to send an
explicit Enable LE command to enable LE support.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Some controllers preserve their EIR data even after a reset so we need
to explicitly clear this during the device setup procedure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes it possible to enable SSP through mgmt even when
powered off. The setting will then get automatically actiated when
powering on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The kernel has no need to track the hci_read_ssp_mode command since it
has the hci_sent_cmd_data function to check what value was set when
hci_write_ssp_mode completes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes it possible to change the Link Security setting while
powered off and have it automatically enabled when powering on a device.
To track the desired state once powered on a new HCI_LINK_SECURITY flag
is added.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Now that most flags are persistent, only the LE_SCAN flag should be
cleared after a reset.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Since neither High Speed (HS) nor Low Energy (LE) are fully implemented
yet, only expose them in supported settings when enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI notifier handling was never used outside of Bluetooth core layer
and thus remove it and replace it with direct function calls. Also move
the stack internal event generation into the HCI socket layer.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The sending functions for HCI raw and control sockets have nothing in
common except that they iterate over the socket list. Split them into
two so they can do their job more efficient. In addition the code becomes
more readable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds interleaved discovery support to MGMT Start
Discovery command.
In case interleaved discovery is not supported (not a dual mode
device), we perform BR/EDR or LE-only discovery according to the
device capabilities.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch merges DISCOVERY_INQUIRY and DISCOVERY_LE_SCAN states
into a new state called DISCOVERY_FINDING.
From the discovery perspective, we are pretty much worried about
to know just if we are finding devices than what exactly phase of
"finding devices" (inquiry or LE scan) we are currently running.
Besides, to know if the controller is performing inquiry or LE scan
we should check HCI_INQUIRY or HCI_LE_SCAN bits in hdev flags.
Moreover, merging this two states will simplify the discovery state
machine and will keep interleaved discovery implementation simpler.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Set SSP mgmt command can be used for enabling and disabling Secure
Simple Pairing support for controllers that support it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The Set Link Security mgmt command is used to enable or disable link
level security, also known as Security Mode 3. This is rarely enabled in
modern systems but the command needs to be available for completeness,
qualification purposes and those few systems that actually want to
enable it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the Authentication Failed mgmt event to match the
latest API specification by adding an address type to it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch upadate the user confirm and user passkey mgmt messages to
match the latest API specification by adding an address type parameter
to them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an address type parameter to the disconnect command and
response in order to match the latest mgmt API specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds LE-Only discovery procedure support to MGMT Start
Discovery command.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds to hci_core the hci_do_le_scan function which
should be used to scan LE devices.
In order to enable LE scan, hci_do_le_scan() sends commands (Set
LE Scan Parameters and Set LE Scan Enable) to the controller and
waits for its results. If commands were executed successfully a
delayed work is scheduled to disable the ongoing scanning after
some amount of time. This function blocks.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Send MGMT Discovering events once LE scan starts/stops so the
userspace can track when local adapters are discovering LE devices.
This way, we also keep the same behavior of inquiry which sends MGMT
Discovering events once inquiry starts/stops even if it is triggered
by an external tool (e.g. hcitool).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This updates all the users of the older way, that was using the
link_keys list to store the SMP keys, to use the new way.
This includes defining new types for the keys, we have a type for each
combination of STK/LTK and Master/Slave.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch fixes clearing of HCI_LINK_KEYS and HCI_DEBUG_KEYS
dev_flags while resetting. Without this patch pairing does
not work over management interface for BR-EDR devices.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch sends correct IO Capability response to remote device
in case Local Device supports KeyBoardDisplay IO Capability as
this capability is not valid as per BT spec for IO capability
Request Reply Command.
This capability is mapped to DisplayYesNo which is in accordance
with BT spec.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's a very common test to see if both the local and the remote device
have SSP enabled. By creating a simple function to test this we can
shorten many if-statements in the code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The ssp_mode is essentially just a boolean so it's more appropriate to
have it simply as a flag in hdev->dev_flags.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Now that the flags member of struct hci_conn is supposed to accommodate
any boolean type values we can easily merge all boolean members into it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates mgmt_ev_device_connected and mgmt_ev_device found to
include an EIR-encoded remote name and class whenever possible. With
this addition the mgmt_ev_remote_name event becomes unnecessary and can
be removed. Since the connected event doesn't map to hci_conn_complete
anymore a HCI_CONN_MGMT_CONNECTED flag is added to track when mgmt has
been notified about a connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The hdev->out variable is essentially a boolean so the type 'bool' makes
more sense than u8.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
These flags can and will be used for more general purpose values than
just pending state transitions so the more common name "flags" makes
more sense than "pend".
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This makes the function accessible from all places it's needed (e.g.
mgmt.c and hci_event.c).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This allows for other uses such as checking for an embedded class of
device value in order to decide whether to append the class or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
User space uses device_(dis)connected instead of just (dis)connected so
rename the defines and functions to match this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
There are several other dev_flags besided HCI_MGMT that should not be
cleared upon reset.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Devices found during LE scan should be reported to userspace through
mgmt_device_found events.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a new parameter to mgmt_device_found() to inform
the length of 'eir' pointer.
EIR data from LE advertising report event doesn't have a fixed length
as EIR data from extended inquiry result event does. We needed to
change mgmt_device_found() so it copies 'eir_len' bytes instead of
HCI_MAX_EIR_LENGTH.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI_MGMT flag should not be cleared when resetting a HCI device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
There's no point in exposing these to user-space (which is what happens
to everything in hdev->flags) so move them to dev_flags instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Adds support for Number Of Completed Data Blocks Event.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the necessary logic to perform name lookups after
inquiry completes. This is done by checking for entries in the resolve
list after each inquiry complete and remote name complete HCI event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds proper state tracking to the device discovery process.
This makes it possible to return appropriate errors when trying to stop
a non-active discovery or start discovery when it is already ongoing.
Once name resolving is implemented this also makes it possible to know
what the right action to do is when a remote name lookup is cancelled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
If user-space has already confirmed the name for a remote device we
shouldn't request confirmation again. The simplest way to do this is to
return the name state from hci_inquiry_cache_update (if it is anything
else than unknown then we do not need confirmation from user-space).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds initial support for mgmt_confirm_name. It adds the
necessary tracking of the name state by extending the inquiry cache. The
actual name resolving operation (to be done once inquiry is finished) is
not yet part of this patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch queues hdev->adv_work on the system-wide workqueue
instead of on hdev->workqueue. This way we keep only tx/rx works
on hdev->workqueue.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch fixes the adv_work delay. It should be set to ADV_
CLEAR_TIMEOUT instead of (jiffies + ADV_CLEAR_TIMEOUT) since
queue_delayed_work() receives the number of jiffies to wait
before queueing. It also removes the unnecessary cancel_delayed_
work_sync() call in case LE scan has been disabled.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Copy the Features value according to the Page number.
Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch renames hdev->extfeatures to hdev->host_features since it
holds the extended features Page 1 (aka host features).
Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make code readable by removing magic numbers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Current controller initialization is moved tp bredr_init and new
function added amp_init to handle later AMP init sequence. Current
AMP init sequence include Reset and Read Local Version.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify function and remove fourth level of indentation.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Implement block size read function. Use different variables for
packet-based and block-based flow control.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This should simplify Bluetooth core processing a lot.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As part of the moving on all the Bluetooth processing to Process context.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It's pointless, we aren't protecting anything since btusb_notify()
schedules a work to run, then all it operation happens without protection.
If protection is really needed here, we will fix it further.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As HCI rx path is now done in process context it makes sense to do all the
timer in process context as well.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make sure that code match exactly what comment says about pre 1.2
bluetooth version. Since this is HCI detail lmp_ver changed to hci_ver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Use bluetooth names instead of BT SIG assigned numbers
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Check for hci_ver instead of lmp_ver
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds the parameter struct and the command complete event
handler to the LE Set Scan Parameter HCI command.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds the dev_flags field to struct hci_dev. This new
flags variable should be used to define flags related to BR/EDR
and/or LE controller itself. It should be used to define flags
which represents states from the controller. The dev_flags is
cleared in case the controller sends a Reset Command Complete
Event to the host.
Also, this patch adds the HCI_LE_SCAN flag which was created to
track if the controller is performing LE scan or not. The flag
is set/cleared when the controller starts/stops scanning.
This is an initial effort to stop using hdev->flags to define
internal flags since it is exported to userspace by an ioctl.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Upstream Code Aurora function with minor trivial fixes.
Origin: git://codeaurora.org/kernel/msm.git
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Some MITM scenarios require handling of the User Passkey Request event,
by querying the user, and passing the response back.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patches creates mgmt_stop_discovery_failed() which removes
pending MGMT_OP_STOP_DISCOVERY commands and sends proper command
status events.
This patch also fixes the MGMT_OP_STOP_DISCOVERY command leak in
case cancel inquiry fails.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch renames the function mgmt_inquiry_failed() to
mgmt_start_discovery_failed(). This function is more related
to MGMT_OP_START_DISCOVERY command handling than to inquiry.
Besides, this functions will be reused by LE based discovery
procedures in case of failure.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Since disconnecting may fail the status needs to be communicated to user
space. This also updates the implementation to match the latest mgmt API
specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It's necessary to know the distinction between public and random LE
addresses so the mgmt interface also needs to distinguish between them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Now that the pending commands are within struct hci_dev we can properly
control access to them throught the hci_dev locking mechanism.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The current global pending command list in mgmt.c is racy. Possibly the
simplest way to fix it is to have per-hci dev lists instead of a global
one (all commands that need a pending struct are hci_dev specific).
This way the list can be protected using the already existing per-hci
dev lock. To enable this refactoring the first thing that needs to be
done is to ensure that the mgmt functions have access to the hci_dev
struct (instead of just the dev id).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds address type info (typically BR/EDR vs LE) to management
messages that need this. This also ensures conformance to the latest
management API specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
A proper mgmt_command_status should be returned to user-space if either
discoverable or connectable enabling fails.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Based on the revised mgmt API set_discoverable has a timeout parameter
to specify how long the adapter will remain discoverable. A value of 0
means "indefinitively".
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
By using periodic inquiry command we're not able to detect correctly
when the controller has started inquiry.
Today we have this workaround in inquiry result event handler
to set the HCI_INQUIRY flag when it sees the first inquiry result
event. This workaround isn't enough because the device may be
performing an inquiry but the HCI_INQUIRY flag is not set. For
instance, if there is no device in range, no inquiry result event
is generated, consequently, the HCI_INQUIRY flags isn't set when
it should so.
We rely on HCI_INQUIRY flag to implement the discovery procedure
properly. So, as we aren't able to clear/set the HCI_INQUIRY flag
in a reliable manner, periodic inquiry events shouldn't change
the HCI_INQUIRY flag.
Thus, due to that issue and in order to keep compatibility with
userspace, periodic inquiry events shouldn't send mgmt discovering
events.
In future, we might track if periodic inquiry is enabled or not.
By tracking this state we'll be able to do some improvements in
Discovery such as failing MGMT_OP_START_DISCOVERY command in case
periodic inquiry is on. We can also send no mgmt_device_found
event if periodic inquiry is on.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a new label to hci_cc_write_scan_enable to avoid
unnecessary indentation. This will be convenient especially when new
code for the discoverable timeout gets added.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds the necessary code to send proper command status or
command complete events to the start/stop discovery management commands.
Before this patch these events were completely missing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Implementation of Read Local AMP Info Command
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
There is no reason to treat the first advertising entry differently
from the potential other ones. Besides, the current implementation
can easily leads to typos.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Checking conn->pending_sec_level if there is no connection leads to potential
null pointer dereference. Don't process pin_code_request_event at all if no
connection exists.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch reduces the critial region (protected by hdev->lock) in
hci_cc_le_set_scan_enable(). This way, only really required code is
synchronized.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The HIGH security level requires a 16 digit pin code for non-SSP
bondings. Sometimes this requirement is not acceptable and we still
want protection againts MITM attacks (which is something that the
MEDIUM security level doesn't provide), for that we should allow
another way to request authentication without using the HIGH security
level.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
One piece of information that was lost when using the mgmt interface,
was the type of the connection. Using HCI events we used to know
the type of the connection based on the type of the event, e.g.
HCI_LE_Connection_Complete for LE links.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The checks for HCI_INQUIRY and HCI_MGMT were in the wrong order,
so that second scans always failed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In some cases it will be useful having the key size used for
encrypting the link. For example, some profiles may restrict
some operations depending on the key length.
The key size is stored in the key that is passed to userspace
using the pin_length field in the key structure.
For now this field is only valid for LE controllers. 3.0+HS
controllers define the Read Encryption Key Size command, this
field is intended for storing the value returned by that
command.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Now that we have methods to finding keys by its parameters we can
reject an encryption request if the key isn't found.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a new module parameter to enable/disable host LE
support. By default host LE support is disabled.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a handler to Write LE Host Supported command complete
events. Once this commands has completed successfully, we should
read the extended LMP features and update the extfeatures field in
hci_dev.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This new field holds the extended LMP features value. Some LE
mechanism such as discovery procedure needs to read the extended
LMP features to work properly.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch implements a simple version of the SMP Pairing Features
exchange procedure (Vol. 3 Part H, Section 2.3.5.1).
For now, everything that would cause a Pairing Method different of
Just Works to be chosen is rejected.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As the default security level (BT_SECURITY_SDP) doesn't make sense for
LE links, initialize LE links with something that makes sense.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This adds support for starting SMP Phase 2 Encryption, when the initial
SMP negotiation is successful. This adds the LE Start Encryption and LE
Long Term Key Request commands and related events.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Some old hci controllers do not accept any mask so leave the
default mask on for these devices.
< HCI Command: Set Event Mask (0x03|0x0001) plen 8
Mask: 0xfffffbff00000000
> HCI Event: Command Complete (0x0e) plen 4
Set Event Mask (0x03|0x0001) ncmd 1
status 0x12
Error: Invalid HCI Command Parameters
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Tested-by: Corey Boyle <corey@kansanian.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a new field (dst_type) to the struct hci_conn which
holds the type of the destination address (bdaddr_t dst). This
approach is needed in order to use the struct hci_conn as an
abstraction of LE connections in HCI Layer. For non-LE this field
is ignored.
This patch also set properly the 'dst_type' field after initializing
LE hci_conn structures.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Replace if(conn) with if(!conn) checking to avoid too many nested statements
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Legacy devices don't re-authenticate the link properly if a link key
already exists. Thus, don't update sec_level for this case even if
hci_auth_complete_evt indicates success. Otherwise the sec_level will
not reflect a real security on the link.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a timer to clear 'adv_entries' after three minutes.
After some amount of time, the advertising entries cached during
the last LE scan should be considered expired and they should be
removed from the advertising cache.
It was chosen a three minutes timeout as an initial attempt. This
value might change in future.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The LE advertising cache should be cleared before performing a LE
scanning. This will force the cache to contain only fresh advertising
entries.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a function to handle LE Advertising Report Meta
Events.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We need to be able for receive events notifying that the connection
was established, the connection attempt failed or that disconnection
happened.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In some circumstances hci_get_auth_req will return a value different
from the current conn->auth_type. In these cases update conn->auth_type
so that when a user confirm request comes it doesn't falsely trigger
auto-accept.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Link keys should only be stored if very specific criteria of the
authentication process are fulfilled. This patch essentially copies the
criteria that user space has so far been using to the kernel side so
that the management interface works properly.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The mgmt_ev_pin_code_request event should not be sent to user space if
the request gets rejected by the kernel due to the pairable flag not
being set.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
"Pairing not allowed" is 0x18 and not 0x16.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When accepting a pairing request which fulfills the SSP auto-accept
criteria we need to push the request all the way to the user for
confirmation. This patch adds a new hint to the user_confirm_request
management event so user space can know when to show a numeric
comparison dialog and when to show a simple yes/no confirmation dialog.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The HCI_CONN_AUTH_PEND flag should be set whenever requesting
authentication so that multiple pending requests can't occur.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Some test systems require an arbitrary delay to the auto-accept test
cases for Secure Simple Pairing in order for the tests to pass.
Previously when this was handled in user space it was worked around by
code modifications and recompilation, but now that it's on the kernel
side it's more convenient if there's a debugfs interface for it.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds automated negative and positive (auto-accept) responses
for Secure Simple Pairing user confirmation requests. The responses are
only sent if the HCI_MGMT flag is set in order not to confuse older user
space versions (without management interface support).
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Extend the mgmt_pin_code_request interface to require secure
pin code (16 digit) for authentication.
This is a kernel part of the secure pin code requirement notification
to user space agent.
Code styling fix by Johan Hedberg.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If host requires MITM protection notify that to controller in
io capabilities reply even if the remote device requires no bonding.
If it is not respected, host can get an unauthenticated link key while
it expects authenticated one.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
High security level for pre v2.1 devices requires combination link key
authenticated by at least 16 digit PIN code.
It's also necessary to update key_type and pin_length when the key
exists and is sufficently secured for the connection as there will be
no link key notify event in that case.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Keep the link key type together with connection and use it to
map security level to link key requirements. Authenticate and/or
encrypt connection if the link is insufficiently secure.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If authentication fails the security level should stay as it was set
before the process has started. Setting BT_SECURITY_LOW can hide real
security level on a link eg. having BT_SECURITY_MEDIUM on the link,
re-authenticate with failure to get BT_SECURITY_HIGH, as a result we
get BT_SECURITY_LOW on the link while the real security is still medium.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Introduce the link key types defs and use them instead of magic numbers.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a new event to the Management interface to track when
local adapters are discovering remote devices. For now this only tracks
BR/EDR discovery procedures.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
hci_io_capa_reply_evt() holds reference for hciconnection. It's useless since
hci_io_capa_request_evt()/hci_simple_pair_complete_evt() already protects the
connection. In addition it leaves connection open after failed SSP pairing.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Use kernel stored remote Out Of Band data only if management interface
is enabled. Otherwise HCI_OP_REMOTE_OOB_DATA_NEG_REPLY was sent to
controller even if remote Out Of Band data was present in bluetoothd.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a new remote_name event to the Management interface
which is sent every time the name of a remote device is resolved (over
BR/EDR).
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a device_found event to the Management interface. For
now the event only maps to BR/EDR inquiry result HCI events, but in the
future the plan is to also use it for the LE device discovery process.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We can't send new commands before a cmd_complete for the HCI_RESET command
shows up.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Reported-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
If remote side reports oob availability or we are pairing initiator
use oob data for pairing if available.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds commands to add and remove remote OOB data to the managment
interface. Remote data is stored in kernel and can be used by corresponding
HCI commands and events when needed.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a command to read local OOB data to the managment interface.
The command maps directly to the Read Local OOB Data HCI command.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a new set_local_name management command as well as a
local_name_changed management event. With these user space can both
change the local name as well as monitor changes to it by others.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a clear define for the maximum device name length in HCI
messages and thereby avoids magic numbers in the code.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We can't send new commands before a cmd_complete for the HCI_RESET command
shows up.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Reported-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
To properly track bonding completion an event to indicate authentication
failure is needed. This event will be sent whenever an authentication
complete HCI event with a non-zero status comes. It will also be sent
when we're acting in acceptor role for SSP authentication in which case
the controller will send a Simple Pairing Complete event.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds support for the user confirmation (numeric comparison)
Secure Simple Pairing authentication method.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Use proper timer instead of hci command flow control to timeout
failed hci commands. Otherwise stack ends up sending commands
when flow control is used to block new commands.
2010-09-01 18:29:41.592132 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:16:CF:E1:C7:D7 mode 2 clkoffset 0x0000
2010-09-01 18:29:41.592681 > HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 0
2010-09-01 18:29:51.022033 < HCI Command: Remote Name Request Cancel (0x01|0x001a) plen 6
bdaddr 00:16:CF:E1:C7:D7
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add support for LE server sockets.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth chips may have separate buffers for LE traffic.
This patch add support to use LE buffers provided by the chip.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth V4.0 adds support for Low Energy (LE) connections.
Specification introduces new set of hci commands to control LE
connection. This patch adds logic to create, cancel and disconnect
LE connections.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fix checkpatch warnings concerning assignments in if conditions.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a new set_io_capability management command which is used
to set the IO capability for Secure Simple Pairing (SSP) as well as the
Security Manager Protocol (SMP). The value is per hci_dev and each
hci_conn object inherits it upon creation.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds the necessary commands and events needed to communicate
PIN code related actions between the kernel and userspace. This includes
a pin_code_request event as well as pin_code_reply and
pin_code_negative_reply commands.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch add a new connect failed management event to track failures
in connecting to remote devices. It is particularly useful for security
mode 3 scenarios when we don't have a connected state while pairing but
still need to detect when the connect attempt failed.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a disconnect command to the managment interface. Using
this command user space is able to force the disconnection of connected
devices. The command maps directly to the Disconnect HCI command.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds connected and disconnected managment events to track the
connection status to remote devices. The events map directly to
successful connection complete and disconnection complete HCI events for
ACL links.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a management commands to feed the kernel with all stored
link keys as well as remove specific ones or all of them. Once the
load_keys command has been called the kernel takes over link key
replies. A new_key event is also added to inform userspace of newly
created link keys that should be stored permanently.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Using the managment interface means that user space doesn't need to do
any HCI command sending at all. This patch moves the remaining
initialization commands from user space to the kernel side. The patch
makes use of the new feature of __hci_request which allows the request
to be dynamically modified while it is ongoing (something that is needed
to react appropriately to the local features and the version of the
adapter).
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The controller may have link keys in its own memory and these keys could
be used for secure connections. However, since the interface to access
these keys doesn't provide information about the key types (which would
be needed to infer the level of security each key provides) using these
keys is rather useless. Therefore, simply clear the controller side list
in the initialization procedure.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds the necessary logic to act accordingly when the
HCI_PAIRABLE flag is not set. In that case PIN code replies as well as
Secure Simple Pairing requests without a NoBonding requirement need to
be rejected.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a set_connectable command as well as a corresponding
event to the management interface. It's mainly useful for setting an
adapter as connectable from a non-initialized state as well as setting
an already initialized adapter as non-connectable (mostly useful for
qualification purposes).
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a set_discoverable command to the management interface
as well as the corresponding event. The command is used to control the
discoverable state of adapters.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a set_powered command to the management interface
through which the powered state of local adapters can be controlled.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The conn->sec_level value is supposed to represent the current level of
security that the connection has. However, by assigning to it before
requesting authentication it will have the wrong value during the
authentication procedure. To fix this a pending_sec_level variable is
added which is used to track the desired security level while making
sure that sec_level always represents the current level of security.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The initialization function used by hci_open_dev (hci_init_req) sends
many different HCI commands. The __hci_request function should only
return when all of these commands have completed (or a timeout occurs).
Several of these commands cause hci_req_complete to be called which
causes __hci_request to return prematurely.
This patch fixes the issue by adding a new hdev->req_last_cmd variable
which is set during the initialization procedure. The hci_req_complete
function will no longer mark the request as complete until the command
matching hdev->req_last_cmd completes.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Do not use assignment in IF condition, remove extra spaces,
fixing typos, simplify code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fix checkpatch errors like:
"ERROR: do not use assignment in if condition"
Simplify code and fix one long line.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In Bluetooth there are no automatic updates of remote device names when
they get changed on the remote side. Instead, it is a good idea to do a
manual name request when a new connection gets created (for whatever
reason) since at this point it is very cheap (no costly baseband
connection creation needed just for the sake of the name request).
So far userspace has been responsible for this extra name request but
tighter control is needed in order not to flood Bluetooth controllers
with two many commands during connection creation. It has been shown
that some controllers simply fail to function correctly if they get too
many (almost) simultaneous commands during connection creation. The
simplest way to acheive better control of these commands is to move
their sending completely to the kernel side.
This patch inserts name requests into the sequence of events that the
kernel performs during connection creation. It does this after the
remote features have been successfully requested and before any pending
authentication requests are performed. The code will work sub-optimally
with userspace versions that still do the name requesting themselves (it
shouldn't break anything though) so it is recommended to combine this
with a userspace software version that doesn't have automated name
requests.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a single function that's responsible for requesting
authentication for outgoing connections. This is preparation for the
next patch which will add automated name requests and thereby move the
authentication requests to a different location.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The current remote and remote extended features event callbacks logic
can be made simpler by using a label and goto statements instead of the
current multiple levels of nested if statements.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When initiating dedicated bonding a L2CAP raw socket with HIGH security
level is used. The kernel is supposed to trigger the authentication
request in this case but this doesn't happen currently for non-SSP
(pre-2.1) devices. The reason is that the authentication request happens
in the remote extended features callback which never gets called for
non-SSP devices. This patch fixes the issue by requesting also
authentiation in the (normal) remote features callback in the case of
non-SSP devices.
This rule is applied only for HIGH security level which might at first
seem unintuitive since on the server socket side MEDIUM is already
enough for authentication. However, for the clients we really want to
prefer the server side to decide the authentication requrement in most
cases, and since most client sockets use MEDIUM it's better to be
avoided on the kernel side for these sockets. The important socket to
request it for is the dedicated bonding one and that socket uses HIGH
security level.
The patch is based on the initial investigation and patch proposal from
Andrei Emeltchenko <endrei.emeltchenko@nokia.com>.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Qualcomm, Inc. has reassigned rights to Code Aurora Forum. Accordingly,
as files are modified by Code Aurora Forum members, the copyright
statement will be updated.
Signed-off-by: Ron Shaffer <rshaffer@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances it could be desirable to reject incoming
connections on the baseband level. This patch adds this feature through
two new ioctl's: HCIBLOCKADDR and HCIUNBLOCKADDR. Both take a simple
Bluetooth address as a parameter. BDADDR_ANY can be used with
HCIUNBLOCKADDR to remove all devices from the blacklist.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When authentication fails for a connection the assumed security level
should be set back to BT_SECURITY_LOW so that subsequent connect
attempts over the same link don't falsely assume that security is
adequate enough.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The tasklet schedule function helpers are just an obfuscation. So remove
them and call the schedule functions directly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device model itself has no real usable reference counting at the
moment and this causes problems if parents are deleted before their
children. The device model itself handles the memory details of this
correctly, but the uevent order is not consistent. This causes various
problems for systems like HAL or even X.
So until device_put() does a proper cleanup, the device for Bluetooth
connection will be protected with an extra reference counting to ensure
the correct order of uevents when connections are terminated.
This is not an automatic feature. Higher Bluetooth layers like HIDP or
BNEP should grab this new reference to ensure that their uevents are
send before the ones from the parent device.
Based on a report by Brian Rogers <brian@xyzw.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A remote device in security mode 3 that tries to connect will require
the pairing during the connection setup phase. The disconnect timeout
is now triggered within 10 milliseconds and causes the pairing to fail.
If a connection is not fully established and a PIN code request is
received, don't trigger the disconnect timeout. The either successful
or failing connection complete event will make sure that the timeout
is triggered at the right time.
The biggest problem with security mode 3 is that many Bluetooth 2.0
device and before use a temporary security mode 3 for dedicated
bonding.
Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Johan Hedberg <johan.hedberg@nokia.com>
The Bluetooth stack uses a reference counting for all established ACL
links and if no user (L2CAP connection) is present, the link will be
terminated to save power. The problem part is the dedicated pairing
when using Legacy Pairing (Bluetooth 2.0 and before). At that point
no user is present and pairing attempts will be disconnected within
10 seconds or less. In previous kernel version this was not a problem
since the disconnect timeout wasn't triggered on incoming connections
for the first time. However this caused issues with broken host stacks
that kept the connections around after dedicated pairing. When the
support for Simple Pairing got added, the link establishment procedure
needed to be changed and now causes issues when using Legacy Pairing
When using Simple Pairing it is possible to do a proper reference
counting of ACL link users. With Legacy Pairing this is not possible
since the specification is unclear in some areas and too many broken
Bluetooth devices have already been deployed. So instead of trying to
deal with all the broken devices, a special pairing timeout will be
introduced that increases the timeout to 60 seconds when pairing is
triggered.
If a broken devices now puts the stack into an unforeseen state, the
worst that happens is the disconnect timeout triggers after 120 seconds
instead of 4 seconds. This allows successful pairings with legacy and
broken devices now.
Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom chips with 2.1 firmware handle the fallback case to a SCO
link wrongly when setting up eSCO connections.
< HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
handle 11 voice setting 0x0060
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
status 0x00 handle 1 bdaddr 00:1E:3A:xx:xx:xx type SCO encrypt 0x01
The Link Manager negotiates the fallback to SCO, but then sends out
a Connect Complete event. This is wrong and the Link Manager should
actually send a Synchronous Connection Complete event if the Setup
Synchronous Connection has been used. Only the remote side is allowed
to use Connect Complete to indicate the missing support for eSCO in
the host stack.
This patch adds a workaround for this which clearly should not be
needed, but reality is that broken Broadcom devices are deployed.
Based on a report by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtman <marcel@holtmann.org>
Some Bluetooth chips (like the ones from Texas Instruments) don't do
proper eSCO negotiations inside the Link Manager. They just return an
error code and in case of the Kyocera ED-8800 headset it is just a
random error.
< HCI Command: Setup Synchronous Connection 0x01|0x0028) plen 17
handle 1 voice setting 0x0060
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
status 0x1f handle 257 bdaddr 00:14:0A:xx:xx:xx type eSCO
Error: Unspecified Error
In these cases it is up to the host stack to fallback to a SCO setup
and so retry with SCO parameters.
Based on a report by Nick Pelly <npelly@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some of the qualification tests demand that in case of failures in L2CAP
the HCI disconnect should indicate a reason why L2CAP fails. This is a
bluntly layer violation since multiple L2CAP connections could be using
the same ACL and thus forcing a disconnect reason is not a good idea.
To comply with the Bluetooth test specification, the disconnect reason
is now stored in the L2CAP connection structure and every time a new
L2CAP channel is added it will set back to its default. So only in the
case where the L2CAP channel with the disconnect reason is really the
last one, it will propagated to the HCI layer.
The HCI layer has been extended with a disconnect indication that allows
it to ask upper layers for a disconnect reason. The upper layer must not
support this callback and in that case it will nicely default to the
existing behavior. If an upper layer like L2CAP can provide a disconnect
reason that one will be used to disconnect the ACL or SCO link.
No modification to the ACL disconnect timeout have been made. So in case
of Linux to Linux connection the initiator will disconnect the ACL link
before the acceptor side can signal the specific disconnect reason. That
is perfectly fine since Linux doesn't make use of this value anyway. The
L2CAP layer has a perfect valid error code for rejecting connection due
to a security violation. It is unclear why the Bluetooth specification
insists on having specific HCI disconnect reason.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When attempting to setup eSCO connections it can happen that some link
manager implementations fail to properly negotiate the eSCO parameters
and thus fail the eSCO setup. Normally the link manager is responsible
for the negotiation of the parameters and actually fallback to SCO if
no agreement can be reached. In cases where the link manager is just too
stupid, then at least try to establish a SCO link if eSCO fails.
For the Bluetooth devices with EDR support this includes handling packet
types of EDR basebands. This is particular tricky since for the EDR the
logic of enabling/disabling one specific packet type is turned around.
This fix contains an extra bitmask to disable eSCO EDR packet when
trying to fallback to a SCO connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current security model is based around the flags AUTH, ENCRYPT and
SECURE. Starting with support for the Bluetooth 2.1 specification this is
no longer sufficient. The different security levels are now defined as
SDP, LOW, MEDIUM and SECURE.
Previously it was possible to set each security independently, but this
actually doesn't make a lot of sense. For Bluetooth the encryption depends
on a previous successful authentication. Also you can only update your
existing link key if you successfully created at least one before. And of
course the update of link keys without having proper encryption in place
is a security issue.
The new security levels from the Bluetooth 2.1 specification are now
used internally. All old settings are mapped to the new values and this
way it ensures that old applications still work. The only limitation
is that it is no longer possible to set authentication without also
enabling encryption. No application should have done this anyway since
this is actually a security issue. Without encryption the integrity of
the authentication can't be guaranteed.
As default for a new L2CAP or RFCOMM connection, the LOW security level
is used. The only exception here are the service discovery sessions on
PSM 1 where SDP level is used. To have similar security strength as with
a Bluetooth 2.0 and before combination key, the MEDIUM level should be
used. This is according to the Bluetooth specification. The MEDIUM level
will not require any kind of man-in-the-middle (MITM) protection. Only
the HIGH security level will require this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the remote device supports only SCO connections, on receipt of
the HCI_EV_CONN_COMPLETE event packet, the connect state is changed to
BT_CONNECTED, but the socket state is not updated. Hence, the connect()
call times out even though the SCO connection has been successfully
established.
Based on a report by Jaikumar Ganesh <jaikumar@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to
allow debugging without having to recompile the kernel. This patch turns
all BT_DBG() calls into pr_debug() to support dynamic debug messages.
As a side effect all CONFIG_BT_*_DEBUG statements are now removed and
some broken debug entries have been fixed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ACL config stage keeps holding a reference count on incoming
connections when requesting the extended features. This results in
keeping an ACL link up without any users. The problem here is that
the Bluetooth specification doesn't define an ownership of the ACL
link and thus it can happen that the implementation on the initiator
side doesn't care about disconnecting unused links. In this case the
acceptor needs to take care of this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When attaching Bluetooth low-level connections to the bus, the bus name
is constructed from the remote address since at that time the connection
handle is not assigned yet. This has worked so far, but also caused a
lot of troubles. It is better to postpone the creation of the sysfs
entry to the time when the connection actually has been established
and then use its connection handle as unique identifier.
This also fixes the case where two different adapters try to connect
to the same remote device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With Bluetooth 2.1 and Simple Pairing the requirement is that any new
connection needs to be authenticated and that encryption has been
switched on before allowing L2CAP to use it. So make sure that all
the requirements are fulfilled and otherwise drop the connection with
a minimal disconnect timeout of 10 milliseconds.
This change only affects Bluetooth 2.1 devices and Simple Pairing
needs to be enabled locally and in the remote host stack. The previous
changes made sure that these information are discovered before any
kind of authentication and encryption is triggered.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth technology introduces new features on a regular basis
and for some of them it is important that the hardware on both sides
support them. For features like Simple Pairing it is important that
the host stacks on both sides have switched this feature on. To make
valid decisions, a config stage during ACL link establishment has been
introduced that retrieves remote features and if needed also the remote
extended features (known as remote host features) before signalling
this link as connected.
This change introduces full reference counting of incoming and outgoing
ACL links and the Bluetooth core will disconnect both if no owner of it
is present. To better handle interoperability during the pairing phase
the disconnect timeout for incoming connections has been increased to
10 seconds. This is five times more than for outgoing connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Simple Pairing process can only be used if both sides have the
support enabled in the host stack. The current Bluetooth specification
has three ways to detect this support.
If an Extended Inquiry Result has been sent during inquiry then it
is safe to assume that Simple Pairing is enabled. It is not allowed
to enable Extended Inquiry without Simple Pairing. During the remote
name request phase a notification with the remote host supported
features will be sent to indicate Simple Pairing support. Also the
second page of the remote extended features can indicate support for
Simple Pairing.
For all three cases the value of remote Simple Pairing mode is stored
in the inquiry cache for later use.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Simple Pairing feature is optional and needs to be enabled by the
host stack first. The Linux kernel relies on the Bluetooth daemon to
either enable or disable it, but at any time it needs to know the
current state of the Simple Pairing mode. So track any changes made
by external entities and store the current mode in the HCI device
structure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During the Simple Pairing process the HCI disconnect timer must be
disabled. The way to do this is by holding a reference count of the
HCI connection. The Simple Pairing process on both sides starts with
an IO Capabilities Request and ends with Simple Pairing Complete.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The class of device value can only be retrieved via inquiry or during
an incoming connection request. Outgoing connections can't ask for the
class of device. To compensate for this the value is stored and copied
via the inquiry cache, but currently only updated via inquiry. This
update should also happen during an incoming connection request.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some minor cosmetic cleanups to the HCI event handling to make the
code easier to read and understand.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth specification supports the default link policy settings
on a per host controller basis. For every new connection the link
manager would then use these settings. It is better to use this instead
of bothering the controller on every connection setup to overwrite the
default settings.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The connection packet type can be changed after the connection has been
established and thus needs to be properly tracked to ensure that the
host stack has always correct and valid information about it.
On incoming connections the Bluetooth core switches the supported packet
types to the configured list for this controller. However the usefulness
of this feature has been questioned a lot. The general consent is that
every Bluetooth host stack should enable as many packet types as the
hardware actually supports and leave the decision to the link manager
software running on the Bluetooth chip.
When running on Bluetooth 2.0 or later hardware, don't change the packet
type for incoming connections anymore. This hardware likely supports
Enhanced Data Rate and thus leave it completely up to the link manager
to pick the best packet type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When trying to establish an eSCO link between two devices then it can
happen that the remote device falls back to a SCO link. Currently this
case is not handled correctly and the message dispatching will break
since it is looking for eSCO packets. So in case the configured link
falls back to SCO overwrite the link type with the correct value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The authentication status is not communicated to both parties. This is
actually a flaw in the Bluetooth specification. Only the requesting side
really knows if the authentication was successful or not. This piece of
information is however needed on the other side to know if it has to
trigger the authentication procedure or not. Worst case is that both
sides will request authentication at different times, but this should
be avoided since it costs extra time when setting up a new connection.
For Bluetooth encryption it is required to authenticate the link first
and the encryption status is communicated to both sides. So when a link
is switched to encryption it is possible to update the authentication
status since it implies an authenticated link.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the Bluetooth 1.2 specification the Extended SCO feature for
better audio connections was introduced. So far the Bluetooth core
wasn't able to handle any eSCO connections correctly. This patch
adds simple eSCO support while keeping backward compatibility with
older devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth HCI commands are divided into logical OGF groups for
easier identification of their purposes. While this still makes sense
for the written specification, its makes the code only more complex
and harder to read. So instead of using separate OGF and OCF values
to identify the commands, use a common 16-bit opcode that combines
both values. As a side effect this also reduces the complexity of
OGF and OCF calculations during command header parsing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To better support and handle eSCO links in the future a bunch of
constants needs to be added and some basic routines need to be
updated. This is the initial step.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After an inquiry completed or got canceled the Bluetooth core should
check for any pending connect attempts.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Most Bluetooth chips don't support concurrent connect requests, because
this would involve a multiple baseband page with only one radio. In the
case an upper layer like L2CAP requests a concurrent connect these chips
return the error "Command Disallowed" for the second request. If this
happens it the responsibility of the Bluetooth core to queue the request
and try again after the previous connect attempt has been completed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the case of device pairing the only safe method is to establish
a low-level ACL link. In this case, the remote side should not use
the disconnect timer to give the other side the chance to enter the
PIN code. If the disconnect timer is used, the connection will be
dropped to soon, because it is impossible to identify an actual user
of this link.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of non-blocking connects it is possible that the last user
of an ACL link quits before the connection has been fully established.
This will lead to a race condition where the internal state of a
connection is closed, but the actual link has been established and is
active. In case of Bluetooth 1.2 and later devices it is possible to
call create connection cancel to abort the connect. For older devices
the disconnect timer will be used to trigger the needed disconnect.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The local version information are needed to identify certain feature
sets of devices. They must be read on device init and stored for later
use. It is also possible to access them through the device model.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The command complete event of the exit periodic inquiry command must
clear the HCI_INQUIRY flag and finish the HCI request.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the automatic sniff mode feature. This allows
the host to switch idle connections into sniff mode to safe power.
Signed-off-by: Ulisses Furquim <ulissesf@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces a quirk that allows the drivers to tell the host
to correct the SCO buffer size values.
Signed-off-by: Olivier Galibert <galibert@pobox.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the endian annotations to the Bluetooth core.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the handling of the extended inquiry responses and
inserts them into the inquiry cache.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the usage of packet type into the SKB control
buffer. After this patch it is now possible to shrink the sk_buff
structure and redefine its pkt_type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HCI page scan repetition mode change event contains the actual
page scan repetition mode for the remote device. It is the same
value that is received from an inquiry response and it can be used
to make further reconnections faster.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements a workaround for buggy Bluetooth 1.2 devices from
Silicon Wave. Their inquiry results with RSSI contain the page scan mode
field. This field was removed in the final Bluetooth 1.2 specification.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unused bt_dump() function and it also removes
its BT_DMP macro. It also unexports the hci_dev_get(), hci_send_cmd()
and hci_si_event() functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A lot of places in there are including major.h for no reason whatsoever.
Removed. And yes, it still builds.
The history of that stuff is often amusing. E.g. for net/core/sock.c
the story looks so, as far as I've been able to reconstruct it: we used
to need major.h in net/socket.c circa 1.1.early. In 1.1.13 that need
had disappeared, along with register_chrdev(SOCKET_MAJOR, "socket",
&net_fops) in sock_init(). Include had not. When 1.2 -> 1.3 reorg of
net/* had moved a lot of stuff from net/socket.c to net/core/sock.c,
this crap had followed...
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!