This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Merge first patchbomb from Andrew Morton:
- a few minor cifs fixes
- dma-debug upadtes
- ocfs2
- slab
- about half of MM
- procfs
- kernel/exit.c
- panic.c tweaks
- printk upates
- lib/ updates
- checkpatch updates
- fs/binfmt updates
- the drivers/rtc tree
- nilfs
- kmod fixes
- more kernel/exit.c
- various other misc tweaks and fixes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
exit: pidns: fix/update the comments in zap_pid_ns_processes()
exit: pidns: alloc_pid() leaks pid_namespace if child_reaper is exiting
exit: exit_notify: re-use "dead" list to autoreap current
exit: reparent: call forget_original_parent() under tasklist_lock
exit: reparent: avoid find_new_reaper() if no children
exit: reparent: introduce find_alive_thread()
exit: reparent: introduce find_child_reaper()
exit: reparent: document the ->has_child_subreaper checks
exit: reparent: s/while_each_thread/for_each_thread/ in find_new_reaper()
exit: reparent: fix the cross-namespace PR_SET_CHILD_SUBREAPER reparenting
exit: reparent: fix the dead-parent PR_SET_CHILD_SUBREAPER reparenting
exit: proc: don't try to flush /proc/tgid/task/tgid
exit: release_task: fix the comment about group leader accounting
exit: wait: drop tasklist_lock before psig->c* accounting
exit: wait: don't use zombie->real_parent
exit: wait: cleanup the ptrace_reparented() checks
usermodehelper: kill the kmod_thread_locker logic
usermodehelper: don't use CLONE_VFORK for ____call_usermodehelper()
fs/hfs/catalog.c: fix comparison bug in hfs_cat_keycmp
nilfs2: fix the nilfs_iget() vs. nilfs_new_inode() races
...
Memory is internally accounted in bytes, using spinlock-protected 64-bit
counters, even though the smallest accounting delta is a page. The
counter interface is also convoluted and does too many things.
Introduce a new lockless word-sized page counter API, then change all
memory accounting over to it. The translation from and to bytes then only
happens when interfacing with userspace.
The removed locking overhead is noticable when scaling beyond the per-cpu
charge caches - on a 4-socket machine with 144-threads, the following test
shows the performance differences of 288 memcgs concurrently running a
page fault benchmark:
vanilla:
18631648.500498 task-clock (msec) # 140.643 CPUs utilized ( +- 0.33% )
1,380,638 context-switches # 0.074 K/sec ( +- 0.75% )
24,390 cpu-migrations # 0.001 K/sec ( +- 8.44% )
1,843,305,768 page-faults # 0.099 M/sec ( +- 0.00% )
50,134,994,088,218 cycles # 2.691 GHz ( +- 0.33% )
<not supported> stalled-cycles-frontend
<not supported> stalled-cycles-backend
8,049,712,224,651 instructions # 0.16 insns per cycle ( +- 0.04% )
1,586,970,584,979 branches # 85.176 M/sec ( +- 0.05% )
1,724,989,949 branch-misses # 0.11% of all branches ( +- 0.48% )
132.474343877 seconds time elapsed ( +- 0.21% )
lockless:
12195979.037525 task-clock (msec) # 133.480 CPUs utilized ( +- 0.18% )
832,850 context-switches # 0.068 K/sec ( +- 0.54% )
15,624 cpu-migrations # 0.001 K/sec ( +- 10.17% )
1,843,304,774 page-faults # 0.151 M/sec ( +- 0.00% )
32,811,216,801,141 cycles # 2.690 GHz ( +- 0.18% )
<not supported> stalled-cycles-frontend
<not supported> stalled-cycles-backend
9,999,265,091,727 instructions # 0.30 insns per cycle ( +- 0.10% )
2,076,759,325,203 branches # 170.282 M/sec ( +- 0.12% )
1,656,917,214 branch-misses # 0.08% of all branches ( +- 0.55% )
91.369330729 seconds time elapsed ( +- 0.45% )
On top of improved scalability, this also gets rid of the icky long long
types in the very heart of memcg, which is great for 32 bit and also makes
the code a lot more readable.
Notable differences between the old and new API:
- res_counter_charge() and res_counter_charge_nofail() become
page_counter_try_charge() and page_counter_charge() resp. to match
the more common kernel naming scheme of try_do()/do()
- res_counter_uncharge_until() is only ever used to cancel a local
counter and never to uncharge bigger segments of a hierarchy, so
it's replaced by the simpler page_counter_cancel()
- res_counter_set_limit() is replaced by page_counter_limit(), which
expects its callers to serialize against themselves
- res_counter_memparse_write_strategy() is replaced by
page_counter_limit(), which rounds down to the nearest page size -
rather than up. This is more reasonable for explicitely requested
hard upper limits.
- to keep charging light-weight, page_counter_try_charge() charges
speculatively, only to roll back if the result exceeds the limit.
Because of this, a failing bigger charge can temporarily lock out
smaller charges that would otherwise succeed. The error is bounded
to the difference between the smallest and the biggest possible
charge size, so for memcg, this means that a failing THP charge can
send base page charges into reclaim upto 2MB (4MB) before the limit
would have been reached. This should be acceptable.
[akpm@linux-foundation.org: add includes for WARN_ON_ONCE and memparse]
[akpm@linux-foundation.org: add includes for WARN_ON_ONCE, memparse, strncmp, and PAGE_SIZE]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull VFS changes from Al Viro:
"First pile out of several (there _definitely_ will be more). Stuff in
this one:
- unification of d_splice_alias()/d_materialize_unique()
- iov_iter rewrite
- killing a bunch of ->f_path.dentry users (and f_dentry macro).
Getting that completed will make life much simpler for
unionmount/overlayfs, since then we'll be able to limit the places
sensitive to file _dentry_ to reasonably few. Which allows to have
file_inode(file) pointing to inode in a covered layer, with dentry
pointing to (negative) dentry in union one.
Still not complete, but much closer now.
- crapectomy in lustre (dead code removal, mostly)
- "let's make seq_printf return nothing" preparations
- assorted cleanups and fixes
There _definitely_ will be more piles"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
copy_from_iter_nocache()
new helper: iov_iter_kvec()
csum_and_copy_..._iter()
iov_iter.c: handle ITER_KVEC directly
iov_iter.c: convert copy_to_iter() to iterate_and_advance
iov_iter.c: convert copy_from_iter() to iterate_and_advance
iov_iter.c: get rid of bvec_copy_page_{to,from}_iter()
iov_iter.c: convert iov_iter_zero() to iterate_and_advance
iov_iter.c: convert iov_iter_get_pages_alloc() to iterate_all_kinds
iov_iter.c: convert iov_iter_get_pages() to iterate_all_kinds
iov_iter.c: convert iov_iter_npages() to iterate_all_kinds
iov_iter.c: iterate_and_advance
iov_iter.c: macros for iterating over iov_iter
kill f_dentry macro
dcache: fix kmemcheck warning in switch_names
new helper: audit_file()
nfsd_vfs_write(): use file_inode()
ncpfs: use file_inode()
kill f_dentry uses
lockd: get rid of ->f_path.dentry->d_sb
...
Highlights include:
Features:
- NFSv4.2 client support for hole punching and preallocation.
- Further RPC/RDMA client improvements.
- Add more RPC transport debugging tracepoints.
- Add RPC debugging tools in debugfs.
Bugfixes:
- Stable fix for layoutget error handling
- Fix a change in COMMIT behaviour resulting from the recent io code updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wOP3
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.19-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Features:
- NFSv4.2 client support for hole punching and preallocation.
- Further RPC/RDMA client improvements.
- Add more RPC transport debugging tracepoints.
- Add RPC debugging tools in debugfs.
Bugfixes:
- Stable fix for layoutget error handling
- Fix a change in COMMIT behaviour resulting from the recent io code
updates"
* tag 'nfs-for-3.19-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (28 commits)
sunrpc: add a debugfs rpc_xprt directory with an info file in it
sunrpc: add debugfs file for displaying client rpc_task queue
nfs: Add DEALLOCATE support
nfs: Add ALLOCATE support
NFS: Clean up nfs4_init_callback()
NFS: SETCLIENTID XDR buffer sizes are incorrect
SUNRPC: serialize iostats updates
xprtrdma: Display async errors
xprtrdma: Enable pad optimization
xprtrdma: Re-write rpcrdma_flush_cqs()
xprtrdma: Refactor tasklet scheduling
xprtrdma: unmap all FMRs during transport disconnect
xprtrdma: Cap req_cqinit
xprtrdma: Return an errno from rpcrdma_register_external()
nfs: define nfs_inc_fscache_stats and using it as possible
nfs: replace nfs_add_stats with nfs_inc_stats when add one
NFS: Deletion of unnecessary checks before the function call "nfs_put_client"
sunrpc: eliminate RPC_TRACEPOINTS
sunrpc: eliminate RPC_DEBUG
lockd: eliminate LOCKD_DEBUG
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle are:
- 'Nested Sleep Debugging', activated when CONFIG_DEBUG_ATOMIC_SLEEP=y.
This instruments might_sleep() checks to catch places that nest
blocking primitives - such as mutex usage in a wait loop. Such
bugs can result in hard to debug races/hangs.
Another category of invalid nesting that this facility will detect
is the calling of blocking functions from within schedule() ->
sched_submit_work() -> blk_schedule_flush_plug().
There's some potential for false positives (if secondary blocking
primitives themselves are not ready yet for this facility), but the
kernel will warn once about such bugs per bootup, so the warning
isn't much of a nuisance.
This feature comes with a number of fixes, for problems uncovered
with it, so no messages are expected normally.
- Another round of sched/numa optimizations and refinements, for
CONFIG_NUMA_BALANCING=y.
- Another round of sched/dl fixes and refinements.
Plus various smaller fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched: Add missing rcu protection to wake_up_all_idle_cpus
sched/deadline: Introduce start_hrtick_dl() for !CONFIG_SCHED_HRTICK
sched/numa: Init numa balancing fields of init_task
sched/deadline: Remove unnecessary definitions in cpudeadline.h
sched/cpupri: Remove unnecessary definitions in cpupri.h
sched/deadline: Fix rq->dl.pushable_tasks bug in push_dl_task()
sched/fair: Fix stale overloaded status in the busiest group finding logic
sched: Move p->nr_cpus_allowed check to select_task_rq()
sched/completion: Document when to use wait_for_completion_io_*()
sched: Update comments about CLONE_NEWUTS and CLONE_NEWIPC
sched/fair: Kill task_struct::numa_entry and numa_group::task_list
sched: Refactor task_struct to use numa_faults instead of numa_* pointers
sched/deadline: Don't check CONFIG_SMP in switched_from_dl()
sched/deadline: Reschedule from switched_from_dl() after a successful pull
sched/deadline: Push task away if the deadline is equal to curr during wakeup
sched/deadline: Add deadline rq status print
sched/deadline: Fix artificial overrun introduced by yield_task_dl()
sched/rt: Clean up check_preempt_equal_prio()
sched/core: Use dl_bw_of() under rcu_read_lock_sched()
sched: Check if we got a shallowest_idle_cpu before searching for least_loaded_cpu
...
* device-properties:
leds: leds-gpio: Fix multiple instances registration without 'label' property
leds: leds-gpio: Fix legacy GPIO number case
ACPI / property: Drop size_prop from acpi_dev_get_property_reference()
leds: leds-gpio: Convert gpio_blink_set() to use GPIO descriptors
ACPI / GPIO: Document ACPI GPIO mappings API
net: rfkill: gpio: Add default GPIO driver mappings for ACPI
ACPI / GPIO: Driver GPIO mappings for ACPI GPIOs
input: gpio_keys_polled: Make use of device property API
leds: leds-gpio: Make use of device property API
gpio: Support for unified device properties interface
Driver core: Unified interface for firmware node properties
input: gpio_keys_polled: Add support for GPIO descriptors
leds: leds-gpio: Add support for GPIO descriptors
gpio: sch: Consolidate core and resume banks
gpio / ACPI: Add support for _DSD device properties
misc: at25: Make use of device property API
ACPI: Allow drivers to match using Device Tree compatible property
Driver core: Unified device properties interface for platform firmware
ACPI: Add support for device specific properties
rtnl_link_get_net() holds a reference on the 'struct net', we need to release
it in case of error.
CC: Eric W. Biederman <ebiederm@xmission.com>
Fixes: b51642f6d7 ("net: Enable a userns root rtnl calls that are safe for unprivilged users")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Several small fixes here:
1) Don't crash in tg3 driver when the number of tx queues has been
configured to be different from the number of rx queues. From
Thadeu Lima de Souza Cascardo.
2) VLAN filter not disabled properly in promisc mode in ixgbe driver,
from Vlad Yasevich.
3) Fix OOPS on dellink op in VTI tunnel driver, from Xin Long.
4) IPV6 GRE driver WCCP code checks skb->protocol for ETH_P_IP
instead of ETH_P_IPV6, whoops. From Yuri Chislov.
5) Socket matching in ping driver is buggy when packet AF does not
match socket's AF. Fix from Jane Zhou.
6) Fix checksum calculation errors in VXLAN due to where the
udp_tunnel6_xmit_skb() helper gets it's saddr/daddr from. From
Alexander Duyck.
7) Fix 5G detection problem in rtlwifi driver, from Larry Finger.
8) Fix NULL deref in tcp_v{4,6}_send_reset, from Eric Dumazet.
9) Various missing netlink attribute verifications in bridging code,
from Thomas Graf.
10) tcp_recvmsg() unconditionally calls ipv4 ip_recv_error even for
ipv6 sockets, whoops. Fix from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net-timestamp: make tcp_recvmsg call ipv6_recv_error for AF_INET6 socks
bridge: Sanitize IFLA_EXT_MASK for AF_BRIDGE:RTM_GETLINK
bridge: Add missing policy entry for IFLA_BRPORT_FAST_LEAVE
net: Check for presence of IFLA_AF_SPEC
net: Validate IFLA_BRIDGE_MODE attribute length
bridge: Validate IFLA_BRIDGE_FLAGS attribute length
stmmac: platform: fix default values of the filter bins setting
net/mlx4_core: Limit count field to 24 bits in qp_alloc_res
net: dsa: bcm_sf2: reset switch prior to initialization
net: dsa: bcm_sf2: fix unmapping registers in case of errors
tg3: fix ring init when there are more TX than RX channels
tcp: fix possible NULL dereference in tcp_vX_send_reset()
rtlwifi: Change order in device startup
rtlwifi: rtl8821ae: Fix 5G detection problem
Revert "netfilter: conntrack: fix race in __nf_conntrack_confirm against get_next_corpse"
vxlan: Fix boolean flip in VXLAN_F_UDP_ZERO_CSUM6_[TX|RX]
ip6_udp_tunnel: Fix checksum calculation
net-timestamp: Fix a documentation typo
net/ping: handle protocol mismatching scenario
af_packet: fix sparse warning
...
Add a new directory heirarchy under the debugfs sunrpc/ directory:
sunrpc/
rpc_xprt/
<xprt id>/
Within that directory, we can put files that give info about the
xprts. We do have the (minor) problem that there is no succinct,
unique identifier for rpc_xprts. So we generate them synthetically
with a static atomic_t counter.
For now, this directory just holds an "info" file, but we may add
other files to it in the future.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
It's possible to get a dump of the RPC task queue by writing a value to
/proc/sys/sunrpc/rpc_debug. If you write any value to that file, you get
a dump of the RPC client task list into the log buffer. This is a rather
inconvenient interface however, and makes it hard to get immediate info
about the task queue.
Add a new directory hierarchy under debugfs:
sunrpc/
rpc_clnt/
<clientid>/
Within each clientid directory we create a new "tasks" file that will
dump info similar to what shows up in the log buffer, but with a few
small differences -- we avoid printing raw kernel addresses in favor of
symbolic names and the XID is also displayed.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
These patches various bugfixes and cleanups for using NFS over RDMA, including
better error handling and performance improvements by using pad optimization.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=YIru
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-for-3.19' of git://git.linux-nfs.org/projects/anna/nfs-rdma into linux-next
Pull NFS client RDMA changes for 3.19 from Anna Schumaker:
"NFS: Client side changes for RDMA
These patches various bugfixes and cleanups for using NFS over RDMA, including
better error handling and performance improvements by using pad optimization.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>"
* tag 'nfs-rdma-for-3.19' of git://git.linux-nfs.org/projects/anna/nfs-rdma:
xprtrdma: Display async errors
xprtrdma: Enable pad optimization
xprtrdma: Re-write rpcrdma_flush_cqs()
xprtrdma: Refactor tasklet scheduling
xprtrdma: unmap all FMRs during transport disconnect
xprtrdma: Cap req_cqinit
xprtrdma: Return an errno from rpcrdma_register_external()
These patches fixes for iostats and SETCLIENTID in addition to cleaning
up the nfs4_init_callback() function.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PMdS
-----END PGP SIGNATURE-----
Merge tag 'nfs-cel-for-3.19' of git://git.linux-nfs.org/projects/anna/nfs-rdma into linux-next
Pull pull additional NFS client changes for 3.19 from Anna Schumaker:
"NFS: Generic client side changes from Chuck
These patches fixes for iostats and SETCLIENTID in addition to cleaning
up the nfs4_init_callback() function.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>"
* tag 'nfs-cel-for-3.19' of git://git.linux-nfs.org/projects/anna/nfs-rdma:
NFS: Clean up nfs4_init_callback()
NFS: SETCLIENTID XDR buffer sizes are incorrect
SUNRPC: serialize iostats updates
TCP timestamping introduced MSG_ERRQUEUE handling for TCP sockets.
If the socket is of family AF_INET6, call ipv6_recv_error instead
of ip_recv_error.
This change is more complex than a single branch due to the loadable
ipv6 module. It reuses a pre-existing indirect function call from
ping. The ping code is safe to call, because it is part of the core
ipv6 module and always present when AF_INET6 sockets are active.
Fixes: 4ed2d765 (net-timestamp: TCP timestamping)
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
It may also be worthwhile to add WARN_ON_ONCE(sk->family == AF_INET6)
to ip_recv_error.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only search for IFLA_EXT_MASK if the message actually carries a
ifinfomsg header and validate minimal length requirements for
IFLA_EXT_MASK.
Fixes: 6cbdceeb ("bridge: Dump vlan information from a bridge port")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: c2d3babf ("bridge: implement multicast fast leave")
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Payload is currently accessed blindly and may exceed valid message
boundaries.
Fixes: 407af3299 ("bridge: Add netlink interface to configure vlans on bridge ports")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull nfsd bugfixes from Bruce Fields:
"These fix one mishandling of the case when security labels are
configured out, and two races in the 4.1 backchannel code"
* 'for-3.18' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix slot wake up race in the nfsv4.1 callback code
SUNRPC: Fix locking around callback channel reply receive
nfsd: correctly define v4.2 support attributes
Occasionally mountstats reports a negative retransmission rate.
Ensure that two RPCs completing concurrently don't confuse the sums
in the transport's op_metrics array.
Since pNFS filelayout can invoke rpc_count_iostats() on another
transport from xprt_release(), we can't rely on simply holding the
transport_lock in xprt_release(). There's nothing for it but hard
serialization. One spin lock per RPC operation should make this as
painless as it can be.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
After commit ca777eff51 ("tcp: remove dst refcount false sharing for
prequeue mode") we have to relax check against skb dst in
tcp_v[46]_send_reset() if prequeue dropped the dst.
If a socket is provided, a full lookup was done to find this socket,
so the dst test can be skipped.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88191
Reported-by: Jaša Bartelj <jasa.bartelj@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Daniel Borkmann <dborkman@redhat.com>
Fixes: ca777eff51 ("tcp: remove dst refcount false sharing for prequeue mode")
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5195c14c8b.
If the conntrack clashes with an existing one, it is left out of
the unconfirmed list, thus, crashing when dropping the packet and
releasing the conntrack since golden rule is that conntracks are
always placed in any of the existing lists for traceability reasons.
Reported-by: Daniel Borkmann <dborkman@redhat.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=88841
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP checksum calculation for VXLAN tunnels is currently using the
socket addresses instead of the actual packet source and destination
addresses. As a result the checksum calculated is incorrect in some
cases.
Also uh->check was being set twice, first it was set to 0, and then it is
set again in udp6_set_csum. This change removes the redundant assignment
to 0.
Fixes: acbf74a7 ("vxlan: Refactor vxlan driver to make use of the common UDP tunnel functions.")
Cc: Andy Zhou <azhou@nicira.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An async error upcall is a hard error, and should be reported in
the system log.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The Linux NFS/RDMA server used to reject NFSv3 WRITE requests when
pad optimization was enabled. That bug was fixed by commit
e560e3b510 ("svcrdma: Add zero padding if the client doesn't send
it").
We can now enable pad optimization on the client, which helps
performance and is supported now by both Linux and Solaris servers.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Currently rpcrdma_flush_cqs() attempts to avoid code duplication,
and simply invokes rpcrdma_recvcq_upcall and rpcrdma_sendcq_upcall.
1. rpcrdma_flush_cqs() can run concurrently with provider upcalls.
Both flush_cqs() and the upcalls were invoking ib_poll_cq() in
different threads using the same wc buffers (ep->rep_recv_wcs
and ep->rep_send_wcs), added by commit 1c00dd0776 ("xprtrmda:
Reduce calls to ib_poll_cq() in completion handlers").
During transport disconnect processing, this sometimes resulted
in the same reply getting added to the rpcrdma_tasklets_g list
more than once, which corrupted the list.
2. The upcall functions drain only a limited number of CQEs,
thanks to the poll budget added by commit 8301a2c047
("xprtrdma: Limit work done by completion handler").
Fixes: a7bc211ac9 ("xprtrdma: On disconnect, don't ignore ... ")
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=276
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Restore the separate function that schedules the reply handling
tasklet. I need to call it from two different paths.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When using RPCRDMA_MTHCAFMR memory registration, after a few
transport disconnect / reconnect cycles, ib_map_phys_fmr() starts to
return EINVAL because the provider has exhausted its map pool.
Make sure that all FMRs are unmapped during transport disconnect,
and that ->send_request remarshals them during an RPC retransmit.
This resets the transport's MRs to ensure that none are leaked
during a disconnect.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Recent work made FRMR registration and invalidation completions
unsignaled. This greatly reduces the adapter interrupt rate.
Every so often, however, a posted send Work Request is allowed to
signal. Otherwise, the provider's Work Queue will wrap and the
workload will hang.
The number of Work Requests that are allowed to remain unsignaled is
determined by the value of req_cqinit. Currently, this is set to the
size of the send Work Queue divided by two, minus 1.
For FRMR, the send Work Queue is the maximum number of concurrent
RPCs (currently 32) times the maximum number of Work Requests an
RPC might use (currently 7, though some adapters may need more).
For mlx4, this is 224 entries. This leaves completion signaling
disabled for 111 send Work Requests.
Some providers hold back dispatching Work Requests until a CQE is
generated. If completions are disabled, then no CQEs are generated
for quite some time, and that can stall the Work Queue.
I've seen this occur running xfstests generic/113 over NFSv4, where
eventually, posting a FAST_REG_MR Work Request fails with -ENOMEM
because the Work Queue has overflowed. The connection is dropped
and re-established.
Cap the rep_cqinit setting so completions are not left turned off
for too long.
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=269
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The RPC/RDMA send_request method and the chunk registration code
expects an errno from the registration function. This allows
the upper layers to distinguish between a recoverable failure
(for example, temporary memory exhaustion) and a hard failure
(for example, a bug in the registration logic).
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
It's always set to the same value as CONFIG_TRACEPOINTS, so we can just
use that instead.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
It's always set to whatever CONFIG_SUNRPC_DEBUG is, so just use that.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
ping_lookup() may return a wrong sock if sk_buff's and sock's protocols
dont' match. For example, sk_buff's protocol is ETH_P_IPV6, but sock's
sk_family is AF_INET, in that case, if sk->sk_bound_dev_if is zero, a wrong
sock will be returned.
the fix is to "continue" the searching, if no matching, return NULL.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Jane Zhou <a17711@motorola.com>
Signed-off-by: Yiwei Zhao <gbjc64@motorola.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
af_packet produces lots of these:
net/packet/af_packet.c:384:39: warning: incorrect type in return expression (different modifiers)
net/packet/af_packet.c:384:39: expected struct page [pure] *
net/packet/af_packet.c:384:39: got struct page *
this seems to be because sparse does not realize that _pure
refers to function, not the returned pointer.
Tweak code slightly to avoid the warning.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using GRE redirection in WCCP, it sets the wrong skb->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Yuri Chislov <yuri.chislov@gmail.com>
Tested-by: Yuri Chislov <yuri.chislov@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tracepoints inside the main loop on xs_tcp_data_recv that allow
us to keep an eye on what's happening during each phase of it.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
...so we can keep track of when calls are sent and replies received.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
...just around svc_send, svc_recv and svc_process for now.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Now the vti_link_ops do not point the .dellink, for fb tunnel device
(ip_vti0), the net_device will be removed as the default .dellink is
unregister_netdevice_queue,but the tunnel still in the tunnel list,
then if we add a new vti tunnel, in ip_tunnel_find():
hlist_for_each_entry_rcu(t, head, hash_node) {
if (local == t->parms.iph.saddr &&
remote == t->parms.iph.daddr &&
link == t->parms.link &&
==> type == t->dev->type &&
ip_tunnel_key_match(&t->parms, flags, key))
break;
}
the panic will happen, cause dev of ip_tunnel *t is null:
[ 3835.072977] IP: [<ffffffffa04103fd>] ip_tunnel_find+0x9d/0xc0 [ip_tunnel]
[ 3835.073008] PGD b2c21067 PUD b7277067 PMD 0
[ 3835.073008] Oops: 0000 [#1] SMP
.....
[ 3835.073008] Stack:
[ 3835.073008] ffff8800b72d77f0 ffffffffa0411924 ffff8800bb956000 ffff8800b72d78e0
[ 3835.073008] ffff8800b72d78a0 0000000000000000 ffffffffa040d100 ffff8800b72d7858
[ 3835.073008] ffffffffa040b2e3 0000000000000000 0000000000000000 0000000000000000
[ 3835.073008] Call Trace:
[ 3835.073008] [<ffffffffa0411924>] ip_tunnel_newlink+0x64/0x160 [ip_tunnel]
[ 3835.073008] [<ffffffffa040b2e3>] vti_newlink+0x43/0x70 [ip_vti]
[ 3835.073008] [<ffffffff8150d4da>] rtnl_newlink+0x4fa/0x5f0
[ 3835.073008] [<ffffffff812f68bb>] ? nla_strlcpy+0x5b/0x70
[ 3835.073008] [<ffffffff81508fb0>] ? rtnl_link_ops_get+0x40/0x60
[ 3835.073008] [<ffffffff8150d11f>] ? rtnl_newlink+0x13f/0x5f0
[ 3835.073008] [<ffffffff81509cf4>] rtnetlink_rcv_msg+0xa4/0x270
[ 3835.073008] [<ffffffff8126adf5>] ? sock_has_perm+0x75/0x90
[ 3835.073008] [<ffffffff81509c50>] ? rtnetlink_rcv+0x30/0x30
[ 3835.073008] [<ffffffff81529e39>] netlink_rcv_skb+0xa9/0xc0
[ 3835.073008] [<ffffffff81509c48>] rtnetlink_rcv+0x28/0x30
....
modprobe ip_vti
ip link del ip_vti0 type vti
ip link add ip_vti0 type vti
rmmod ip_vti
do that one or more times, kernel will panic.
fix it by assigning ip_tunnel_dellink to vti_link_ops' dellink, in
which we skip the unregister of fb tunnel device. do the same on ip6_vti.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds SKB_GSO_TCPV4 to the list of supported GSO types handled by
the IPv6 GSO offloads. Without this change VXLAN tunnels running over IPv6
do not currently handle IPv4 TCP TSO requests correctly and end up handing
the non-segmented frame off to the device.
Below is the before and after for a simple netperf TCP_STREAM test between
two endpoints tunneling IPv4 over a VXLAN tunnel running on IPv6 on top of
a 1Gb/s network adapter.
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.29 0.88 Before
87380 16384 16384 10.03 895.69 After
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix BUG when decrypting empty packets in mac80211, from Ronald Wahl.
2) nf_nat_range is not fully initialized and this is copied back to
userspace, from Daniel Borkmann.
3) Fix read past end of b uffer in netfilter ipset, also from Dan
Carpenter.
4) Signed integer overflow in ipv4 address mask creation helper
inet_make_mask(), from Vincent BENAYOUN.
5) VXLAN, be2net, mlx4_en, and qlcnic need ->ndo_gso_check() methods to
properly describe the device's capabilities, from Joe Stringer.
6) Fix memory leaks and checksum miscalculations in openvswitch, from
Pravin B SHelar and Jesse Gross.
7) FIB rules passes back ambiguous error code for unreachable routes,
making behavior confusing for userspace. Fix from Panu Matilainen.
8) ieee802154fake_probe() doesn't release resources properly on error,
from Alexey Khoroshilov.
9) Fix skb_over_panic in add_grhead(), from Daniel Borkmann.
10) Fix access of stale slave pointers in bonding code, from Nikolay
Aleksandrov.
11) Fix stack info leak in PPP pptp code, from Mathias Krause.
12) Cure locking bug in IPX stack, from Jiri Bohac.
13) Revert SKB fclone memory freeing optimization that is racey and can
allow accesses to freed up memory, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (71 commits)
tcp: Restore RFC5961-compliant behavior for SYN packets
net: Revert "net: avoid one atomic operation in skb_clone()"
virtio-net: validate features during probe
cxgb4 : Fix DCB priority groups being returned in wrong order
ipx: fix locking regression in ipx_sendmsg and ipx_recvmsg
openvswitch: Don't validate IPv6 label masks.
pptp: fix stack info leak in pptp_getname()
brcmfmac: don't include linux/unaligned/access_ok.h
cxgb4i : Don't block unload/cxgb4 unload when remote closes TCP connection
ipv6: delete protocol and unregister rtnetlink when cleanup
net/mlx4_en: Add VXLAN ndo calls to the PF net device ops too
bonding: fix curr_active_slave/carrier with loadbalance arp monitoring
mac80211: minstrel_ht: fix a crash in rate sorting
vxlan: Inline vxlan_gso_check().
can: m_can: update to support CAN FD features
can: m_can: fix incorrect error messages
can: m_can: add missing delay after setting CCCR_INIT bit
can: m_can: fix not set can_dlc for remote frame
can: m_can: fix possible sleep in napi poll
can: m_can: add missing message RAM initialization
...
Commit c3ae62af8e ("tcp: should drop incoming frames without ACK
flag set") was created to mitigate a security vulnerability in which a
local attacker is able to inject data into locally-opened sockets by
using TCP protocol statistics in procfs to quickly find the correct
sequence number.
This broke the RFC5961 requirement to send a challenge ACK in response
to spurious RST packets, which was subsequently fixed by commit
7b514a886b ("tcp: accept RST without ACK flag").
Unfortunately, the RFC5961 requirement that spurious SYN packets be
handled in a similar manner remains broken.
RFC5961 section 4 states that:
... the handling of the SYN in the synchronized state SHOULD be
performed as follows:
1) If the SYN bit is set, irrespective of the sequence number, TCP
MUST send an ACK (also referred to as challenge ACK) to the remote
peer:
<SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK>
After sending the acknowledgment, TCP MUST drop the unacceptable
segment and stop processing further.
By sending an ACK, the remote peer is challenged to confirm the loss
of the previous connection and the request to start a new connection.
A legitimate peer, after restart, would not have a TCB in the
synchronized state. Thus, when the ACK arrives, the peer should send
a RST segment back with the sequence number derived from the ACK
field that caused the RST.
This RST will confirm that the remote peer has indeed closed the
previous connection. Upon receipt of a valid RST, the local TCP
endpoint MUST terminate its connection. The local TCP endpoint
should then rely on SYN retransmission from the remote end to
re-establish the connection.
This patch lets SYN packets through the discard added in c3ae62af8e,
so that spurious SYN packets are properly dealt with as per the RFC.
The challenge ACK is sent unconditionally and is rate-limited, so the
original vulnerability is not reintroduced by this patch.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not sure what I was thinking, but doing anything after
releasing a refcount is suicidal or/and embarrassing.
By the time we set skb->fclone to SKB_FCLONE_FREE, another cpu
could have released last reference and freed whole skb.
We potentially corrupt memory or trap if CONFIG_DEBUG_PAGEALLOC is set.
Reported-by: Chris Mason <clm@fb.com>
Fixes: ce1a4ea3f1 ("net: avoid one atomic operation in skb_clone()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains two bugfixes for your net tree, they are:
1) Validate netlink group from nfnetlink to avoid an out of bound array
access. This should only happen with superuser priviledges though.
Discovered by Andrey Ryabinin using trinity.
2) Don't push ethernet header before calling the netfilter output hook
for multicast traffic, this breaks ebtables since it expects to see
skb->data pointing to the network header, patch from Linus Luessing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-11-20
Please full this little batch of fixes intended for the 3.18 stream!
For the mac80211 patch, Johannes says:
"Here's another last minute fix, for minstrel HT crashing
depending on the value of some uninitialised stack."
On top of that...
Ben Greear fixes an ath9k regression in which a BSSID mask is
miscalculated.
Dmitry Torokhov corrects an error handling routing in brcmfmac which
was checking an unsigned variable for a negative value.
Johannes Berg avoids a build problem in brcmfmac for arches where
linux/unaligned/access_ok.h and asm/unaligned.h conflict.
Mathy Vanhoef addresses another brcmfmac issue so as to eliminate a
use-after-free of the URB transfer buffer if a timeout occurs.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an old regression introduced by commit
b0d0d915 (ipx: remove the BKL).
When a recvmsg syscall blocks waiting for new data, no data can be sent on the
same socket with sendmsg because ipx_recvmsg() sleeps with the socket locked.
This breaks mars-nwe (NetWare emulator):
- the ncpserv process reads the request using recvmsg
- ncpserv forks and spawns nwconn
- ncpserv calls a (blocking) recvmsg and waits for new requests
- nwconn deadlocks in sendmsg on the same socket
Commit b0d0d915 has simply replaced BKL locking with
lock_sock/release_sock. Unlike now, BKL got unlocked while
sleeping, so a blocking recvmsg did not block a concurrent
sendmsg.
Only keep the socket locked while actually working with the socket data and
release it prior to calling skb_recv_datagram().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When userspace doesn't provide a mask, OVS datapath generates a fully
unwildcarded mask for the flow by copying the flow and setting all bits
in all fields. For IPv6 label, this creates a mask that matches on the
upper 12 bits, causing the following error:
openvswitch: netlink: Invalid IPv6 flow label value (value=ffffffff, max=fffff)
This patch ignores the label validation check for masks, avoiding this
error.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pim6_protocol was added when initiation, but it not deleted.
Similarly, unregister RTNL_FAMILY_IP6MR rtnetlink.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
depending on the value of some uninitialised stack.
-----BEGIN PGP SIGNATURE-----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=L2Jb
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-john-2014-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Here's another last minute fix, for minstrel HT crashing
depending on the value of some uninitialised stack."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both xprt_lookup_rqst() and xprt_complete_rqst() require that you
take the transport lock in order to avoid races with xprt_transmit().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Linus Torvalds