Intel Apollo Lake also requires XHCI_PME_STUCK_QUIRK.
Adding its PCI ID to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device is unplugged and replugged during Sx system suspend
some Intel xHC hosts will overwrite the CAS (Cold attach status) flag
and no device connection is noticed in resume.
A device in this state can be identified in resume if its link state
is in polling or compliance mode, and the current connect status is 0.
A device in this state needs to be warm reset.
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Observed on Cherryview and Apollolake as they go into compliance mode
if LFPS times out during polling, and re-plugged devices are not
discovered at resume.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC in Wildcatpoint-LP PCH is similar to LynxPoint-LP and need the
same quirks to prevent machines from spurious restart while
shutting them down.
Reported-by: Hasan Mahmood <hasan.mahm@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the Linux PCI core does not touch power state of PCI bridges and
PCIe ports when system suspend is entered. Leaving them in D0 consumes
power unnecessarily and may prevent the CPU from entering deeper C-states.
With recent PCIe hardware we can power down the ports to save power given
that we take into account few restrictions:
- The PCIe port hardware is recent enough, starting from 2015.
- Devices connected to PCIe ports are effectively in D3cold once the port
is transitioned to D3 (the config space is not accessible anymore and
the link may be powered down).
- Devices behind the PCIe port need to be allowed to transition to D3cold
and back. There is a way both drivers and userspace can forbid this.
- If the device behind the PCIe port is capable of waking the system it
needs to be able to do so from D3cold.
This patch adds a new flag to struct pci_device called 'bridge_d3'. This
flag is set and cleared by the PCI core whenever there is a change in power
management state of any of the devices behind the PCIe port. When system
later on is suspended we only need to check this flag and if it is true
transition the port to D3 otherwise we leave it in D0.
Also provide override mechanism via command line parameter
"pcie_port_pm=[off|force]" that can be used to disable or enable the
feature regardless of the BIOS manufacturing date.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.
Tests on another motherboard show that it does work with streams disabled.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Broxton B0 also requires XHCI_PME_STUCK_QUIRK.
Adding PCI device ID for Broxton B and adding to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Broxton M was verifed to require XHCI_PME_STUCK_QUIRK quirk as well.
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI_SSIC_PORT_UNUSED quirk was applied to the xHCI host controllers
in some Intel SoC chips. With this quirk applied, SSIC port is set
to "unused" prior to xhci_suspend(). This may cause problem if host
fails to suspend. In this case, the port is set to unused without
host further entering D3, and the port will not be usable anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two workarounds introduced by commit b8cb91e058 ("xhci: Workaround
for PME stuck issues in Intel xhci") and commit abce329c27 ("xhci:
Workaround to get D3 working in Intel xHCI") share a single quirk bit
XHCI_PME_STUCK_QUIRK. These two workarounds actually are different and
might happen on different hardwares. Need to separate them by adding a
quirk bit for the later.
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit abce329c27 ("xhci: Workaround to get D3 working in Intel xHCI")
adds a workaround for a limitation of PME storm caused by SSIC port in
some Intel SoCs. This commit only handled one SSIC port, while there
are actually two SSIC ports in the chips. This patch handles both SSIC
ports. Without this fix, users still see PME storm.
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a memory leak because acpi_evaluate_dsm() actually returns an
object which the caller is supposed to release. Fix this by calling
ACPI_FREE() for the returned object (this expands to kfree() so passing
NULL there is fine as well).
While there correct indentation in !CONFIG_ACPI case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.2
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleanups the hcd private size to suitable size.
The previous code has "sizeof(struct xhci_hcd *)" in xhci_hc_driver
as hcd_priv_size and sizeof(struct xhci_hcd) in xhci_plat_overrides
or xhci_pci_overrides as extra_priv_size. However, the xhci driver
uses a "sizeof(struct xhcd_hcd)" memory space in each hcd
(main_hcd and shared_hcd) actually.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We received several reports of systems rebooting and powering on
after an attempted shutdown. Testing showed that setting
XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT
quirk allowed the system to shutdown as expected for LynxPoint-LP
xHCI controllers. Set the quirk back.
Note that the quirk was originally introduced for LynxPoint and
LynxPoint-LP just for this same reason. See:
commit 638298dc66 ("xhci: Fix spurious wakeups after S5 on Haswell")
It was later limited to only concern HP machines as it caused
regression on some machines, see both bug and commit:
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
commit 6962d914f3 ("xhci: Limit the spurious wakeup fix only to HP machines")
Later it was discovered that the powering on after shutdown
was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP
machine suffered from spontaneous resume from S3 (which should
not be related to the SPURIOUS_WAKEUP quirk at all). An attempt
to fix this then removed the SPURIOUS_WAKEUP flag usage completely.
commit b45abacde3 ("xhci: no switching back on non-ULT Haswell")
Current understanding is that LynxPoint-LP (Haswell ULT) machines
need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and
plain Lynxpoint (Haswell) machines may _not_ have the quirk
set otherwise they again will restart.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Oliver Neukum <oneukum@suse.com>
[Added more history to commit message -Mathias]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the controller speed to HCD_USB31 to if host hardware supports USB 3.1
For PCI xhci controllers the USB 3.1 support is checked from SBRN bits in
pci config space. Platform controllers will need to set xhci->sbrn == 0x31
to indicate USB 3.1 support before calling xhci_gen_setup().
Also make sure xhci driver works correctly with speed set to HCD_USB31
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_pme_quirk() is only used when CONFIG_PM is defined.
Compiling a kernel without PM complains about this function
[reworded commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Tomer Barletz <barletz@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI in Intel CherryView / Braswell Platform requires
a driver workaround to get xHCI D3 working. Without this
workaround, xHCI might not enter D3.
Workaround is to configure SSIC PORT as "unused" before D3
entry and "used" after D3 exit. This is done through a
vendor specific register (PORT2_SSIC_CONFIG_REG2 at offset
0x883c), in xhci suspend / resume callbacks.
Verified xHCI D3 works fine in CherryView / Braswell platform.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel xhci hw that require XHCI_PME_STUCK quirk have as default disabled
xhci from going to D3 state in runtime suspend. Driver needs to verify
it can deal with the hw by calling an ACPI _DSM method to get D3 enabled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HCD core allocates memory for HCD private data in
usb_create_[shared_]hcd() so make use of that
mechanism to allocate the struct xhci_hcd.
Introduce struct xhci_driver_overrides to provide
the size of HCD private data and hc_driver operation
overrides. As of now we only need to override the
reset and start methods.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device with an isochronous endpoint is plugged into the Intel
xHCI host controller, and the driver submits multiple frames per URB,
the xHCI driver will set the Block Event Interrupt (BEI) flag on all
but the last TD for the URB. This causes the host controller to place
an event on the event ring, but not send an interrupt. When the last
TD for the URB completes, BEI is cleared, and we get an interrupt for
the whole URB.
However, under Intel xHCI host controllers, if the event ring is full
of events from transfers with BEI set, an "Event Ring is Full" event
will be posted to the last entry of the event ring, but no interrupt
is generated. Host will cease all transfer and command executions and
wait until software completes handling the pending events in the event
ring. That means xHC stops, but event of "event ring is full" is not
notified. As the result, the xHC looks like dead to user.
This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And
it should be backported to kernels as old as 3.0, that contains the
commit 69e848c209 ("Intel xhci: Support EHCI/xHCI port switching.").
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Alistair Grant <akgrant0710@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.
Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks
Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams do not work reliabe on Fresco Logic FL1000G xhci controllers,
trying to use them results in errors like this:
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3570 9067b000 00000000 05000000 01078001
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3580 9067b400 00000000 05000000 01038001
As always I've ordered a pci-e addon card with a Fresco Logic controller for
myself to see if I can come up with a better fix then the big hammer, in
the mean time this will make uas devices work again (in usb-storage mode)
for FL1000G users.
Reported-by: Marcin Zajączkowski <mszpak@wp.pl>
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit ff8cbf250b ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Cc: stable <stable@vger.kernel.org> # v3.2+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of building all of the xHCI code into a single module, separate
it out into the core (xhci-hcd), PCI (xhci-pci, now selected by the new
config option CONFIG_USB_XHCI_PCI), and platform (xhci-plat) drivers.
Also update the PCI/platform drivers with module descriptions/licenses
and have them register their respective drivers in their initcalls.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of calling xhci_compliance_mode_recovery_timer_quirk_check() again
in the PCI suspend path, just check for XHCI_COMP_MODE_QUIRK which will
have been set based on xhci_compliance_mode_recovery_timer_quirk_check()
in xhci_init().
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the struct hc_driver is mostly the same across the xhci-pci,
xhci-plat, and the upcoming xhci-tegra driver, introduce the function
xhci_init_driver() which will populate the hc_driver with the default
xHCI operations. The caller must supply a setup function which will
be used as the hc_driver's reset callback.
Note that xhci-plat also overrides the default ->start() callback so
that it can do rcar-specific initialization.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a bit bigger hammer then I would like to use for this, but for now
it will have to make do. I'm working on getting my hands on one of these so
that I can try to get streams to work (with a quirk flag if necessary) and
then we can re-enable them.
For now this at least makes uas capable disk enclosures work again by forcing
fallback to the usb-storage driver.
https://bugzilla.kernel.org/show_bug.cgi?id=79511
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD xHC also needs short tx quirk after tested on most of chipset
generations. That's because there is the same incorrect behavior like
Fresco Logic host. Please see below message with on USB webcam
attached on xHC host:
[ 139.262944] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.266934] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.270913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.274937] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.278914] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.282936] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.286915] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.290938] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.294913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.298917] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
Reported-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Shriraj-Rai P <shriraj-rai.p@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 7023 product id is the generic product id for the Etron EJ168, it is
not specific to the version found on the Asrock P67 motherboard. The same id
is e.g. also used on Gigabyte motherboards and on no-name pci-e usb-3 addon
cards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams on the EJ168 do not work as they should. I've spend 2 days trying
to get them to work, but without success.
The first problem is that when ever you ring the stream-ring doorbell, the
controller starts executing trbs at the beginning of the first ring segment,
event if it ended somewhere else previously. This can be worked around by
allowing enqueing only one td (not a problem with how streams are typically
used) and then resetting our copies of the enqueueing en dequeueing pointers
on a td completion to match what the controller seems to be doing.
This way things seem to start working with uas and instead of being able
to complete only the very first scsi command, the scsi core can probe the disk.
But then things break later on when td-s get enqueued with more then one
trb. The controller does seem to increase its dequeue pointer while executing
a stream-ring (data transfer events I inserted for debugging do trigger).
However execution seems to stop at the final normal trb of a multi trb td,
even if there is a data transfer event inserted after the final trb.
The first problem alone is a serious deviation from the spec, and esp.
dealing with cancellation would have been very tricky if not outright
impossible, but the second problem simply is a deal breaker altogether,
so this patch simply disables streams.
Note this will cause the usb-storage + uas driver pair to automatically switch
to using usb-storage instead of uas on these devices, essentially reverting
to the 3.14 and earlier behavior when uas was marked CONFIG_BROKEN.
https://bugzilla.redhat.com/show_bug.cgi?id=1121288https://bugzilla.kernel.org/show_bug.cgi?id=80101
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch "xhci: Switch Intel Lynx Point ports to EHCI on shutdown."
commit c09ec25d36 is not fully correct
It switches both Lynx Point and Lynx Point-LP ports to EHCI on shutdown.
On some Lynx Point machines it causes spurious interrupt,
which wake the system: bugzilla.kernel.org/show_bug.cgi?id=76291
On Lynx Point-LP on the contrary switching ports to EHCI seems to be
necessary to fix these spurious interrupts.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Reported-by: Wulf Richartz <wulf.richartz@gmail.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Either we log for all chips we set the quirk for or for
none. This patch reports it for all chips.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same issue like with Panther Point chipsets. If the USB ports are
switched to xHCI on shutdown, the xHCI host will send a spurious interrupt,
which will wake the system. Some BIOS have work around for this, but not all.
One example is Compulab's mini-desktop, the Intense-PC2.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.
This patch should be backported to stable kernels as old as 3.12,
that contain the commit 638298dc66
"xhci: Fix spurious wakeups after S5 on Haswell"
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI driver has its own pci probe function that will call usb_hcd_pci_probe
to register its usb-2 bus, and then continue to manually register the
usb-3 bus. usb_hcd_pci_probe does a pm_runtime_put_noidle at the end and
might thus trigger a runtime suspend before the usb-3 bus is ready.
Prevent the runtime suspend by increasing the usage count in the
beginning of xhci_pci_probe, and decrease it once the usb-3 bus is
ready.
xhci-platform driver is not using usb_hcd_pci_probe to set up
busses and should not need to have it's usage count increased during probe.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
On some older XHCIs streams are not supported and the UAS driver
will fail at probe time. For those devices storage should try
to bind to UAS devices.
This patch adds a flag for stream support to HCDs and evaluates
it.
[Note: Sarah fixed a bug where the USB 2.0 root hub, not USB 3.0 root
hub would get marked as being able to support streams.]
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The xHCI driver currently uses a USB core internal field,
udev->lpm_capable, to indicate the xHCI driver knows how to calculate
the LPM timeout values. If this value is set for the host controller
udev, it means Link PM can be enabled for child devices under that host.
Change the code so the xHCI driver isn't mucking with USB core internal
fields. Instead, indicate the xHCI driver doesn't support Link PM on
this host by clearing the U1 and U2 exit latencies in the roothub
SuperSpeed Extended Capabilities BOS descriptor.
The code to check for the roothub setting U1 and U2 exit latencies to
zero will also disable LPM for external devices that do that same. This
was already effectively done with commit
ae8963adb4 "usb: Don't enable LPM if the
exit latency is zero." Leave that code in place, so that if a device
sets one exit latency value to zero, but the other is set to a valid
value, LPM is only enabled for the U1 or U2 state that had the valid
value. This is the same behavior the code had before.
Also, change messages about missing Link PM information from warning
level to info level. Only print a warning about the first device that
doesn't support LPM, to avoid log spam. Further, cleanup some
unnecessary line breaks to help people to grep for the error messages.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Don Zickus <dzickus@redhat.com> writes:
Some co-workers of mine bought Samsung laptops that had mostly usb3 ports.
Those ports did not resume correctly (the driver would timeout communicating
and fail). This led to frustration as suspend/resume is a common use for
laptops.
Poking around, I applied the reset on resume quirk to this chipset and the
resume started working. Reloading the xhci_hcd module had been the temporary
workaround.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable # 2.6.37
Change the default enumeration scheme for xhci attached non-SuperSpeed
devices from:
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(8)
GetDescriptor(18)
...to:
Reset
[xhci address-device BSR = 1]
GetDescriptor(64)
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(18)
...as some devices misbehave when encountering a SetAddress command
prior to GetDescriptor. There are known legacy devices that require
this scheme, but testing has found at least one USB3 device that fails
enumeration when presented with this ordering. For now, follow the ehci
case and enable 'new scheme' by default for non-SuperSpeed devices.
To support this enumeration scheme on xhci the AddressDevice operation
needs to be performed twice. The first instance of the command enables
the HC's device and slot context info for the device, but omits sending
the device a SetAddress command (BSR == block set address request).
Then, after GetDescriptor completes, follow up with the full
AddressDevice+SetAddress operation.
As mentioned before, this ordering of events with USB3 devices causes an
extra state transition to be exposed to xhci. Previously USB3 devices
would transition directly from 'enabled' to 'addressed' and never need
to underrun responses to 'get descriptor'. We do see the 64-byte
descriptor fetch the correct data, but the following 18-byte descriptor
read after the reset gets:
bLength = 0
bDescriptorType = 0
bcdUSB = 0
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
instead of:
bLength = 12
bDescriptorType = 1
bcdUSB = 300
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
which results in the discovery process looping until falling back to
'old scheme' enumeration.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Moore <david.moore@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
We've got regression reports that my previous fix for spurious wakeups
after S5 on HP Haswell machines leads to the automatic reboot at
shutdown on some machines. It turned out that the fix for one side
triggers another BIOS bug in other side. So, it's exclusive.
Since the original S5 wakeups have been confirmed only on HP machines,
it'd be safer to apply it only to limited machines. As a wild guess,
limiting to machines with HP PCI SSID should suffice.
This patch should be backported to kernels as old as 3.12, that
contain the commit 638298dc66 "xhci: Fix
spurious wakeups after S5 on Haswell".
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: <dashing.meng@gmail.com>
Reported-by: Niklas Schnelle <niklas@komani.de>
Reported-by: Giorgos <ganastasiouGR@gmail.com>
Reported-by: <art1@vhex.net>
Haswell LynxPoint and LynxPoint-LP with the recent Intel BIOS show
mysterious wakeups after shutdown occasionally. After discussing with
BIOS engineers, they explained that the new BIOS expects that the
wakeup sources are cleared and set to D3 for all wakeup devices when
the system is going to sleep or power off, but the current xhci driver
doesn't do this properly (partly intentionally).
This patch introduces a new quirk, XHCI_SPURIOUS_WAKEUP, for
fixing the spurious wakeups at S5 by calling xhci_reset() in the xhci
shutdown ops as done in xhci_stop(), and setting the device to PCI D3
at shutdown and remove ops.
The PCI D3 call is based on the initial fix patch by Oliver Neukum.
[Note: Sarah changed the quirk name from XHCI_HSW_SPURIOUS_WAKEUP to
XHCI_SPURIOUS_WAKEUP, since none of the other quirks have system names
in them. Sarah also fixed a collision with a quirk submitted around the
same time, by changing the xhci->quirks bit from 17 to 18.]
This patch should be backported to kernels as old as 3.0, that
contain the commit 1c12443ab8 "xhci: Add
Lynx Point to list of Intel switchable hosts."
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
It has been reported that this chipset really cannot
sleep without this extraordinary delay.
This patch should be backported, in order to ensure this host functions
under stable kernels. The last quirk for Fresco Logic hosts (commit
bba18e33f2 "xhci: Extend Fresco Logic MSI
quirk.") was backported to stable kernels as old as 2.6.36.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP. The corresponding change has already
been made for ohci-hcd.
Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
