Commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device tree")
changed the behavior of "cd-inverted" to follow the device tree bindings
specification:
According to SDHCI standard, CD lines are specified as "active low".
Using the "cd-inverted" property means that the CD line is "active high".
Fix the SD card description for meson by setting the cd-gpios as
"active low", according to the boards specifications, and dropping the
"cd-inverted" property.
Fixes: 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Extend configuring the MAC address from u-boot to all meson boards.
I didn't test this changeset but having checked libretech's u-boot
tree I believe it should just work.
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the amlogic,tx-delay-ns property with the old (hardcoded)
default value of 2ns to all boards which are using an RGMII ethernet
PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There is one blue LED on the front of the device. Keep it lit and
configure it as panic indicator.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All boards from the Tronsmart Vega S95 series are sharing similar MMC
based hardware.
sd_emmc_a is used to connect a Broadcom based SDIO wifi card (supported
by the brcmfmac driver). The 32.768KHz LPO clock for the wifi chip is
generated by PWM_E.
sd_emmc_b is routed to the SD-card. Unlike p20x there is no GPIO
regulator, meaning it only supports 3.3V (which seems to be hard-wired).
The eMMC chip is connected to sd_emmc_c and is implemented similar to
the meson-gxbb-p20x boards (meaning that hard-wired fixed regulators
are used).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node to rgmii
specific naming in all boards dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All of these have a Realtek Gbit RGMII PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the Infrared Remote Controller on boards which have an Infrared
receiver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Apparently, it's not valid to have an alias point to a disabled device.
Fix this by moving the aliases that are used (serial0) into the files
that use them, and remove aliases to disabled devices (serial1).
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add Device Trees for Tronsmart Vega S95 Pro, Meta and Telos TV boxes.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Loys Ollivier