Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxC+
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
IB/core: Re-enable create_flow/destroy_flow uverbs
IB/core: extended command: an improved infrastructure for uverbs commands
IB/core: Remove ib_uverbs_flow_spec structure from userspace
IB/core: Use a common header for uverbs flow_specs
IB/core: Make uverbs flow structure use names like verbs ones
IB/core: Rename 'flow' structs to match other uverbs structs
IB/core: clarify overflow/underflow checks on ib_create/destroy_flow
IB/ucma: Convert use of typedef ctl_table to struct ctl_table
IB/cm: Convert to using idr_alloc_cyclic()
IB/mlx5: Fix page shift in create CQ for userspace
IB/mlx4: Fix device max capabilities check
IB/mlx5: Fix list_del of empty list
IB/mlx5: Remove dead code
IB/core: Encorce MR access rights rules on kernel consumers
IB/mlx4: Fix endless loop in resize CQ
RDMA/cma: Remove unused argument and minor dead code
RDMA/ucma: Discard events for IDs not yet claimed by user space
IB/core: Add Cisco usNIC rdma node and transport types
RDMA/nes: Remove self-assignment from nes_query_qp()
IB/srp: Report receive errors correctly
...
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSiXSwAAoJEGgI9fZJve1bJBgQAJKXIYXqZG5AwCqtFXltN0S5
qYmxiaxUekQyesBxRNNb6LwgWEBUF+lQtmfhDpSaHwi6aRc7pmSQaVw6tfD1dpBe
bAEHrWu1YD8v6rwhrhB91kv9F81ea06pfUtyUAwDpbchGq/VaN/tsUT4uO5E/AIT
K7tWZzjmGyQ79186HUnDxmgb0lA1PPDypsuv/pP1KgrioKNPHskDqhLeS2YuCe6J
WUHiGb3cDB8Tu2+Af5OIxXio5J74486KvjlH1K9+ziixUrU0P380D26JshklgIsG
qWc1hu9DSO+r76N7HV0EzbpJNqZNEFJiXaXSozgA/yRtJy+ISEIVXJE9oDwW7SxH
thLveZTck6VQ6CyggAh2nn9KPVrpFYUcy+HFshpM7V4xugjcAe9Bq9i5cWwJHvn9
Xy4G2s2MS81PFdKEGc9JjSwvXULTRTMAe5gMMfwAqnn+Xuf2+KSCtTlOnPkON/sa
cNraBFTSVi33yCEHS9BO7BKbb5ikPNtAaAB+4VszwMQbUysPld7WvEpEOIUOaoJO
EYgsM1VOLV0cYO5Qwu9Yxplrjmz/l+kNxAgtCW21SV14DjUbnV9ZuhL5Gx4jbLyY
T1uiREtzpTUGoKhZHqWHKXtoEUW+d48nkDXbO+IbKmKPTF6bn0TuZmW0sNU/ZHb8
yNJPZKinHfUE6heJCX2X
=rT+j
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Highlights:
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups"
* tag 'for-v3.13' of git://git.infradead.org/battery-2.6:
pm2301-charger: Remove unneeded NULL checks
twl4030_charger: Add devicetree support
power_supply: Fix documentation for TEMP_*ALERT* properties
max17042_battery: Support regmap to access device's registers
max17042_battery: Use SIMPLE_DEV_PM_OPS
charger-manager : Replace kzalloc to devm_kzalloc and remove uneccessary code
bq2415x_charger: Fix max battery regulation voltage
tps65090-charger: Use "IS_ENABLED(CONFIG_OF)" for DT code
tps65090-charger: Drop devm_free_irq of devm_ allocated irq
power_supply: Add support for bq24735 charger
pm2301-charger: Staticize pm2xxx_charger_die_therm_mngt
pm2301-charger: Check return value of regulator_enable
ab8500-charger: Remove redundant break
ab8500-charger: Check return value of regulator_enable
isp1704_charger: Fix driver to work with changes introduced in v3.5
Pull media build fixes from Mauro Carvalho Chehab:
"A series of patches that fix compilation on non-x86 archs.
While most of them are just build fixes, there are some fixes for real
bugs, as there are a number of drivers using dynamic stack allocation.
A few of those might be considered a security risk, if the i2c-dev
module is loaded, as someone could be sending very long I2C data that
could potentially overflow the Kernel stack. Ok, as using /dev/i2c-*
devnodes usually requires root on usual distros, and exploiting it
would require a DVB board or USB stick, the risk is not high"
* 'topic/kbuild-fixes-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (28 commits)
[media] platform drivers: Fix build on frv arch
[media] lirc_zilog: Don't use dynamic static allocation
[media] mxl111sf: Don't use dynamic static allocation
[media] af9035: Don't use dynamic static allocation
[media] af9015: Don't use dynamic static allocation
[media] dw2102: Don't use dynamic static allocation
[media] dibusb-common: Don't use dynamic static allocation
[media] cxusb: Don't use dynamic static allocation
[media] v4l2-async: Don't use dynamic static allocation
[media] cimax2: Don't use dynamic static allocation
[media] tuner-xc2028: Don't use dynamic static allocation
[media] tuners: Don't use dynamic static allocation
[media] av7110_hw: Don't use dynamic static allocation
[media] stv090x: Don't use dynamic static allocation
[media] stv0367: Don't use dynamic static allocation
[media] stb0899_drv: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] s5h1420: Don't use dynamic static allocation
[media] uvc/lirc_serial: Fix some warnings on parisc arch
...
After merging the final tree, today's linux-next build (sparc64 defconfig)
failed like this:
arch/sparc/mm/init_64.c: In function 'pte_alloc_one':
arch/sparc/mm/init_64.c:2568:9: error: unused variable 'pte' [-Werror=unused-variable]
Caused by the merge between commit 37b3a8ff3e ("sparc64: Move from 4MB
to 8MB huge pages") and commit 1ae9ae5f7d ("sparc: handle
pgtable_page_ctor() fail") (I had the following merge fix in linux-next,
but it didn't seem to propagate upstream - may have forgotten to point it
out :-().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Commit ea1e7ed337 triggers build regression on sparc64.
include/linux/mm.h:1391:2: error: implicit declaration of function 'pgtable_cache_init' [-Werror=implicit-function-declaration]
arch/sparc/include/asm/pgtable_64.h:978:13: error: conflicting types for 'pgtable_cache_init' [-Werror]
It happens due headers include loop:
<linux/mm.h> -> <asm/pgtable.h> -> <asm/pgtable_64.h> ->
<asm/tlbflush.h> -> <asm/tlbflush_64.h> -> <linux/mm.h>
Let's drop <linux/mm.h> include from asm/tlbflush_64.h.
Build tested with allmodconfig.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull EDAC driver updates from Mauro Carvalho Chehab:
- sb_edac: add support for Ivy Bridge support
- cell_edac: add a missing of_node_put() call
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
cell_edac: fix missing of_node_put
sb_edac: add support for Ivy Bridge
sb_edac: avoid decoding the same error multiple times
sb_edac: rename mci_bind_devs()
sb_edac: enable multiple PCI id tables to be used
sb_edac: rework sad_pkg
sb_edac: allow different interleave lists
sb_edac: allow different dram_rule arrays
sb_edac: isolate TOHM retrieval
sb_edac: rename pci_br
sb_edac: isolate TOLM retrieval
sb_edac: make RANK_CFG_A value part of sbridge_info
Highlights:
* Support for Calxeda ECX-2000 memory controller, from Robert Richter
* Misc Calxeda Highbank drivers and EDAC core cleanups, from Rob Herring
and Robert Richter
* New maintainer for Freescale's MPC85xx EDAC driver: Johannes Thumshirn
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=pU/h
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"Following up on last week's discussion, here's my part of the EDAC
pile, highlights in the signed tag.
The last two patches have a date from just now because I've just
applied them to the tree after Johannes sent them to me earlier. I
decided to forward them now because they're trivial.
There's a third one for MPC85xx which adds PCIe error interrupt
support but since it is not so trivial and hasn't seen any linux-next
time, I'm deferring it to 3.14
EDAC update highlights:
- Support for Calxeda ECX-2000 memory controller, from Robert Richter
- Misc Calxeda Highbank drivers and EDAC core cleanups, from Rob
Herring and Robert Richter
- New maintainer for Freescale's MPC85xx EDAC driver: Johannes
Thumshirn"
* tag 'edac_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
edac/85xx: Remove mpc85xx_pci_err_remove
EDAC: Add edac-mpc85xx driver to MAINTAINERS
edac, highbank: Moving error injection to sysfs for edac
edac, highbank: Add MAINTAINERS entry
edac: Unify reporting of device info for device, mc and pci
edac, highbank: Improve and unify naming
edac, highbank: Add Calxeda ECX-2000 support
ARM: dts: calxeda: move memory-controller node out of ecx-common.dtsi
edac, highbank: Fix interrupt setup of mem and l2 controller
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=JDGc
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.13:
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield"
* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
mmc: wbsd: Silence compiler warning
mmc: core: Silence compiler warning in __mmc_switch
mmc: sh_mmcif: Convert to clk_prepare|unprepare
mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
mmc: dw_mmc: exynos: Revert the sdr_timing assignment
mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
mmc: Don't force card to active state when entering suspend/shutdown
MIPS: db1235: Don't use MMC_CLKGATE
mmc: core: Remove deprecated mmc_suspend|resume_host APIs
mmc: mmci: Move away from using deprecated APIs
mmc: via-sdmmc: Move away from using deprecated APIs
mmc: tmio: Move away from using deprecated APIs
mmc: sh_mmcif: Move away from using deprecated APIs
mmc: sdricoh_cs: Move away from using deprecated APIs
mmc: rtsx: Remove redundant suspend and resume callbacks
mmc: wbsd: Move away from using deprecated APIs
mmc: pxamci: Remove redundant suspend and resume callbacks
...
Unlike other chips supported by this driver, the NCT6791 only has a single
set of registers to configure weighted fan control. Enable it only for the
single channel supporting it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The number of SMIOVT registers on NCT6779 and NCT6791 is limited to 2.
As result, the driver may not report some of the temperatures used
for fan control. This can result in some of the pwmX_temp_sel or
pwm2_weight_temp_sel attributes to wrongly return 0.
Fortunately, the chip has registers to monitor those temperatures.
Add them to the list of temperatures to report.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This was tested on a NETGEAR ReadyNAS 2120 device (Marvell Armada XP
based board, via DT).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Secondary unicast MAC addresses will get deleted only when the interface is UP.
When the interface is DOWN, though these secondary MAC addresses are unusable
and awaiting to be deleted, cause the firmware to believe that they are being used.
If the user intends to set a MAC address as primary MAC from one of these
secondary MAC addresses, the firmware returns a MAC address Collision error.
Delete these secondary MAC addresses during be_close.
The secondary MAC addresses list will be refreshed during interface open anyway.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently requests the firmware to enable rx_interface options
without considering if the interface was created with that capability.
This could cause commands to firmware to fail.
To avoid this, enable only those options on an interface if the interface
was created with that capability.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must have one to fill out the adjusted_mode.crtc_clock. And with
the tv encoder fixed up every encoder we have has a ->get_config
callback. So we can drop the checks.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this to properly fill in adjusted_mode.crtc_clock, otherwise
the state checker gets unhappy. This seems to have been forgotten in
the big clock rework in
commit 18442d0878
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 13 16:00:08 2013 +0300
drm/i915: Fix port_clock and adjusted_mode.clock readout all over
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is more appropriate to use # of queue pairs currently used by
the driver instead of a magic value.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A plain read() on a socket does set msg->msg_name to NULL. So check for
NULL pointer first.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
bnx2x: Bug fixes patch series
This series contains several fixes, relating either to SR-IOV flows
or to critical sections protected by the rtnl lock.
Please consider applying these patches to `net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver release rtnl lock in between DCB re-configuration.
As a result, other flows (e.g., mtu config) may enter in between and fail
due to halted tx path for dcb configuration.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During VF load, prior to sending messages on HW channel to PF the VF
checks its bulletin board to see whether the PF indicated it has closed;
If a closed PF is encountered, the VF skips sending the message.
Due to incorrect return values, there's a possible scenario in which the VF
finishes loading "successfully", while the PF hasn't actually fully configured
FW/HW for the VFs supposed configuration.
Once VF tries to send Tx packets, HW will raise an attention (and FW possibly
will start treat the VF as malicious).
The patch fails the loading process in such a scenario.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If chip enters a recovery flow just after the driver issues a DMAE request
the DMAE will timeout. Current code will cause a bnx2x_panic() as a result,
which means interface will no longer be usable (regardless of the recovery
results), as bnx2x_panic() is irreversible for the driver.
As this is a possible flow, the panic should be reached only when driver
is compiled with STOP_ON_ERROR.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While unloading, bnx2x needs to clean the sp_rtnl_state to prevent
configuration made before the unload to be applied afterwards with
stale values.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6d0bfe2261
net: ipv6: Add IPv6 support to the ping socket
introduced a change in the cleanup logic of inet6_init and
has a bug in that ipv6_packet_cleanup() may not be called.
Fix the cleanup ordering.
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
CC: Lorenzo Colitti <lorenzo@google.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions named similar to other drivers to access
superio registers.
Request memory region only when needed, and use request_muxed_region().
This lets other devices (hwmon, gpio) use the same region.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to enable the watchdog device if it is already enabled.
Also, when enabling the watchdog device, only set the watchdog device
enable bit and do not touch other bits; depending on the chip type,
those bits may enable other functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is unnecessary to enable the logical device and WDT0 each time
the watchdog is accessed. Do it only once during initialization.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Sparse pointed out that the new flags variable I had added
shadowed an existing one, rename the new one to avoid that,
making the code clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free temporary 'chanspecs' avoiding leakage.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only update *addr_len when we actually fill in sockaddr, otherwise we
can return uninitialized memory from the stack to the caller in the
recvfrom, recvmmsg and recvmsg syscalls. Drop the the (addr_len == NULL)
checks because we only get called with a valid addr_len pointer either
from sock_common_recvmsg or inet_recvmsg.
If a blocking read waits on a socket which is concurrently shut down we
now return zero and set msg_msgnamelen to 0.
Reported-by: mpb <mpb.mail@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_SYSCTL=n the following build warning happens:
net/ipv6/ndisc.c:1730:1: warning: label 'out' defined but not used [-Wunused-label]
The 'out' label is only used when CONFIG_SYSCTL=y, so move it inside the
'ifdef CONFIG_SYSCTL' block.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data type of max_sectors and max_hw_sectors in queue settings are
unsigned int. But these values are passed to __bio_add_page() as an
argument whose data type is unsigned short. In the worst case such as
max_sectors is 0x10000, bio_add_page() can't add a page and IOs can't
proceed.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix to return a negative error code from the bus speed parse
error handling case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There was a bug in xennet_alloc_rx_buffers, when allocating page or
sk_buff failed, and at the same time rx_batch queue not empty,
the rx_refill_timer timer won't be scheduled. If finally the remaining
request buffers in rx ring less than what backend driver expected,
the backend driver would think of rx ring as full and start dropping packets.
In such situation, there is no way for the netfront driver to recover
automatically, so that the device can not work properly.
The patch fixes the problem by always scheduling rx_refill_timer timer when
alloc_page or __netdev_alloc_skb fails, no matter whether rx_batch queue is
empty or not. It ensures that the rx ring request buffers will finally meet
the backend needs.
Signed-off-by: Ma JieYue <jieyue.majy@alibaba-inc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a straight goto error label style in nfsd_setattr to make sure
we always do the put_write_access call after we got it earlier.
Note that the we have been failing to do that in the case
nfsd_break_lease() returns an error, a bug introduced into 2.6.38 with
6a76bebefe "nfsd4: break lease on nfsd
setattr".
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Split out two helpers to make the code more readable and easier to verify
for correctness.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Michael L Semon reported that generic/069 runtime increased on v5
superblocks by 100% compared to v4 superblocks. his perf-based
analysis pointed directly at the timestamp updates being done by the
write path in this workload. The append writers are doing 4-byte
writes, so there are lots of timestamp updates occurring.
The thing is, they aren't being triggered by timestamp changes -
they are being triggered by the inode change counter needing to be
updated. That is, every write(2) system call needs to bump the inode
version count, and it does that through the timestamp update
mechanism. Hence for v5 filesystems, test generic/069 is running 3
orders of magnitude more timestmap update transactions on v5
filesystems due to the fact it does a huge number of *4 byte*
write(2) calls.
This isn't a real world scenario we really need to address - anyone
doing such sequential IO should be using fwrite(3), not write(2).
i.e. fwrite(3) buffers the writes in userspace to minimise the
number of write(2) syscalls, and the problem goes away.
However, there is a small change we can make to improve the
situation - removing the expensive lock operation on the change
counter update. All inode version counter changes in XFS occur
under the ip->i_ilock during a transaction, and therefore we
don't actually need the spin lock that provides exclusive access to
it through inc_inode_iversion().
Hence avoid the lock and just open code the increment ourselves when
logging the inode.
Reported-by: Michael L. Semon <mlsemon35@gmail.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
v5 filesystems use 512 byte inodes as a minimum, so read inodes in
clusters that are effectively half the size of a v4 filesystem with
256 byte inodes. For v5 fielsystems, scale the inode cluster size
with the size of the inode so that we keep a constant 32 inodes per
cluster ratio for all inode IO.
This only works if mkfs.xfs sets the inode alignment appropriately
for larger inode clusters, so this functionality is made conditional
on mkfs doing the right thing. xfs_repair needs to know about
the inode alignment changes, too.
Wall time:
create bulkstat find+stat ls -R unlink
v4 237s 161s 173s 201s 299s
v5 235s 163s 205s 31s 356s
patched 234s 160s 182s 29s 317s
System time:
create bulkstat find+stat ls -R unlink
v4 2601s 2490s 1653s 1656s 2960s
v5 2637s 2497s 1681s 20s 3216s
patched 2613s 2451s 1658s 20s 3007s
So, wall time same or down across the board, system time same or
down across the board, and cache hit rates all improve except for
the ls -R case which is a pure cold cache directory read workload
on v5 filesystems...
So, this patch removes most of the performance and CPU usage
differential between v4 and v5 filesystems on traversal related
workloads.
Note: while this patch is currently for v5 filesystems only, there
is no reason it can't be ported back to v4 filesystems. This hasn't
been done here because bringing the code back to v4 requires
forwards and backwards kernel compatibility testing. i.e. to
deterine if older kernels(*) do the right thing with larger inode
alignments but still only using 8k inode cluster sizes. None of this
testing and validation on v4 filesystems has been done, so for the
moment larger inode clusters is limited to v5 superblocks.
(*) a current default config v4 filesystem should mount just fine on
2.6.23 (when lazy-count support was introduced), and so if we change
the alignment emitted by mkfs without a feature bit then we have to
make sure it works properly on all kernels since 2.6.23. And if we
allow it to be changed when the lazy-count bit is not set, then it's
all kernels since v2 logs were introduced that need to be tested for
compatibility...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
xfs_trans_ijoin() activates the inode in a transaction and
also can specify which lock to free when the transaction is
committed or canceled.
xfs_bmap_add_attrfork call locks and adds the lock to the
transaction but also manually removes the lock. Change the
routine to not add the lock to the transaction and manually
remove lock on completion.
While here, clean up the xfs_trans_cancel flags and goto names.
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
This is required to properly calculate the tiling parameters
in userspace.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is required to properly calculate the tiling parameters
in userspace.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Should we need to share dma buffers using prime, let's make them prime
aware.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Add prime exporting and imporing operations to surfaces
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Also provide a completely dumb dma-buf ops implementation.
Once we have other virtual dma-buf aware devices, we need to provide
something better.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
We're using the ACPI interface to detect whether we're dealing with a Thinkpad
or not. This way we're not loading the thinkpad_acpi module when we're not on
a Thinkpad, but at the same time, we give the opportunity to check for, and
potentially enable, both present and future Thinkpad with mute/micmute LEDs.
At least those running the ALC269 family (269 to 299) of Realtek codecs.
Cc: Alex Hung <alex.hung@canonical.com>
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch 0ca743a55991: "netfilter: nf_tables: add compatibility
layer for x_tables", leads to the following Smatch
warning: "net/netfilter/nft_compat.c:140 nft_parse_compat()
warn: signedness bug returning '(-34)'"
This nft_parse_compat function returns error codes but the return
type is u8 so the error codes are transformed into small positive
values. The callers don't check the return.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Linus Torvalds